LG 49LH604V, 55LH604V Owner’s Manual [tr]
Please read this manual carefully before operating your set and
retain it for future reference.
*MFL69311721*
www.lg.com
P/NO : MFL69311721(1603-REV00)
Printed in Korea
Safety and Reference
OWNER’S MANUAL
LED TV*
* LG LED TV applies LCD screen with LED
backlights.
2
ENGLISH
Safety instructions
Please read these safety precautions
carefully before using the product.
WARNING
Do not place the TV and/or remote control in
the following environments:
tA location exposed to direct sunlight
tAn area with high humidity such as a
bathroom
tNear any heat source such as stoves and
other devices that produce heat
tNear kitchen counters or humidiers where
they can easily be exposed to steam or oil
tAn area exposed to rain or wind
tNear containers of water such as vases
Otherwise, this may result in re, electric
shock, malfunction or product deformation.
Do not place the product where it might be
exposed to dust. This may cause a re hazard.
Mains Plug is the TV connecting/disconnecting
device to AC mains electric supply. This plug
must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or
wipe dust o. You may be electrocuted due to
excess moisture.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin.
(Except for devices which are not grounded
on earth.) Otherwise possibility you may be
electrocuted or injured.
Insert power cable plug completely into wall
socket otherwise if not secured completely into
socket, re ignition may break out.
Ensure the power cord does not come into
contact with hot objects such as a heater. This
may cause a re or an electric shock hazard.
Do not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in re or electric
shock.
3
ENGLISH
Bend antenna cable between inside and
outside building to prevent rain from owing
in. This may cause water damaged inside the
Product and could give an electric shock.
When mounting TV onto wall make sure to
neatly install and isolate cabling from rear of
TV as to not create possibility of electric shock /
re hazard.
Do not plug too many electrical devices into a
single multiple electrical outlet. Otherwise, this
may result in re due to over-heating.
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this
may result in injury or damage to the product.
Keep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause
suocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the
TV.
Otherwise, the TV may fall over, which may
cause serious injury.
Dispose of used batteries carefully to ensure
that a small child does not consume them.
Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not touch
the power cable right after plugging into the
wall input terminal. You may be electrocuted.
(Depending on model)
Do not put or store inammable substances
near the product. There is a danger of
combustion/explosion or re due to careless
handling of the inammable substances.
4
ENGLISH
Do not drop metallic objects such as coins,
hair pins, chopsticks or wire into the product,
or inammable objects such as paper and
matches. Children must pay particular
attention. Electrical shock, re or injury can
occur. If a foreign object is dropped into the
product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub
with an inammable substance (thinner or
benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects
to fall into the unit, and do not drop anything
onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a
thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there
is leakage of gas, open the windows and
ventilate. It may cause a re or a burn by a
spark.
Do not disassemble, repair or modify the
product at your own discretion. Fire or electric
shock accident can occur.
Contact the service centre for check, calibration
or repair.
If any of the following occur, unplug the
product immediately and contact your local
service centre.
tThe product has been impacted by shock
tThe product has been damaged
tForeign objects have entered the product
tThe product produced smoke or a strange
smell
This may result in re or electric shock.
Unplug the TV from AC mains wall socket if you
do not intend to use the TV for a long period of
time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric
leakage/shock/re.
5
ENGLISH
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could
be exposed to oil or oil mist. This may damage
the product and cause it to fall.
If water enters or comes into contact with TV,
AC adapter or power cord please disconnect
the power cord and contact service centre
immediately. Otherwise, this may result in
electric shock or re.
Only use an authorized AC adapter and power
cord approved by LG Electronics. Otherwise, this
may result in re, electric shock, malfunction or
product deformation.
Never Disassemble the AC adapter or power
cord. This may result in re or electric shock.
Be careful in handling the adapter to prevent
any external shocks to it. An external shock may
cause damage to the adapter.
Make sure the power cord is connected securely
to the power plug on the TV. (Depending on
model)
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an
outside antenna and power lines to keep the
former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as
unstable shelves or inclined surfaces. Also avoid
places where there is vibration or where the
product cannot be fully supported. Otherwise,
the product may fall or ip over, which may
cause injury or damage to the product.
