DVB is a registered trademark of the DVB Project
ID Number(s): 5495: 60PG30FD-AA 5496: 50PG30FD-AA 5205: 50PG60UD-AA 5206: 42PG60UD-AA 5209: 42PG20D-AA 5210 : 50PG20D-AA 5522: 60PG70FD-AB 5523: 50PG70FD-AB
PLASMA TV
OWNER’S MANUAL
PLASMA TV MODELS
42PG2***
50PG2***
50PG3***
60PG3***
42PG6***
50PG6***
50PG7***
60PG7***
Please read this manual carefully before operating your TV.
Retain it for future reference.
Record model number and serial number of the TV. Refer to the label on the back cover and quote this information.
To your dealer when requiring service.
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the product.
A Image shown may differ from your TV.
RA
TIO
or
Owner’s Manual |
Batteries |
Remote Control
Power Cord
Ferrite Core
(This feature is not available for all models.)
This feature is not available for all models.
|
* Lightly wipe any stains or fingerprints on the |
|
|
surface of the TV with the polishing cloth. |
|
Polishing Cloth |
Do not use excessive force. This may cause |
|
scratching or discolouration. |
||
Polishing cloth for use on |
||
the screen. |
|
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord.
The closer the location of the ferrite core to the power plug, the better it is.
Cable management clip
(only 42/50PG6***, |
(only 50/60PG3***, |
(only 50PG6***, |
50/60PG7***) |
42/50PG2***) |
50/60PG7*** ) |
|
Protection Cover |
|
|
or |
|
plug closely.
Cable Holder
Except 50PG6***, 50/60PG7***
42PG6*** : 1EA 50/60PG3*** : 2EA 42PG2*** : 1EA 50PG2*** : 2EA
<![endif]>ACCESSORIES
1
|
CONTENTS |
|
|
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 1 |
|
PREPARATION |
|
<![if ! IE]> <![endif]>CONTENTS |
|
|
|
Front Panel Controls..................................................... |
4 |
|
Back Panel Information ................................................ |
5 |
|
Back Cover for Wire Arrangement ............................ |
6 |
|
Desktop Pedestal Installation ..................................... |
9 |
|
Swivel Stand ................................................................... |
9 |
|
Wall Mount: Horizontal Installation........................ |
10 |
|
Please set it up carefully so the product does not |
|
|
fall over............................................................................ |
11 |
|
Antenna Connection................................................... |
12 |
|
EXTERNAL EQUIPMENT SETUP |
|
|
HD Receiver Setup ...................................................... |
13 |
|
DVD Setup..................................................................... |
15 |
|
VCR Setup ..................................................................... |
18 |
|
AV Output Setup ........................................................ |
20 |
|
Digital Audio Out Setup............................................ |
21 |
|
Other A/V Source Setup .......................................... |
22 |
|
USB in Setup ................................................................ |
23 |
|
PC Setup........................................................................ |
24 |
|
- Screen Setup for PC Mode .............................. |
27 |
|
WATCHING TV / PROGRAMME CONTROL |
|
|
Remote Control Key Functions................................ |
32 |
|
Turning on the TV....................................................... |
36 |
|
Programme Selection ................................................ |
36 |
|
Volume Adjustment ................................................... |
36 |
|
Quick Menu ................................................................. |
37 |
|
On-Screen Menus Selection and Adjustment..... |
38 |
|
Auto Programme Tuning............................................ |
39 |
|
Manual Programme Tuning (In Digital Mode)..... |
40 |
|
Manual Programme Tuning (In Analogue Mode) ... |
41 |
|
Programme Edit ........................................................... |
43 |
|
Booster........................................................................... |
46 |
|
Software Update.......................................................... |
47 |
|
Diagnostics ................................................................... |
48 |
|
Selecting the Programme Table............................... |
49 |
|
Input List........................................................................ |
50 |
|
................................................................. |
51 |
|
Input Label .................................................................... |
54 |
2 |
AV Mode........................................................................ |
55 |
TO USE THE USB DEVICE |
|
When connecting the USB device.......................... |
56 |
Photo List ...................................................................... |
57 |
Music List........................................................................ |
61 |
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE)
- Switch on/off EPG ............................................... |
64 |
- Select a programme............................................. |
64 |
- Button Function in NOW/NEXT Guide Mode 65 |
|
- Button Function in 7 Day Guide Mode.......... |
65 |
- Button Function in Date Change Mode......... |
65 |
- Button Function in Extended Description Box . 66 |
|
