LG 42LM660T, 42LM660T-ZA, 42LM669S, 42LM669T, 42LM669T-ZC Service Manual

Printed in KoreaP/NO : MFL67360917 (1204-REV00)

CHASSIS : LD22E

MODEL: 42LM660S/660T/669S/669T

MODEL: 42LM660S/660T-ZA 42LM669S/669T-ZC

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

LED LCD TV

SERVICE MANUAL

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

Internal Use Only

- 2 -

Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS .................................................................... 4

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION .............................................................. 10

SCREW ASSEMBLY WORKING GUIDE .............................................. 18

BLOCK DIAGRAM .................................................................................. 19

EXPLODED VIEW .................................................................................. 20

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

- 3 -

Only for training and service purposes

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of th e cir cuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exp ose d metallic par t. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

IMPORTANT SAFETY NOTICE

SAFETY PRECAUTIONS

- 4 -

Only for training and service purposes

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board mod-

ule or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specied otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a ammable mixture. Unless specied otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this service manual. CAUTION: Do not connect the test xture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some eld-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classied as “anti-static” can generate electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted oor can generate static electricity sufcient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder ows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 5 -

Only for training and service purposes

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

- 6 -

Only for training and service purposes

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

.

1. Application range

This specification is applied to the LCD TV used LD22E chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed

ea ch drawing and s pe cificatio n b y p art number in accordance with BOM.

5) The receiver must be operated for about 20 minutes prior to

the adjustment.

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

- Safety : CE, IEC specification

- EMC : CE, IEC

- Wireless : Wireless HD Specification (Option)

4. Model General Specification

No. Item Specication Remarks

1 Market EU(PAL Market-36Countries)

DTV & Analog (Total 37 countries) DTV (MPEG2/4, DVB-T) : 30 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus

DTV (MPEG2/4, DVB-T2) : 7 countries

UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan, Ireland

DTV (MPEG2/4, DVB-C) : 37 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan

DTV (MPEG2/4,DVB-S) : 30 countries

Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus

Supported satellite : 22 satellites

HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102, ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EUTELSAT-W3A, EUROBIRD 9°, EUTELSAT-W2A, HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA 3°/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSATW7, HELLASSAT 2, EXPRESS AM1, TURKSAT 2°/3°, INTERSAT10

- 7 -

Only for training and service purposes

No. Item Specication Remarks

2 Broadcasting system

1) PAL-BG

2) PAL-DK

3) PAL-I/I’

4) SECAM L/L’, DK, BG, I

5) DVB-T

6) DVB-C

7) DVB-T2

8) DVB-S

DVB-S: Satellite

3 Receiving system

Analog : Upper Heterodyne Digital : COFDM, QAM

► DVB-T

- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32

- Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

► DVB-T2

- Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,

- Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

► DVB-C

- Symbolrate :

4.0Msymbols/s to 7.2Msymbols/s

- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

► DVB-S/S2

- symbolrate DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s DVB-S (QPSK) : 2 ~ 45Msymbol/s

- viterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10

4 Scart Gender Jack (1EA) PAL, SECAM

Scart jack is Full scart and support MNT/DTV-OUT (not support DTV Auto AV)

5 Video Input RCA(1EA) PAL, SECAM, NTSC

4 System : PAL, SECAM, NTSC, PAL60 AV gender jack 1EA

6 Head phone out

Antenna, AV1, AV2, Component, RGB, HDMI1, HDMI2, HDMI3, HDMI4, USB1, USB2, USB3

7 Component Input (1EA)

Y/Cb/Cr Y/Pb/Pr

Component Gender 1EA

8 RGB Input RGB-PC Analog(D-SUB 15PIN)

9 HDMI Input (4EA)

HDMI1-DTV HDMI2-DTV HDMI3-DTV HDMI4-DTV

HDMI4 : PC support(HDMI version 1.3) Support HDCP

10 Audio Input (3EA)

RGB/DVI Audio Component AV

L/R Input

11 SPDIF out (1EA) SPDIF out

12 USB (3EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD

13 Ethernet Connect(1EA) Ethernet Connect

- 8 -

Only for training and service purposes

5. Component Video Input (Y,

Cb/Pb, Cr/Pr)

6. RGB input (PC)

No. Resolution H-freq(kHz) V-freq(Hz) Porposed

1 720×480 15.73 60.00 SDTV, DVD 480i

2 720×480 15.63 59.94 SDTV, DVD 480i

3 720×480 31.47 59.94 480p

4 720×480 31.50 60.00 480p

5 720×576 15.625 50.00 SDTV, DVD 625 Line

6 720×576 31.25 50.00 HDTV 576p

7 1280×720 45.00 50.00 HDTV 720p

8 1280×720 44.96 59.94 HDTV 720p

9 1280×720 45.00 60.00 HDTV 720p

10 1920×1080 31.25 50.00 HDTV 1080i

11 1920×1080 33.75 60.00 HDTV 1080i

12 1920×1080 33.72 59.94 HDTV 1080i

13 1920×1080 56.250 50 HDTV 1080p

14 1920×1080 67.5 60 HDTV 1080p

No. Resolution H-freq(kHz) V-freq.(Hz) Proposed

1 640 x 350 @70Hz 31.468 70.09 EGA

2 720 x 400 @70Hz 31.469 70.08 DOS

3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)

4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)

5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)

6 1152 x 864 @60Hz 54.348 60.053 VESA

7 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)

8 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking))

- 9 -

Only for training and service purposes

7. HDMI Input

7.1. DTV mode

No. Resolution H-freq(kHz) V-freq.(kHz) Proposed

1. 640*480 31.469 / 31.5 59.94/60 SDTV 480P

2. 720*480 31.469 / 31.5 59.94 / 60 SDTV 480P

3. 720*576 31.25 50 SDTV 576P

4. 720*576 15.625 50 SDTV 576I

5. 1280*720 37.500 50 HDTV 720P

6. 1280*720 44.96 / 45 59.94 / 60 HDTV 720P

7. 1920*1080 33.72 / 33.75 59.94 / 60 HDTV 1080I

8. 1920*1080 28.125 50.00 HDTV 1080I

9. 1920*1080 26.97 / 27 23.97 / 24 HDTV 1080P

10. 1920*1080 25 HDTV 1080P

11. 1920*1080 33.716 / 33.75 29.976 / 30.00 HDTV 1080P

12. 1920*1080 56.250 50 HDTV 1080P

13. 1920*1080 67.43 / 67.5 59.94 / 60 HDTV 1080P

No. Resolution H-freq(kHz) V-freq.(Hz) Proposed

1 640 x 350 @70Hz 31.468 70.09 EGA

2 720 x 400 @70Hz 31.469 70.08 DOS

3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)

4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)

5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)

6 1152 x 864 @60Hz 54.348 60.053 VESA

7 1280 x 1024 @60Hz 63.981 60.020 VESA(SXGA)

8 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)

9 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking))

7.2. PC mode

- 10 -

Only for training and service purposes

ADJUSTMENT INSTRUCTION

1. Application Range

This specification sheet is applied to all of the LED LCD TV with LD22E chassis.

2. Designation

(1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation

transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of

25 °C ± 5 °C of temperature and 65 % ± 10 % of relative

humidity if there is no specific designation. (4) The input voltage of the receiver must keep AC 100-240

V~, 50/60 Hz. (5) The receiver must be operated for about 5 minutes prior to

the adjustment when module is in the circumstance of over

15.

In case of keeping module is in the circumstance of 0 °C, it should be placed in the circumstance of above 15 °C for 2 hours.

In case of keeping module is in the circumstance of below

-20 °C, it should be placed in the circumstance of above 15 °C for 3 hours.

[Caution] When still image is displayed for a period of 20 minutes or longer (Especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.

3. Automatic Adjustment

3.1. ADC Adjustment

3.1.1. Overview

ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation.

3.1.2. Equipment & Condition

(1) USB to RS-232C Jig (2) MSPG-92 5 Series Pattern Generat or(MSPG-925FA,

pattern - 65)

- Resolution : 1080P Comp1 1920*1080 RGB

- Pattern : Horizontal 100% Color Bar Pattern

- Pattern level : 0.7 ± 0.1 Vp-p

- Image

3.1.3. Adjustment

(1) Adjustment method

▪ Don’t need to adjust ADC because there is data in OTP

and adjusted initially.

▪ Check ADC adjustment

1) Press In start key on the Adj. Remote Control, then Adjust ADC(OTP) status is displayed on “1.Adjustment check ”. Sele ct “2.A DC Data ”, then AD C data is displayed.

2) Press Adj. key on the Adjustmetn Remote Control, and select “9.ADC Calibration”. Set up the ADC Type to OTP, then Select [Start] button by pressing Enter key, Component and RGB are Writed and display Success or NG.

(2) Adj. protocol

Ref.) ADC Adj. RS232C Protocol_Ver1.0

(3) Adj. order

- aa 00 00 [Enter ADC adj. mode]

- xb 00 04 [Change input source to Component1 (480i& 1080p)]

- ad 00 10 [Adjust 480i&1080p Comp1]

- xb 00 06 [Change input source to RGB(1024*768)]

- ad 00 10 [Adjust 1920*1080 RGB]

- ad 00 90 End adj.

Protocol Command Set ACK

Enter adj. mode aa 00 00 a 00 OK00x

Source change

xb 00 04 b 00 OK04x (Adjust 480i, 1080p Comp1 )

xb 00 06 b 00 OK06x (Adjust 1920*1080 RGB)

Begin adj. ad 00 10

Return adj. result

OKx (Case of Success) NGx (Case of Fail)

Read adj. data

(main) ad 00 20

(main) 000000000000000000000000007c007b006dx

(sub )

(Sub) 000000070000000000000000007c00830077x

ad 00 21

Conrm adj. ad 00 99

NG 03 00x (Fail) NG 03 01x (Fail) NG 03 02x (Fail) OK 03 03x (Success)

End adj. aa 00 90 a 00 OK90x

- 11 -

Only for training and service purposes

3.2. MAC address D/L, CI+ key D/L, Widevine key D/L, ESN D/L

Connect: USB port Communication Prot connection ▪ Com 1,2,3,4 and 115200(Baudrate) Mode check: Online Only ▪ check the test process: DETECT -> MAC -> CI -> Widevine

-> ESN ▪. Play: START ▪. Result: Ready, Test, OK or NG ▪. Printer Out (MAC Address Label)

3.3. LAN

3.3.1. Equipment & Condition

▪ Each other connection to LAN Port of IP Hub and Jig

3.3.2. LAN inspection solution

▪ LAN Port connection with PCB ▪ Network setting at MENU Mode of TV ▪ Setting automatic IP ▪ Setting state confirmation

→ If automatic setting is finished, you confirm IP and MAC

Address.

3.3.3. WIDEVINE key Inspection

- Confirm key input data at the "IN START" MENU Mode.

3.4. LAN PORT INSPECTION(PING TEST)

Connect SET → LAN port == PC → LAN Port

3.4.1. Equipment setting

(1) Play the LAN Port Test PROGRAM. (2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

3.4.2. LAN PORT inspection(PING TEST)

(1) Play the LAN Port Test Program. (2) Connect each other LAN Port Jack. (3) Play Test (F9) button and confirm OK Message. (4) Remove LAN cable.

Play: Start

G

SET PC

- 12 -

Only for training and service purposes

3.5. Model name & Serial number Download

3.5.1. Model name & Serial number D/L

▪ Press "Power on" key of service remote control.

(Baud rate : 115200 bps)

▪ Connect RS232 Signal Cable to RS-232 Jack. ▪ Write Serial number by use RS-232. ▪ Must check the serial number at Instart menu.

3.5.2. Method & notice

(1) Serial number D/L is using of scan equipment. (2) Setting of scan equipment operated by Manufacturing

Technology Group.

(3) Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatory by D-book 4.0

* Manual Download (Model Name and Serial Number)

If the TV set is downloaded by OTA or service man, sometimes model name or serial number is initialized.(Not always) It is impossible to download by bar code scan, so It need Manual download.

1) Press the "Instart" key of Adjustment remote control.

2) Go to the menu "5.Model Number D/L" like below photo.

3) Input the Factory model name(ex 47LM760S-ZB-A) or Serial number like photo.

4) Check the model name Instart menu. → Factory name displayed. (ex 47LM760S-ZB)

5) Check the Diagnost ics.(DTV country only) → Buyer model displayed. (ex 47LM760S-ZB)

3.6. CI+ Key checking method

- Check the Section 3.2 Check whether the key was downloaded or not at ‘In Start’ menu. (Refer to below).

=> Check the Download to CI+ Key value in LGset.

3.6.1. Check the method of CI+ Key value

(1) Check the method on Instart menu (2) Check the method of RS232C Command

1) Into the main ass’y mode(RS232: aa 00 00)

2) Check the key download for transmitted command (RS232: ci 00 10)

3) Result value

- Normally status for download : OKx

- Abnormally status for download : NGx

3.6.2. Check the method of CI+ key value(RS232)

1) Into the main ass’y mode(RS232: aa 00 00)

2) Check the mothed of CI+ key by command (RS232: ci 00 20)

3) Result value i 01 OK 1d1852d21c1ed5dcx

3.7. WIFI MAC ADDRESS CHECK

(1) Using RS232

(2) Check the menu on in-start.

CMD 1 CMD 2 Data 0

A A 0 0

CMD 1 CMD 2 Data 0

C I 1 0

CMD 1 CMD 2 Data 0

A A 0 0

CMD 1 CMD 2 Data 0

C I 2 0

CI+ Key Value

H-freq(kHz) V-freq.(Hz)

Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]

- 13 -

Only for training and service purposes

4. Manual Adjustment

* ADC adjustment is not needed because of OTP(Auto ADC

adjustment)

4.1 EDID(The Extended Display Identification Data)/DDC(Display Data Channel) download

4.1.1. Overview

It is a VESA regulation. A PC or a MNT will display an optimal resolution through information sharing without any necessity of user input. It is a realization of "Plug and Play".

4.1.2. Equipment

- Since embedded EDID data is used, EDID download JIG, HDMI cable and D-sub cable are not need.

- Adjustment remote control

4.1.3. Download method

(1) Press "ADJ" key on the Adjustment remote control then

select "10.EDID D/L", By pressing "Enter" key, enter EDID D/L menu.

(2) Select "Start" button by pressing "Enter" key, HDMI1/

HDMI2/ HDMI3/ HDMI4/ RGB are writing and display OK or NG.

4.1.4. EDID DATA

(1) 3D EDID DATA

▪ Reference

- HDMI1 ~ HDMI4 / RGB

- In the data of EDID, bellows may be different by S/W or Input mode.

ⓐ. Product ID

ⓑ. Serial No: Controlled on production line. ⓒ. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'

Year : '2012' -> '16' fix

ⓓ. Model Name(Hex): LGTV

ⓔ. Checksum: Changeable by total EDID data.

ⓕ. Vendor Specific(HDMI)

1) Deep color (module 10bit)

2) None deep color (module 8bit)

ⓖ Colorimetry Data Block(HDMI)

- The Model supporting XvYcc(LM7600)

For Analog For HDMI EDID

D-sub to D-sub DVI-D to HDMI or HDMI to HDMI

HEX EDID Table DDC Function

0001 01 00 Analog/Digital

Chassis MODEL NAME(HEX)

LD22E 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI4 78 03 0C 00 40 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI4 78 03 0C 00 40 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT MODEL NAME(HEX) HDMI1 E3 05 03 01 HDMI2 E3 05 03 01 HDMI3 E3 05 03 01 HDMI4 E3 05 03 01

ⓔ1ⓔ210 bit/

Xvycc

ⓔ2

8 bit/

Xvycc

ⓔ2

10 bit/

none XvYcc

ⓔ2

8 bit/

none XvYcc

ⓔ3

HDMI1 43 11 49 15 4D X

HDMI2 43 01 39 05 3D X

HDMI3 43 F1 29 F5 2D X

HDMI4 43 E1 19 E5 1D X

RGB X X X X X 5C

- 14 -

Only for training and service purposes

4.2. White Balance Adjustment

4.2.1. Overview

▪ W/B adj. Objective & How-it-works

(1) Objective: To reduce each Panel's W/B deviation (2) How-it-works : When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value.

(3) Adjustment condition : normal temperature

1) Surrounding Temperature : 25 °C ± 5 °C

2) Warm-up time: About 5 Min

3) Surrounding Humidity : 20 % ~ 80 %

4.2.2. Equipment

(1) Color Analyzer: CA-210 (LED Module : CH 14) (2) Adjustment Computer(During auto adj., RS-232C protocol

is needed) (3) Adjustment Remote control (4) Video Signal Generator MSPG-925F 720p/204-Gray

(Model: 217, Pattern: 49)

-> Only when internal pattern is not available

▪ Color Analyzer Matrix should be calibrated using CS-100.

4.2.3. Equipment connection MAP

4.2.4. Adj. Command (Protocol)

- LEN: Number of Data Byte to be sent

- CMD: Command

- VAL: FOS Data value

- CS: Checksum of sent data

- A: Acknowledge Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]

▪ RS-232C Command used during auto-adjustment.

Ex) wb 00 00 -> Begin white balance auto-adj.

wb 00 10 -> Gain adj. ja 00 ff -> Adj. data jb 00 c0 ... ... wb 00 1f → Gain adj. completed *(wb 00 20(Start), wb 00 2f(end)) → Off-set adj. wb 00 ff → End white balance auto-adj.

▪ Adj. Map

4.2.5. Adj. method

(1) Auto adj. method

1) Set TV in adj. mode using P-Only key.

2) Zero calibrate probe then place it on the center of the Display.

3) Connect Cable.(RS-232C to USB)

4) Select mode in adj. Program and begin adj.

5) When adj. is complete (OK Sign), check adj. status pre mode. (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

▪ W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adjustment. method

1) Set TV in Adj. mode using P-Only key.

2) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10 cm of the surface.

3) Press ADJ key → EZ adjust using adj. R/C → 7. WhiteBalance then press the cursor to the right(key ►).

(When right key(►) is pressed 216 Gray internal pattern will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value.

5) Adjustment is performed in COOL, MEDIUM, WARM 3 modes of color temperature.

▪ If internal pattern is not available, use RF input. In EZ

Adj. menu 7.White Balance, you can select one of 2 Test-pattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 216 Gray pattern.

START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS STOP

Co lor Anal yze r

Co mp ute r

Pattern Gen era to r

RS -232 C

RS- 232 C

Pro be

Sig nal Sou rce

* If TV internal pattern is used, not needed

RS-232C COMMAND

[CMD ID DATA]

Explantion

wb 00 00 Begin White Balance adjustment

wb 00 10 Gain adjustment(internal white pattern)

wb 00 1f Gain adjustment completed

wb 00 20 Offset adjustment(internal white pattern)

wb 00 2f Offset adjustment completed

wb 00 ff

End White Balance adjustment (internal pattern disappears )

Adj. item

Command

(lower caseASCII)

Data Range

(Hex.)

Default

(Decimal)

CMD1 CMD2 MIN MAX

Cool

R Gain j g 00 C0

G Gain j h 00 C0

B Gain j i 00 C0

R Cut

G Cut

B Cut

Medium

R Gain j a 00 C0

G Gain j b 00 C0

B Gain j c 00 C0

R Cut

G Cut

B Cut

Warm

R Gain j d 00 C0

G Gain j e 00 C0

B Gain j f 00 C0

R Cut

G Cut

- 15 -

Only for training and service purposes

▪ Adjustment condition and cautionary items

1) Lighting condition in surrounding area Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding.

2) Probe location : Color Analyzer(CA-210) probe should be within 10 cm

and perpendicular of the module surface.(80° ~ 100°)

3) Aging time

- After Aging Start, Keep the Power ON status during 5

Minutes.

- In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

4.2.6. Reference(White balance adjusmtment coordinate and color temperature)

▪ Luminance : 204 Gray ▪ Standard color coordinate and temperature using CS-1000

(over 26 inch)

▪

Standard color coordinate and temperature using CA-210(CH 14)

4.2.7. LED White balance table

- EDGE LED module change color coordinate because of aging time.

- Apply under the color coordinate table, for compensated

aging time.

- ALEF(LM76 series)

4.3. EYE-Q function check

(1) Turn on TV. (2) Press EYE key of Adjustment remote control. (3) Cover the Eye Q II sensor on the front of the using your

hand and wait for 6 seconds.

(4) Confirm that R/G/B value is lower than 10 of the "Raw

Data (Sensor data, Back light)". If after 6 seconds, R/G/B value is not lower than 10, replace Eye Q II sensor.