6
ENGLISH
If you install the TV on a stand, you need to
take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.
If you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), x it
carefully so as not to drop.
Only use the attachments / accessories specied
by the manufacturer.
When installing the antenna, consult with a
qualied service technician. If not installed by
a qualied technician, this may create a re
hazard or an electric shock hazard.
We recommend that you maintain a distance
of at least 2 to 7 times the diagonal screen size
when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This could
cause damage to the remote control.
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and
leak.
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight, open replace and electric heaters.
Do not place non-rechargeable batteries in
charging device.
Make sure there are no objects between the
remote control and its sensor.
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
uorescent lighting. If this occurs turn o
lighting or darken viewing area.
When connecting external devices such as
video game consoles, make sure the connecting
cables are long enough. Otherwise, the product
may fall over, which may cause injury or
damage the product.
7
ENGLISH
Do not turn the product On/O by pluggingin or unplugging the power plug to the wall
outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an
electric shock.
Please follow the installation instructions
below to prevent the product from overheating.
tThe distance between the product and the
wall should be more than 10cm.
tDo not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
tDo not install the product on a carpet or
cushion.
tMake sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings
when watching the TV for long periods as the
ventilation openings may become hot. This
does not aect the operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on the power plug pins
or outlet. This may cause a re hazard.
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a
hand or sharp object such as nail, pencil or pen,
or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your
nger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
8
ENGLISH
When cleaning the product and its components,
unplug the power rst and wipe it with a soft
cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with
water or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives or
wax, benzene, alcohol etc., which can damage
the product and its panel. Otherwise, this may
result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn o this unit by SWITCH.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power
cord from the power board, as this could be
hazardous.
When moving the product, make sure you turn
the power o rst. Then, unplug the power
cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged,
which may create a re hazard or cause electric
shock.
When moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
If the product feels cold to the touch, there may
be a small “icker” when it is turned on. This is
normal, there is nothing wrong with product.
This panel is an advanced product that contains
millions of pixels. You may see tiny black dots
and/or brightly coloured dots (red, blue or
green) at a size of 1ppm on the panel. This does
not indicate a malfunction and does not aect
the performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
9
ENGLISH
You may nd dierent brightness and color
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
Displaying a still image for a prolonged period
of time may cause image sticking. Avoid
displaying a xed image on the TV screen for a
long period of time.
Generated Sound
“Cracking” noise: A cracking noise that
occurs when watching or turning o the TV
is generated by plastic thermal contraction
due to tempera-ture and humidity. This
noise is common for products where thermal
deformation is required. Electrical circuit
humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit,
which supplies a large amount of current to
operate a product. It varies depending on the
product.
This generated sound does not aect the
performance and reliability of the product.
Do not use high voltage electrical goods near
the TV (e.g. electric mosquito-swatter). This
may result in product malfunction.
Preparing
NOTE
tIf the TV is turned on for the rst time
after it was shipped from the factory,
initialization of the TV may take a few
minutes. (Depending on model)
tImage shown may dier from your TV.
tYour TV’s OSD (On Screen Display) may dier
slightly from that shown in this manual.
tThe available menus and options may dier
from the input source or product model that
you are using.
tNew features may be added to this TV in the
future.
tThe items supplied with your product may
vary depending on the model.
tProduct specications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
tFor an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the
USB cable or USB memory stick does not t
into your TV’s USB port.
A
B
A
B
*A
<
10 mm
*B
<
18 mm
tUse a certied cable with the HDMI logo
attached.
10
ENGLISH
tIf you do not use a certied HDMI cable, the
screen may not display or a connection error
may occur. (Recommended HDMI Cable
Types)
- High-Speed HDMI®/TM cable (3 m or less)
- High-Speed HDMI
®/TM
cable with Ethernet
(3 m or less)
tHow to use the ferrite core (Depending on
model)
- Use the ferrite core to reduce the
electromagnetic interference in the power
cord. Wind the power cord on the ferrite
core once.