- Button Function in Remind Setting Mode................. |
66 |
- Button Function in Remind List Mode ............. |
66 |
PICTURE CONTROL |
|
Picture Size (Aspect Ratio) Control....................... |
67 |
Preset Picture Settings |
|
- Picture Mode-Preset............................................ |
69 |
- Auto Colour Tone Control |
|
(Cool/Medium/Warm) ........................................ |
70 |
Manual Picture Adjustment |
|
- Picture Mode-User option................................. |
71 |
- Picture Mode-Expert Control ........................... |
72 |
Picture Improvement Technology........................... |
73 |
Advanced - Film Mode............................................... |
74 |
Advanced - Black(Darkness) Level ......................... |
75 |
Picture Reset................................................................. |
76 |
Image Sticking Minimization (ISM) Method ......... |
77 |
Power Saving Picture Mode...................................... |
78 |
SOUND & LANGUAGE CONTROL |
|
Auto Volume Leveller.................................................. |
79 |
Preset Sound Settings - Sound Mode................... |
80 |
Sound Setting Adjustment - User Mode .............. |
81 |
Clear Voice.................................................................... |
82 |
Balance........................................................................... |
83 |
TV Speakers On/ Off Setup...................................... |
84 |
Selecting Digital Audio Out ..................................... |
85 |
Audio Reset................................................................... |
86 |
Stereo Reception (In Analogue Mode Only) ...... |
87 |
Speaker Sound Output Selection........................... |
87 |
TIME SETTING |
|
Clock Setup .................................................................. |
88 |
Auto On/ Off Timer Setting..................................... |
89 |
Auto Shut-off Setting ................................................. |
90 |
Time Zone Setup......................................................... |
91 |
Sleep Timer Setting..................................................... |
91 |
PARENTAL CONTROL / RATINGS |
|
Set Password & Lock System................................... |
92 |
Block Programme......................................................... |
93 |
Parental Control .......................................................... |
94 |
Key Lock......................................................................... |
95 |
TELETEXT |
|
Switch On/Off ............................................................. |
96 |
SIMPLE Text.................................................................. |
96 |
TOP Text........................................................................ |
96 |
FASTEXT ........................................................................ |
97 |
Special Teletext Functions......................................... |
97 |
APPENDIX |
|
Troubleshooting........................................................... |
98 |
Maintenance ............................................................. |
100 |
Product Specifications ............................................. |
101 |
Programming the Remote Control ....................... |
102 |
IR Codes...................................................................... |
103 |
External Control Through RS-232C .................... |
105 |
Open Source Software Notice ............................... |
112 |
Open Source License................................................ |
113 |
<![endif]>CONTENTS
3
■Image shown may differ from your TV
■If your TV has a protection film attached, remove the film and then wipe the product with a polishing cloth.
<![if ! IE]><![endif]>PREPARATION
Remote Control Sensor |
POWER Button |
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the TV is switched on.
INPUT |
MENU |
OK |
|
P |
|
INPUT |
MENU |
OK |
VOLUME |
PROGRAMME |
4
A Image shown may differ from your TV. |
|
|
|
|||
50/60PG3*** |
||||||
|
|
|
||||
42/50PG2*** |
42/50PG6*** |
|||||
50/60PG7*** |
||||||
|
|
|
|
|
|
USB Input
(Service
only)
50/60PG3*** |
2 |
3 |
42/50PG2*** |
|
|
42/50PG6 |
|
|
*** |
|
|
50/60PG7*** |
|
|
<![if ! IE]> <![endif]>USB |
<![if ! IE]> <![endif]>ONLY |
USB Input |
|
<![if ! IE]> <![endif]>SERVICE |
|||
|
|||
|
<![if ! IE]> <![endif]>3 |
|
HDMI Input
Connect a HDMI signal
to HDMI IN.
S-Video Input
Connect S-Video out from an S-VIDEO device.
|
Audio/Video Input |
|
Connect audio/video |
|
output from an external |
2 |
device to these jacks. |
2 |
|
4 |
5 |
|
|
AV IN 1 |
AV |
AV IN 1 |
AV OUT |
|
or |
|
|
|
||
<![if ! IE]> <![endif]>VIDEO |
<![if ! IE]> <![endif]>VIDEO |
<![if ! IE]> <![endif]>IDEOV |
<![if ! IE]> <![endif]>IDEOV |
|
|
|
|
||||
|
<![if ! IE]> <![endif]>R AUDIO L/MONO |
<![if ! IE]> <![endif]>R AUDIO L |
<![if ! IE]> <![endif]>R UDIOA ONOM/L |
<![if ! IE]> <![endif]>R UDIOA L |
|
|
6 |
7 |
8 |
9 |
10 |
This TV operates on an AC power. The voltage is
indicated on |
Specifications page. Never |
|
attempt to operate the TV |
DC power. |
HDMI Input
Connect a HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable
RGB/DVI Audio Input
Connect the audio from a
OPTICAL DIGITAL AUDIO UT
Connect digital audio from various types of equipment.