(5) Remove your hand from the Eye Q II sensor and wait for 6

seconds.

(6) Confirm that "ok" pop up. If change is not seen, replace

Eye Q II sensor.

4.4. Local Dimming Function Check

Step 1) Turn on TV. Step 2) Press “TILT” key on the Adj. R/C. Step 3) At the Local Dimming mode, module Edge Backlight

moving right to left Back light of IOP module moving. Step 4) Confirm the Local Dimming mode. Step 5) Press "exit" key.

4.5. Magic Motion Remote control test

(1) Equipment : RF Remote control for test, IR-KEY-Code

Remote control for test

(2) You must confirm the battery power of RF-Remote control

before test(recommend that change the battery per every lot)

(3) Sequence (test)

1) if you select the "Start(Wheel)" key on the Adjustment remote control, you can pairing with the TV SET.

2) You can check the cursor on the TV Screen, when select the "Wheel" key on the Adjustment remote control.

3) You must remove the pairing with the TV Set by select "Mute" key on the Adjustment remote control

Mode

Coordinate

Temp ∆uv

x y

Cool 0.269 0.273 13000 K 0.0000

Medium 0.285 0.293 9300 K 0.0000

Warm 0.313 0.329 6500 K 0.0000

Mode

Coordinate

Temp ∆uv

x y

Cool 0.269 ± 0.002 0.273 ± 0.002 13000 K 0.0000

Medium 0.285 ± 0.002 0.293 ± 0.002 9300 K 0.0000

Warm 0.313 ± 0.002 0.329 ± 0.002 6500 K 0.0000

GP4

Aging

time

(Min)

Cool Medium Warm

X y x y x y

269 273 285 293 313 329 1 0-2 283 293 299 313 320 339 2 3-5 282 291 298 311 319 337 3 6-9 281 290 297 310 318 336 4 10-19 279 289 295 309 316 335 5 20-35 277 284 293 304 314 330 6 36-49 274 279 290 299 311 325 7 50-79 271 277 287 297 308 323 8 80-119 270 274 286 294 307 320 9 Over 120 269 273 285 293 306 319

- 16 -

Only for training and service purposes

4.6. 3D function test

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4]) * HDMI mode NO. 872 , pattern No.83 (1) Please input 3D test pattern like below.

(2) When 3D OSD appear automatically, then select OK key.

(3) Don't wear a 3D Glasses, check the picture like below.

4.7. Wi-Fi Test

Step 1) Turn on TV Step 2) Select Network Connection option in Network Menu.

Step 3) Select Start Connection button in Network Connection.

Step 4) If the system finds any AP like blow PIC, it is working

well.

4.8. LNB voltage and 22KHz tone check

(only for DVB-S/S2 model) ▪ Test method

(1) Set TV in Adj. mode using POWER ON. (2) Connect cable between satellite ANT and test JIG. (3) Press Yellow key(ETC+SWAP) in Adj Remote control to

make LNB on. (4) Check LED light ‘ON’ at 18 V menu. (5) Check LED light ‘ON’ at 22 KHz tone menu. (6) Press Blue key(ETC+PIP INPUT) in Adj Remote control

to make LNB off. (7) Check LED light ‘OFF’ at 18 V menu. (8) Check LED light ‘OFF’ at 22 KHz tone menu.

▪ Test result

(1) After press LNB On key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be ON.

(2) After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be OFF.

4.9. Option selection per country

4.9.1. Overview

- Option selection is only done for models in Non-EU

4.9.2. Method

(1) Press ADJ key on the Adj. R/C, then select Country Group

Meun

(2) Depending on destination, select Country Group Code 04

or Country Group EU then on the lower Country option, select US, CA, MX. Selection is done using +, - or ►◄ key.

4.10. Tool Option selection

▪ Method : Press "ADJ" key on the Adjustment remote control,

then select Tool option.

4.11. Ship-out mode check(In-stop)

▪ After final inspection, press "IN-STOP" key of the Adjustment

remote control and check that the unit goes to Stand-by mode.

- 17 -

Only for training and service purposes

4.12. GND and Internal Pressure check

4.12.1. Method

(1) GND & Internal Pressure auto-check preparation

- Check that Power cord is fully inserted to the SET. (If loose, re-insert)

(2) Perform GND & Internal Pressure auto-check

- Unit fully inserted Power cord, Antenna cable and A/V arrive to the auto-check process.

- Connect D-terminal to AV JACK TESTER

- Auto CONTROLLER(GWS103-4) ON

- Perform GND TEST

- If NG, Buzzer will sound to inform the operator.

- If OK, changeover to I/P check automatically.

(Remove CORD, A/V form AV JACK BOX.)

- Perform I/P test

- If NG, Buzzer will sound to inform the operator.

- If OK, Good lamp will lit up and the stopper will allow the pallet to move on to next process.

4.12.2. Checkpoint

▪ TEST voltage

- GND: 1.5 KV / min at 100 mA

- SIGNAL: 3 KV / min at 100 mA ▪ TEST time: 1 second ▪ TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

- Internal Pressure TEST = POWER CORD GND & LIVE &

NEUTRAL

▪ LEAKAGE CURRENT: At 0.5 mArms

5. Audio

Measurement condition: (1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation (2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms (3) RGB PC: 1 KHz sine wave signal 0.7 Vrms

6. USB S/W Download(Service only)

(1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low, it didn't work. But your downloaded version is High, USB data is automatically detecting.

(Download Version High & Po wer only mode, Set is automatically Download)

(3) Show the message "Copying files from memory".

(4) Updating is starting.

(5) Updating Completed, The TV will restart automatically. (6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ ATV test on production line.

* After downloading, have to adjust Tool Option again.

(1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)

No. Item Min Typ Max Unit Remark

1.

Audio practical max Output, L/R (Distortion=10% max Output)

9 10 12 W EQ Off

AVL Off Clear Voice Off

8.10 10.8 Vrms

2.

Speaker (8Ω Impedance)

9 10 12 W

EQ Off AVL Off Clear Voice Off

- 18 -

Only for training and service purposes

■ Screw specification and application situation

<Warning> Check Screw Type When Screw is assembled at 'A' Part. If 'C' Screw is used at the 'A' part, Module will get damaged.

SCREW ASSEMBLY WORKING GUIDE

ח ͷͲͳ

;ͽͳͼ;ΒΔΙΚΟΖ

ח ͶͲ

• FAB30013202

(M3*L8, White, Taptite)

• 4EA

ח ͷ

Ͳͳ



;ͽͳͼ;ΒΔΙΚΟΖ

ח ͶͲ

EE

ח ͷͲͳ

;ͽͳͼ;ΒΔΙΚΟΖ

ח ͶͲ

A

B

C

C C

ח ͷͲͳ



;ͽͳͼ;ΒΔΙΚΟΖ

ͶͲ

B

A

D

AA

BB

CC

CC CC

ח ͷͲͳ



;ͽͳͼ;ΒΔΙΚΟΖ

ͶͲ

BB

AA

DD

- 19 -

Only for training and service purposes

L/R In

SPDIF OUT

USB

Audio

AMP

( STA)

I2S Out

MTK

jpG

P_TS

CVBS

P_TS

T/C Demod

IF(+/-)

USB1

RS-232C

PC-RGB

PC-AUDIO

OPTIC

LAN

SYSTEM

DDR3 X

1600 X

16

(2Gb)

HDMI1

HDMI2

HDMI3

Side

Rear

RGB,H/V

Ethernet

CVBS

UART

SYSTEM EEPROM X 1

(256Kb)

HDMI

MUX

(HDCP

EEPROM)

M-Remote

Module

Air/

Cable

TUNER

(T/C)

TUNER

(S2)

DIGITAL

DEMOD

(T/C)

DVB-S

ANALOG

DEMOD

DIGITAL

DEMOD

(S2)

TS_S/P

sui

USB2

USB3

HDMI4

eMMC X 1

(2GB)

USB_WIFI

SYSTEM

DDR3 X

1600 X 16

(2Gb)

DDR

CONTROLER A/B

SPI

LOCAL DIMMING

I2C

Sub Micom

(RENESASA)

IR

Remote Control

SYSTEM

DDR3 X

1600 X

16

(2Gb)

SYSTEM

DDR3 X

1600 X 16

(2Gb)

UART

P_TS

EPI

50P

X_TAL

27MHz

BLOCK DIAGRAM

- 20 -

Only for training and service purposes

A22

A2

A21

A5

A10

AG1

900

300

200

400

540

521

530

800

810

710

700

910

560

410

570

120

510

501

500

310

* Set + Stand

* Stand Base + Body

LV1

LV2

AG2

122

Dual Play

(Option)

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essenti al that these special safet y parts shoul d be replac ed with the same compo nents as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

CI_DATA[5]

CI_DATA[7]

MT5369_TS_OUT[2]

CI_DATA[2]

CI_DATA[4]

CI_ADDR[2]

CI_ADDR[10]

MT5369_TS_OUT[1]

CI_ADDR[13]

FE_TS_DATA[7]

CI_ADDR[5]

EMMC_DATA[7] EMMC_DATA[6]

FE_TS_DATA[5]

CI_ADDR[8]

CI_DATA[0]

CI_ADDR[6]

CI_ADDR[1]

EMMC_DATA[4]

CI_ADDR[11] CI_ADDR[12]

CI_DATA[1]

EMMC_DATA[2]

FE_TS_DATA[6]

FE_TS_DATA[0]

CI_ADDR[7]

FE_TS_DATA[4]

MT5369_TS_OUT[4]

CI_DATA[3]

EMMC_DATA[3]

EMMC_DATA[5]

FE_TS_DATA[3]

CI_ADDR[0]

MT5369_TS_OUT[7]

CI_ADDR[3]

CI_DATA[6]

FE_TS_DATA[1]

MT5369_TS_OUT[5]

MT5369_TS_OUT[0]

CI_ADDR[9]

CI_ADDR[14]

FE_TS_DATA[2]

MT5369_TS_OUT[3]

CI_ADDR[4]

MT5369_TS_OUT[6]

MODEL_OPT_2

JTRST#

FE_TS_SYNC

STB_SCL

USB_CTL3

SOC_RX

C116

0.1uF

R150 1K

MODEL_OPT_0

MT5369_TS_VAL

R147 1K OPT

/CI_CD2

R155 10K OPT

R166

2.7K OPT

EMMC_CLK

R151 1K OPT

MT5369_TS_SYNC

MT5369_TS_IN[1]

R165

4.7K

OSDA0

L/DIM0_MOSI

/USB_OCD3

R172

22

/PCM_CE1

OSDA1

+3.3V_NORMAL

MODEL_OPT_8

MODEL_OPT_6

R148 1K

JTMS

SOC_TX

CI_ADDR[0-14]

FE_TS_VAL

R167

4.7K

L/DIM0_VS

R103

4.7K

MT5369_TS_OUT[0-7]

MT5369_TS_IN[5]

EMMC_DATA[2-7]

R168

4.7K OPT

R157

4.7K OPT

R158

33 OPT

MODEL_OPT_1

CI_DATA[0-7]

JTDI

/PCM_IORD

MT5369_MISTRT

MODEL_OPT_1

CI_A_VS1

LED_PWM0

/PCM_REG

MT5369_XTAL_OUT

MT5369_MIVAL_ERR

I2C_SDA5

MT5369_XTAL_IN

AVDD_33SB

JTCLK

MODEL_OPT_5

A_DIM

FE_TS_CLK

USB_CTL2

MT5369_TS_IN[4]

SOC_RESET

/USB_OCD2

MT5369_MCLKI

/USB_OCD1

/PCM_OE

MT5369_TS_CLK

AVDD_33SB

PCM_RST

MODEL_OPT_3

MT5369_TS_IN[6]

USB_CTL1

MODEL_OPT_10

L/DIM0_SCLK

R153 1K OPT

LED_PWM1

/PCM_IOWR

JTDO

C118

0.1uF

M_REMOTE_TX

OSCL0

VDD3V3

LED_PWM1

/PCM_WE

M_REMOTE_RX

R136 33

MT5369_TS_IN[0]

MODEL_OPT_5

MODEL_OPT_3

MT5369_TS_IN[2] MT5369_TS_IN[3]

MODEL_OPT_0

+3.3V_NORMAL

ERROR_OUT

MT5369_TS_IN[7]

MODEL_OPT_6

+3.3V_NORMAL

IC104

AT24C256C-SSHL-T

NVRAM_ATMEL

3

A2

2

A1

4

GND

1

A0

5

SDA

6

SCL

7

WP

8

VCC

FE_TS_DATA[0-7]

MODEL_OPT_9

R174

10K

OPCTRL3

/PCM_WAIT

EMMC_CLK

/PCM_IRQA

R169

10K

OPT

R171

22

R170

22

OSCL1

PWM_DIM2

R137 33

R161

4.7K OPT

R178

4.7K OPT

PWM_DIM1

/CI_CD1

LED_PWM0

M_RFModule_ISP

+3.3V_NORMAL

IR

R154 1K

C117

0.1uF

I2C_SCL5

+3.3V_NORMAL

STB_SDA

X100 27MHz

MT5369_XTAL_OUTMT5369_XTAL_IN

+3.3V_NORMAL

R143 33

MTK_JTAG

JTMS

+3.3V_NORMAL

R144 10K

R152 1K

MTK_JTAG

JTDO

JTRST#

JTCLK

JTDI

AR100

10K

R149 10K

MTK_JTAG

R146 10K MTK_JTAG

R145 10K

MTK_JTAG

+3.3V_NORMAL

R139

2.7K

OSDA2

I2C_SDA2

R117 33

+3.3V_NORMAL

R115 33

I2C_SDA6

R188

2.7K

I2C_SCL4 I2C_SDA4

OSCL2

I2C_SCL5

R122 33

R160

2.7K

R116 33

I2C_SDA5

R142

2.7K

OSCL0

I2C_SCL2

STB_SDA

R111 33

R123 33

R134

2.7K

I2C_SDA1

I2C_SCL3

R114 33

R110 33

OSCL1

I2C_SCL6

I2C_SDA3

R113 33

R164

2.7K

OSDA1

R173

2.7K

R156

2.7K

R118 33

R185

2.7K

OSDA0

R177

2.7K

R112 33

I2C_SCL1

R121 33

STB_SCL

R176

10K

SC_ID_SOC

M_RFModule_RESET

R162

10K

R163

10K

/TU_RESET

RF_SWITCH_CTL

AV1_CVBS_DET

OPCTRL3

DSUB_DET HP_DET

COMP1_DET SC_DET

OPCTRL_1_SCL

OPCTRL_11_SCL

/S2_RESET

SMARTCARD_VCC

SMARTCARD_RST

SMARTCARD_DATA

SMARTCARD_CLK

SMARTCARD_DET

SMARTCARD_PWR_SEL

SMARTCARD_VCC

SMARTCARD_PWR_SEL

SMARTCARD_RST

SMARTCARD_CLK

SMARTCARD_DATA

SMARTCARD_DET

+3.3V_NORMAL

R140

4.7K

MTK_DVB_T2_TUNER

R106

4.7K

MTK_Int_FRC/URSA5

R135

4.7K

MTK_CP_BOX

R101

4.7K

MTK_FRC3/URSA5

R189

4.7K

MTK_EPI

R186

4.7K

MTK_DVB_C2_TUNER

R125

4.7K

MTK_OPTIC_Tx_IC

R130

4.7K

MTK_3D_DEPTH_IC

R108

4.7K

MTK_FHD

R175

4.7K

MTK_DVB_S_TUNER

R132

4.7K

MTK_DDR_768MB

R190

4.7K

MTK_NON_EPI

R127

4.7K

MTK_NON_OPTIC_Tx_IC

R133

4.7K

MTK_DDR_DEFAULT

R129

4.7K

MTK_NON_3D_DEPTH_IC

R141

4.7K

MTK_NON_DVB_T2_TUNER

R102

4.7K

MTK_NO_FRC/Int_FRC

R138

4.7K

MTK_NON_CP_BOX

R109

4.7K

MTK_HD

R187

4.7K

MTK_NON_DVB_C2_TUNER

R184

4.7K

MTK_NON_DVB_S_TUNER

R107

4.7K

MTK_NO_FRC/FRC3

EPI_LOCK6

OPCTRL_0_SDA

OPCTRL_10_SDA

OPCTRL_1_SCL

OPCTRL_11_SCL

OPCTRL_0_SDA

OPCTRL_10_SDA

C101

0.1uF 16V

R191 22

+3.3V_NORMAL

R192 22

I2C_SCL1

R181 4.7K

I2C_SDA1

+3.3V_NORMAL

MDS62110213

M100

MTK_H/S_3.5T

MDS62110213

M101

MTK_H/S_3.5T

MDS62110213

M102

MTK_H/S_3.5T

MDS62110213

M103

MTK_H/S_3.5T

+3.3V_NORMAL

R159 4.7K

P100

12507WS-12L

MTK_JTAG

1

2

3

4

5

6

7

8

9

10

11

12

13

C120

2.2uF 10V OPT

R193

10K

NON_EU

OPC_EN

/S2_RESET

R128

1.2K

R131

1.2K

EMMC_DATA[0]

EMMC_DATA[1]

