LG 50PA4500-SF Schematic
Internal Use Only
North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
PLASMA TV
SERVICE MANUAL
CHASSIS : PB21A
MODEL : 50PA4500 50PA4500-SF
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Printed in KoreaP/NO : MFL67341904 (1201-REV00)
CONTENTS
CONTENTS .............................................................................................. 2
SAFETY PRECAUTIONS ........................................................................ 3
SPECIFICATION ....................................................................................... 4
ADJUSTMENT INSTRUCTION ................................................................ 5
BLOCK DIAGRAM .................................................................................. 12
EXPLODED VIEW .................................................................................. 13
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
Only for training and service purposes
- 2 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
AC Volt-meter
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damage d by accidental sho rt s of the circui tr y that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 M
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Ω and 5.2 MΩ.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any vol ta ge
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
Good Earth Ground
such as WATER PIPE,
To Instrument's
exposed
METALLIC PARTS
0.15u
CONDUIT etc.
1.5 Kohm/10W
Only for training and service purposes
- 3 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement
1. Application range
This spec sheet is applied all of the PDP TV with PB21A chassis.
2. Requirement for Test
Each part is tested as below without special appointment.
(1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C
(2) Relative Humidity: 65 % ± 10 %
(3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
(4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with
BOM.
(5) The receiver must be operated for about 5 minutes prior to the adjustment.
3. Test method
(1) Performance: LGE TV test method followed
(2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
.
4. Model General Specification
No Item Specication Remark
1 Receiving System 1) SBTVD / NTSC / PAL-M / PAL-N 50A6500-SA
50A4900-SA
2) DVB-T 42/50PA4500-DF
2 Available Channel 1) VHF : 02~13
2) UHF : 14~69
3) DTV : 07-69 (VHF high/UHF)
4) CATV : 02~135
1) VHF : 02~13
2) UHF : 14~69
3) DTV : 14~69 (UHF)
4) CATV : 02~135
3 Input Voltage 1) AC 100 ~ 240V 50/60Hz
4 Market Brazil / chile / Peru / Venezuela / Costarica / Uruguay
5 Screen Size 42 inch Wide(1024 × 768)
50 inch Wide(1024 × 768)
50 inch Wide(1920 × 1080)
60 inch Wide(1920 × 1080)
6 Aspect Ratio 16:9
7 Tuning System FS
8 Module PDP42T4#### (1024 × 768)
PDP50T4#### (1024 × 768)
PDP50R4#### (1920 × 1080)
PDP60R4#### (1920 × 1080)
9 Operating Environ-
ment
10 Storage Environ-
ment
1) Temp : 0 ~ 40 deg
2) Humidity : ~ 80 %
1) Temp : -20 ~ 60 deg
2) Humidity : ~ 85 %
50A6500-SA
50A4900-SA
42/50PA4500-DF
42PA all model
50PA4 all model
50PA6 all model
60PA6 all model
42PA all model
50PA4 all model
50PA6 all model
60PA6 all model
Only for training and service purposes
- 4 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to PB21A chassis applied PDP TV all
models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) T he adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep AC 100-240
V~, 50/60 Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
■ After Receive 100% Full white pattern (06CH) then
process Heat-run
(or “8. Test pattern” condition of Ez-Adjust status)
■ How to make set white pattern
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select “10. Test
pattern” and, after sel ec t “White” using navigation
button, and then you can see 100% Full White pattern.
* In this status you can maintain Heat-Run useless any
pattern generator
* Notice: if you mai ntain one picture over 20 minu te s
(Especially sharp distinction black with whit e
pattern – 13Ch, or Cross hatch pattern – 09Ch)
then it can appear image stick near black level.
3. Adjustment items
3.1. PCB Assembly adjustment
■ Adjust 480i Comp1
■ Adjust 1080p Comp1/RGB
● If it is necessary, it can adjustment at Manufacture Line
● Yo u can see set adjustm en t status at “9. ADJUST
CHECK” of the “In-start menu”
3.2. Set Assembly Adjustment
■ EDID (The Extended Display Identification Data )
■ Color Temperature (White Balance) Adjustment
■ Make sure RS-232C control
■ Selection Factory output option
4. PCB Assembly Adjustment
4.1. Using RS-232C
- Adjust 3 items at 3.1. PCB assembly adjustments
" 4.1. ■ Adjustment sequence" one after the order.
■ Adjustment sequence
Order command Set response
1. Inter the
Adjustment
mode
2. Change the
Source
3. Start
Adjustment
4. Return the
Response
5. Read
Adjustment
data
6. Conrm
Adjustment
7. End of
Adjustment
< See ADC Adjustment RS232C Protocol_Ver1.0 >
■ Necessary items before Adjustment items
● Pattern Generator : (MSPG-925FA)
● Adjust 480i comp1
(MSPG-925FA:model :209, pattern :65) - comp1 Mode
● Adjust 1080p comp1
(MSPG-925FA:model :225 , pattern :65) - comp1 Mode
● Addjust RGB (MSPG-925FA:model :225 , pattern :65)
- RGB-Pc Mode
* If you want more information then see the below Adjustment
method (Factory Adjustment)
■ Adjustment sequence
● aa 00 00: Enter the ADc Adjustment mode.