Note: In standby mode, |
ports do not work. |
5
Connect a component video/audio device to these jacks.
Connect the output from a PC.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
Audio/Video Input (AV IN 1)
Connect audio/video output from an external device to these jacks.
AV Output
Connect second TV or monitor to the AV OUT socket on the set.
10Antenna Input
Connect RF antenna to this jack.
<![endif]>PREPARATION
5
PREPARATION
<![endif]>PREPARATION
■ Image shown may differ from your TV.
42PG6***
1
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
|
Fix the Cable Holder |
|
CLIP |
as shown and bundle |
|
the cables. |
||
|
How to remove the cable management clip
Hold the CABLE MANAGEMENT CLIP with both hands and pull it upward.
* For the 42PG6*** model, press the center of the CABLE MANAGEMENT CLIP and then lift it.
6
50PG6***, 50/60PG7***
1
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
MANAGEMENT CLIP
How to remove the cable management clip
Hold the CABLE MANAGEMENT |
and pull it upward. |
Separate CABLE MANAGEMENT from TV by pressing two latches.
<![endif]>PREPARATION
7
PREPARATION
<![endif]>PREPARATION
■ Image shown may differ from your TV.
42/50PG2***, 50/60PG3***
1 |
. |
|
EXTERNAL EQUIPMENT SETUP
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
Install the CABLE MANAGEMENT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
shown. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If your TV has the CABLE HOLDER, as shown and bundle the cables.
CABLE HOLDER
CABLE MANAGEMENT CLIP
How to remove the cable management clip
Hold the CABLE MANAGEMENT CLI |
and pull it upward. |
! NOTE
G Do not use the CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
8
AThe TV can be installed in various ways such as on a wall, or on a desktop etc.
AThe TV is designed to be mounted horizontally.
EARTHING
Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
Power Supply
Circuit breaker
<![endif]>PREPARATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
4 inches
4 inches
|
|
|
|
|
|
4 inches |
|
|
|
|
|
|
|
4 inches |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
9
<![endif]>PREPARATION
PREPARATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
|
4 inches |
|
4 inches |
4 inches |
4 inches |
|
|
|
4 inches |
■ Image shown may differ from your TV.
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the PROTECTION COVER into the TV until clicking sound.
10
A You should purchase necessary components to fix the TV to the wall on the market. A Position the TV close to the wall to avoid the possibility of it falling when pushed.
A The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
1 |
2 |
1 |
2 |
1Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
3
3Use a sturdy rope to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
! NOTE
GWhen moving the TV undo the cords first.
GUse a platform or cabinet strong and large enough to support the size and weight of the TV.
GTo use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
<![endif]>PREPARATION
11
PREPARATION
■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied. |
|
|
|
<![if ! IE]> <![endif]>PREPARATION |
|
<![if ! IE]> <![endif]>VIDEO |
<![if ! IE]> <![endif]>VIDEO |
|
|
AV IN 1 |
AV OUT |
Wall |
Multi-family Dwellings/Apartments |
<![if ! IE]> <![endif]>L/MONO |
<![if ! IE]> <![endif]>L |
|
|
|
|
Socket |
(Connect to wall antenna socket) |
<![if ! IE]> <![endif]>RAUDIO |
<![if ! IE]> <![endif]>RAUDIO |
|
|||
Antenna |
|
|
|
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF) Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
|
UHF |
Antenna |
Signal |
|
Amplifier |
|
VHF |
AV IN 1 |
AV OUT |
<![if ! IE]> <![endif]>VIDEO |
<![if ! IE]> <![endif]>VIDEO |
<![if ! IE]> <![endif]>L/MONO |
<![if ! IE]> <![endif]>L |
|
<![if ! IE]> <![endif]>AUDIO |
<![if ! IE]> <![endif]>R |
<![if ! IE]> <![endif]>R |
|
■In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above.
■If signal needs to be split for two TVs, use an antenna signal splitter for connection.
12
■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
■This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50PG6*** models.
■Image shown may differ from your TV.