EMMC_CMD

R119

0

IC104-*1

M24256-BRMN6TP

NVRAM_ST

3

E2

2

E1

4

VSS

1

E0

5

SDA

6

SCL

7

WC

8

VCC

C115 24pF

C113

24pF

AMP_RESET_SOC AMP_RESET_N

R124

33

AMP_RESET_BY_SOC

AMP_RESET_SOC

IC105

LGE2112

MT5369_NON_RM

JTCK

AP14

JTDI

AM14

JTDO

AR14

JTMS

AR15

JTRST

AN14

OSDA0

AP12

OSCL0

AN12

OSDA1

AP15

OSCL1

AN15

XTALI

AT34

XTALO

AU34

AVDD33_XTAL_STB

AK27

AVSS33_XTAL_STB

AH26

AVDD33_VGA_STB

AK18

AVSS33_VGA_STB

AK17

AVDD33_PLLGP

AK23

AVSS33_PLLGP

AM27

AVDD10_LDO

AJ20

GPIO0

H32

GPIO1

F37

GPIO2

F36

GPIO3

G37

GPIO4

G36

GPIO5

G35

GPIO6

G34

GPIO7

H34

GPIO8

L34

GPIO9

L32

GPIO10

K33

GPIO11

K32

GPIO12

H33

GPIO13

L35

GPIO14

K36

GPIO15

J32

GPIO16

J34

GPIO17

K34

GPIO18

K35

GPIO19

K37

GPIO20

J36

GPIO21

J37

GPIO22

J35

GPIO23

J33

GPIO24

G33

GPIO25

H35

GPIO26

H31

GPIO27

F34

GPIO28

E36

GPIO29

N33

GPIO30

P32

GPIO31

M35

GPIO32

M37

GPIO33

M33

GPIO34

F35

GPIO35

E35

GPIO36

E37

GPIO37

N32

GPIO38

M34

GPIO39

M36

GPIO40

M32

GPIO41

L33

GPIO42

E33

GPIO43

E32

GPIO44

F32

GPIO45

A29

GPIO46

D31

GPIO47

C31

GPIO48

E30

GPIO49

E31

GPIO50

F31

GPIO51

E29

GPIO52

AP9

GPIO53

AT9

GPIO54

AR9

GPIO55

AU9

ADIN0_SRV

AN23

ADIN1_SRV

AN24

ADIN2_SRV

AP23

ADIN3_SRV

AR23

ADIN4_SRV

AU23

ADIN5_SRV

AT23

ADIN6_SRV

AM24

ADIN7_SRV

AM23

U0TX

AR18

U0RX

AP18

U1RX

AU16

U1TX

AT16

POWE

A35

POOE

C33

POCE1

B34

POCE0

D33

PDD7

D29

PDD6

C30

PDD5

D30

PDD4

B31

PDD3

A31

PDD2

B32

PDD1

A32

PDD0

C32

PARB

D32

PACLE

A34

PAALE

C34

EMMC_CLK

C29

OPWRSB

AM20

ORESET

AM22

OIRI

AU21

FSRC_WR

D27

STB_SCL

AT21

STB_SDA

AR21

DEMOD_RST

T34

DEMOD_TSCLK

T32

DEMOD_TSDATA0

T36

DEMOD_TSDATA1

U36

DEMOD_TSDATA2

T33

DEMOD_TSDATA3

T30

DEMOD_TSDATA4

V33

DEMOD_TSDATA5

V32

DEMOD_TSDATA6

V31

DEMOD_TSDATA7

V30

DEMOD_TSSYNC

T35

DEMOD_TSVAL

T31

CI_INT

N36

CI_TSCLK

T37

CI_TSDATA0

R35

CI_TSSYNC

R37

CI_TSVAL

R36

PVR_TSCLK

R34

PVR_TSVAL

R32

PVR_TSSYNC

R33

PVR_TSDATA0

P33

PVR_TSDATA1

P34

SPI_CLK1

N37

SPI_CLK

P35

SPI_DATA

N34

SPI_CLE

N35

OPWM2

AU12

OPWM1

AT12

OPWM0

AR12

SD_D0

A37

SD_D1

C35

SD_D2

A36

SD_D3

B35

SD_CMD

B36

SD_CLK

B37

LDM_CS

AT11

LDM_CLK

AU11

LDM_VSYNC

AR10

LDM_DO

AM9

LDM_DI

AP10

LED_PWM1

AN22

LED_PWM0

AP21

OPCTRL11

AU20

OPCTRL10

AT20

OPCTRL9

AN18

OPCTRL8

AP20

OPCTRL7

AM18

OPCTRL6

AN19

OPCTRL5

AP19

OPCTRL4

AR19

OPCTRL3

AN21

OPCTRL2

AM19

OPCTRL1

AN20

OPCTRL0

AR20

IC104-*2

R1EX24256BSAS0A

NVRAM_RENESAS

3

A2

2

A1

4

VSS

1

A0

5

SDA

6

SCL

7

WP

8

VCC

R100

10K

AMP_RESET_BY_SOC

C114

0.1uF 16V

C105

0.1uF OPT

C106

0.1uF OPT

C100

0.1uF OPT

C103

0.1uF OPT

C102

0.1uF OPT

C104

0.1uF OPT

R120 1K

PWM1_PULL_DOWN_1K

R126 1K

PWM2_PULL_DOWN_1K

MDS61887710

M104

MTK_H/S_9.5T

IC100

M24C16-R

HDCP_EEPROM_ST

3

NC_3

2

NC_2

4

VSS

1

NC_1

5

SDA

6

SCL

7

WC

8

VCC

IC100-*1

24LC16B

HDCP_EEPROM_MICRO

3

A2

2

A1

4

VSS

1

A0

5

SDA

6

SCL

7

WP

8

VCC

R105

4.7K OPT

R104

4.7K OPT

M_RFModule_ISP

C108

2.2uF 10V

C107

2.2uF 10V

IC105-*1

LGE2112-AL

MT5369_RM

DDRV_44

AC1

DDRV_45

AC2

DDRV_1

A3

DDRV_2

A4

DDRV_5

B4

DDRV_8

C4

DDRV_10

D4

DDRV_4

B3

DDRV_7

C3

DDRV_46

AC3

DDRV_47

AC4

MEMTP

G10

MEMTN

G9

RVREF_B

G13

RVREF_A

G21

ARCKE

F10

ARCLK1

D9

ARCLK1

C9

ARCLK0

A20

ARCLK0

A21

ARODT

E18

ARRAS

F17

ARCAS

E17

ARCS

E16

ARWE

D14

ARRESET

B14

ARBA0

A13

ARBA1

G11

ARBA2

D16

ARCSX

F18

ARA14

C15

ARA13

A15

ARA12

F13

ARA11

C14

ARA10

F11

ARA9

E15

ARA8

D13

ARA7

B15

ARA6

E14

ARA5

F16

ARA4

E13

ARA3

B13

ARA2

A14

ARA1

F14

ARA0

F15

ARDQM0

C19

ARDQS0

C21

ARDQS0

B21

ARDQ0

C23

ARDQ1

B17

ARDQ2

D23

ARDQ3

C17

ARDQ4

D24

ARDQ5

C16

ARDQ6

C24

ARDQ7

D15

ARDQM1

D21

ARDQS1

B20

ARDQS1

C20

ARDQ8

A17

ARDQ9

A23

ARDQ10

D17

ARDQ11

B23

ARDQ12

D20

ARDQ13

D22

ARDQ14

D19

ARDQ15

C22

ARDQM2

A7

ARDQS2

B9

ARDQS2

A9

ARDQ16

C12

ARDQ17

D6

ARDQ18

B12

ARDQ19

C5

ARDQ20

C13

ARDQ21

A5

ARDQ22

A12

ARDQ23

B5

ARDQM3

E10

ARDQS3

C8

ARDQS3

D8

ARDQ24

C6

ARDQ25

D10

ARDQ26

D7

ARDQ27

C11

ARDQ28

C7

ARDQ29

C10

ARDQ30

B7

ARDQ31

B10

AVDD33_MEMPLL

N14

AVSS33_MEMPLL

N15

DVSS_50

R1

DVSS_48

P21

8

MID_MAIN_1

2011.12.13

LG FRC2

3D DEPTH

T2 Tuner

MODEL OPTION 8 is just for CP Box It should not be appiled at MP

NON_3D_Depth_IC

S Tuner

SoC internal FRC

SOC -> CI SLOT

NON_OPTIC

CI SLOT -> SOC

SOC -> CI SLOT

MODEL_OPT_9

OPTIC

1

MODEL_OPT_7

MODEL_OPT_3

Support

FHD

Write Protection

- Low : Normal Operation

- High : Write Protection

Disable

Reserved

DDR_768MB

EPI

Reserved

MODEL_OPT_2

DDR

MODEL_OPT_6

HIGH

MODEL_OPT_8

CI SLOT -> SOC

MODEL_OPT_0

Not Support

Default

1

Not Support

CP BOX

MODEL_OPT_5

0

CI SLOT -> SOC

Support

Enable

LOW

1

NO_FRC

NVRAM

Model Option

0

Close to eMMC Flash (IC8100)

MODEL_OPT_10

0

CI SLOT -> SOC

HD

STRAPPING LED_PWM0 LED_PWM1 OPCTRL3

ICE mode + 27M + Serial boot 0 0 0

ICE mode + 27M + ROM to Nand boot 0 0 1

ICE mode + 27M + Rom to eMMC boot 0 1 0 from eMMC pins (share pins w/s NAND)

ICE mode + 27M + ROM to eMMC boot 0 1 1 from SDIO pins

DDR_Default

EXTERNAL DEMOD

-> SOC

MODEL_OPT_1

1

MODEL_OPT_4

3D_Depth_IC

X-TAL

JTAG

I2C

I2C_1 : AMP, L/DIMMING,HDCP KEY I2C_2 : T-CON I2C_3 : MICOM I2C_4 : S/Demod,T2/Demod, LNB I2C_5 : NVRAM I2C_6 : TUNER_MOPLL(T/C,ATV)

FOR JAPAN

HDCP EEPROM

Support

Not Support

HEAT SINK SMD GASKET

5V Tolerance

MODEL_OPT_4

Crystal Matching Test result : 27pF -> 20pF -> 24pF

IC

EAX6430790* : LD22* / LC22* EAX6443420* : LT22* / LJ22* / LA22* / LB22*

MODEL_OPT_7

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

CI_ADDR[3]

CI_DATA[7]

CI_ADDR[4]

CI_DATA[2]

MT5369_TS_OUT[1]

CI_ADDR[7] CI_ADDR[8]

CI_ADDR[10]

CI_ADDR[14]

CI_DATA[5]

MT5369_TS_OUT[6]

CI_DATA[6]

MT5369_TS_OUT[4]

CI_DATA[3]

CI_ADDR[12]

MT5369_TS_OUT[7]

CI_ADDR[0]

CI_ADDR[5]

MT5369_TS_OUT[2]

CI_ADDR[11]

MT5369_TS_OUT[5]

CI_DATA[0]

CI_ADDR[1]

CI_DATA[1]

CI_DATA[4]

CI_ADDR[13]

CI_ADDR[6]

MT5369_TS_OUT[0]

CI_ADDR[2]

MT5369_TS_OUT[3]

CI_ADDR[9]

C323

0.1uF

MT5369_TS_IN[0]

TP324

C343 100pF 50V

C3690.01uF

HDMI_HPD_3_JACK

TP337

AV1_R_IN_SOC

D0+_HDMI2_JACK

TXA4P

TP353

COMP1_Pr_SOC

R3791.2K

TP321

R358100

SCART_Rout_SOC

TP345

C355

0.047uF T/C&AT&CHB

DTV/MNT_V_OUT_SOC

C3740.01uF

R323

22

TP378

C397 1200pF

C359 0.047uF

TP374

TXD1P

C398 1200pF

R330 75 1%

C382

0.1uF

C354

0.1uF

/PCM_WE

MT5369_TS_IN[5]

TP375

R311 30K

HP_LOUT_AMP

VDD3V3

TXCCLKP

HP_ROUT_AMP

MT5369_TS_IN[4]

HDMI_HPD_2_JACK

TP372

TXA0N

D2+_HDMI3_JACK

HP_ROUT_MAIN

TP326

C307

0.1uF

C336

1uF

10V

T/C&AT&CHB

R373

0

C384 10pF 50V

TXDCLKN

IF_AGC

C361 1uF

CK+_HDMI4_JACK

TXD0P

R3781.2K

VDD3V3

SC_R_SOC

R3521.2K

HP_OUT

D2-_HDMI3_JACK

TXC1P

PC_R_IN_SOC

C380

0.1uF

DSUB_VSYNC

TXD2N

TP322

TP307

TXB2P

C400 1200pF

TP350

PC_L_IN_SOC

+1.2V_MTK_AVDD

C3710.01uF

AV1_CVBS_IN_SOC

TXC1N

TP329

+1.2V_MTK_AVDD

R341 100

R309 100K

TXD0N

PC_R_IN

EPHY_TDP

C391 27pF 50V OPT

TP311

R371 100

D2-_HDMI4_JACK

R310 30K

TP318

SCART_Rout_SOC

C386 27pF 50V OPT

TXB1P

DSUB_HSYNC_SOC

AUD_LRCH

R300 470K OPT

DDC_SDA_1_SOC

TP313

TXC2N

TP348

C332

0.22uF 10V

HP_OUT

C3660.01uF

TXC0P

SC_B_SOC

CK-_HDMI2_JACK

OSCL2 OSDA2

D1-_HDMI2_JACK

C302

0.1uF

R354 75 1%

DSUB_VSYNC_SOC

C392 27pF 50V OPT

C395 1200pF

HP_OUT

DDC_SCL_4_JACK

R335 51

T/C&AT&CHB

TXDCLKP

TXA1P

EPHY_RDP

TP365

DAC_3V3

C385 27pF 50V OPT

PC_L_IN_SOC

SCART_Lout_SOC

5V_HDMI_2_JACK

R368 100

AV1_L_IN_SOC

TP355

+1.2V_MTK_AVDD

C331

0.22uF 10V

HP_OUT

C383 1200pF HP_OUT

TP300

D1+_HDMI3_JACK

R3701.2K

HP_OUT

SC_G_SOC

TP341

D0-_HDMI1_SOC

DDC_SCL_2_JACK

R343 24K

1%

VDD3V3

SC_G_SOC

TP370

AV1_R_IN

C341

0.047uF T/C&AT&CHB

TP308 C393 22pF

OPT

D0+_HDMI1_SOC

R367 100

C387 22pF

OPT

TXA4N

VDD3V3

R372

0

TP330

C308

0.1uF

TP351

TP366

/CI_CD1

C319 10uF 16V

R362100

TP360

TXD3P

D0+_HDMI4_JACK

TP334

MT5369_MISTRT

C3701500pF

R301 470K

OPT

D1+_HDMI1_SOC

D2+_HDMI2_JACK

C314 100pF 50V OPT

COMP1_Pr_SOC

TXB1N

SC_L_IN_SOC

C340 47pF 50V

C364

0.1uF

ARC

TP317

SC_DET

C344 27pF 50V OPT

TXA3N

C300 560pF 50V OPT

SPDIF_OUT

TP359

C301 560pF 50V OPT

D0-_HDMI4_JACK

C351

0.1uF

IF_P

TU_CVBS

WIFI_DM

TXD4N

R334 51

T/C&AT&CHB

R3500

R357100

TXA1N

TXACLKP

TXC0N

L303

BLM18PG121SN1D

HP_OUT

TUNER_SIF

TP338

/PCM_IRQA

MT5369_MIVAL_ERR

SC_R_SOC

TP320

DDC_SCL_3_JACK

R324

22

C316

0.1uF

TP373

R3511.2K

HP_OUT

MT5369_TS_IN[6] MT5369_TS_IN[7]

C337 1uF

10V

T/C&AT&CHB

/PCM_REG

TP352

VDD3V3

HDMI_HPD_1_SOC

EPHY_RDN

WIFI_DP

C3720.01uF C3730.01uF

R308

1.2K OPT

R366 100

+1.2V_MTK_AVDD

TXA2P

C3670.01uF

D2-_HDMI2_JACK

DSUB_G+

R328 470K OPT

TP314

DDC_SDA_2_JACK

D1+_HDMI4_JACK

+1.2V_MTK_AVDD

TP335

VDD3V3

C399 1200pF

L302

BLM18PG121SN1D

HP_OUT

D2+_HDMI1_SOC

R353 75 1%

AUDIO_R_OUT_COMMERCIAL

TP356

PCM_5V_CTL

TP336

R31524K

D1+_HDMI2_JACK

MT5369_TS_SYNC

TP328

R322 75

HP_ROUT

MT5369_MCLKI

TP310

R361100

MT5369_TS_VAL

C320 10uF 16V

TP342

CK+_HDMI3_JACK

RGB_DDC_SDA

TXB0N

C390 1200pF HP_OUT

VDD3V3

R355 75

1%

AUD_LRCK

TP358

HP_LOUT_MAIN

TXC2P

TXB4P

C377

1200pF

HP_OUT

C3680.01uF

TP346

TXB4N

C329 5pF 50V

OPT

EPHY_TDN

TP312

AUD_MASTER_CLK

TXD2P

/PCM_IORD

MT5369_TS_CLK

TP343

TP362

TXACLKN

D2+_HDMI4_JACK

/PCM_CE1

COMP1_Pb_SOC

MT5369_TS_IN[2]

PC_L_IN

R321 75

MT5369_TS_IN[1]

R320 75

TP349

TXA2N

R307 1K

C394 27pF 50V OPT

C304

0.1uF

DTV/MNT_V_OUT_SOC

R329 470K OPT

TXCCLKN

TP319

SC_COM_SOC

HDMI_ARC

AV1_R_IN_SOC

R339

2.2K OPT

AV1_CVBS_IN_SOC

C388 27pF 50V OPT

HDMI_HPD_4_JACK

R3761.2K

CK-_HDMI4_JACK

D1-_HDMI4_JACK

TP347

CK-_HDMI3_JACK

D0+_HDMI3_JACK

TXB3P

SC_FB_SOC

COMP1_Y_SOC

D1-_HDMI1_SOC

TXB0P

R356100

5V_HDMI_4_JACK

C389 22pF OPT

CK-_HDMI1_SOC

R374

0

COMP1_Pr

TP377

R3771.2K

C346 10uF 16V

C360 0.047uF

R305

1K

TP367

TP323

C363

1uF

25V

AV1_L_IN

/PCM_OE

TXD3N

C315 100pF 50V OPT

R3691.2K

HP_OUT

5V_HDMI_3_JACK

TP331

SC_R_IN_SOC

R326

2K

OPT

SC_CVBS_IN_SOC

VDD3V3

C328

0.1uF

SC_COM_SOC

SC_ID_SOC

SC_L_IN_SOC

RGB_DDC_SCL

CK+_HDMI1_SOC

CI_DATA[0-7]

C330

5pF 50V OPT

C358

0.01uF 50V

MT5369_TS_OUT[0-7]

TP316

D0-_HDMI2_JACK

C345 10uF 16V

CK+_HDMI2_JACK

DDC_SDA_4_JACK

ARC

COMP1_Pb

C303

0.1uF

AV1_CVBS_IN

C3751500pF

R340 100

TP339

SC_FB_SOC

IF_N

R342 10K

T/C&AT&CHB

SC_CVBS_IN_SOC

TXC4N

TP371

R359100

C379 10pF 50V

DDC_SDA_3_JACK

+1.2V_MTK_AVDD

TXA0P

DDC_SCL_1_SOC

DSUB_HSYNC

TXC4P

C378 10pF 50V

TP340

COMP1_Y_SOC

R332 10K

T/C&AT&CHB

C347

0.1uF

AUD_SCK

SC_R_IN_SOC

TP357

C338 560pF 50V OPT

TP325

PCM_RST

D2-_HDMI1_SOC

D1-_HDMI3_JACK

/PCM_IOWR

SC_B_SOC

TP363

R306

1K

DSUB_VSYNC_SOC

SCART_Lout_SOC

R304

1K

TXC3P

CI_ADDR[0-14]

R303

82

TP315

TP309

TP332

AV1_L_IN_SOC

D0-_HDMI3_JACK

/PCM_WAIT

AUDIO_L_OUT_COMMERCIAL

R363100

5V_HDMI_1_SOC

TP368

TXBCLKN TXBCLKP

COMP1_Y

TP344

TP361

R3490

OPT

HP_LOUT

CI_A_VS1

DSUB_R+

COMP1_Pb_SOC

/CI_CD2

TP327

TP364

TP369

TXA3P

TXB2N

TXB3N

C342 100pF 50V

TP333

MT5369_TS_IN[3]