● xb 00 40: change the mode to component1 (No actions)
● ad 00 10: Adjust 480i comp
● ad 00 10: Adjust 1080p comp
● xb 00 60: change to RGB-Pc mode(No action)
● ad 00 10: Adjust 1080p RGB
● xb 00 90: Endo of Adjustmennt
aa 00 00 a 00 OK00x
XB 00 40
XB 00 60
ad 00 10
( main )
ad 00 20
( main )
ad 00 30
ad 00 99 NG 03 00x (Failed condition)
ad 00 90 d 00 OK90x
b 00 OK40x (Adjust 480i Comp1 )
(Adjust 1080p Comp1)
b 00 OK60x (Adjust 1080p RGB)
OKx ( Success condition )
NGx ( Failed condition )
(main : component1 480i, RGB 1080p)
000000000000000000000000007c007b006dx
(main : component1 1080p)
000000070000000000000000007c00830077x
NG 03 01x (Failed condition)
NG 03 02x (Failed condition)
OK 03 03x (Success condition)
Only for training and service purposes
- 5 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
5. Factory Adjustment
-> PU21A/PB21A : USE INTERNAL ADC(LM1) : using internal
pattern.
5.1. Auto Adjust Component 480i/1080p RGB
1080p
■ Summary : Adjustment component 480i/1080i and RGB
1080p is Gain and Black level setting at Analog
to Digital converter, and compensate the RGB
deviation
■ Using instrument
● Adjustment remocon, 801GF(802B, 802F, 802R) or
MSPG925FA pattern generator
( It can output 480i/1080i hor izontal 100% color bar
pa tter n sig nal , and i ts ou tput leve l mus t set tin g
0.7V±0.1V p-p correctly)
< Adjustment pattern : 480i / 1080p 60Hz Pattern >
● You must make it sure its resolution and pattern cause
every instrument can have different setting
● Adjustment method 480i Comp1, Adjust 1080p Comp1/
RGB (Factory adjustment)
● ADC 480i Component1 adjustment
- Check connection of Component1
- MSPG-925FA -> Model: 209, Pattern 65
● Set Component 480i mode and 100% Horizontal Color
Bar Pattern( H o z T V 3 1 B a r ) , t h e n s e t T V s e t t o
Component1 mode and its screen to “NORMAL”
● ADC 1080p Component1 / RGB adjustment
- Check connection both of Component1 and RGB
- MSPG-925FA -> Model: 225, Pattern 65
● Set Component 1080p mode and 100% Horizontal Color
Bar Pattern( H o z T V 3 1 B a r ) , t h e n s e t T V s e t t o
Component1 mode and its screen to “NORMAL”
● After get each the signal, wait more a second and enter
the “IN-START” with press IN-START key of Service
remoco n. After then select “7. External ADC” wit h
navigator button and press “Enter”.
● After Then Press key of Service remocon “Right Arrow
(VOL+)”
● You can see “ADC Component1 Success”
● Component1 1080p, RGB 1080p Adjust is same method.
● Component 1080p Adjustment in Component1 input
mode
● RGB 1080p adjustment in RGB input mode
● If you success RGB 1080p Adjust. You can see “ADC
RGB-DTV Success”
* caution : Set Volume 0 after adjustment
5.2. Use Internal ADC(S7R)
- A D J ( EZ ADJ U S T ) -> 6. A D C C a l i bration -> ADC
Calibration(START)
* EDI D (The Extended Display Identification Data)/DDC
(Display Data Channel) Download.
■ Summary
● It is established in VESA, for communication between
PC and Monitor without order from user for building
user condition. It helps to make easily use realize
“Plug and Play” function.
● For EDID data write, we use DDC2B protocol.
- Auto Download
■ After enter Service Mode by pushing “ADJ” key,
■ Enter EDID D/L mode.
■ Enter “START” by pushing “OK” key.
* Caution:
- Never connect HDMI & D-sub Cable when the user
downloading .
- Use the proper cables below for EDID Writing
Only for training and service purposes
- 6 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
■ It only needs to PCM EDID D/L for North America Product.
(PU21A)
* Edid data and Model option download(RS232)
NO Enter
download MODE
Item download ‘Mode In’ download
CMD 1 A A
CMD 2 A E
Data 0 0 00
0 10
When transfer the
‘Mode In’,
Carry the command.
- Manual Download
■ Write HDMI EDID data
● Using instruments
- Jig. (PC Serial to D-Sub connection) for PC, DDC
adjustment.
- S/W for DDC recording (EDID data write and read)
- D-sub jack
- Additional HDMI cable connection Jig.
● Preparing and setting.
- Set instruments and Jig. Like pic.5), then turn on PC
and Jig.
- Operate DDC write S/W (EDID write & read)
- It will operate in the DOS mode.