■This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
1 |
Connect the video outputs (Y, PB, PR) of the digital set |
|
top box to the COMPONENT IN VIDEO jacks on the |
|
|
|
|
|
|
TV. |
1 |
|
|
the digital set-top box to the COMPONENT IN AUDIO jacks on the TV.
2
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select Component 1 input source using the INPUT button on the remote control.
If connected to COMPONENT IN 2 input, select Component 2 input source.
Signal |
Component |
HDMI |
|
|
|
|
|
|
480i/576i |
Yes |
No |
480p/576p |
Yes |
Yes |
720p/1080i |
Yes |
Yes |
1080p |
Yes |
Yes |
|
(50Hz/60Hz only) |
(24Hz/30Hz/50Hz/60Hz) |
|
|
|
|
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
13
EXTERNAL EQUIPMENT SETUP
|
1 |
Connect the digital set-top box to HDMI/DVI IN 1, |
||
<![if ! IE]> <![endif]>EXTERNAL |
HDMI |
IN 2, HDMI IN 3 or HDMI IN 4(except |
||
|
||||
|
42/50PG2***) jack on the TV. |
|||
|
|
|||
|
|
|
top box. |
|
<![if ! IE]> <![endif]>SETUPEQUIPMENT |
|
(Refer to the owner’s manual for the digital set-top box.) |
||
|
Select |
HDMI1, HDMI2, HDMI3 or HDMI4(except |
||
|
|
42/50PG2***) input source using the INPUT button on the remote control.
1Connect the digital set-top box to HDMI/DVI IN 1 jack on the TV.
output of the digital set-top box to /DVI) jack on the TV.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1 input source using the INPUT button on the remote control.
1
12
A
<![if ! IE]><![endif]>R UDIOA MONO/L IDEOV
14
1 Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV.
1
audio outputs of the DVD to the NT IN AUDIO jacks on the TV.
Turn on the DVD player, insert a DVD.
2
Select Component 1 input source using the INPUT button on the remote control.
If connected to COMPONENT IN 2 input, select Component 2 input source.
Refer to the DVD player's manual for operating instructions.
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV |
Y |
PB |
PR |
|
|
|
|
|
|
|
|
|
Y |
PB |
PR |
Video output ports |
Y |
B-Y |
R-Y |
on DVD player |
Y |
Cb |
Cr |
|
Y |
Pb |
Pr |
|
|
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
15
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
VIDEO S-VIDEO L R ANT IN
1 |
Connect the S-VIDEO output of the DVD to the S - |
|
VIDEO input on the TV. |
|
|
|
|
|
|
|
ANT OUT |
|
audio outputs of the DVD to the AUDIO |
|
|
1 |
2 |
Turn on the DVD player, insert a DVD.
Select AV2 input source using the INPUT button on the remote control.
Refer to the DVD player's manual for operating |
|
instructions. |
2 |
|
16
Connect the HDMI output of the DVD to the
1HDMI/DVI IN 1, HDMI IN 2, HDMI IN 3 or HDMI IN 4(except 42/50PG2***) jack on the TV.
I1, HDMI2, HDMI3 or HDMI4(except
***) input source using the INPUT button on the remote control.
Refer to the DVD player's manual for operating
instructions.
1
! NOTE
G The TV can receive video and audio signals simultaneously when using a HDMI cable.
G If the DVD does not support Auto HDMI, you must set the output resolution appropriately.
<![endif]>SETUP EQUIPMENT EXTERNAL
17
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
■To avoid picture noise (interference), allow adequate distance between the VCR and TV.
■Typically a frozen still picture from a VCR. If 4:3 picture format is used for an extended period the fixed images on the sides of the screen may remain visible.
AV IN 1 AV OUT |
|
|
|
|
ConnectingVIDEO |
withVIDEOa RF Cable |
|
|
|
<![if ! IE]> <![endif]>L/MONO |
<![if ! IE]> <![endif]>L |
|
|
|
<![if ! IE]> <![endif]>UDIOA |
<![if ! IE]> <![endif]>UDIOA |
|
|
|
<![if ! IE]> <![endif]>R |
<![if ! IE]> <![endif]>R |
ANT OUT |
S-VIDEO VIDEO |
L R |
|
||||
|
|
|
|
|
|
|
1 |
|
|
|
|
|
OUTPUT |
|
|
|
|
SWITCH |
|
Wall Jack
2
Antenna
1Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.
the antenna cable to the ANT IN socket of the VCR.