C339 560pF 50V OPT

R325

2K

OPT

R302

180

C352 0.01uF

TXC3N

PC_R_IN_SOC

DSUB_B+

R364100

DSUB_HSYNC_SOC

TXD4P

TP354

C396 33pF OPT

+5V_NORMAL

TXD1N

C306

0.1uF

MODEL_OPT_10

2D/3D_CTL

MODEL_OPT_2

PCM_5V_CTL

EMMC_RST

MODEL_OPT_8 MODEL_OPT_9

VCOM_DYN

GST_SOC

MCLK_SOC

GCLK_SOC

EO_SOC

PMIC_RESET

C365

0.01uF

C305

1uF

25V

C362

0.1uF

C350

0.1uF

R314

0

R336

0

R331 0

T/C&AT&CHB

R346 0

T/C&AT&CHB

C309 OPT

C311 1uF

10V

C310

33pF

T/C&AT&CHB

C312

33pF

T/C&AT&CHB

C334 47pF 50V

C335 47pF 50V

C333 47pF 50V

USB_DP2 USB_DM2

USB_DP1 USB_DM1

USB_DM3

USB_DP3

IC105

LGE2112

HDMI_CEC

AA32

HDMI_0_SCL

AG33

HDMI_1_SCL

AE33

HDMI_2_SCL

AC33

HDMI_3_SCL

AH32

HDMI_0_SDA

AF33

HDMI_1_SDA

AD33

HDMI_2_SDA

AB33

HDMI_3_SDA

AH33

HDMI_0_PWR5V

AG31

HDMI_1_PWR5V

AE31

HDMI_2_PWR5V

AC31

HDMI_3_PWR5V

AH31

HDMI_0_HPD

AG32

HDMI_1_HPD

AE32

HDMI_2_HPD

AC32

HDMI_3_HPD

AJ32

AVDD12_HDMI_0_RX

AA24

AVDD12_HDMI_1_RX

Y24

AVDD12_HDMI_2_RX

W24

AVDD12_HDMI_3_RX

AB24

AVDD33_HDMI_0_RX

AB29

AVDD33_HDMI_1_RX

AA29

AVDD33_HDMI_2_RX

Y29

AVDD33_HDMI_3_RX

AC29

AVSS33_HDMI_RX_1

AB30

AVSS33_HDMI_RX_2

AD30

AVSS33_HDMI_RX_3

AF31

AVSS33_HDMI_RX_4

AF32

USB_DP_P0

C36

USB_DM_P0

C37

USB_DP_P1

D36

USB_DM_P1

D37

USB_DP_P2

AT13

USB_DM_P2

AU13

USB_DP_P3

AT14

USB_DM_P3

AU14

AVDD33_USB_P0P1

D35

AVDD33_USB_P2P3

AP13

AVSS33_USB_P1

D34

AVSS33_USB_P2

AR13

PCIE11_TXP

W35

PCIE11_TXN

W34

PCIE11_RXN

Y34

PCIE11_RXP

Y35

AVDD12_PCIE11

U24

AVDD33_PCIE11

V24

AVSS12_PCIE11

W30

PCIE11_REFCKN

W36

PCIE11_REFCKP

W37

HDMI_0_RX_0

AG35

HDMI_0_RX_0B

AG34

HDMI_0_RX_1

AG37

HDMI_0_RX_1B

AG36

HDMI_0_RX_2

AF35

HDMI_0_RX_2B

AF34

HDMI_0_RX_C

AH35

HDMI_0_RX_CB

AH34

HDMI_1_RX_0

AE37

HDMI_1_RX_0B

AE36

HDMI_1_RX_1

AD35

HDMI_1_RX_1B

AD34

HDMI_1_RX_2

AC35

HDMI_1_RX_2B

AC34

HDMI_1_RX_C

AE35

HDMI_1_RX_CB

AE34

HDMI_2_RX_0

AB35

HDMI_2_RX_0B

AB34

HDMI_2_RX_1

AA35

HDMI_2_RX_1B

AA34

HDMI_2_RX_2

AA37

HDMI_2_RX_2B

AA36

HDMI_2_RX_C

AC37

HDMI_2_RX_CB

AC36

HDMI_3_RX_0

AK35

HDMI_3_RX_0B

AK34

HDMI_3_RX_1

AJ35

HDMI_3_RX_1B

AJ34

HDMI_3_RX_2

AJ37

HDMI_3_RX_2B

AJ36

HDMI_3_RX_C

AJ33

HDMI_3_RX_CB

AK33

TXVP_0

AT18

TXVN_0

AU18

RXVN_1

AU17

RXVP_1

AT17

PHYLED1

AN16

PHYLED0

AM16

REXT

AD15

AVDD12_REC

AD14

AVDD33_COM

AD16

AVDD33_LD

AD17

AVSS33_LD

AL16

AVSS33_COM

AL15

AVSS12_REC

AL14

IC105

LGE2112

TCON0

F27

TCON1

E27

TCON2

F30

TCON3

F29

TCON4

B27

TCON5

A27

TCON6

B28

TCON7

A28

TCON8

C28

TCON9

D28

TCON10

E28

TCON11

F28

TCON12

B29

AVDD12_LVDS_1

AG6

AVDD12_LVDS_2

AJ6

AVDD12_VPLL

AF6

AVDD33_LVDSB

AE6

AVDD33_LVDSA

AH7

AVSS12_LVDS_2

AJ5

AVSS12_LVDS_1

AG5

AVSS12_VPLL

AF5

AVSS33_LVDSB

AE5

AVSS33_LVDSA

AH5

REXT_VPLL

AG7

AIN0_R_AADC

AU37

AIN0_L_AADC

AU35

AIN1_R_AADC

AT35

AIN1_L_AADC

AT37

AIN2_R_AADC

AU36

AIN2_L_AADC

AP34

AIN3_R_AADC

AT36

AIN3_L_AADC

AR37

AIN4_R_AADC

AR33

AIN4_L_AADC

AP32

AIN5_R_AADC

AR36

AIN5_L_AADC

AP37

AIN6_R_AADC

AR35

AIN6_L_AADC

AP36

AVDD33_AADC

AL31

AVSS33_AADC

AJ28

VMID_AADC

AJ27

MPXP

AN28

ADCINP_DEMOD

AU32

ADCINN_DEMOD

AT32

AVDD33_DEMOD

AD22

AVDD12_DEMOD

AL27

AVSS33_DEMOD

AM28

AVSS12_DEMOD

AJ26

IF_AGC

U35

RF_AGC

U34

LOUTN

AP31

LOUTP

AN30

OSCL2

V35

OSDA2

V34

SC0

AP28

SY0

AR29

CVBS3P

AT30

CVBS2P

AR30

CVBS1P

AR31

CVBS0P

AN29

CVBS_COM

AP30

AVDD33_CVBS_1

AK24

AVDD33_CVBS_2

AK25

AVSS33_CVBS_1

AL25

AVSS33_CVBS_2

AM26

AO3N

AG3

AO3P

AG4

AO4N

AG1

AO4P

AG2

AOCLKN

AF3

AOCLKP

AF4

AO2N

AE3

AO2P

AE4

AO1N

AE1

AO1P

AE2

AO0N

AD1

AO0P

AD2

AE4N

AL3

AE4P

AL4

AE3N

AL1

AE3P

AL2

AECLKN

AK3

AECLKP

AK4

AE2N

AJ3

AE2P

AJ4

AE1N

AJ1

AE1P

AJ2

AE0N

AH3

AE0P

AH4

BO4N

AT2

BO4P

AU2

BO3N

AT1

BO3P

AU1

BOCLKN

AR1

BOCLKP

AR2

BO2N

AP1

BO2P

AP2

BO1N

AN1

BO1P

AN2

BO0N

AM3

BO0P

AM4

BE4N

AT6

BE4P

AU6

BE3N

AP6

BE3P

AR6

BECLKN

AP5

BECLKP

AR5

BE2N

AT4

BE2P

AU4

BE1N

AP4

BE1P

AR4

BE0N

AP3

BE0P

AR3

AR0_ADAC

AN35

AL0_ADAC

AN34

AR1_ADAC

AM32

AL1_ADAC

AM34

AR2_ADAC

AM37

AL2_ADAC

AM33

AR3_ADAC

AM36

AL3_ADAC

AM35

AVDD33_DAC

AG30

AVDD33_DAC1

AF30

AVSS33_DAC

AK30

AVSS33_DAC1

AE30

ALIN

Y33

ASPDIF0

AR16

ASPDIF1

Y32

AOBCK

AR11

AOLRCK

AP11

AOMCLK

AM12

AOSDATA4

AM10

AOSDATA3

AM11

AOSDATA2

AN11

AOSDATA1

AN10

AOSDATA0

AN9

HSYNC

AN25

VSYNC

AM25

RP

AR25

GP

AR24

BP

AU24

COM

AP24

SOG

AT24

VGA_SDA

AR22

VGA_SCL

AP22

COM1

AT26

PB1P

AR26

PR1P

AP26

Y1P

AU26

SOY1

AP25

COM0

AU28

PB0P

AT28

PR0P

AR28

Y0P

AP27

SOY0

AR27

VDACX_OUT

AU30

VDACY_OUT

AP29

AVDD33_VDAC_BG

AD20

AVDD33_VDAC

AD21

AVDD12_RGB

AD19

AVSS33_VDAC_BG

AJ22

AVSS12_RGB

AJ21

AVSS33_VDAC

AL24

L301

BLM15BD121SN1

L300

BLM15BD121SN1

L304

BLM15BD121SN1

ZD304

5.48VTO5.76V ZD305

5.48VTO5.76V

ZD306

5.48VTO5.76V ZD307

5.48VTO5.76V

ZD302

5.48VTO5.76V

ZD300

5.48VTO5.76V

ZD303

5.48VTO5.76V

ZD301

5.48VTO5.76V

D300

5.5V

ADLC 5S 02 015

D302

5.5V

ADLC 5S 02 015

D301

5.5V

ADLC 5S 02 015

R344

30K

R345

30K

C348 100pF 50V

R338 0

R337 0

R333

120-ohm

9

MID_MAIN_2

2011.12.19

Close to MT5369

Place at JACK SIDE

1608 sizs For EMI

PLACE AT JACK SIDE

Close to Tuner

1.0Vpp

Close to Tuner

CHANGE SYMBOL

1608 sizs For EMI

Don’t use as GPIO

FOR EMI

CH1

CH2

CH3

CH4

CH5

CH6

1608 sizs For EMI

For PCB Pattern

Close to MT5369

Port was changed !!!!

PLACE AT JACK SIDE

1608 sizs For EMI

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

C532

0.1uF

+3.3V_NORMAL

POWER_ON/OFF1

C544

0.1uF 16V

C535

0.1uF

C503 10uF

C539 10uF

+1.2V_MTK_CORE

EMMC_VCCQ

C550

0.1uF

C525 10uF

+1.2V_MTK_CORE

C529

0.1uF

+1.2V_MTK_CORE

TP500

3.3V_EMMC

R500 1

C512

0.1uF 16V

C546

0.1uF

C540 10uF 10V

TP501

C543

0.1uF

L500

BLM18PG121SN1D

DAC_3V3

LAN_JACK_POWER

+3.3V_NORMAL

L504

BLM18PG121SN1D

+3.3V_NORMAL

VDD3V3

C548

0.1uF

C500 10uF

C510

0.1uF +1.2V_MTK_CORE

VDD3V3

C522

0.1uF 16V

C526 10uF 10V

L506 BLM18PG121SN1D

+5V_NORMAL

C552

0.1uF

C553

0.1uF

VDD3V3

L501

BLM18PG121SN1D

C501

0.1uF

AVDD_33SB

L502

BLM18PG121SN1D

C502

0.1uF

+1.2V_MTK_CORE +1.2V_MTK_AVDD

C505 10uF

C506 10uF

+1.2V_MTK_CORE

+1.5V_DDR

IC501

AP1117E33G-13

OUT

INADJ/GND

C524 10uF

IC105

LGE2112

DVSS_51

R2

DVSS_52

R3

DVSS_37

J4

DVSS_53

R4

DVSS_107

Y4

DVSS_20

F5

DVSS_38

J5

DVSS_54

R5

DVSS_108

Y5

DVSS_95

W5

DVSS_44

L7

DVSS_46

M7

DVSS_56

R7

DVSS_120

AA5

DVSS_130

AB5

DVSS_43

K7

DVSS_77

U7

DVSS_97

W7

DVSS_13

E9

DVSS_12

E8

DVSS_22

F9

DVSS_28

G14

DVSS_39

J6

DVSS_57

R15

DVSS_68

T15

DVSS_78

U15

DVSS_87

V15

DVSS_99

W15

DVSS_112

Y15

DVSS_122

AA15

DVSS_132

AB15

DVSS_34

H11

DVSS_58

R16

DVSS_69

T16

DVSS_79

U16

DVSS_88

V16

DVSS_100

W16

DVSS_113

Y16

DVSS_123

AA16

DVSS_133

AB16

DVSS_59

R17

DVSS_70

T17

DVSS_80

U17

DVSS_89

V17

DVSS_114

Y17

DVSS_71

T18

DVSS_90

V18

DVSS_115

Y18

DVSS_72

T19

DVSS_91

V19

DVSS_116

Y19

DVSS_101

W17

DVSS_124

AA17

DVSS_134

AB17

DVSS_60

R18

DVSS_131

AB6

DVSS_35

H19

DVSS_36

H22

DVSS_40

J11

DVSS_41

J12

DVSS_42

J22

DVSS_55

R6

DVSS_62

R20

DVSS_73

T20

DVSS_83

U20

DVSS_92

V20

DVSS_104

W20

DVSS_117

Y20

DVSS_127

AA20

DVSS_137

AB20

DVSS_29

G16

DVSS_63

R21

DVSS_74

T21

DVSS_84

U21

DVSS_93

V21

DVSS_105

W21

DVSS_118

Y21

DVSS_128

AA21

DVSS_138

AB21

DVSS_64

R22

DVSS_75

T22

DVSS_85

U22

DVSS_94

V22

DVSS_106

W22

DVSS_119

Y22

DVSS_129

AA22

DVSS_139

AB22

DVSS_65

R23

DVSS_76

T23

DVSS_86

U23

DVSS_140

AB23

DVSS_96

W6

DVSS_30

G17

DVSS_27

F25

DVSS_109

Y6

DVSS_17

E21

DVSS_25

F21

DVSS_45

L8

DVSS_66

T7

DVSS_7

D11

DVSS_14

E11

DVSS_8

D12

DVSS_18

E22

DVSS_26

F22

DVSS_33

G25

DVSS_136

AB19

DVSS_126

AA19

DVSS_49

P22

DVSS_103

W19

DVSS_82

U19

DVSS_61

R19

DVSS_110

Y7

DVSS_135

AB18

DVSS_125

AA18

DVSS_102

W18

DVSS_81

U18

DVSS_121

AA7

DVSS_47

N22

DVSS_67

T8

DVSS_98

W8

DVSS_111

Y8

DVSS_11

E7

DVSS_21

F8

IC105

LGE2112

VCCK_43

AR7

VCCK_45

AT7

VCCK_47

AU7

VCCK_42

AP8

VCCK_44

AR8

VCCK_46

AT8

VCCK_48

AU8

VCCK_37

AM7

VCCK_39

AN7

VCCK_41

AP7

VCCK_38

AM8

VCCK_40

AN8

VCCK_1

P14

VCCK_9

R14

VCCK_11

T14

VCCK_13

U14

VCCK_14

V14

VCCK_16

W14

VCCK_18

Y14

VCCK_20

AA14

VCCK_22

AB14

VCCK_23

AC14

VCCK_28

AC19

VCCK_2

P15

VCCK_24

AC15

VCCK_3

P16

VCCK_25

AC16

VCCK_15

V23

VCCK_17

W23

VCCK_19

Y23

VCCK_21

AA23

VCCK_31

AC22

VCCK_32

AC23

VCCK_36

AD24

VCCK_8

P23

VCCK_10

R24

VCCK_12

T24

VCCK_33

AC24

VCCK_30

AC21

VCCK_7

P20

VCCK_29

AC20

VCCK_6

P19

VCCK_27

AC18

VCCK_5

P18

VCCK_26

AC17

VCCK_4

P17

VCCK_34

AD18

VCCK_35

AD23

VCC3IO_B_4

AL9

VCC3IO_B_2

AK10

VCC3IO_B_1

AK9

VCC3IO_B_3

AK11

VCC3IO_A_5

H29

VCC3IO_A_7

J29

VCC3IO_A_6

H30

VCC3IO_A_8

J30

VCC3IO_A_3

G31

VCC3IO_A_4

G32

VCC3IO_A_2

F33

VCC3IO_A_1

E34

MDS62110209

M501

SMD_GASKIT_8.5T_RGB

MDS62110209

M500

SMD_GASKIT_8.5T_LAN

MDS62110209

M502

SMD_GASKIT_8.5T_COMP

C545

0.1uF

+1.2V_MTK_CORE

C531

0.1uF

C537

0.1uF

+1.5V_DDR

C547

0.1uF

C533

0.1uF

C536

0.1uF

C520

0.1uF

C527

0.1uF

C514

0.1uF

C508

0.1uF

C523

0.1uF

MDS62110217

M504

SMD_GASKIT_12.5T_USB1

MDS62110217

M506

SMD_GASKIT_12.5T_HDMI1

MDS62110217

M503

SMD_GASKIT_12.5T_HDMI2

MDS62110217

M505

SMD_GASKIT_12.5T_USB3

C504

2.2uF

10

2011.12.09

MID_MAIN_3

60mA

5600mA

DECAP FOR SOC (HIDDEN - UCC) DECAP FOR SOC (BOTTOM)

SMD Gaskit

LAN RGB COMP

HDMI2~3HDMI1~2 USB1~2 USB3

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SC_FB_SOC

C605 10pF

EU

C614 0.01uF

EU

R610 51K

1/16W 1%

EU

R607 75 1%

EU

SC_FB

SC_B_SOC

C601 10pF

OPT

SC_L_IN_SOC

C606 10pF

EU

C613 0.01uF

EU

SC_R_IN

SC_CVBS_IN_IF

R615

75 1%

EU

SC_ID

R617 100

EU

SC_CVBS_IN

SC_G

C615 0.01uF

EU

SCART_Lout

SC_ID_SOC

SC_R_SOC C604 10pF

EU

R604 75 1%

EU

R622 100

EU R606 75 1%

EU

SC_CVBS_IN_SOC

C616 0.047uF

EU

R621 100

EU

R609 22

EU

SC_R_IN_SOC

R620 100

EU

R613 10K

EU

R616

75 1%

EU

SCART_Rout_SOC

SC_B

R601 470K OPT

SC_R

SCART_Rout

R61815K

EU

DTV/MNT_V_OUT_SOC

R605 75 1%

EU

TU_CVBS

R608 75 1%

EU

C612 0.01uF

EU

SC_COM_SOC

SC_CVBS_IN_IF

SC_L_IN

SCART_Lout_SOC

R623 100

EU

DTV/MNT_V_OUT

SC_G_SOC

R61915K

EU

R602 470K OPT

C610 10uF 16V

EU

C611 10uF 16V

EU

C603 330pF 50V OPT

C602 330pF 50V

OPT

R600

EU

0

TP600

C600 220pF OPT

C617 220pF

OPT

R627 330pF 50V

EU

R603 330pF 50V

EU

+12V

R630 100K

OPT

R631 100K

OPT

R628 100K

OPT

R629 100K

OPT

+12V

R632

EU

0

R633

EU

0

SCART_AMP_R_FB

SCART_AMP_L_FB

R612

EU

0

R634

EU

0

R614 0

1/16W 5%

EU

R624 0

1/16W 5%

EU

R625

30K

EU

R626

30K

EU

C608 100pF 50V

EU

C609 100pF 50V

EU

C607 100pF EU

R611

EU

120-ohm

R635

10K

EU

R636

10K EU

2011.12.30

11

MID_MAIN_SCART

PLACE AT MAIN SOC SIDE

PLACE AT JACK SIDE

READY FOR FILTER (EMI)

PLACE AT IC6000

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

BRDQ[30]

BRDQ[18]

BRA[10]

ARDQ[30]

BRA[1]

BRDQ[22]

BRA[4]

ARDQ[22]

ARDQ[26]

ARA[11]

ARA[0]

BRA[12]

ARA[6]

BRA[10]

BRDQ[28]

BRA[7]

ARDQ[20]

BRA[6]

BRA[5]

BRA[9]

ARA[8]

ARA[5]

ARA[9]

ARA[6]

ARA[5]

ARA[0]

ARDQ[16]

BRA[8]

BRA[11]

ARDQ[28]

ARA[3]

BRA[7]

ARA[7]

ARA[5]

ARA[10]

ARA[11]

BRDQ[17]

BRA[1]

BRA[8]

BRA[14]

BRA[13]

ARA[7]

ARDQ[19]

BRA[2]

ARA[0]

ARA[2]

ARA[13]

BRA[5]

ARA[8]

BRA[3]

BRA[11]

BRA[12]

ARA[6]

BRDQ[26]

ARA[13]

ARA[9]

ARDQ[17]

BRDQ[23]

BRA[3]

ARA[1]

ARA[3]

BRA[0]

BRA[11]

ARA[12]

BRA[12]

BRDQ[20]

ARDQ[31]

ARA[4]

BRDQ[31]

BRA[8]

ARA[12]

BRDQ[27]

BRDQ[19]

ARA[10]

ARA[4]

ARA[11]

ARA[2]

ARDQ[27]

ARA[4]

ARA[1]

BRA[0] BRA[1]

BRA[9]

ARA[3]

ARA[7]

BRA[10]

BRA[2]

BRDQ[21]

BRA[4]

BRA[13]

ARDQ[21]

BRA[7]

ARDQ[29]

ARDQ[18]

BRDQ[25]

BRA[3]

ARA[8]

BRDQ[24]

ARA[9]

ARA[10]

BRDQ[29]

ARDQ[24]

BRA[13]

BRA[6]

ARDQ[25]

ARA[13]

BRA[5]

ARDQ[23]

BRA[2]

BRDQ[16]

BRA[0]

BRA[4]

ARA[2]

BRA[6]

ARA[1]

BRA[9]

ARA[14]

BRBA1

+1.5V_DDR

/ARCLK0

ARDQS3

R716

240

1%

ARDQ[24-31]

TP701

C725

0.1uF

ARDQM1

+1.5V_DDR

ARCKE

BRCLK1

/ARDQS0

R720 1K 1%

ARDQ[8-15]

+1.5V_DDR

BRDQM0

R714 100 5%

ARBA1

ARDQM3

BRDQS1

/ARDQS2

ARDQM2

R730 1K 1%

ARBA0

RVREF_D

A_RVREF1

R709 1K 1%

C720

0.1uF

BRDQ[24-31]

R724 1K 1%

C726

0.1uF

ARDQ[0-7]

ARDQ[16-23]

BRA[14]

R729 1K 1%

BRDQS2

R728 1K 1%

BRDQS3

RVREF_A

ARCLK1

B_RVREF6

BRA[14]

ARCLK0

ARA[0-13]

A_RVREF4

ARDQS1

B_RVREF7

ARBA1

R715

100

5%

ARODT

C719

0.1uF

R705 1K 1%

BRDQS3

C754

0.1uF

BRDQM3

BRDQ[0-7]

BRREST

BRA[0-14]

B_RVREF5

BRDQS0

B_RVREF6

+1.5V_DDR

TP700

ARDQM0

/ARCAS

C722

0.1uF

R706 1K 1%

ARBA2

RVREF_D

ARDQS3

BRDQ[16-23]

ARA[0-13]