EDID data Model
option download
Automatically download
(The use of a internal
pattern)
■ EDID data (Model name = LG TV)
- RGB HD
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
01 16 01 03 68 A0 5A 78 0A EE 91 A3 54 4C 99 26
0F 50 54 A1 08 00 31 40 45 40 61 40 01 01 01 01
01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
36 00 B0 84 43 00 00 18 A0 0F 20 00 31 58 1C 20
28 80 14 00 B0 84 43 00 00 1E 00 00 00 FD 00 3A
3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 58
- South Centural America _2D_HD HDMI
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
0F 50 54 A1 08 00 31 40 45 40 61 40 01 01 01 01
01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
36 00 B0 84 43 00 00 18 A0 0F 20 00 31 58 1C 20
28 80 14 00 B0 84 43 00 00 1E 00 00 00 FD 00 3A
3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 3F
02 03 27 F1 4F 10 1F 84 13 05 14 03 02 12 20 22
15 11 16 01 26 15 07 50 09 57 07 67 03 0C 00 10
00 B8 2D E3 05 03 01 01 1D 00 72 51 D0 1E 20 6E
28 55 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D
40 58 2C 45 00 40 84 63 00 00 1E 01 1D 80 18 71
1C 16 20 58 2C 25 00 40 84 63 00 00 9E 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 D1
< For write EDID data, setting Jig and another instruments >
Only for training and service purposes
- 7 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
- South Centural America _2D_HD HDMI 2
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
0F 50 54 A1 08 00 31 40 45 40 61 40 01 01 01 01
01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
36 00 B0 84 43 00 00 18 A0 0F 20 00 31 58 1C 20
28 80 14 00 B0 84 43 00 00 1E 00 00 00 FD 00 3A
3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 3F
02 03 27 F1 4F 10 1F 84 13 05 14 03 02 12 20 22
15 11 16 01 26 15 07 50 09 57 07 67 03 0C 00 20
00 B8 2D E3 05 03 01 01 1D 00 72 51 D0 1E 20 6E
28 55 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D
40 58 2C 45 00 40 84 63 00 00 1E 01 1D 80 18 71
1C 16 20 58 2C 25 00 40 84 63 00 00 9E 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 C1
- South Centural America _2D_HD HDMI 3
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88
36 00 B0 84 43 00 00 18 A0 0F 20 00 31 58 1C 20
28 80 14 00 B0 84 43 00 00 1E 00 00 00 FD 00 3A
3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 3F
- Adjustment Color Temperature(White balance)
■ Using Instruments
● Color Analyzer: CA-210 (CH 10)
- Using LCD color temperature, Color Analyzer (CA-
210) must use CH 10, which Matrix compensated
(White, Red, Green, Blue compensation) with CS-
2100. See the Coordination bellowed one.
● Auto-adjustment Equipment (It needs when Auto-adjustment – It is availed communicate with RS-232C : Baud
rate: 115200)
● Video Signal Generator MSPG-925F 720p, 216Gray
(Model: 217, Pattern 78)
■ Connection Diagram (Auto Adjustment)
● Using Inner Pattern
● Using HDMI input
< connection Diagram for Adjustment White balance >
02 03 27 F1 4F 10 1F 84 13 05 14 03 02 12 20 22
15 11 16 01 26 15 07 50 09 57 07 67 03 0C 00 30
00 B8 2D E3 05 03 01 01 1D 00 72 51 D0 1E 20 6E
28 55 00 40 84 63 00 00 1E 02 3A 80 18 71 38 2D
40 58 2C 45 00 40 84 63 00 00 1E 01 1D 80 18 71
1C 16 20 58 2C 25 00 40 84 63 00 00 9E 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B1
- See Working Guide if you want more information about EDID
communication.
Only for training and service purposes
■ White Balance Adjustment
If you can’t adjust with inner pattern, then you can adjust
it using HDMI pattern. You can select option at “Ez-Adjust
Menu – 7. White Balance” there items “NONE, INNER,
HDMI”. It is normally setting at inner basically. If you can’t
adjust using inner pattern you can select HDMI item, and
you can adjust.
In manual Adjust case, if you press ADJ button of service
remocon, and enter “Ez-Adjust Menu – 7. White Balance”,
then automatically inner pattern operates. (In case of
“Inner” originally “Test-Pattern. On” will be selected in The
“Test-Pattern. On/Off”.
● Connect all cables and equipments like Pic.5)
● Set Baud Rate of RS-232C to 115200. It may set 115200
orignally.
● Connect RS-232C cable to set
● Connect HDMI cable to set
- 8 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
■ RS-232C Command (Commonly apply)
RS-232C COMMAND
[CMD ID DATA]
wb 00 00 White Balance adjustment start.
wb 00 10 Start of adjust gain
(Inner white pattern)
wb 00 1f End of gain adjust
wb 00 20 Start of offset adjust
(Inner white pattern)
wb 00 2f End of offset adjust
wb 00 ff End of White Balance adjust
(Inner pattern disappeared)
● “wb 00 00”: Start Auto-adjustment of white balance.
● “wb 00 10”: Start Gain Adjustment (Inner pattern)
● “jb 00 c0” :
● …
● “wb 00 1f”: End of Adjustment
* If it needs, offset adjustment (wb 00 20-start, wb 00 2f-
end)
● “wb 00 ff”: End of white balance adjustment (inner pattern
disappear)
■ Adjustment Mapping information
RS-232C
COMMAND
[CMD ID DATA]
Cool Mid Warm Cool Mid Warm
R Gain jg Ja jd 00 184 192 192 192
G Gain jh Jb je 00 187 183 159 192
B Gain ji Jc jf 00 192 161 95 192
R Cut 64 64 64 127
G Cut 64 64 64 127
B Cut 64 64 64 127
M
I
N
Meaning
CENTER
(DEFAULT)
M
● When Color temperature (White balance) Adjustment
(Automatically)
- Press “Power only key” of service remocon and operate
automatically adjustment.
- Set BaudRate to 115200.
● You must start “wb 00 00” and finish it “wb 00 ff”.
● If it needs, then adjustment “Offset”.
■ White Balance Adjustment (Manual adjustment)
● Test Equipment: CA-210
- Using PDP color temperature, Color Analyzer (CA-210)
must use CH 10, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the
Coordination bellowed one.
● Manual adjustment sequence is like bellowed one.
- Turn to “Ez-Adjust” mode with press ADJ button of service
remocon.