Press the PLAY button on the VCR and match the appropriate channel between the TV and VCR for viewing.
18
1 |
the AUDIO/VIDEO jacks between TV and |
|
|
|
Match the jack colours (Video = yellow, Audio Left |
|
|
|
= white, and Audio Right = red) |
1 |
|
|
|
|
|
2 |
Insert a video tape into the VCR and press PLAY on |
|
|
|
the VCR. (Refer to the VCR owner’s manual.) |
2 |
|
3 |
Select AV2 input source using the INPUT button on |
|
|
|
the remote control. |
|
|
|
If connected to AV IN 1 input, select AV1 input |
S-VIDEO VIDEO L |
R ANT IN |
|
source. |
||
|
|
|
|
|
|
OUTPUT |
ANT OUT |
|
|
SWITCH |
|
! NOTE
G If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO jack of the TV.
|
VIDEO S-VIDEO |
L |
R ANT IN |
1 |
Connect the S-VIDEO output of the VCR to the S - |
|
|
VIDEO input on the TV set. The picture quality is |
|
|
|
|
|
|
|
|
improved; compared to normal composite (RCA cable) |
|
|
|
input. |
|
ANT OUT |
|
1 |
|
2 |
|
TV. |
|
|
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
Select AV2 input source with using the INPUT button on the remote control.
2
! NOTE
GIf both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received.
<![endif]>SETUP EQUIPMENT EXTERNAL
19
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
The TV has
to hook up
Connect
1jacks
See
AV IN 1
<![if ! IE]><![endif]>R AUDIO L/ VIDEO
NOTE
G Only Digital, Analogue mode can be used for AV out. Component, RGB, HDMI input sources cannot be used for AV out.
G We recommend to use the AV OUT jacks for VCR recording.
AV OUT
<![if ! IE]><![endif]>VIDEO
1
<![if ! IE]><![endif]>UDA
<![if ! IE]><![endif]>OI
<![if ! IE]><![endif]>R
VIDEO |
L |
R |
|
|
|
20
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
1 |
Connect one end of an optical cable to the TV Digital |
|
|
Audio (Optical) Output port. |
|
|
optical cable to the |
AV IN 1 |
|
<![if ! IE]> <![endif]>IDEOV |
|
|
the audio equipment. |
|
|
|
<![if ! IE]> <![endif]>MONO/L |
|
|
1 |
|
menu.(Gp.84). Refer to the external audio equipment |
<![if ! IE]> <![endif]>UDIOA |
|
<![if ! IE]> <![endif]>R |
|
|
instruction manual for operation. |
|
|
|
|
|
|
2 |
CAUTION
GDo not look into the optical output port. Looking at the laser beam may damage your vision.
! NOTE
G When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off.
<![endif]>SETUP EQUIPMENT EXTERNAL
21
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
1
Camcorder
Video Game Set
VIDEO L R
1 |
between TV and external equipment. Match the jack colours . |
|
(Video = yellow, Audio Left = white, and Audio Right = red) |
||
|
2Select AV2 input source with using the INPUT button on the remote control. If connected to AV IN 1 input, select AV1 input source.
3Operate the corresponding external equipment. Refer to external equipment operating guide.
22
Except 42/50PG2***
1
|
|
|
|
|
|
1 Connect |
USB device to the USB IN jacks on the side of TV. |
||||
|
|
|
|
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
23
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
1 |
Connect the RGB output of the PC to the RGB IN |
|
(PC) jack on the TV. |
||
|
audio output to the AUDIO IN the TV.
Turn on the PC and the TV |
2 |
|
Select RGB input source using the INPUT button on the remote control.
AUDIO |
RGB OUTPUT |
1 |
Connect the DVI output of the PC to the HDMI/DVI |
|
IN1 jack on the TV. |
||
|
output to the AUDIO IN the TV.
1 2
Turn on the PC and the TV.