/ARCAS

+1.5V_DDR

C753

0.1uF

/ARWE

/BRDQS2

ARDQM2

R711

240

1%

+1.5V_DDR

/BRCS

+1.5V_DDR

/BRRAS

+1.5V_DDR

RVREF_B

BRBA1

BRBA2

R732 1K 1%

/BRWE

/ARCLK0

R733 1K 1%

R713 100 5%

R721 1K 1%

R722 1K 1%

R726 1K 1%

+1.5V_DDR

/BRDQS0

+1.5V_DDR

ARBA1

BRDQM0

C751

0.1uF

C717

0.1uF

BRDQS0

BRDQM1

BRCLK1

ARDQ[8-15]

ARA[0-14]

BRA[0-13]

C745

0.1uF

ARDQS1

ARDQM0

R727 1K 1%

ARDQ[16-23]

BRBA2

ARREST

+1.5V_DDR

C757

0.1uF

/BRDQS1

BRBA0

/BRCAS

+1.5V_DDR

B_RVREF8

RVREF_C

/BRCS

/BRCLK0

BRBA0

BRCLK0

/ARCS

C752

0.1uF

/ARCS

/ARDQS0

+1.5V_DDR

B_RVREF5

BRDQM1

ARDQ[24-31]

+1.5V_DDR

BRBA0

/BRCLK0

/BRDQS1

BRDQ[24-31]

BRODT

ARREST

/ARWE

ARDQ[0-7]

+1.5V_DDR

/ARDQS3

/ARDQS1

/BRCLK1

/BRDQS3

ARBA2

BRA[0-13]

A_RVREF1

/ARWE

R717

240

1%

R712 100 5%

/ARCLK1

ARDQS2

A_RVREF3

ARCLK1

C723

0.1uF

BRDQM3

ARDQS0

ARDQM1

AVDD3V3_MEMPLL

RVREF_C

C755

0.1uF

C727

0.1uF

+1.5V_DDR

BRDQ[0-7]

+1.5V_DDR

R723 1K 1%

BRREST

ARBA2

A_RVREF2

R707 1K 1%

C721

0.1uF

R718 1K 1%

/BRCS

/BRRAS

C724

0.1uF

/ARCLK1

/BRCAS

ARCKE

R731 1K 1%

BRREST

ARCKE

RVREF_B

+1.5V_DDR

B_RVREF8

BRDQ[16-23]

B_RVREF7

ARODT

R725 1K 1%

/ARDQS2

R704 1K 1%

/ARRAS

BRODT

BRCKE

BRODT

ARBA0

ARCLK0

C756

0.1uF

BRDQ[8-15]

/ARCAS

ARDQM3

BRCKE

ARBA0

+1.5V_DDR

BRDQS1

/BRDQS0

/ARRAS

/BRWE

RVREF_A

ARDQS0

/ARDQS1

R719 1K 1%

+1.5V_DDR

C718

0.1uF

BRDQS2

C728

0.1uF

R710

240

1%

/BRWE

/BRCLK1

0.1uF

C758

BRBA1

BRDQM2

BRCKE

A_RVREF3

/ARDQS3

/ARRAS

A_RVREF2

ARA[14]

/BRCAS

ARDQS2

ARA[14]

BRCLK0

BRDQ[8-15]

R708 1K 1%

/BRDQS2

R703 1K 1%

C750

0.1uF

/BRDQS3

BRBA2

R702 1K 1%

A_RVREF4

+1.5V_DDR

ARREST

BRDQM2

ARODT

/BRRAS

/ARCS

+3.3V_NORMAL

L700

BLM18PG121SN1D

AVDD3V3_MEMPLL

C700

0.1uF

C701 10uF 10V

C704 10uF 10V

C707 10uF 10V

C708 10uF 10V

1uF

C706

1uF

C705

1uF

C703

1uF

C702

H5TQ2G63BFR-PBC

IC703

DDR_HYNIX

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

A15

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

H5TQ2G63BFR-PBC

IC701

DDR_HYNIX

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

A15

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

H5TQ2G63BFR-PBC

IC704

DDR_HYNIX

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

A15

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

H5TQ2G63BFR-PBC

IC702

DDR_HYNIX

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

A15

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

NT5CB128M16BP-DI

IC701-*1

DDR_NANYA

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12

N7

NC_6

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_7

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

NT5CB128M16BP-DI

IC703-*1

DDR_NANYA

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12

N7

NC_6

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_7

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

NT5CB128M16BP-DI

IC704-*1

DDR_NANYA

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12

N7

NC_6

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_7

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

NT5CB128M16BP-DI

IC702-*1

DDR_NANYA

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12

N7

NC_6

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_7

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

C716

0.1uF

C714

0.1uF

C715

0.1uF

C713

0.1uF

C711

0.1uF

C712

0.1uF

C710

0.1uF

C709

0.1uF

C736

0.1uF

C735

0.1uF

C734

0.1uF

C733

0.1uF

C737

0.1uF

C739

0.1uF

C740

0.1uF

C738

0.1uF

C742

0.1uF

C744

0.1uF

C743

0.1uF

C741

0.1uF

C749

0.1uF

C747

0.1uF

C748

0.1uF

C746

0.1uF

IC105

LGE2112

DDRV_44

AC1

DDRV_45

AC2

DDRV_1

A3

DDRV_2

A4

DDRV_5

B4

DDRV_8

C4

DDRV_10

D4

DDRV_4

B3

DDRV_7

C3

DDRV_46

AC3

DDRV_47

AC4

MEMTP

G10

MEMTN

G9

RVREF_B

G13

RVREF_A

G21

ARCKE

F10

ARCLK1

D9

ARCLK1

C9

ARCLK0

A20

ARCLK0

A21

ARODT

E18

ARRAS

F17

ARCAS

E17

ARCS

E16

ARWE

D14

ARRESET

B14

ARBA0

A13

ARBA1

G11

ARBA2

D16

ARCSX

F18

ARA14

C15

ARA13

A15

ARA12

F13

ARA11

C14

ARA10

F11

ARA9

E15

ARA8

D13

ARA7

B15

ARA6

E14

ARA5

F16

ARA4

E13

ARA3

B13

ARA2

A14

ARA1

F14

ARA0

F15

ARDQM0

C19

ARDQS0

C21

ARDQS0

B21

ARDQ0

C23

ARDQ1

B17

ARDQ2

D23

ARDQ3

C17

ARDQ4

D24

ARDQ5

C16

ARDQ6

C24

ARDQ7

D15

ARDQM1

D21

ARDQS1

B20

ARDQS1

C20

ARDQ8

A17

ARDQ9

A23

ARDQ10

D17

ARDQ11

B23

ARDQ12

D20

ARDQ13

D22

ARDQ14

D19

ARDQ15

C22

ARDQM2

A7

ARDQS2

B9

ARDQS2

A9

ARDQ16

C12

ARDQ17

D6

ARDQ18

B12

ARDQ19

C5

ARDQ20

C13

ARDQ21

A5

ARDQ22

A12

ARDQ23

B5

ARDQM3

E10

ARDQS3

C8

ARDQS3

D8

ARDQ24

C6

ARDQ25

D10

ARDQ26

D7

ARDQ27

C11

ARDQ28

C7

ARDQ29

C10

ARDQ30

B7

ARDQ31

B10

AVDD33_MEMPLL

N14

AVSS33_MEMPLL

N15

DVSS_50

R1

DVSS_48

P21

IC105

LGE2112

RVREF_C

P13

RVREF_D

V7

BRCLK0

F4

BRCLK0

F3

BRCLK1

V4

BRCLK1

V3

BRCKE

P6

BRODT

H6

BRRAS

H4

BRCAS

H5

BRCS

K3

BRBA0

N1

BRBA1

P5

BRBA2

K4

BRWE

L4

BRA14

L5

BRA13

M4

BRA12

N5

BRA11

M5

BRA10

P4

BRA9

M3

BRA8

L6

BRA7

L3

BRA6

N4

BRA5

K5

BRA4

N6

BRA3

N2

BRA2

M1

BRA1

N3

BRA0

K6

BRCSX

G5

DDRV_11

D5

DDRV_13

E5

DDRV_38

T5

DDRV_42

V5

DDRV_40

U5

DDRV_14

E6

DDRV_18

F6

DDRV_23

G6

DDRV_41

U6

DDRV_39

T6

DDRV_48

AC5

DDRV_19

F7

DDRV_24

G7

DDRV_49

AC6

DDRV_36

N7

DDRV_37

P7

DDRV_43

V6

DDRV_35

J10

DDRV_32

H10

DDRV_33

H13

DDRV_15

E20

DDRV_20

F20

DDRV_27

G20

DDRV_25

G15

DDRV_26

G18

DDRV_12

D25

DDRV_9

C25

DDRV_6

B25

DDRV_3

A25

DDRV_30

H7

DDRV_31

H8

DDRV_34

J8

BRDQM0

G2

BRDQS0

E4

BRDQS0

E3

BRDQ0

A1

BRDQ1

J1

BRDQ2

B2

BRDQ3

J2

BRDQ4

C2

BRDQ5

K1

BRDQ6

A2

BRDQ7

K2

BRDQM1

D1

BRDQS1

F1

BRDQS1

F2

BRDQ8

J3

BRDQ9

B1

BRDQ10

H3

BRDQ11

D3

BRDQ12

G3

BRDQ13

C1

BRDQ14

G4

BRDQ15

D2

BRDQM2

Y1

BRDQS2

V2

BRDQS2

V1

BRDQ16

T4

BRDQ17

AB4

BRDQ18

P2

BRDQ19

AB3

BRDQ20

P3

BRDQ21

AB1

BRDQ22

P1

BRDQ23

AB2

BRDQM3

U1

BRDQS3

W3

BRDQS3

W4

BRDQ24

AA3

BRDQ25

U4

BRDQ26

AA4

BRDQ27

T3

BRDQ28

Y3

BRDQ29

U3

BRDQ30

Y2

BRDQ31

U2

BRRESET

M2

DDRV_16

E23

DDRV_22

F24

DDRV_29

G24

DDRV_21

F23

DDRV_28

G23

DDRV_17

E24

DVSS_15

E12

DVSS_23

F12

DVSS_1

A18

DVSS_3

B18

DVSS_5

C18

DVSS_9

D18

DVSS_16

E19

DVSS_24

F19

DVSS_31

G19

DVSS_32

G22

DVSS_19

E25

DVSS_2

A26

DVSS_4

B26

DVSS_6

C26

DVSS_10

D26

K4B2G1646C-HCK0

IC701-*2

DDR_SS

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

K4B2G1646C-HCK0

IC703-*2

DDR_SS

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

K4B2G1646C-HCK0

IC704-*2

DDR_SS

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

K4B2G1646C-HCK0

IC702-*2

DDR_SS

A0

N3

A1

P7

A2

P3

A3

N2

A4

P8

A5

P2

A6

R8

A7

R2

A8

T8

A9

R3

A10/AP

L7

A11

R7

A12/BC

N7

A13

T3

NC_5

M7

BA0

M2

BA1

N8

BA2

M3

CK

J7

CK

K7

CKE

K9

CS

L2

ODT

K1

RAS

J3

CAS

K3

WE

L3

RESET

T2

DQSL

F3

DQSL

G3

DQSU

C7

DQSU

B7

DML

E7

DMU

D3

DQL0

E3

DQL1

F7

DQL2

F2

DQL3

F8

DQL4

H3

DQL5

H8

DQL6

G2

DQL7

H7

DQU0

D7

DQU1

C3

DQU2

C8

DQU3

C2

DQU4

A7

DQU5

A2

DQU6

B8

DQU7

A3

VREFCA

M8

VREFDQ

H1

ZQ

L8

VDD_1

B2

VDD_2

D9

VDD_3

G7

VDD_4

K2

VDD_5

K8

VDD_6

N1

VDD_7

N9

VDD_8

R1

VDD_9

R9

VDDQ_1

A1

VDDQ_2

A8

VDDQ_3

C1

VDDQ_4

C9

VDDQ_5

D2

VDDQ_6

E9

VDDQ_7

F1

VDDQ_8

H2

VDDQ_9

H9

NC_1

J1

NC_2

J9

NC_3

L1

NC_4

L9

NC_6

T7

VSS_1

A9

VSS_2

B3

VSS_3

E1

VSS_4

G8

VSS_5

J2

VSS_6

J8

VSS_7

M1

VSS_8

M9

VSS_9

P1

VSS_10

P9

VSS_11

T1

VSS_12

T9

VSSQ_1

B1

VSSQ_2

B9

VSSQ_3

D1

VSSQ_4

D8

VSSQ_5

E2

VSSQ_6

E8

VSSQ_7

F9

VSSQ_8

G1

VSSQ_9

G9

DDR ONE SIDE 12

2011.12.09

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

MT5369_TS_IN[5]

CI_TS_DATA[5]

MT5369_TS_IN[3]

CI_TS_DATA[6]

CI_TS_DATA[1]

MT5369_TS_IN[2]

CI_TS_DATA[2] CI_TS_DATA[3]

MT5369_TS_IN[0]

MT5369_TS_IN[4]

MT5369_TS_IN[1]

CI_TS_DATA[0]

CI_TS_DATA[7]

MT5369_TS_IN[7]

MT5369_TS_IN[6]

CI_TS_DATA[4]

CI_MDI[1]

CI_MDI[0]MT5369_TS_OUT[0] MT5369_TS_OUT[1] MT5369_TS_OUT[2] MT5369_TS_OUT[3] CI_MDI[3]

CI_MDI[2]

MT5369_TS_OUT[4] MT5369_TS_OUT[5] MT5369_TS_OUT[6] MT5369_TS_OUT[7] CI_MDI[7]

CI_MDI[6]

CI_MDI[5]

CI_MDI[4]

CI_A_DATA[0]

CI_MDI[6]

CI_MDI[3]

CI_MDI[7]

CI_MDI[5]

CI_MDI[2]

CI_MDI[4]

CI_MDI[1]

CI_MDI[0]

CI_A_DATA[2]

CI_A_DATA[1]

CI_A_DATA[6] CI_A_DATA[7]

CI_A_DATA[5]

CI_A_DATA[3] CI_A_DATA[4]

CI_A_DATA[0] CI_A_DATA[1] CI_A_DATA[2] CI_A_DATA[3] CI_A_DATA[4] CI_A_DATA[5] CI_A_DATA[6] CI_A_DATA[7] CI_DATA[7]

CI_DATA[6]

CI_DATA[5]

CI_DATA[4]

CI_DATA[3]

CI_DATA[2]

CI_DATA[1]

CI_DATA[0]

CI_A_ADDR[0] CI_A_ADDR[1] CI_A_ADDR[2] CI_A_ADDR[3] CI_A_ADDR[4] CI_A_ADDR[5] CI_A_ADDR[6] CI_A_ADDR[7] CI_A_ADDR[8] CI_A_ADDR[9] CI_A_ADDR[10] CI_A_ADDR[11] CI_A_ADDR[12] CI_A_ADDR[13] CI_A_ADDR[14] CI_ADDR[14]

CI_ADDR[13]

CI_ADDR[12]

CI_ADDR[11]

CI_ADDR[10]

CI_ADDR[9]

CI_ADDR[8]

CI_ADDR[7]

CI_ADDR[6]

CI_ADDR[5]

CI_ADDR[4]

CI_ADDR[3]

CI_ADDR[2]

CI_ADDR[1]

CI_ADDR[0]

MT5369_TS_OUT[0-7]

MT5369_TS_CLK

R908

47

CI_IN_TS_CLK

C902 12pF 50V OPT

MT5369_MCLKI

CI_IN_TS_SYNC

CI_TS_CLK

MT5369_MISTRT

R917

47

CI

AR901 47

CI

MT5369_MIVAL_ERR

CI_MDI[0-7]

CI_IN_TS_VAL

CI_TS_SYNC

CI_TS_DATA[0-7]

R916

47

CI

MT5369_TS_VAL

R907

47

AR900 47

CI

CI_TS_VAL

R915

47

CI

MT5369_TS_SYNC

MT5369_TS_IN[0-7]

R909

47

C900 12pF 50V

OPT

AR902

47

CI

AR903

47

CI

CI_A_ADDR[8]

/PCM_IOWR

CI_TS_CLK

R929

10K

CI

CI_IN_TS_SYNC

CI_A_ADDR[7]

+5V_CI_ON

CI_A_ADDR[2]

CI_A_ADDR[10]

/PCM_OE

R912 22

/CI_CD2

R923 10K OPT

CI_TS_DATA[0]

/CI_CD1

PCM_RST

R938

0

OPT

CI_A_ADDR[0]

C905 10uF 10V CI

R925

0

C904

0.1uF CI

R940 22

CI

/CI_CD1

R922

22

CI

PCM_INPACK

/PCM_CE1

R936

10K CI

CI_A_ADDR[5]

R928 100

CI

CI_A_ADDR[14]

CI_TS_DATA[1]

R921

22

CI

R924 10K

OPT

CI_A_DATA[0-7]

R941 22

C907

0.1uF 16V

CI

/CI_CD2

CI_MDI[0-7]

CI_VS1

/PCM_IORD

CI_A_ADDR[11]

+5V_CI_ON

+3.3V_NORMAL

R934

10K OPT

/PCM_CE1

/PCM_IOWR

CI_IN_TS_VAL CI_IN_TS_CLK

/PCM_WE

R920

22

OPT

CI_TS_DATA[3]

/PCM_WE

CI_A_ADDR[6]

CI_TS_SYNC

R942 22

CI_TS_DATA[2]

+5V_CI_ON

R910 10K CI

CI_TS_DATA[4]

R911 22

R933 10K OPT

R927

100

CI

R932 22

OPT

CI_TS_DATA[5]

PCM_RST

CI_TS_VAL

R926

0

OPT

C906 0.1uF

CI

CI_A_ADDR[9]

R939 22

CI

CI_A_ADDR[1]

/PCM_CE2

R937

10K

OPT

/PCM_IORD

CI_A_ADDR[4]

CI_A_ADDR[13]

/PCM_OE

/PCM_IRQA

CI_A_ADDR[3]

R914 10K CI

/PCM_A_REG

CI_A_ADDR[12]

+3.3V_NORMAL

CI_TS_DATA[7]

R935

10K CI

/PCM_WAIT

R93122

OPT

R906 10K OPT

CI_TS_DATA[6]

CI_DATA[0-7]

CI_A_DATA[0-7]

CI_A_ADDR[0-14]

CI_ADDR[0-14]

/PCM_WAIT

PCM_INPACK

/PCM_IRQA

CI_VS1

/PCM_REG

/PCM_CE2

/PCM_A_REG /PCM_REG

CI_A_VS1

CI_VS1

AR906 0

CI

AR907 0

CI

AR904 0

CI

AR908 0

CI

AR905 0

CI

AR909 0

CI

R919 47K CI

R930

47K

CI

R918

47K

CI

R913

47K

CI

JK900

10118309-015LF

CI

G1G2

57

TS_OUT_CLK

21

ADDR12

52

VPP

16

/IRQA

10

ADDR11

47

TS_IN0

41

TS_OUT7

5

DAT6

36

/CI_DET1

59

CI_WAIT

23

ADDR6

45

IOWR

54

TS_IN5

18

VPP

49

TS_IN2

43

VS1

13

ADDR13

7

/CARD_EN1

38

TS_OUT4

2

DAT3

25

ADDR4

56

TS_IN7

20

TS_IN_CLK

51

VCC

15

/WR_EN

9

/O_EN

46

TS_IN_SYN

40

TS_OUT6

4

DAT5

35

GND

58

CI_RESET

22

ADDR7

53

TS_IN4

17

VCC

11

ADDR10

48

TS_IN1

42

CARD_EN2

12

ADDR8

6

DAT6

37

TS_OUT3

1

GND

24

ADDR5

55

TS_IN6

19

TS_IN_VAL

50

TS_IN3

44

IORD

14

ADDR14

8

ADDR10

39

TS_OUT5

3

DAT4

26

ADDR3

60

INPACK

27

ADDR2

61

REG

28

ADDR1

62

TS_OUT_VAL

29

ADDR0

63

TS_OUT_SYN

30

DAT0

64

TS_OUT0

31

DAT1

32

DAT2

33

/IO_BIT

34

GND

65

TS_OUT1

66

TS_OUT2

67

/CI_DET2

68

GND

69

R900 10K OPT

13

2011.11.21

MID_MAIN_CI

Close to CI Slot

CI TS INPUT

Close to MT5369

Close to CI Slot

CI TS OUTPUT

Close to MT5369

CI DETECT

LGE Internal Use Only

THERMAL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

C2432

0.01uF 50V

L2407 BLM18PG121SN1D

+1.5V_DDR

+5V_NORMAL

C2415 10uF 16V

R2432

330K1/16W 5%

Q2406 MMBT3904(NXP)