- Select “10.Test Pattern” with CH+/- button and press
enter. Then set will go on Heat-run mode. Over 30
minutes set let on Heat-run mode.
- Let CA-210 to zero calibration and must has gap more
10cm from center of PDP module when adjustment.
- Press “ADJ” button of service remocon and select
“7.White-Balance” in “Ez-Adjust” then press “►” button of
navigation key. (When press “►” button then set will go to
full white mode)
- Adjust at three mode (Cool, Medium, Warm)
- If “cool” mode
Let B-Gain to 192 and R, G, B-Cut to 64 and then control
R, G gain adjustment High Light adjustment.
- If “Medium” and “Warm” mode Let R-Gain to 192 and R,
G, B-Cut to 64 and then control G, B gain adjustment
High Light adjustment.
- All of the three mode
Let R-Gain to 192 and R, G, B-Cut to 64 and then control
G, B gain adjustment High Light adjustment.
- With volume button (+/-) you can adjust.
- After all adjustment finished, with Enter (■ key) turn to
Ez-Adjust mode. Then with ADJ button, exit from
adjustment mode
* Attachment: White Balance adjustment coordination and
color temperature.
● Using CS-1000 Equipment.
- COOL : T=11000K, ∆uv=0.000, x=0.276 y=0.283
- MEDIUM : T=9300K, ∆uv=0.000, x=0.285 y=0.293
- WARM : T=6500K, ∆uv=0.000, x=0.313 y=0.329
A
X
Only for training and service purposes
- 9 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
● When tester will measure on Cool condition, adjust W30 on
TV display menu.
● When tester will measure on medium condition, adjust 0 on
TV display menu.
● When tester will measure on warm condition, adjust W30 on
TV display menu.
● Using CA-210 Equipment. (10 CH)
- Contrast value: 216 Gray
Color
temperature
COOL CA-210 0.276 ± 0.002 0.283 ± 0.002
MEDIUM CA-210 0.285 ± 0.002 0.293 ± 0.002
WARM CA-210 0.313 ± 0.002 0.329 ± 0.002
- Brightness spec.
Item White average
Min 49 -20
Typ 60
Max +20
Unit cd/m² %
Remark - 100% Window White
Pattern
- 100IRE(255Gray)
- Picture: Vivid(Medium)
Test
Equipment
brightness
Color Coordination
x y
Brightness uniformity
- 85IRE(216Gray) 100%
Window White Pattern
- Picture: Vivid(Medium)
6. GND and ESD Testing
6.1. Prepare GND and ESD Testing.
■ Check the connection between set and power cord
6.2. Operate GND and ESD auto-test.
■ Fully connected (Between set and power cord) set enter the
Auto-test sequence.
■ Connect D-Jack AV jack test equipment.
■ Turn on Auto-controller(GWS103-4)
■ Start Auto GND test.
■ If its result is NG, then notice with buzzer.
■ If its result is OK, then automatically it turns to ESD Test.
■ Operate ESD test
■ If its result is NG, then notice with buzzer.
■ If its result is OK, then process next steps. Notice it with
Good lamp and STOPER Down.
6.3. Check Items.
■ Test Voltage
● GND: 1.5KV/min at 100mA
● Signal: 3KV/min at 100mA
■ Test time: just 1 second.
■ Test point
● GND test: Test between Power cord GND and Signal
cable metal GND.
● ESD test: Test between Power cord GND and Live and
neutral.
■ Leakage current: Set to 0.5mA(rms)
6.4. POWER PCB Ass’y Voltage adjustment
(Va, Vs voltage adjustment)
6.4.1. Test equipment : D.M.M 1EA
6.4.2. Connection Diagram for Measuring
: refer to g.1
<XPOWER4 50R4/T4 PSU>
5.3. Test of RS-232C control.
- Press In-Start button of Service Remocon then set the
“4.Baud Rate” to 115200. Then check RS-232C control and
5.4. Selection of Country option.
- Selection of country option is allowed only North American
model (Not allowed Korean model). It is selection of Country
about Rating and Time Zone.
■ Models: All models which PU11A Chassis (See the rst
page.)
■ Press “In-Start” button of Service Remocon, then enter the
“Option” Menu with “PIP CH-“ Button
■ Select one of these three (USA, CANADA, MEXICO) depends on its market using “Vol. +/-“button.
* Caution : Don’t push The INSTOP KEY after completing the
function inspection.
* Caution : Inspection only PAL M / NTSC
Only for training and service purposes
(g.1) PCB Assy Voltage adjustment
6.4.3. Adjustment method
6.4.3.1. Vs adjustment (refer g.1)
(1) Connect + terminal of D.M.M. to Vs pin of P811, connect
-terminal to GND pin of P811
(2) After turning VR901, voltage of D.M.M adjustment as same
as Vs voltage which on label of panel left/top ( deviation ;
±0.5V)
6.4.3.2. Va adjustment (refer g.1)
(1) After receiving 100% Full White Pattern, HEAT RUN.