Select HDMI1 input source using the INPUT button on the remote control.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AUDIO |
||
DVI-PC OUTPUT |
|||||||
|
|
|
|
|
|
|
|
24
Supported Display Resolution
RGB-PC, HDMI/DVI-PC mode |
|
|
HDMI/DVI-DTV mode |
|
||
|
|
|
|
|
|
|
Resolution |
Horizontal |
Vertical |
|
Resolution |
Horizontal |
Vertical |
Frequency(kHz) |
Frequency(Hz) |
|
Frequency(kHz) |
Frequency(Hz) |
||
|
|
|
||||
720x400 |
31.468 |
70.08 |
|
640x480 |
31.649 |
59.94 |
|
|
|
|
|
|
|
640x480 |
31.469 |
59.94 |
|
|
31.469 |
60 |
800x600 |
37.879 |
60.31 |
|
720x480 |
31.47 |
59.94 |
1024x768 |
48.363 |
60.00 |
|
31.50 |
60 |
|
|
|
1280x768 |
47.78 |
59.87 |
1360x768 |
47.72 |
59.8 |
|
|
|
1280x1024 |
63.98 |
60.02 |
1400x1050 |
65.317 |
59.979 |
1920x1080 |
66.587 |
59.934 |
(only 50/60PG3***, 50/60PG7***)
720x576 |
31.25 |
50.00 |
|
37.50 |
50.00 |
1280x720 |
44.96 |
59.94 |
|
45.00 |
60 |
|
28.125 |
50.00 |
|
33.72 |
59.94 |
|
33.75 |
60 |
1920x1080 |
27.00 |
24.00 |
|
33.75 |
30 |
|
56.25 |
50.00 |
|
67.433 |
59.94 |
|
67.50 |
60 |
|
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
25
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
! NOTE
G To enjoy vivid picture and sound, connect a PC to the TV.
G Avoid keeping a fixed image on the set’s screen for prolonged periods of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible.
G Connect the PC to the RGB (PC) or HDMI IN (or HDMI/DVI IN) port of the TV; change the resolution.
G There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear.
If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
G The synchronization input waveform for Horizontal and Vertical frequencies are separate.
G Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the TV or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the TV.
G Connect the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV).
G If using a sound card, adjust PC sound as required. G This TV uses a VESA Plug and Play Solution. The TV provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when
using this TV.
G DDC protocol is preset for RGB (Analogue RGB), HDMI (Digital RGB) mode.
G If required, adjust the settings for Plug and Play functionality
G If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV.
G If graphic card on the PC does output analogue and digital RGB simultaneously, set the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.)
G DOS mode may not work depending on the video card if you use a HDMI to DVI cable.
G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality.
G If connected HDMI(1080p, over 12bit) to HDMI jack on the side, screen may abnormal.
26
Returns Position, Size and Phase to the factory default settings.
This function works in the following mode : RGB[PC].
PICTURE |
Move |
OK |
SCREEN |
Move |
RETURN Prev. |
|
|
|
|
||||
E |
|
|
|
Resolution |
|
|
|
|
|
|
|
|
|
• Contrast |
50 |
|
|
|
|
|
• Brightness |
50 |
|
|
Auto Config. |
|
|
• Sharpness |
50 |
|
|
Position |
|
|
• Colour |
50 |
|
|
|
To Set |
|
|
|
|
|
|||
|
|
|
|
|
|
|
• Tint |
0 |
R |
G |
Size |
Yes |
No |
• Advanced Control |
|
|||||
|
|
|
|
|||
• Picture Reset |
|
|
|
Phase |
|
|
ScreenScreen |
|
|
|
|
|
|
|
|
|
|
Reset |
G |
|
Select PICTURE.
Select SCREEN.
Select Reset.
OK
5
OK |
Run Reset. |
|
•Press the MENU button to return to normal TV viewing.
•Press the RETURN button to move to the previous menu screen.
<![endif]>SETUP EQUIPMENT EXTERNAL
27
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually.
This function works in the following mode : RGB[PC].
PICTURE |
Move |
OK |
SCREEN |
|
Move |
RETURN Prev. |
|
|
|
|
|
|
|
||
E |
|
|
|
Resolution |
|
|
|
• Contrast |
50 |
|
|
|
|
|
|
|
|
|
|
|
|
||
• Brightness |
50 |
|
|
Auto Config. |
|
|
|
|
|
|
|
|
|
|
|
• Sharpness |
50 |
|
|
|
|
|
|
• Colour |
50 |
|
|
|
|
|
D |
|
|
Position |
G |
F |
G |
||
• Tint |
0 |
R |
|
G |
|
|
E |
|
|
|
|
||||
• Advanced Control |
|
|
Size |
|
|
|
|
|
|
|
|
|
|
||
• Picture Reset |
|
|
|
Phase |
|
|
|
ScreenScreen |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Reset |
|
|
|
MENU |
Select PICTURE. |
|
|
OK |
Select SCREEN. |
OK |
Select Position, Size or Phase. |
4 |
Make appropriate adjustments. |
•Press the MENU button to return to normal TV viewing.
•Press the RETURN button to move to the previous menu screen.
28