E

B

C

+3.5V_ST

L2412

BLM18PG121SN1D

NON_CN

C2401

0.1uF 50V

L2405 BLM18PG121SN1D

C2422

0.01uF 50V

C2416 100pF

50V

C2406

0.1uF 16V

C2418 10uF 10V

R2433 56K

1/16W

1%

L2408 BLM18SG121TN1D

+24V

C2417 1uF 10V

R2431 15K

1/16W 5%

R2425 100

Q2407

AO3407A

G

D

S

C2412

0.1uF 16V

P2401

SMAW200-H24S2

19

12V

14

GND

9

3.5V

4

24V

18

INV ON

13

GND

8

GND

3

24V

17

12V

12

3.5V

7

GND

2

24V

16

GND/V-sync

11

3.5V

6

GND

1

PWR ON

20

A.DIM

15

GND

10

3.5V

5

GND

21

12V22P.DIM1

23

GND/P.DIM224Err OUT

25

R2419 100

Q2401

MMBT3906(NXP)

1

2

3

L2403

CIS21J121

IC2401

NCP803SN293

OPT

1

GND

3

VCC2RESET

R2435

10K

+12V

C2440

1uF 25V OPT

C2423

0.1uF

16V

+3.3V_TU_IN

L2401

CIS21J121

R2418 100

OPT

R2408

10K

R2416 100K

OPT

L2409

3.6uH

NR8040T3R6N

INV_CTL

C2429

0.1uF 16V

ERROR_OUT

R2420

0

POWER_16_GND

+3.5V_ST

L2406

3.6uH

NR8040T3R6N

R2421 10K OPT

PWM_DIM2

R2424

4.7K OPT

IC2403

TPS54319TRE

1

VIN_1

3

GND_1

7

COMP

9

SS/TR

10

PH_1

11

PH_2

12

PH_3

13

BOOT14PWRGD15EN16VIN_3

5

AGND

8

RT/CLK6VSENSE

4

GND_2

2

VIN_2

17

EP[GND]

R2413 0 5%

OPT

+3.3V_NORMAL

+12V

L2402

CIS21J121

R2417 100K

L/DIM0_VS

C2433

0.1uF 50V

C2419

0.1uF 16V

+3.5V_ST

R2423 0

POWER_16_VSYNC

C2430 22uF 10V

PANEL_CTL

C2420

0.1uF 16V

POWER_DET

IC2404

TPS54327DDAR

DEV_DCDC_TPS54327

3

VREG5

2

VFB

4

SS

1

EN

5

GND

6

SW

7

VBST

8

VIN

9

[EP]GND

C2428 3300pF 50V

+12V

+3.5V_ST

C2411

0.1uF 16V

PWM_DIM1

+3.3V_NORMAL

IC2402

NCP803SN293

1

GND

3

VCC2RESET

C2427

0.1uF 16V

R2439

10K 1%

R2426 1K

R2434

47K 1%

+24V

P2400 FW20020-24S

OPT

19

14

9

4

18

13

8

3

17

12

7

2

16

11

6

1

20

15

10

5

21 22 23 24

C2426 100pF 50V

PANEL_VCC

+3.5V_ST

C2443

0.1uF 50V

R2437 10K

A_DIM

R2422

0

POWER_24_GND

R2415

56K

1%

C2421

4700pF

50V

R2442

10K

MTK_EPI

R2441

1.8K MTK_EPI

+12V

R2430

10K

RL_ON

+3.5V_ST

C2413

0.1uF 50V

R2401

10K

C2402 10uF 16V

C2441 3300pF 50V OPT

R2403

10K

R24000

OPT

L2404

2uH

C2400 10uF 16V

POWER_ON/OFF1

R2406

10K

1%

C2403

0.1uF 16V OPT

C2404

0.1uF 16V

IC2400

AOZ1038PI

3

AGND

2

VIN

4

FB

1

PGND

5

COMP

6

EN

7

NC_1

8

NC_2

9

[EP]LX

+12V

C2414 10uF 10V

C2409 10uF 10V

C2408 10uF 10V

C2407 10uF 10V

+1.2V_MTK_CORE

L2400

BLM18PG121SN1D

C2445 22pF 50V

C2434

0.1uF 50V

+12V

+3.3V_NORMAL

C2431 10uF 16V

R2428 10K

1%

C2438 1uF 10V

C2437

0.1uF

C2442 22uF 10V

C2439 3300pF 50V

R2414 10K

C2444 22uF 10V

R2407 100K

L2411

2uH

+3.3V_NORMAL

R2427 33K 1%

L2410 BLM18PG121SN1D

IC2405

TPS54425PWPR

3

VREG5

2

VFB

4

SS

1

VO

6

PG

5

GND

7EN8

PGND1

9

PGND2

10

SW1

11

SW2

12

VBST

13

VIN1

14

VIN2

15

[EP]PGND

C2436

0.1uF 16V

POWER_ON/OFF2_1

POWER_ON/OFF1

POWER_ON/OFF2_2 POWER_ON/OFF2_3 POWER_ON/OFF2_4

POWER_ON/OFF2_1

POWER_ON/OFF2_3

POWER_ON/OFF2_2

R2402

3.3K

C2405

4700pF

50V

R2404

5.6K

1%

C24001

0.1uF 16V

R2410

2.7K 1%

R2411

1.5K 1% OPT

R2409

1.2K 1%

C2446 10uF

10V

C2447 10uF 10V

C2424 10uF 10V

C2425 10uF 10V

C2435

4.7uF 50V

C2448 10uF 10V

R2451

2K

1/8W

PANEL_DISCHARGE_REG

R2452

2K

1/8W

PANEL_DISCHARGE_REG

R2412

8.2K 5% OPT

R2442-*1

33K

MTK_NON_EPI

R2441-*1

5.6K

MTK_NON_EPI

+3.3V_NORMAL

L2413

BLM18PG121SN1D

CN

C2410

0.1uF 50V

OPT

R2405

22

POWER_24_ERROR_OUT

24

MID_POWER

2011.11.25

Vout=0.827*(1+R1/R2)=1.521V

3A

On-semi

24V-->3.48V

TYP 1450mA

#16/#20/#23 LD - GND OR USE LE(N.L.D.) - OPEN LE(L.D.) - USE

R2

FROM LIPS & POWER B/D

R2

DDR MAIN 1.5V

PANEL_POWER

R1

12V-->3.58V

Power_DET

not to RESET at 8kV ESD

ST_3.5V-->3.5V

$ 0.145

3A

+5V_Normal

Placed on SMD-TOP

*NOTE 17

R1

R2

Vout=0.8*(1+R1/R2)

4A

Vout=(0.763+0.0017*Vout.set)*(1+R1/R2)

+3.3V_NORMAL

MAX 3.4 A

R2

R1

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EEPROM_SCL

+3.5V_ST

GND

POWER_ON/OFF2_4

EDID_WP

R3023

4.7M OPT

C3004

0.1uF 16V

R3009 10K

MICOM_JAPAN

MICOM_DEBUG

SW3000

JTP-1127WEM

MICOM_RESET_SW

12

4 3

R3027

270K

OPT

R3026

10K

PANEL_CTL

SOC_RX

POWER_ON/OFF1

IR

SIDE_HP_MUTE

INV_CTL

MICOM_RESET

POWER_ON/OFF2_3

MODEL1_OPT_1

MODEL1_OPT_3

LED_B/GP4_LED_R

AMP_MUTE

AMP_RESET_N

R3022 10 K

R3006 10K

MICOM_LCD/OLED

MICOM_RESET

R3012 10K

MICOM_DIIVA

MODEL1_OPT_1

I2C_SCL3

KEY1

MODEL1_OPT_2

EXT_AMP_MUTE

I2C_SDA3

MODEL1_OPT_0

R3025 22

MICOM_DIIVA

+3.5V_ST

COMMERCIAL_12V_CTL

MODEL1_OPT_4

+3.5V_ST

MODEL1_OPT_0

SOC_RESET

12V_EXT_PWR_DET

R3007 10K

MICOM_TOUCH_KEY

POWER_ON/OFF2_1

R3008 10K

MICOM_TACT_KEY

R3010 10K

MICOM_NON_JAPAN

KEY2

SCART_MUTE

R3014 1K

MODEL1_OPT_4

+3.5V_ST

RL_ON

POWER_ON/OFF2_2

R3005 10K

MICOM_PDP

X3000

32.768KHz

R3024 22

MODEL1_OPT_3

EEPROM_SDA

MODEL1_OPT_2

HDMI_CEC

R3011 10K

MICOM_DEBUG

POWER_ON/OFF2_3

EXT_AMP_RESET

MICOM_DEBUG

C3000

0.1uF

SOC_TX

R3013 10K

MICOM_NON_DIIVA

POWER_DET

POWER_ON/OFF2_4

+3.5V_ST

HDMI_CEC

D3000

BAT54_SUZHO

R3029

120K

CEC_REMOTE

R3028 27K

+3.5V_ST

RUE003N02

Q3001

HDMI_CEC_FET_ROHM

S

D

G

EXT_AMP_RESET

SCART_MUTE

EXT_AMP_MUTE

12V_EXT_PWR_DET

COMMERCIAL_12V_CTL

R3030 10K

MICOM_GP4_10PIN

R3031 10K

MICOM_GP3_12/15PIN

+3.3V_NORMAL

R3034

4.7K OPT

+3.3V_NORMAL

R3035

4.7K OPT

+3.3V_NORMAL

Q3000 MMBT3904(NXP)

EDID_WP

E

B

C

P3000

12507WS-12L

MICOM_DEBUG

1

2

3

4

5

6

7

8

9

10

11

12

13

R3036

10K OPT

R3037

10K OPT

R3032

10K

AMP_RESET_BY_MICOM

R3033

10K

IC3000

R5F100GEAFB

MICOM

1

P60/SCLA0

2

P61/SDAA0

3

P62

4

P63

5

P31/TI03/TO03/INTP4

6

P75/KR5/INTP9/SCK01/SCL01

7

P74/KR4/INTP8/SI01/SDA01

8

P73/KR3/SO01

9

P72/KR2/SO21

10

P71/KR1/SI21/SDA21

11

P70/KR0/SCK21/SCL21

12

P30/INTP3/RTC1HZ/SCK11/SCL11

13

P50/INTP1/SI11/SDA11

14

P51/INTP2/SO11

15

P17/TI02/TO02

16

P16/TI01/TO01/INTP5

17

P15/PCLBUZ1/SCK20/SCL20

18

P14/RXD2/SI20/SDA20

19

P13/TXD2/SO20

20

P12/SO00/TXD0/TOOLTXD

21

P11/SI00/RXD0/TOOLRXD/SDA00

22

P10/SCK00/SCL00

23

P146

24

P147/ANI18

25

P27/ANI7

26

P26/ANI6

27

P25/ANI5

28

P24/ANI4

29

P23/ANI3

30

P22/ANI2

31

P21/ANI1/AVREFM

32

P20/ANI0/AVREFP

33

P130

34

P01/TO00/RXD1

35

P00/TI00/TXD1

36

P140/PCLBUZ0/INTP6

37

P120/ANI19

38

P41/TI07/TO07

39

P40/TOOL0

40

RESET41P124/XT2/EXCLKS

42

P123/XT1

43

P137/INTP0

44

P122/X2/EXCLK

45

P121/X1

46

REGC47VSS48VDD

C3002

8pF

C3003

8pF

R3000

10K

R3001 22

MICOM_DIIVA

POD_WAKEUP_N

FLG_POD_DR

/RST_DIIVA

FLG_POD_DR

/RST_DIIVA

POD_WAKEUP_N

R3002 22

MICOM_DIIVA

R3003 22

AMP_RESET_BY_MICOM

MODEL1_OPT_6

MODEL1_OPT_5

MODEL1_OPT_6

MODEL1_OPT_5

R3020 10K

MICOM_MHL

R3021 10K

MICOM_NON_MHL

R3016 10K

MICOM_GED

R3017 10K

MICOM_NON_GED

C3001 0.47uF

LOGO_LIGHT

SI1012CR-T1-GE3

Q3001-*1

HDMI_CEC_FET_VISHAY

S

D

G

R3018

3.3K

R3019

3.3K

R3005-*1

56K

MICOM_OLED_MAIN

R3005-*2

22K

MICOM_OLED_FRC

MICOM

30

For Debug

PDP

DIVA

Renesas MICOM

NON DIVA

/ OLED

MICOM MODEL OPTION

MODEL_OPT_3

LCD



For CEC

IR Wafer

10Pin

MODEL_OPT_4

12/15Pin

IR Wafer

10

MODEL_OPT_0

MODEL_OPT_1

MODEL_OPT_2

JAPAN

NON JAPAN

TOUCH_KEY

TACT_KEY

GP4 High/MID Power SEQUENCE

POWER_ON/OFF!

POWER_ON/OFF2_1

POWER_ON/OFF2_2

POWER_ON/OFF2_3

POWER_ON/OFF2_4

SOC_RESET

For Japan:LNB_INIT

HDMI_WAUP:HDMI_INIT

2011.12.12

for DiiVA

For China

(GP3_Soft touch)

NON_MHL

MHLMODEL_OPT_5

NON_GED

GEDMODEL_OPT_6

For JAPAN

GP4_HIGH

(GP4_TOOL)

For Sample Set

MICOM MODEL OPTION

Eye Sensor Option

MODEL_OPT_2

1

0

MC8101_ABOV

N/A

MODEL_OPT_4

0

1

CM3231_CAPELLA

(TACT_KEY)

(GP3 Soft touch) (GP4 Soft touch)

Don’t remove R3014, not making float P40

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

D1-_HDMI1_SOC

D0+_HDMI1_SOC

R3303 100

R3319 22

HDMI_EXT_EDID

DDC_SDA_2_JACK

R3314 100

5V_HDMI_3_JACK

R3305 1K

R3325 47K

CEC_REMOTE

D1-_HDMI2_JACK

5V_HDMI_2_JACK

R3324 47K

R3320 22

HDMI_EXT_EDID

R3316

1K

R3317 1K

HDMI_HPD_4_JACK

C3303

0.1uF 16V

JK3300

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5

D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2

D2_GND

19

HP_DET

18

5V

10

CK+

4

D1+

1

D2+

17

GND

9

D0-

8

D0_GND

3

D2-

16

DDC_DATA

7

D0+

6

D1-

15

DDC_CLK

D2+_HDMI2_JACK

+5V_NORMAL

CK-_HDMI2_JACK

D2+_HDMI4_JACK

R3326 47K

R3313 100K

C3301

0.1uF 16V

R3339 47K

D0-_HDMI4_JACK

R3337 47K

DDC_SCL_2_JACK

D2-_HDMI4_JACK

R3307

100K

5V_HDMI_2_JACK

HDMI_ARC

HDMI_HPD_2_JACK

5V_HDMI_4_JACK

R3311 1K

+5V_NORMAL

C3302

0.1uF 16V

R3338 47K

DDC_SCL_4_JACK

5V_HDMI_4_JACK

DDC_SDA_1_SOCDDC_SDA_2_JACK

D0+_HDMI4_JACK

CK+_HDMI2_JACK

R3318

4.7K

R3308 100

D1+_HDMI2_JACK

R3301 100K

R3309 100

D2+_HDMI1_SOC

CK-_HDMI1_SOC

CEC_REMOTE

C3300

0.1uF 16V

R3340 47K

JK3301

RSD-105156-100

EAG62611201

14

ARC

13

CE_REMOTE

5

D1_GND

20

BODY_SHIELD

GND

12

CK-

11

CK_GND

2

D2_GND

19

HP_DET

18

5V

10

CK+

4

D1+

1

D2+

17

GND

9

D0-

8

D0_GND

3

D2-

16

DDC_DATA

7

D0+

6

D1-

15

DDC_CLK

D0-_HDMI2_JACK

DDC_SDA_3_JACK

CK-_HDMI4_JACK

D1+_HDMI1_SOC

D0+_HDMI2_JACK

CK+_HDMI4_JACK

DDC_SCL_2_JACK

R3310

1K

DDC_SCL_4_JACK

DDC_SCL_3_JACK

CK+_HDMI1_SOC

D2-_HDMI2_JACK

HDMI_HPD_1_SOC

R3315 100

5V_HDMI_1_SOC

+5V_NORMAL

DDC_SDA_4_JACK

5V_HDMI_1_SOC

R3304 1K

DDC_SCL_1_SOC

D1+_HDMI4_JACK

R3323 47K

DDC_SDA_4_JACK

R3302 100

DDC_SCL_1_SOC

D1-_HDMI4_JACK

R3306

4.7K HDMI_INTERNAL_EDID

DDC_SDA_1_SOC

+5V_NORMAL

CEC_REMOTE

D0-_HDMI1_SOC

R3312

4.7K

EDID_WP

JK3302

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5

D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2

D2_GND

19

HP_DET

18

5V

10

CK+

4

D1+

1

D2+

17

GND

9

D0-

8

D0_GND

3

D2-

16

DDC_DATA

7

D0+

6

D1-

15

DDC_CLK

D2-_HDMI1_SOC

Q3300

MMBT3904(NXP)

E

B

C

Q3301

MMBT3904(NXP)

E

B

C

Q3302

MMBT3904(NXP)

E

B

C

IC3300

M24C02-RMN6T

HDMI_EXT_EDID

3

E2

2

E1

4

VSS

1

E0

5

SDA

6

SCL

7

WC

8

VCC

5V_HDMI_3_JACK

D0-_HDMI3_JACK

Q3303

MMBT3904(NXP)