(2) Connect + terminal of D.M.M. to Va pin of P811, connect
-terminal to GND pin of P811
(3) After turning VR502,voltage of D.M.M adjustment as same
as Va voltage which on label of panel left/top (deviation;
±0.5V)
- 10 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
7. Default Service option.
7.1. ADC-Set.
■ R-Gain adjustment Value (default 128)
■ G-Gain adjustment Value (default 128)
■ B-Gain adjustment Value (default 128)
■ R-Offset adjustment Value (default 128)
■ G-Offset adjustment Value (default 128)
■ B-Offset adjustment Value (default 128)
7.2. White balance. Value.
Center(Default)
COOL Mid Warm
R Gain 192 192 192
G Gain 192 192 192
B Gain 192 192 192
R Cut 64 64 64
G Cut 64 64 64
B Cut 64 64 64
7.3. Temperature Threshold
■ Threshold Down Low 20
■ Threshold Up Low 23
■ Threshold Down High 70
■ Threshold Up High 75
■ Select download le (epk le)
8. USB DOWNLOAD(*.epk le download)
■ Put the USB Stick to the USB socket
■ Press Menu key, and move OPTION
■ Press “FAV” Press 7 times
■ After download is nished, remove the USB stick.
■ Press “IN-START” key of ADJ remote control, check the
S/W version.
9. Tool option
50PA4500-SF
Tool option 1 36864
Tool option 2 22794
Tool option 3 3697
Tool option 4 51270
Tool option 5 10
Country code 03
Country Group BR
Country BR
Only for training and service purposes
- 11 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
BLOCK DIAGRAM
Only for training and service purposes
- 12 -
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
310
305
301
300
200
302
580
207
208
202
303
209
203
304
204
205
206
201
601
520
540
501
A12
A9
A10
LV1
400
Only for training and service purposes
240
- 13 -
590
910
120
900
A2
LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
Full SCART
Copyright © 2012 LG Electronics Inc. All rights reserved.
Only for training and service purposes
LGE Internal Use Only
EU
JK100
PSC008-02
SHIELD
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AV_DET
COM_GND
SYNC_IN
SYNC_OUT
SYNC_GND2
SYNC_GND1
RGB_IO
R_OUT
RGB_GND
R_GND
D2B_OUT
G_OUT
D2B_IN
G_GND
ID
B_OUT
AUDIO_L_IN
B_GND
AUDIO_GND
AUDIO_L_OUT
AUDIO_R_IN
AUDIO_R_OUT
+3.3V
R106
75
R108
75
R107
75
R104
10K
EU
R105
1K
EU
SC1_R+/COMP1_Pr+
SC1_G+/COMP1_Y+
SC1_B+/COMP1_Pb+
AV/SC1_DET
R115
470K
R116
470K
+5V
MULTI
R135
B
0
EU
R136
330
EU
REC_8
R139
2K
EU
Q103-*1
E
Q103
C
ISA1530AC1
EU
D112-*1
MMBD6100
C
R138
2K
EU
R137
2K
EU
C112
10uF
16V
EU
R140
2K
EU
E
C
MULTI
B
R141
220
EU
R142
390
READY
D112
C
A2
A1
C113
10uF
16V
EU
+3.3V_ST
B
MMBT3904(NXP)
EU
KDS184
A2
A1
R144
470
EU
C
B
Q104
E
EU
R143
180
EU
EU
MMBT3904(NXP)
Q107
C114
27pF
50V
EU
R145
6.8K
EU
C115
27pF
50V
EU
EU
R189
10K
E
C
SCART1_Lout
SCART1_MUTE
R146
18K
EU
R147
10K
EU
MMBT3904(NXP)
B
R149
15K
EU
R148
15K
EU
Q106
10uF
12K
R160
C116
16V
EU
EU
EU
E
C
R154
5.6K
R152
6.8K
EU
C117
0.1uF
16V
READY
DTV/MNT_VOUT
B
EU
MMBT3904(NXP)
Q105
EU
12K
R159
OUT1
IN1-
IN1+
VEE
EU
MMBT3906(NXP)
R129
0
EU
C106
100uF
16V
EU
R123
33
EU
R121
10K
EU
R124
10K
EU
R122
0
EU
R125
C109
27pF
50V
EU
C110
1000pF
50V
READY
R126
12K
EU
R127
12K
EU
C107
5600pF
50V
EU
C108
0
5600pF
EU
50V
EU
C111
220pF
50V
EU
R117
75
EU
R113
R118
5%
75
470K
EU
EU
1/1 6W
R119
75
EU
R114
R120
10K
2.7K
EU
EU
C102
1000pF
50V
EU
READY
C103
1000pF
EU
50V
READY
SC1_SOG_IN
AV/SC1_CVBS_IN