[Wall side]
[TV side]
10 cm (+ / -2 cm)
tThis Smart TV is for VOD watching
service, some smart functions may not be
supported including web browser. (Only
LH57**)
CAUTION
tDo not use any unapproved items to ensure
the safety and product life span.
tAny damage or injuries caused by using
unapproved items are not covered by the
warranty.
tSome models have a thin lm attached on
to the screen and this must not be removed.
tWhen attaching the stand to the TV
set, place the screen facing down on a
cushioned table or at surface to protect
the screen from scratches.
tMake sure that the screws are fastened
completely. (If they are not fastened
securely enough, the TV may tilt forward
after being installed.) Do not use too
much force and over tighten the screws;
otherwise screw may be damaged and not
tighten correctly.
Lifting and moving
the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
tIt is recommended to move the TV in
the box or packing material that the TV
originally came in.
tBefore moving or lifting the TV, disconnect
the power cord and all cables.
tWhen holding the TV, the screen should
face away from you to avoid damage.
11
ENGLISH
tHold the top and bottom of the TV
frame rmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
tWhen transporting a large TV, there should
be at least 2 people.
tWhen transporting the TV by hand, hold the
TV as shown in the following illustration.
tWhen transporting the TV, do not expose
the TV to jolts or excessive vibration.
tWhen transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
tDo not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
tWhen handling the TV, be careful not to
damage the protruding buttons.
CAUTION
tAvoid touching the screen at all times, as
this may result in damage to the screen.
tDo not move the TV by holding the cable
holders, as the cable holders may break,
and injuries and damage to the TV may
occur.
Using the button
(Depending on model)
You can simply operate the TV functions,
pressing or moving the button.
NOTE
tLH57/59 series does not have a Joystick
functions but has only a power On/O
button.
Joystick Button
Dome Button
or
Basic functions
Power On (Press)
Power O (Press and
hold)
1
Volume Control
Programmes Control
1 All running apps will close, and any recording
in progress will stop.
12
ENGLISH
Adjusting the menu
When the TV is turned on, press the button
one time. You can adjust the Menu items
pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns
to TV viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a
table
1 Lift and tilt the TV into its upright position on
a table.
tLeave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
tDo not place the TV near or on sources
of heat, as this may result in re or other
damage.
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
tIf there are bolts inserted at the eye-bolts
position, remove the bolts rst.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the at surface.
CAUTION
tMake sure that children do not climb on or
hang on the TV.
NOTE
tUse a platform or cabinet that is strong and
large enough to support the TV securely.
tBrackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
13
ENGLISH
Mounting on a wall
Attach an optional wall mount bracket at the
rear of the TV carefully and install the wall
mount bracket on a solid wall perpendicular
to the oor. When you attach the TV to other
building materials, please contact qualied
personnel. LG recommends that wall mounting
be performed by a qualied professional
installer. We recommend the use of LG’s wall
mount bracket. LG’s wall mount bracket is
easy to move with cables connected. When
you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is
adequately secured to the wall with enough
space to allow connectivity to external devices.
It is advised to connect all the cables before
installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are
described in the following table.
Separate purchase(Wall
mounting bracket)
Model
32/43LH57**
32/43LH59**
32/40/43LH60**
32/43LH61**
49LH57**
49LH59**
49/55LH60**
49/55LH61**
VESA (A x B)
(mm)
200 x 200 300 x 300
Standard
screw
M6 M6
Number of
screws
4 4
Wall mount
bracket
LSW240B
MSW240
LSW350B
MSW240
Model
55LH57**
55LH59**
VESA (A x B)
(mm)
400 x 400
Standard
screw
M6
Number of
screws
4
Wall mount
bracket
LSW440B
MSW240
A
B
14
ENGLISH
CAUTION
tRemove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
NOTE
tWhen installing the wall mounting bracket,
use the adhesive label or protective cover
provided. The adhesive label or protective
cover will protect the opening from
accumulating dust and dirt. (Only when the
label or cover is provided)
Provided item
Adhesive label
Provided item
Adhesive label
Provided item
Protective cover
tWhen installing the wall mounting bracket,
it is recommended to cover the stand hole
using tape, in order to prevent the inux of
dust and insects. (Depending on model)
Stand hole
tWhen attaching a wall mounting bracket
to the TV, insert the wall mount spacers
into the TV wall mount holes to adjust the
vertical angle of the TV. (Only when the
item of the following form is provided)
Provided
item
Wall mount
spacer
tDepending on the shape of the stand, use
a at tool to remove the stand cover as
illustrated below. (e.g., a at screwdriver)
(Only when the item of the following form is
provided)
Flat tool
15
ENGLISH
Connections
(notications)
Connect various external devices to the TV
and switch input modes to select an external
device. For more information of external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
tThe external device connection may dier
from the model.