E

B

C

CK+_HDMI3_JACK

CEC_REMOTE

HDMI_HPD_3_JACK

D2-_HDMI3_JACK

R3329 100

DDC_SDA_3_JACK

D1+_HDMI3_JACK

R3327 100K

R3336

4.7K

D1-_HDMI3_JACK

R3328 100

D2+_HDMI3_JACK

DDC_SCL_3_JACK

D0+_HDMI3_JACK

CK-_HDMI3_JACK

JK3303

RSD-105156-100

EAG62611201

14

NC

13

CE_REMOTE

5

D1_GND

20

BODY_SHIELD

12

CK-

11

CK_GND

2

D2_GND

19

HP_DET

18

5V

10

CK+

4

D1+

1

D2+

17

GND

9

D0-

8

D0_GND

3

D2-

16

DDC_DATA

7

D0+

6

D1-

15

DDC_CLK

R3331 1K

R3330

1K

R3321

4.7K HDMI_EXT_EDID

D3300

MMBD6100

A2CA1

D3302

MMBD6100

A2CA1

D3303

MMBD6100

A2CA1

D3301

MMBD6100

A2CA1

R3300

0

UI : HDMI1

UI : HDMI3

UI : HDMI2

33

HDMI 4

2011.10.29

UI : HDMI4

LGE Internal Use Only

Fiber Optic

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

JK3601

KJA-PH-0-0177

3 DETECT

4 L

5 GND

1 R

+3.3V_NORMAL

R3641

2.7K

D3615 30V OPT

C3633

18pF

50V

R3644 22

JK3602

2F11TC1-EM52-4F

C

GND

B

VCC

A

VIN

4

SHIELD

DSUB_B+

R3620

2.7K OPT

+3.3V_NORMAL

DSUB_G+

RGB_DDC_SCL

DSUB_DET

R3645

10K

RGB_EDID

DSUB_R+

R3643 22

JK3603

SLIM-15F-D-2

112233445

5

6677889

91010

111112121313141415

15

16

R3646 10K

C3615

0.1uF 16V

RGB_DDC_SDA

SPDIF_OUT

R3615

33

C3634 18pF

50V

EDID_WP

PC_R_IN

+5V_NORMAL

DSUB_HSYNC

DSUB_VSYNC

D3616 30V OPT

PC_L_IN

R3642

2.7K

RGB_5V

IC3600

M24C02-RMN6T

RGB_EDID

3

E2

2

E1

4

VSS

1

E0

5

SDA

6

SCL

7

WC

8

VCC

SOC_TX

SOC_RX

D3620

MMBD6100

A2

C

A1

R3647 100

RGB_DEBUG

D3623

5.6V OPT

D3611

5.6V OPT

D3612

5.6V OPT

D3600

20V OPT

D3601 20V OPT

D3622

5.5V

ADUC 5S 02 0R5L OPT

D3621

5.5V

ADUC 5S 02 0R5L

OPT

D3613

5.5V

ADUC 5S 02 0R5L

OPT

D3611-*1

5.6V

ESD_MTK

D3612-*1

5.6V

ESD_MTK

D3613-*1

5.5V

ADUC 5S 02 0R5L

ESD_MTK

R3602 100

RGB_DEBUG

R3600

0

NON_RGB_DEBUG

R3601

0

NON_RGB_DEBUG

RGB PC

PC AUDIO

RGB/ PC AUDIO/ SPDIF

SPDIF OUT

36

JACK HIGH / MID

2011.11.21

Closed to JACK

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

R3700

10K

HP_OUT

HP_LOUT

+3.3V_NORMAL

JK3700

KJA-PH-0-0177

EAG61030001

HP_OUT

3DETECT

4L

5GND

1R

HP_DET

HP_ROUT

VA3700

5.6V

OPT

VA3700-*1

5.6V

ESD_MTK_HP_OUT

VA3700-*2

5.6V

ESD_LG1152_HP_OUT

37

JACK_COMMON

2011.11.21

ESD for LG1152

ESD for MTK

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

AV1_R_IN

C38020.1uF

RS232

C3803

0.1uF

RS232

COMP1_Pr

+3.5V_ST

AV1_L_IN

+3.3V_NORMAL

AV1_CVBS_DET

IR_OUT

R3814

4.7K OPT

C3801

0.1uF

RS232

COMP1_DET

JK3803

SPG09-DB-009

RS232

1

2

3

4

5

6

7

8

9

10

JK3800

KJA-PH-1-0177

AV_JACK_BLACK

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

IC3800 MAX3232CDR

EAN41348201

RS232

3

C1-

2

V+

4

C2+

1

C1+

6

V-

5

C2-

7

DOUT2

8

RIN29ROUT2

10

DIN2

11

DIN1

12

ROUT1

13

RIN1

14

DOUT1

15

GND

16

VCC

R3811

4.7K OPT

COMP1_Pb

C38000.1uF

RS232

JK3801

KJA-PH-1-0177

COMP_JACK_BLACK

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

AV1_CVBS_IN

COMP1_Y

R3821

100

RS232

+3.3V_NORMAL

R3820

100

RS232

+3.5V_ST

12V_COMMERCIAL_OUT

+3.5V_ST

R3834

10K

OPT_RS232

SOC_RX

+3.5V_ST

SOC_TX

P3800

12507WS-04L

UART_4PIN_STRAIGHT

1

2

3

4

5

R3810 10K

R3806

10K

D3803

5.6V OPT

D3800

5.6V OPT

D3804

20V

OPT

D3805 20V

OPT

D3801

5.6V OPT

D3802

5.6V OPT

D3801-*1

5.6V

ESD_MTK

D3802-*1

5.6V

ESD_MTK

D3800-*1

5.6V

ESD_MTK

D3803-*1

5.6V

ESD_MTK

D3803-*2

5.6V ESD_LG1152

D3801-*2

5.6V

ESD_LG1152

D3802-*2

5.6V

ESD_LG1152

D3800-*2

5.6V

ESD_LG1152

JK3801-*1

KJA-PH-1-0177-2

COMP_JACK_GREEN

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

JK3800-*1

KJA-PH-1-0177-1

AV_JACK_YELLOW

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

P3801

12507WR-04L

UART_4PIN_ANGLE

1

2

3

4

5

RS232C

CVBS 1 PHONE JACK

COMPONENT 1 PHONE JACK

38

JACK_COMMON

2011.11.21

12V 1A FOR COMMERCIAL(RS-232C POWER)

FOR COMMERCIAL

ESD For MTK ESD For LG1152

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

IR

R4118 10K 5%

L4100

BLM18PG121SN1D

C4102

0.1uF

LED_B/GP4_LED_R

+3.5V_ST

R4105

22

COMMERCIAL_IR

C4107 100pF

50V

IR_OUT

+3.5V_ST

R4117

10K

5%

C4100

0.1uF

R4102

10K

COMMERCIAL_IR

R4108 0

COMMERCIAL_IR_US

R4113 100

KEY1

KEY2

R4123 100

EEPROM_SCL

R4124 100

R4119

47K

COMMERCIAL_IR

R4111

10K

COMMERCIAL_IR_EU

R4114 100

+3.5V_ST

C4104 1000pF 50V

+3.5V_ST

EEPROM_SDA

R4104

47K

COMMERCIAL_IR

R4100 0

IR_BYPASS

R4125 1.5K

Q4100 MMBT3904(NXP) COMMERCIAL_IR

E

B

C

Q4101

MMBT3904(NXP)

COMMERCIAL_IR

E

B

C

Q4102

MMBT3904(NXP)

COMMERCIAL_IR_EU

E

B

C

Q4104

MMBT3904(NXP)

COMMERCIAL_IR

E

B

C

R4101

1K

COMMERCIAL_IR

R4109

1K

COMMERCIAL_IR_EU

R4115

3.3K

COMMERCIAL_IR

R4103

3.3K

COMMERCIAL_IR

R4107

10K

IR_BYPASS

P4102

12507WR-10L

GP4_IR_10P

1

2

3

4

5

6

7

8

9

10

11

D4106

20V

ADUC 20S 02 010L

OPT

D4105

20V

ADUC 20S 02 010L

OPT

D4101

5.6V

AMOTECH CO., LTD.

OPT

D4100

5.6V

AMOTECH CO., LTD.

OPT

D4104

5.6V AMOTECH CO., LTD.

OPT

D4106-*1

20V

ADUC 20S 02 010L

ESD_MTK

10pF

D4105-*1

20V

ADUC 20S 02 010L

ESD_MTK

10pF

D4100-*1

5.6V

ESD_MTK

ADMC 5M 02 200L

200pF

D4101-*1

5.6V

ESD_MTK

ADMC 5M 02 200L

200pF

D4104-*1

5.6V

ESD_MTK

ADMC 5M 02 200L

200pF

D4104-*2

5.6V

ESD_LG1152

ADMC 5M 02 200L

200pF

D4101-*2

5.6V

ESD_LG1152

ADMC 5M 02 200L

200pF

D4100-*2

5.6V

ESD_LG1152

ADMC 5M 02 200L

200pF

IR & KEY

RGB Sensor

COMMERCIAL

Zener Diode is

Soft Touch Micom D/L

close to wafer

41

IR / KEY

2011.11.21

COMMERCIAL

ESD for LG1152

ESD for MTK

LGE Internal Use Only

USB D OWN STREA M

THERMAL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

USB_DM1

USB_DP2

USB_DP1

USB_DM2

C4339

10uF

10V

WIFI

USB_DM3

C4333 22uF 10V

WIFI_DP

C4327

0.1uF 16V

+5V_USB

R4339

2K

1%

WIFI_DM

R4330

0

USB_DP3

C4334 4700pF 50V

D4304

40V

SMAB34

C4322

10uF

10V

D4303

RCLAMP0502BA

OPT

C4328

0.01uF 50V

C4336

0.1uF 16V

+5V_USB_3

USB_CTL2

C4324 10uF 35V

P4301

12507WR-04L

WIFI

1

VDD

2

DM

3

DP

4

GND

5

.

C4320

0.1uF 16V

WIFI

C4321

10uF

10V

WIFI

R4329

330K

OPT

R4328

10K

JK430 3

3AU04 S-305-ZC- (LG)

1234

5

C4310

10uF

10V

JK430 2

3AU04 S-305-ZC- (LG)

1234

5

C4329

0.1uF

16V

L4302

BLM18PG121SN1D

WIFI120-ohm

C4319

0.1uF 16V

WIFI

C4326

0.1uF 50V

POWER_ON/OFF2_4

D4302

RCLAMP0502BA

OPT

+24V

/USB_OCD2

C4332 47pF 50V

IC4305

TPS54331D

3

EN

2

VIN

4

SS/TR

1

BOOT

5

VSENSE

6

COMP

7

GND

8

PH

JK430 0

3AU04 S-305-ZC- (LG)

1234

5

R4327

10K OPT

R4323

10K

USB_CTL1

L4308

6.8uH

R4336 20K

C4338 1000pF 50V

OPT

L4305

BLM18PG121SN1D

D4300

RCLAMP0502BA

OPT

/USB_OCD1

C4323

10uF

10V

+5V_USB_2

+5V_USB_3

+5V_USB_2

C4337

22uF

10V

+5V_USB

+3.3V_NORMAL

/USB_OCD3

C4301

22uF

10V

R4332

10K

POWER_ON/OFF2_4

C4331

0.1uF 16V

+12V

L4307

3.6uH

C4341

4.7uF 10V

R4342

10K

5%

L4306 BLM18PG121SN1D

USB_CTL3

C4325 10uF 16V

C4342 100pF 50V

USB_DCDC_SN1104041

IC4306-*1 BD86180MUV

DEV_USB_DCDC_BD86180

3

SS

2

COMP

4

RT

1

EN

6

CTL1

5

CTL2

7

FLG2

8

FLG1

9

USB_OUT2

10

GND_1

11

GND_2

12

USB_OUT113USB_IN_1

14

USB_IN_2

15

USB_IN_3

16

SW_1

17

SW_2

18

BST

19

PGND_1

20

PGND_2

21

VIN_1

22

VIN_2

23

GND_3

24

VREG

25

[EP]GND

C4340

4700pF

50V

USB_DCDC_SN1104041

C4340-*1

0.01uF 50V

USB_DCDC_BD86180

IC4303 TPS2554

3

IN_2

2

IN_1

4

ILIM_SEL

1

GND

5EN6

ILIM1

7

ILIM0

8

OUT_1

9

OUT_2

10

FAULT

11

[EP]

+3.3V_NORMAL

R4301

10K

R4302

10K

R4303

10K

OPT

R4304

10K

OPT

IC4306

USB_DCDC_SN1104041

SN1104041, DC-DC+2CH USB SW

3

SS

2

COMP

4

ROSC

1

EN

6

EN_SW1

5

EN_SW2

7

NFAULT2

8

NFAULT1

9

SW_OUT2

10

AGND_1

11

AGND_2

12

SW_OUT1

13

SW_IN_1

14

SW_IN_2

15

SW_IN_3

16

LX_1

17

LX_2

18

BST

19

PGND_1

20

PGND_2

21

VIN_1

22

VIN_2

23

AGND_3

24

V7V

25

[EP]GND C4300

0.1uF 16V

R4343

820

1%

R4300

27K

1/10W

R4341

27K

1/10W

OPT

R4338

10K

1%

D4300-*2

RCLAMP0502BA

ESD_LG1152

D4304-*1

40V

SX34

D4302-*1

RCLAMP0502BA

ESD_LG1152

D4303-*3

RCLAMP0502BA

ESD_LG1152

43

USB3_HUB_WiFi

2011.10.26

MAX 0.4A

From SoC

USB3

USB2

USB_WIFI

MAX 2A

Vout=0.8*(1+R1/R2)

MAX 1.5A

R1

DVR Ready

MAX 1.5A

3A

+5V_USB FOR USB1

MAX 1.8A

R2

USB1

For EMI

ESD for LG1152

ESD for MTK

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SC_L_IN

C4602 4700pF

EU

Q4601

MMBT3904(NXP)

EU

E

B

C

C4604

0.1uF

EU

JK4600

DA1R018H91E

EU

1

AUDIO_R_OUT

2

AUDIO_R_IN

3

AUDIO_L_OUT

4

AUDIO_GND

5

B_GND

6

AUDIO_L_IN

7

B_OUT

8

ID

9

G_GND

10

G_OUT

11

R_GND

12

R_OUT

13

RGB_IO

14

SYNC_GND

15

SYNC_OUT

16

SYNC_IN

17

COM_GND

18

AV_DET

19

SHIELD

SC_G

+12V

R4602 390

EU

C4603 4700pF

EU

R4603 390

EU

SC_DET

DTV/MNT_L_OUT

SC_ID

DTV/MNT_V_OUT

R4604 180

EU

SC_B

SC_R_IN

+3.3V_NORMAL

R4607 15K

EU

SC_CVBS_IN

Q4600

MMBT3906(NXP)

EU

E

B

C

C4600 1000pF 50V

EU

R4605

470

EU

C4601 1000pF 50V

EU

L4600

BLM18PG121SN1D

EU

L4601

BLM18PG121SN1D

EU

R460075

EU

DTV/MNT_R_OUT

SC_FB

SC_R

R4606 47K

EU

C4606

0.1uF 50V

EU

R4601 10K

EU

R4608

0

OPT

D4611

5.6V OPT

D4607

5.6V OPT

D4606

5.6V OPT

D4605

5.6V OPT

D4608

5.6V OPT

D4601

5.6V OPT

D4601-*1

5.6V

ESD_MTK_SCART

200pF

D4605-*2

5.6V

ESD_LG1152_SCART

200pF

D4606-*2

5.6V

ESD_LG1152_SCART

200pF

D4601-*2

5.6V

ESD_LG1152_SCART

200pF

D4611-*2

5.6V

ESD_LG1152_SCART

200pF

D4600 20V OPT

D4600-*2 20V

ESD_LG1152_SCART

10pF

C4605 100uF 16V

EU

C4607 47uF 25V

EU

D4611-*1

5.6V

ESD_MTK_SCART

200pF

D4609

5.5V OPT

D4610

5.5V OPT

D4603

5.5V OPT

D4602

5.5V OPT

D4604

5.5V OPT

D4609-*1

5.5V ESD_MTK_SCART

15pF

D4609-*2

5.5V

ESD_LG1152_SCART

15pF

D4610-*1

5.5V

ESD_MTK_SCART

15pF

D4602-*1

5.5V

ESD_MTK_SCART

15pF

D4603-*1

5.5V

ESD_MTK_SCART

15pF

D4604-*1

5.5V

ESD_MTK_SCART

15pF

D4600-*1 20V

ESD_MTK_SCART

10pF

D4605-*1

5.6V

ESD_MTK_SCART

200pF

D4606-*1

5.6V

ESD_MTK_SCART

200pF

46

SCART GENDER

2011.10.26

Full Scart(18 Pin Gender)

Gain=1+Rf/Rg

CLOSE TO JUNCTION

Rf

Rg

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

M_RFModule_ISP

M_REMOTE_RX

M_REMOTE_TX

+3.3V_NORMAL

L4800 120-ohm M_REMOTE

M_RFModule_RESET

C4800

0.1uF

P4800

12507WR-08L

M_REMOTE

1

3.3V

2

GND

3

RX

4

TX

5

RESET

6

DC

7

DD

8

GND

9

AR4800 100 1/16W

M_REMOTE

3D_SYNC_RF

ZigBee_Radio Pulse M_REMOTE OPTION

ALL M_REMOTE OPTION

48

MOTION REMOTE

2011.11.21

Only For PDP

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EPHY_RDN

C5002

0.1uF 16V

C5001

0.01uF 50V

EPHY_TDP

EPHY_TDN

C5000

0.1uF 16V

JK5000

XRJH-01A-4-DA7-180-LG(B)

LAN_XML

1

P1[CT]

2

P2[TD+]

3

P3[TD-]

4

P4[RD+]

5

P5[RD-]

6

P6[CT]

7

P7

8

P8

12

SHIELD

9

P9

11

P11

10

P10[GND]

D1

YL_C

D2

YL_A

D3

GN_C

D4

GN_A

C5003

0.01uF 50V

EPHY_RDP

LAN_JACK_POWER

D5000

5.5V OPT

D5002

5.5V OPT

D5003

5.5V OPT

D5001

5.5V OPT

D5001-*2

5.5V

ADUC 5S 02 0R5L

ESD_LG1152

D5003-*2

5.5V ADUC 5S 02 0R5L

ESD_LG1152

D5002-*2

5.5V

ADUC 5S 02 0R5L

ESD_LG1152

D5000-*2

5.5V

ADUC 5S 02 0R5L

ESD_LG1152

D5003-*1

ADUC 5S 02 0R5L

ESD_MTK

D5000-*1

ADUC 5S 02 0R5L

ESD_MTK

D5002-*1

ADUC 5S 02 0R5L

ESD_MTK

D5001-*1

ADUC 5S 02 0R5L

ESD_MTK

JK5000-*1 TLA-6T764

LAN_TDK

1

R1

2

R2

3

R3

4

R4

5

R5

6

R6

7

R7

8

R8

12

SHIELD

9

R9

11

R11

10

R10[GND]

D1

YL_C

D2

YL_A

D3

GN_C

D4

GN_A

Ethernet Block

50

LAN_VERTICAL

2011.12.09

ESD for LG1152

ESD for MTK

LGE Internal Use Only

THER MAL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

I2C_SDA1

+3.5V_ST

C5818

0.22uF 50V

SPK_R-

R5802 100

+24V_AMP

R5810 43

C5816

0.22uF 50V

L5804

10.0uH

C5813 1uF 50V

C5809

0.1uF 50V

+24V_AMP

C5810 1uF 50V

AUD_MASTER_CLK

22 R5808

C5805

0.1uF 16V

L5800

CIS21J121

C5817

0.22uF 50VR5813

43

L5801

BLM18PG121SN1D

AUD_SCK

AMP_MUTE

R5811 43

+3.3V_NORMAL

P5800

WAFER-ANGLE

1

2

3

4

SPK_L-

+3.3V_NORMAL

L5806

10.0uH

L5802

BLM18PG121SN1D

AUD_LRCK

AMP_RESET_N

C5806

0.1uF 16V

C5804

2.2uF 10V

R580922

I2C_SCL1

C5803

0.1uF 16V

SPK_L-

SPK_R+

R580722

C5812 330pF 50V

C5808

0.1uF 16V

OPT

C5811 330pF 50V

SPK_L+

AUD_LRCH

C5807

0.1uF 16V

C5821

0.22uF 50V

L5805

10.0uH

C5802

0.1uF 50V

C5800

0.1uF 50V

C5815 10uF 35V

C5820

0.22uF 50V

R5801 10K

R5800

10K

SPK_L+

R5812 43

L5803

10.0uH

C5819

0.22uF 50V

+24V

C5814

0.1uF 50V

SPK_R-

Q5800 MMBT3904(NXP)

E

B

C

C5826 10uF 10V

C5827 10uF 35V

C5828

0.1uF 16V

C5829 1000pF 50V OPT

C5801

0.1uF 16V

IC5800

STA380BW

DEV_STM_AMP

1

VCC_REG

2

VSS_REG

3

OUT2B

4

GND2

5

VCC2

6

OUT2A

7

OUT1B

8

VCC1

9

GND1

10

OUT1A

11

VDD_REG

12

GND_REG

13

NC_114NC_215NC_316NC_417NC_518NC_619NC_720NC_821NC_922NC_1023NC_1124NC_12

25

NC_13

26

NC_14

27

NC_15

28

VDDDIG1

29

GNDDIG1

30

FFX3A

31

FFX3B

32

EAPD/FFX4A

33

TWARNEXT/FFX4B

34

VREGFILT

35

AGNDPLL

36

MCLK

37

BICKI38LRCKI

39

SDI

40

RESET

41

PWDN

42

INTLINE

43

SDA44SCL

45SA46

TESTMODE

47

GNDDIG248VDDDIG2

49

[EP]

C5822 1000pF 50V

C5823 1000pF 50V

C5824 1000pF 50V

C5825 1000pF 50V

GP4_MT5369

58

2011.11.21

AUDIO[ST]

0X38

SPEAKER_L

0x38 when SA=0

SPEAKER_R0x3A when SA=1

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SIGN600005

SCART_Rout

SCART_MUTE

SCART_Lout

DTV/MNT_R_OUT

R6012

4.7K

OPT

+12V

C6005

33pF

EU

R6010

470K

OPT

R6008 33K

EU

+3.5V_ST

C6004

0.1uF 50V

EU

R60002.2K

EU

L6000

EU

R6002

470K

OPT

Q6000

MMBT3904(NXP)

EU

E

B

C

R6011

2.2K

EU

DTV/MNT_R_OUT

C6003

33pF

EU

DTV/MNT_L_OUT

Q6001

MMBT3904(NXP)

EU

E

B

C

DTV/MNT_L_OUT

R600433K

EU C6002 6800pF

OPT

C6007

6800pF

OPT

C6008

1uF 25V

EU

C6000 1uF 25V EU

IC6000

AZ4580MTR-E1

EU

3

IN1+

2

IN1-

4

VEE

1

OUT1

5

IN2+

6

IN2-

7

OUT2

8

VCC

SCART_AMP_R_FB

SCART_AMP_L_FB

R6013

510

EU

[SCART AUDIO MUTE]