SC1_VOUT
SC1_FB
SC1_ID
AV/SC1_L_IN
AV/SC1_R_IN
Q100
MMBT3904(NXP)
EU
MMBT3904(NXP)
R134
100
1/4W
EU
Q101
C
E
EU
DTV_R_OUT
Q102
MMBT3904(NXP)
EU
L103
120-ohm
EU
EU
1K
R158
EU
E
1K
R157
B
C
IC101
AZ4580MTR-E1
1
2
3
4
R155
P_17V
PDP GP4 LM1
EAX64280503
SC_RE1
SC_RE2
EU
7.5K
R156
EU
3K
P_17V
VCC
8
OUT2
7
IN2-
6
IN2+
5
5.6K
R153
EU
SCART1_Rout
CI SLOT
BUF2_FE_TS_DATA[0-7]
/CI_CD1
CI_TS_DATA[4]
CI_TS_DATA[5]
CI_TS_DATA[6]
CI_TS_DATA[7]
CI_IORD
CI_IOWR
BUF2_FE_TS_SYN
BUF2_FE_TS_DATA[0]
BUF2_FE_TS_DATA[1]
BUF2_FE_TS_DATA[2]
BUF2_FE_TS_DATA[3]
BUF2_FE_TS_DATA[4]
BUF2_FE_TS_DATA[5]
BUF2_FE_TS_DATA[6]
BUF2_FE_TS_DATA[0-7]
BUF2_FE_TS_DATA[7]
PCM_RST
/PCM_WAIT
REG
CI_TS_CLK
CI_TS_VAL
CI_TS_SYNC
CI_TS_DATA[0]
CI_TS_DATA[1]
CI_TS_DATA[2]
CI_TS_DATA[3]
R150
10K
EU
+5V
/CI_CD2
+5V
R151
10K
R102
EU
100
EU
AR100 33
EU
R100
EU
R101
AR101 33
AR102 33
R103
100
EU
EU
33
+3.3V_CI
EU
R165
TC74LCX244FT
10K
AR105
EU
AR106 33
EU
AR107 33
IC100
1OE
1
20
EU
1A1
19
2
2Y4
18
3
1A2
17
4
2Y3
16
5
1A3
15
6
2Y2
14
7
1A4
13
8
2Y1
12
9
GND
10
11
+3.3V_CI
VCC
2OE
1Y1
2A4
1Y2
2A3
1Y3
2A2
1Y4
2A1
/PCM_OE
/PCM_WE
/PCM_IORD
/PCM_IOWR
PCM_A[12]
PCM_A[13]
PCM_A[14]
/PCM_REG
PCM_A[8]
PCM_A[9]CI_ADDR[9]
PCM_A[10]
PCM_A[11]
EU
C105
0.1uF
16V
CI_ADDR[0]
PCM_A[7]
CI_ADDR[1]
PCM_A[6]
CI_ADDR[2]
PCM_A[5]
CI_ADDR[3]
PCM_A[4]
BUF2_FE_TS_DATA[0-7]
AR108
33 EU
BUF2_FE_TS_DATA[0]
BUF2_FE_TS_DATA[1]
BUF2_FE_TS_DATA[2]
BUF2_FE_TS_DATA[3]
BUF2_FE_TS_DATA[4]
BUF2_FE_TS_DATA[5] BUF1_FE_TS_DATA[5]
BUF2_FE_TS_DATA[6]
BUF2_FE_TS_DATA[7]
BUF1_FE_TS_SYN
BUF1_FE_TS_VAL_ERR
BUF1_FE_TS_CLK
CI POWER ENABLE CONTROL
PCM_5V_CTL
BUF1_FE_TS_DATA[0]
BUF1_FE_TS_DATA[1]
BUF1_FE_TS_DATA[2]
BUF1_FE_TS_DATA[3]
AR109
33 EU
BUF1_FE_TS_DATA[4]
BUF1_FE_TS_DATA[6]
BUF1_FE_TS_DATA[7]
AR110
33
EU
+5V
R184
10K
READY
BUF2_FE_TS_SYN
BUF2_FE_TS_VAL_ERR
BUF2_FE_TS_CLK
5%
1/1 6W
B
R181
10K
EU
BUF1_FE_TS_DATA[0-7]
Q114
RSR025P03
EU
S
R187
10K
EU
R188
2K
EU
C
Q113
MMBT3904(NXP)
EU
E
BUF1_FE_TS_DATA[0-7]
L100
120-ohm
EU
D
C131
0.1uF
G
16V
READY
AO3407A
D
S
G
MULTI
Q114-*1
+5V_CI_ON
C104
0.1uF
16V
EU
R198
10K
READY
3.3V_CI
+3.3V
C136
0.1uF
16V
READY
L101
120-ohm
EU
+3.3V_CI
C137
0.1uF
16V
EU
CI_OE
+5V_CI_ON
C100
C101
22uF
0.1uF
10V
16V
EU
EU
JK102
10067972-000LF
EU
35
36
R111
10K
EU
R112
0
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
65
66
67
68
2
EU
READY
R109
10K
EU
33
33
EU
R110
0
EU
READY
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
R128 0
18
READY
19
20
21
22
23
24
25
2660
2761
2862
2963
3064
31
32
33
34
G1G2
1
69
AR103
33
EU
R130 33EU
1/16W
R131 33EU
5%
R132 100
AR104
33
EU
PCM_D[3]
PCM_D[4]
PCM_D[5]
PCM_D[6]
PCM_D[7]
EU
PCM_D[0]
PCM_D[1]
PCM_D[2]
CI_ADDR[10]
CI_ADDR[11]
CI_ADDR[9]
CI_ADDR[8]
CI_ADDR[13]
CI_ADDR[14]
CI_ADDR[12]
CI_ADDR[7]
CI_ADDR[6]
CI_ADDR[5]
CI_ADDR[4]
CI_ADDR[3]
CI_ADDR[2]
CI_ADDR[1]
CI_ADDR[0]
PCM_D[0-7]
R133
10K
EU
/PCM_CE
CI_OE
CI_WE
/PCM_IRQA
BUF2_FE_TS_VAL_ERR
BUF2_FE_TS_CLK
CI_ADDR[0-14]
PCM_D[0-7]
CI_WE
CI_IORD
CI_IOWR
CI_ADDR[12]
CI_ADDR[13]
CI_ADDR[14]
CI_ADDR[8]
CI_ADDR[10]
CI_ADDR[11]
CI_DET
PCM_A[0]
CI_ADDR[7]
PCM_A[1]
CI_ADDR[6]
PCM_A[2]
CI_ADDR[5]
PCM_A[3]
CI_ADDR[4]
REG
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
GP4_S7LR
SCART,CI Slot
2011-10-20
1
6
HDMI_1
Copyright © 2012 LG Electronics Inc. All rights reserved.