tConnect external devices to the TV regardless
of the order of the TV port.
tIf you record a TV program on a DVD recorder
or VCR, make sure to connect the TV signal
input cable to the TV through a DVD recorder
or VCR. For more information of recording,
refer to the manual provided with the
connected device.
tRefer to the external equipment’s manual for
operating instructions.
tIf you connect a gaming device to the TV, use
the cable supplied with the gaming device.
tIn PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change the
PC output to another resolution, change the
refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu
until the picture is clear.
tIn PC mode, some resolution settings may not
work properly depending on the graphics card.
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
tUse a signal splitter to use more than 2 TVs.
tIf the image quality is poor, install a signal
amplier properly to improve the image
quality.
tIf the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
tAn antenna cable and converter are not
supplied.
tSupported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV
mode.
tCheck if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
tIf the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
16
ENGLISH
USB connection
Some USB Hubs may not work. If a USB device
connected through a USB Hub is not detected,
connect it directly to the USB port on the TV.
Other connections
Connect your TV to external devices. For the
best picture and audio quality, connect the
external device and the TV with the HDMI cable.
Some separate cable is not provided.
NOTE
tSupported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192
kHz)
(Depending on model)
Remote control
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
To replace batteries, open the battery cover,
replace batteries (1.5 V AAA) matching
the
and ends to the label inside the
compartment, and close the battery cover. To
remove the batteries, perform the installation
actions in reverse.
Make sure to point the remote control toward
the remote control sensor on the TV.
A
B
1
2 3 4
5
6
7
A
(POWER) Turns the TV on or o.
Selects Radio, TV and DTV
programme.
1
, 4 (INPUT) Changes the input
source. (Depending on model)
1
, 4 Recalls your preferred
subtitle in digital mode. (Depending on
model)
2
(Q. Settings) Accesses the Quick
Settings. (Depending on model)
2
By pressing the AD button, audio
descriptions function will be enabled.
(Depending on model)
3
Views the information of the
current programme and screen. (Depending
on model)
3
By zooming in on the
selected area, you can view it in full screen.
(Depending on model)
3
Resizes an image. (Depending
on model)
17
ENGLISH
B
Number buttons Enters numbers.
Alphabet buttons Enters letters. (Depending
on model)
Accesses the saved programmes list.
(Space) Opens an empty space on the
screen keyboard. (Depending on model)
5
, 7 Shows programme guide.
(Depending on model)
5
Returns to the previously viewed
programme. (Depending on model)
Adjusts the volume level.
6
Views the information of the
current programme and screen. (Depending
on model)
6
, 7 (SEARCH) Search for content
such as TV programmes, movies and other
videos, or perform a web search by entering
text in the search bar. (Depending on model)
6
Accesses your favourite programme
list. (Depending on model)
(MUTE) Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next
screen.
C
D
8 9
10
11
12
14 15
16
13
C
8
Shows the previous history.
(Depending on model)
8
, 9 , 10 , 11 , 12 , 13 Teletext
buttons ( ) These buttons are
used for teletext. (Depending on model)
(HOME) Accesses the Home menu.
9
Shows the list of
Recommended, Programmes, Search and
Recorded. (Depending on model)
10
, 12 Returns to the previous level.
(Depending on model)
10
(Q. Settings) Accesses the Quick
Settings. (Depending on model)
11
, 13 Clears on-screen displays and
returns to TV viewing. (Depending on model)
11
Accesses the Quick menus.
(Depending on model)
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
Selects menus or options and conrms
your input.
Loading...