Only for training and service purposes
LGE Internal Use Only
SHIELD
20
JK200
HDMI_1
19
18
17
16
15
14
13
12
11
CK+
10
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
5V_HDMI_1
R200
1K
HDMI_1
R201
1.8K HDMI_1
HDMI_1
JK211
PPJ239-01
NON_EU
+5V
5V_DET_HDMI_1
MMBT3904(NXP)
R204
3.3K
JP201
HDMI_1
R281
R282
10K
10K
HDMI_1
JP2 02
[RD1]E-LUG
6H
[RD1]O-SPRING_2
5H
[RD1]CONTACT_2
4H
[WH1]O-SPRING
5G
[RD1]CONTACT_1
4F
[RD1]O-SPRING_1
5F
[RD1]E-LUG-S
7F
[BL1]O-SPRING
5E
[BL1]E-LUG-S
7E
Q200
HDMI_1
R207
33
HDMI_1
R208
33
HDMI_1
SPDIF
SIDE_HDMI_1
R230
3.3K
JP204
SIDE_HDMI_1
R231
33
SIDE_HDMI_1
R232
33
SIDE_HDMI_1
JP2 05
Q201
SIDE_HDMI_2SIDE_HDMI_1
DDC_SDA_2
DDC_SCL_2
CK-_HDMI2
CK+_HDMI2
D0-_HDMI2
D0+_HDMI2
D1-_HDMI2
D1+_HDMI2
D2-_HDMI2
D2+_HDMI2
SIDE_HDMI_2
BODY_SHIELD
HPD2
JK202
C
E
R203
10K
SIDE_HDMI_1
B
R237
10K
SIDE_HDMI_1
5V_HDMI_2
JK200-*1
YKF45-7058V
HDMI1_NON Screw
DATA2+
1
DATA2_SHIELD
B
R217
10K
HDMI_1
R202
10K
HDMI_1
DDC_SDA_1
DDC_SCL_1
HDMI_ARC
CEC_REMOTE
CK-_HDMI1
CK+_HDMI1
D0-_HDMI1
D0+_HDMI1
D1-_HDMI1
D1+_HDMI1
D2-_HDMI1
D2+_HDMI1
C
E
HPD1
DATA1_SHIELD
DATA0_SHIELD
2
DATA2-
3
DATA1+
4
5
DATA1-
6
DATA0+
7
8
DATA0-
9
CLK+
10
CLK_SHIELD
11
CLK-
12
CEC
13
NC
14
SCL
15
SDA
16
DDC/CEC_GND
17
+5V_POWER
18
HPD
19
20
SHIELD
BODY_SHIELD
20
19
18
17
16
15
14
13
12
11
10
JK201
SIDE_HDMI_1
CK+
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
+5V
R226
1K
SIDE_HDMI_1
R227
1.8K SIDE_HDMI_1
R286
10K
SIDE_HDMI_1
5V_DET_HDMI_2
MMBT3904(NXP)
R287
10K
SIDE_HDMI_1
COMPONENT2
JK208
PPJ234-02
EU
[GN]E-LUG
6A
[GN]O-SPRING
R299
0
5A
[GN]CONTACT
4A
[BL]E-LUG-S
7B
[BL]O-SPRING
5B
[RD]E-LUG-S
7C
[RD]O-SPRING_1
5C
[RD]CONTACT_1
4C
5D
[WH]O-SPRING
4E
[RD]CONTACT_2
5E
[RD]O-SPRING_2
6E
[RD]E-LUG
5V_HDMI_3
20
19
18
17
16
15
14
13
12
11
CK+
10
D0-
9
D0_GND
8
D0+
7
D1-
6
D1_GND
5
D1+
4
D2-
3
D2_GND
2
D2+
1
R240
1K
SIDE_HDMI_2
R241
1.8K SIDE_HDMI_2
R288
10K
SIDE_HDMI_2
R251
75
COMP2_Y+
R252
75
COMP2_Pb+
R253
75
COMP2_Pr+
R254
470K
R255
470K
+5V
5V_DET_HDMI_3
MMBT3904(NXP)
R289
10K
SIDE_HDMI_2
+3.3V
R256 10K
R25710K
SIDE_HDMI_2
R244
3.3K
JP207
SIDE_HDMI_2
R245
33 SIDE_HDMI_2
R246
33
JP2 08
R259
10K
R262
12K
R263
12K
C R209
Q202
E
SIDE_HDMI_2
R266
COMP2_DET
1K
R265
10K
AV2_DET
R267
1K
COMP2_L_IN
COMP2_R_IN
B
R250
10K
SIDE_HDMI_2
10K
SIDE_HDMI_2
HPD3
DDC_SDA_3
DDC_SCL_3
CEC_REMOTECEC_REMOTE
CK-_HDMI3
CK+_HDMI3
D0-_HDMI3
D0+_HDMI3
D1-_HDMI3
D1+_HDMI3
D2-_HDMI3
D2+_HDMI3
RS232C
JK203
SPG09-DB-009
1
2
3
4
5
For CEC
CEC_REMOTE
6
7
8
9
10
Q204
MMBT3904(NXP)
USA
NON_RGB
R274 0
NON_RGB
R275 0
R260
56K
READY
R261
0
READY
D222
READY
+5V_ST
C
E
PC_SER_DATA
PC_SER_CLK
+3.3V_ST
R276
R228
10K
USA
D224
MMBD301LT1G
30V
READY
S
G
+3.3V_ST
R278
10K
100
R277
100
R229
100K
USA
B
R233
100K
USA
R268
100
B D
R279
10K
TX
Q203
BSS83
READY
R283 0
R284 0
R269
27K
READY
MAX3232CDR
VCC
GND
DOU T1
RIN 1
ROU T1
DIN 1
DIN2
ROUT2
CEC_REMOTE_S7
S7_TXD
S7_RXD
PM_TXD
PM_RXD
IC206
16
15
14
13
12
11
10
9
SIDE USB
3AU04S-305-ZC-(LG)
C1+
1
0.1uF
V+
2
0.1uF
C1-
3
C2+
4
C2-
5
V-
6
DOUT2
7
RIN2
8
+3.3V_ST
C228
16V
C225
16V
C226
0.1uF
16V
C227
0.1uF
16V
FIX_POLE
10mm
R296
10K
READY
JK204
JST1223-001
Fiber Optic
4
JK209
USB DO WN STR EAM
C229
0.1uF
16V
5%
1/16W
GND
1
2
3
5
VCC
VINPUT
1234
+5V
C219
R285
0.1uF
100
16V
C220
10pF
50V
PEN_TOUCH
+5V_ST
Capacitors on VBUSA should be
placed as closd to connector as possible.
C212
0.1uF
16V
D225
AP2337SA-7
B140A
PEN_TOUCH
VIN
3
40V
C213
10uF
10V
USB1_OCD
SIDE_USB_DM
SIDE_USB_DP
1A SPEC
IC207
1
GND
ETHERNET
JK210
XRJV-01V-0-D12-080
1
1
2
2
3
3
4
4
5
ET_NET
5
6
6
7
7
8
8
9
9
VOUT
2
SPDIF_OUT
+2.5V
C200
0.1uF
16V
ET_NET
+3.3V
R264
10K
R258
33
MULTI
JK204-*1
2F01TC1-CLM97-4F
1
Fiber Optic
2
3
4
SHIELD
SWITCH ADDED
IC204
AP2191SG-13
NC
8
OUT_2
7
$0.11
OUT_1
6
FLG
5
D200
D204
5.6V
5.6V
ET_NET
ET_NET
GND
VCC
VIN
1
2
3
4
D205
5.6V
ET_NET
GND
IN_1
IN_2
EN
R273
0
ET_NET
R280
0
ET_NET
D206
5.6V
ET_NET
+3.3V
R270
10K
R271
33
+5V
+5V_ST
R243
R247
0
0
READY
USB1_CTL
JK210-*1
BS-R430051
TP
ET_NET_UDE
1
1
2
2
3
3
TN
4
4
5
RP
5
6
6
7
7
8
8
RN
9
9
R291
0
ET_NET
R290
0
ET_NET
[GN1]CONTACT
4D
[GN1]O-SPRING
5D
[GN1]E-LUG
6D
[RD2]E-LUG
6N
[RD2]O-SPRING_2
5N
[RD2]CONTACT
4N
[WH2]O-SPRING
5M
[RD2]O-SPRING_1
5L
[RD2]E-LUG-S
7L
[BL2]O-SPRING
5K
[BL2]E-LUG-S
7K
[GN2]CONTACT
4J
[GN2]O-SPRING
5J
[GN2]E-LUG
6J
R235
470K
NON_EU
R238
470K
NON_EU
NON_EU
R234
10K
NON_EU
R239
10K
R236
R242
12K
12K
NON_EU
R248
10K
NON_EU
NON_EU
+3.3V
NON_EU
R249
1K
COMP1_R_IN
COMP1_L_IN
SC1_R+/COMP1_Pr+
SC1_B+/COMP1_Pb+
COMP1_DET
SC1_G+/COMP1_Y+
RGB PC
JK205
SPG09-DB-010
6
1
7
2
8
3
9
4
10
5
16
GND
11
12
13
14
15
SHILED
RED_GND
GND_2
RED
GREEN_GND
DDC_DATA
GREEN
BLUE_GND
H_SYNC
BLUE
NC
V_SYNC
GND_1
SYNC_GND
DDC_CLOCK
DDC_GND
R297
R205
33
R206
33
+5V_ST
10K
C202
10pF
50V
R298
10K
R214
75
R215
75
R216
75
R212
10
R211
10
C203
10pF
50V
DSUB_R+
RGB_DDC_SDA
DSUB_G+
DSUB_HSYNC
DSUB_B+
DSUB_VSYNC
RGB_DDC_SCL
PC_SER_DATA
PC_SER_CLK
+3.3V
R224
10K
R225
PC AUDIO
JK206
PEJ027-04
1K
DSUB_DET
E_SPRING
3
T_TERMINAL1
6A
B_TERMINAL1
7A
R_SPRING
4
T_SPRING
5
B_TERMINAL2
7B
T_TERMINAL2
6B
R218
470K
R219
470K
R220
10K
1/16W
5%
R221
10K
R222
12K
R223
12K
PC_R_IN
PC_L_IN
JK207
PEJ027-04
USA
E_SPRING
3
T_TERMINAL1
6A
B_TERMINAL1
7A
R_SPRING
4
T_SPRING
5
B_TERMINAL2
7B
T_TERMINAL2
6B
R21 0
10
USA
R213
0
NON_USA
IR
TX
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
GP4_S7LR
JACK INTERFACE
2011-10-20
2
6
Loading...