AUD_OUT >> EU/CHINA_HOTEL_OPT

60

SCART AUDIO AMP

2011.11.21

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

HP_ROUT_MAIN

R6100

4.7K

HP_LOUT_AMP

R6104

OPT

100K

R6105

4.7K

HP_ROUT_AMP

C6104 1uF 10V

SIDE_HP_MUTE

+3.3V_NORMAL

R6106 0

OPT

R6102

4.7K OPT

+3.3V_NORMAL

R6107 1K

HP_LOUT_MAIN

L6100

120-ohm BLM1 8PG121 SN1D

R6103

4.7K

C6105 10uF 10V

IC6100 TPA6132A2

EAN60724701

3

INR+

2

INL+

4

INR-

1

INL-

5

OUTR

6G07G18

HPVSS

9

CPN

10

PGND

11

CPP

12

HPVDD

13EN14

VDD15SGND16OUTL

C6107

0.1uF 16V

R6101

OPT

Q6100

MMBT3904(NXP)

E

B

C

C6100 1uF 10V

C6103 1uF

10V

C6108

2.2uF 10V

C6106

2.2uF 10V

C6109

2.2uF 10V

Close to the IC

From Micom

EARPHONE AMP

2011.09.29

HEADPHONE AMP

61

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Q6201

AO3407A

CI

G

D

S

+5V_CI_ON

C6207

4.7uF 10V

OPT

R6218 10K

CI

+5V_NORMAL

C6202

0.1uF 16V

OPT

R6242

2.2K CI

R6221 10K OPT

PCM_5V_CTL

R6248 10K

CI

R6223

4.7K

CI

R6241 22K

CI

Q6200 MMBT3904(NXP) CI

E

B

C

C6210 1uF 25V OPT

C6210-*1 1uF 25V

CI_MTK

CI POWER ENABLE CONTROL

62

CI SLOT

2011.10.31

Option FOR MTK

Option FOR LG1152

LGE Internal Use Only

THERMAL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

FE_TS_DATA[5]

FE_TS_DATA[4]

FE_TS_DATA[2]

FE_TS_DATA[6] FE_TS_DATA[7]

FE_TS_DATA[1]

FE_TS_DATA[0]

FE_TS_DATA[3]

C6526

0.1uF 16V

+5V_TU

C6519 10uF

10V

DVB_S&CHB

C6536

22uF

10V

C6522

0.1uF 16V

+3.3V_D_Demod

C6531

0.1uF

C6532

0.1uF 16V

LNB_TX

L6502

BLM18PG121SN1D

T2/C&CN&BR

C6544

0.1uF 16V

L9_T2/C/S

C6512 100pF

DVB_S&CHB

/S2_RESET

CHB_DATA

L6503

BLM18PG121SN1D

CHB_SYNC

C6516

0.1uF 16V

T2/C&CHB&CN&BR

IF_AGC

I2C_SCL4

R6509

33

L6501

BLM18PG121SN1D

DVB_S&CHB

C6506 18pF 50V

OPT

C6514

0.1uF 16V

I2C_SDA4

C6517 18pF 50V

OPT

+5V_TU

C6548

0.1uF 16V

+5V_NORMAL

I2C_SDA6

+3.3V_TU

+1.8V_TU

L6507

BLM18PG121SN1D

CHB

C6501 10uF 10V

CHB

+5V_TU

L6506

BLM18PG121SN1D

NOT_T/C&AT

C6546 10uF 10V

R6510

33

IF_P

+5V_TU

C6530

0.1uF 16V

R6504 22

DVB_S&CHB

C6523 100pF 50V

CHB

CHB_CLK

R6503 22

DVB_S&CHB

C6529

22uF

10V

C6525

0.1uF 16V

OPT

C6524 100pF

OPT

R6518 82

C6507 100pF 50V

T2/C&CHB&CN&BR

R6527 20K 1%

NOT_T/C&AT

C6515

0.1uF DVB_S&CHB

R6525 0

NOT_L9_T2/C/S

L6508

BLM18PG121SN1D

CHB

+3.3V_D_Demod

RF_SWITCH_CTL

C6528 10uF

6.3V

OPT

R6531 1

C6513 4700pF 50V

CN

C6518 18pF 50V

OPT

R6529 10K 1%

NOT_T/C&AT

R6523 10K

TU_TS_ERR

+1.23V_TU

+5V_NORMAL

+3.3V_D_Demod

C6511 100pF 50V

+3.3V_TU

R6506

100

T/C&AT&CHB

+1.23V_TU

C6539

0.1uF 16V

R6528 11K 1%

NOT_T/C&AT

C6508 18pF 50V

OPT

+3.3V_TU

C6509

0.1uF 16V CHB

TU_CVBS

C6520

0.1uF

16V

MTK/L9_DVB/ATSC/NTSC

+1.23V_TU

TU_TS_VAL

C6538 10uF

10V

NOT_T/C&AT

+3.3V_TU

TU_TS_VAL

CHB_VAL

/TU_RESET

L6500

BLM18PG121SN1D

FE_TS_VAL

FE_TS_DATA[0-7]

+3.3V_TU_IN

R6515

4.7K

FE_TS_CLK

0.1uF

C6540

R6519

1K

OPT

R6508 100

MTK/L9_DVB/ATSC/NTSC

IC6503

AZ1117BH-1.8TRE1

1

ADJ/GND

2

OUT

3

IN

C6542

0.1uF

NOT_T/C&AT

+3.3V_TU

C6510 1000pF 50V

CN

+1.8V_TU

R6500 0

RF_SWITCH

TU_TS_ERR

TUNER_SIF

C6549 10uF

16V

NOT_T/C&AT

I2C_SCL6

C6527

0.1uF OPT

+3.3V_TU

CHB_ERR

IC6501

AP2132MP-2.5TRG1

EAN61387601

NOT_T/C&AT

3

VIN

2

EN

4

VCTRL

1

PG

5

NC

6

VOUT

7

ADJ

8

GND

9

[EP]

C6503

0.1uF 16V

RF_SWITCH

C6533

10uF 16V

NOT_T/C&AT

LNB_OUT

IF_N

FE_TS_SYNC

CHB_CVBS

R6513 10

DVB_S&CHB

R6512

2.2K

OPT

C6505

0.1uF 16V

+3.3V_D_Demod

R6511 100K

OPT

C6521

0.1uF OPT

+3.3V_NORMAL

+1.8V_TU

C6500

0.1uF 16V

L9 ATSC

C6534

22uF

10V

LNB_OUT

LNB_TX

CHB_CVBS

CHB_ERR

CHB_SYNC

CHB_VAL CHB_CLK

CHB_DATA

ATV_OUT

C6535 1uF OPT

IC6500

74LVC1G08GW

L9_T2/C/S

3

GND

2

A

4

Y

1B5

VCC

R6526 100

L9_T2/C/S

1/16W 5%

AR6502 0

NOT_T/C&AT&CHB

AR6500 0

NOT_T/C&AT&CHB

AR6501 0

NOT_T/C&AT&CHB

R6516

470

Q6500 MMBT3906(NXP)

E

B

C

Q6501 MMBT3906(NXP)

E

B

C

R6532 0

NOT_L9_BR_TW_CN Tuner

C6550

0.1uF

16V

C6551 100pF 50V

TU6500-*1 TDSS-H151F

AT_H/NIM_V

5

+B1[3.3V]

11

DIF[N]

2

RESET

10

DIF[P]

4

SDA

1

NC

9

IF_AGC

8

CVBS

3

SCL

7

+B2[1.8V]

6

SIF

12

SHIELD

TU6500

TDSS-G151D

T/C_H/NIM_V

5

+B1[3.3V]

11

DIF[N]

2

RESET

10

DIF[P]

4

SDA

1

NC

9

IF_AGC

8

CVBS

3

SCL

7

+B2[1.8V]

6

SIF

12

SHIELD

TU6503

TDSQ-G051D

T/C/S2_V

1

N.C_1

2

RESET

3

SCL

4

SDA

5

+3.3V_TUNER

6

SIF

7

+1.8V_TUNER

8

CVBS

9

T/C_IF_AGC

10

T/C_DIF[P]

11

T/C_DIF[N]

12

N.C_2

13

N.C_3

14

N.C_4

15

GND_1

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

GND_2

29

GND_3

30

+1.23V_S2_DEMOD

31

S2_RESET

38

SHIELD

32

+3.3V_S2_DEMOD

33

S2_F22_OUTPUT

34

S2_SCL

35

S2_SDA

36

LNB

37

GND_4

TU6502

TDSQ-H051F

CHB_V

1

+5V[SPLITTER]

2

RESET

3

TU_SCL

4

TU_SDA

5

M_+3.3V

6

M_SIF

7

M_+1.8V

8

M_CVBS

9

M_IF_AGC

10

M_DIF[P]

11

M_DIF[N]

12

S_3.3V

13

S_1.8V

14

S_CVBS

15

GND_1

16

SD_ERROR

17

SD_SYNC

18

SD_VALID

19

SD_MCLK

20

SD_SERIAL_D0

21

N.C_1

22

N.C_2

23

N.C_3

24

N.C_4

25

N.C_5

26

N.C_6

27

N.C_7

28

GND_2

29

GND_3

30

SD_1.23V_DEMOD

31

SD_RESET

36

SHIELD

32

SD_3.3V_DEMOD

33

N.C_8

34

SD_SCL

35

SD_SDA

TU6503-*1 TDSQ-G351D

T2/C/S2

1

N.C_1

2

RESET

3

SCL

4

SDA

5

+B1[3.3V]

6

SIF

7

+B2[1.8V]

8

CVBS

9

N.C_2

10

N.C_3

11

N.C_4

12

+B3[3.3V]

13

+B4[1.23V]

14

N.C_5

15

GND_1

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

GND_2

29

GND_3

30

+B5[1.23V]

31

S2_RESET

38

SHIELD

32

+B6[3.3V]

33

S2_F22_OUTPUT

34

S2_SCL

35

S2_SDA

36

LNB

37

GND_4

TU6501-*1 TDSN-B051F

BR_F/NIM_V

1

RF_S/W_CTL

2

RESET

3

SCL

4

SDA

5

+B1[3.3V]

6

SIF

7

+B2[1.8V]

8

CVBS

9

NC_1

10

NC_2

11

NC_3

12

+B3[3.3V]

13

+B4[1.23V]

14

NC_4

15

GND

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

SHIELD

TU6504 TDSH-T151F

TW_H/NIM

5

+B1[3.3V]

11

DIF[N]

2

RESET

10

DIF[P]

4

SDA

1

RF_S/W_CTL

9

IF_AGC

8

CVBS

3

SCL

7

+B2[1.8V]

6

SIF

12

SHIELD

TU6501

TDSN-G351D

T2/C_F/NIM_DEV

1

NC_1

2

RESET

3

SCL

4

SDA

5

+B1[3.3V]

6

SIF

7

+B2[1.8V]

8

CVBS

9

NC_2

10

NC_3

11

NC_4

12

+B3[3.3V]

13

+B4[1.23V]

14

NC_5

15

GND

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

SHIELD

C6508-*1 68pF 50V

BR_TW_CN_TUNER

C6506-*1 68pF 50V

BR_TW_CN_TUNER

R6500-*1

1K 5%

BR_TW_CN_TUNER

R6508-*1

1K 5%

BR_TW_CN_TUNER

R6532-*1

BLM18PG121SN1D

L9/BR_TW_CN_TUNER

120-ohm

R6528-*1 12K

1/16W 1%

CN

R6521

220

R6520 220

TU6501-*3 TDSN-C051D

CN_LG3921

1

RF_S/W_CTL

2

RESET

3

SCL

4

SDA

5

+B1[3.3V]

6

SIF

7

+B2[1.8V]

8

CVBS

9

NC_1

10

NC_2

11

NC_3

12

+B3[3.3V]

13

+B4[1.23V]

14

NC_4

15

GND

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

SHIELD

TU6501-*2 TDSN-C251D

CN_ATBM

1

RF_S/W_CTL

2

RESET

3

SCL

4

SDA

5

+B1[3.3V]

6

SIF

7

+B2[1.8V]

8

CVBS

9

NC_1

10

NC_2

11

NC_3

12

+B3[3.3V]

13

+B4[1.23V]

14

NC_4

15

GND

16

ERROR

17

SYNC

18

VALID

19

MCLK

20

D0

21

D1

22

D2

23

D3

24

D4

25

D5

26

D6

27

D7

28

SHIELD

65

TUNER

2011.11.21

T2 : Max 1.7A

150mA(MAX)

close to TUNER

Vout=0.6*(1+R1/R2)

2. No via on both of them

Ground Width >= 24mils

1. should be guarded by ground

ERROR & VALID PIN

close to TUNER

RF_SWITCH_CTL USE: T2/C,T/C,ATSC,DTMB.ISDB-T

3. Signal Width >= 12mils

R2

2A

465mA(MAX)

should be guarded by groumd

T/C/S & H/NIM & T2/C TUNER(EU & CHINA)

R1

Signal to Signal Width = 12mils

else : Max 240mA

2012 perallel because of derating

else : Max 0.7A

CHB : Max 480mA

T/C_H/NIM

T/C/S2 T2/C_F/NIM T2/C/S2 CHB

AT_H/NIM

CN

CHB

CN

DVB_S DVB_ST/C&AT&CHB T/C&AT&CHB

DVB_S&CHB DVB_S&CHB DVB_S&CHB

NOT_T/C&AT

RF_SWITCH

T2/C

T2/C&CN

T2/C&CHB&CN

T2/C&CN

T2/C&CHB&CN

T/C&AT&CHB

Close to the tuner

close to TUNER

close to Tuner

Seperate GND for CHB

T/C&AT&CHB

T2/C&CHB&CN

NOT_T/C&AT&CHBNOT_T/C&AT&CHB

NOT_T/C&AT&CHB

H/NIM&CHB

NOT_DVB_S

BR

L9_T2/C/S

Not_L9_T2/C/S

Not_L9_T2/C/S Not_L9_T2/C/S

Not_L9_T2/C/S

LGE Internal Use Only

THERMAL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

A_GND

LNB_OUT

DCDC_GND

A_GND

R6901 33

LNB

A_GND

+12V

LNB_TX

L6900

33UH

SP-7850_33

LNB

R6900 33

LNB

C6907 0.22uF

LNB

A_GND

C6902 1uF

50V LNB

+12V_LNB

DCDC_GND

C6906

68uF

35V

LNB

A_GND

I2C_SDA4

C6905 22000pF

LNB

I2C_SCL4

A_GND

R6903

4.7K

LNB

D6901

40V

LNB_SMAB34

C6900

0.22uF 25V

LNB

C6901

0.01uF 50V

LNB

D6903

40V

LNB_SMAB34

L6901

BLM18PG121SN1D

LNB

IC6900

A8290SETTR-T

LNB

1

BOOST

3

TCAP

7

TDI

9

VREG

10

SDA11ADD12SCL

13

NC_2

14

IRQ

15

NC_3

16

NC_4

17

NC_5

18

NC_6

19

BFC

20

NC_7

21

NC_8

22

BFO23NC_924BFI25VIN26LX27GNDLX28LNB

5

TDO

8

GND

6

EXTM

4

NC_1

2

VCP

29

[EP]

C6908 27pF

OPT

C6903 0.1uF

LNB

C6909

27pF

OPT

D6902

40V

LNB_SMAB34

A_GND

+3.3V_NORMAL

DCDC_GND

A_GND

+12V_LNB

A_GND

C6911

0.1uF 50V

LNB

C6904

0.1uF 50V

LNB

C6912

68uF

35V LNB

D6900

30V

MBR230LSFT1G

LNB

R6906

2.2K 1W LNB

D6904

LNB

C6910 10uF 25V LNB

R6904 0

R6905 0

C6916 18pF

LNB

C6915 18pF

OPT

C6913 33pF OPT

C6914 33pF

LNB

D6901-*1

40V

LNB_SX34

D6902-*1

40V

LNB_SX34

D6903-*1

40V

LNB_SX34

C6917

0.1uF 50V LNB

C6918

0.1uF 50V

LNB

(Option:LNB)

DVB-S2 LNB Part Allegro

DCDC_GND and A_GND are connected in pin#27

3A

Max 1.3A

PCB_GND and A_GND are connected

Input trace widths should be sized to conduct at least 3A

2A

DCDC_GND and A_GND are connected

2.4A

close to Boost pin(#1)

Ouput trace widths should be sized to conduct at least 2A

close to VIN pin(#25)

69

LNB

2011.11.21

Close to Tuner Surge protectioin

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EXT_AMP_MUTE

AUDIO_L_OUT_COMMERCIAL

C7005

0.1uF 50V

+24V

+12V

C7004

0.1uF 50V

R7000 1K

COMMERCIAL_12V_CTL

R7001 100

IC7000

MP5000DQ

3

ENABLE/FAULT

2

DV/DT

4

I-LIMIT

1

GND

5

NC

6

SOURCE_1

7

SOURCE_2

8

SOURCE_3

9

SOURCE_4

10

SOURCE_5

11

VCC

P7000

12507WR-12L

1

2

3

4

5

6

7

8

9

10

11

12

13

AUDIO_R_OUT_COMMERCIAL

EXT_AMP_RESET

12V_COMMERCIAL_OUT

SPK_L_OUT_COMMERCIAL

SPK_R_OUT_COMMERCIAL

L7000

BLM18PG121SN1D

JK7000

KJA-PH-0-0177

EAG61030001

COMMER_EXT_AMP_JACK

3DETECT

4L

5GND

1R

SPK_R_OUT_COMMERCIAL

SPK_L_OUT_COMMERCIAL

Q7001 MMBT3904(NXP)

E

B

C

12V_EXT_PWR_DET

+3.5V_ST

C7002 22uF 25V

R7005 22K

R7004 100K

R7006 10K

C7003 22uF 25V

C7000 470pF 50V

C7001 1uF 25V

L7001

BLM18PG121SN1D

D7000

5.6V

D7001

5.6V

C7007 10uF 16V

C7006 10uF 16V

70

COMMERCIAL_OPTION

2011.11.21

FOR AMP RESET (MAIN SOC)

FOR 12V CONTROL (FROM MICOM)

FOR COMMERCIAL 12V OUT RS-232C 9 PIN (OPT:COMMER_EXT_12V)

FOR COMMERCIAL AUDIO OUT (OPT:COMMER_EXT_AMP)

AUDIO OUT JACK (OPT:COMMER_EXT_AMP)

PATTERN SHOULD BE CONSIDERED (MAX 3W)

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

TXC3N

TXACLKN

C7102

0.1uF 50V

OPT

TXA0N

C7100 10uF 16V

OPT

TXC2N

TXCCLKP

TXA1P

TXBCLKN

PANEL_VCC

TXA2P

TXD3N

TXC2P

TXC4N

TXCCLKN

TXD4N

R7100 33 LGD_2D/3D_CTRL

R7103 10K

BIT_SEL_LOW

TXB1P

TXB2P

TXB0N

TXA4N

TXB4P

TXBCLKP

TXC0P

TXC1N

TXD2N

TXA1N

L7100 BLM18SG121TN1D LVDS_51PIN

TXB1N

TXA3P

TXD0P

R7104 33

AUO_2D/3D_CTRL

TXD1P

TXA2N

TXA4P

TXD3P

TXB0P

TXB2N

TXB3N

TXA3N

TXC4P

R7102 10K

LVDS_SEL_LOW

TXDCLKN

R7101

3.3K LVDS_SEL_HIGH

TXC1P

2D/3D_CTL

TXACLKP

2D/3D_CTL

TXB4N

TXA0P

TXB3P

TXC0N

TXD1N

+3.3V_NORMAL

TXD4P

TXDCLKP

TXD0N

TXC3P

C7101 1000pF 50V

OPT

TXD2P

P7100

FI-RE51S-HF-J-R1500

LVDS_51PIN

1

NC

2

NC

3

NC

4

NC

5

NC

6

AUO_65_MIRROR

7

LVDS_SEL

8

NC

9

NC

10

L/DIM_ENABLE

11

GND

12

RA0N

13

RA0P

14

RA1N

15

RA1P

16

RA2N

17

RA2P

18

GND

19

RACLKN

20

RACLKP

21

GND

22

RA3N

23

RA3P

24

RA4N

25

RA4P

26

GND

27

BIT_SEL

28

RB0N

29

RB0P

30

RB1N

31

RB1P

32

RB2N

33

RB2P

34

GND

35

RBCLKN

36

RBCLKP

37

GND

38

RB3N

39

RB3P

40

RB4N

41

RB4P

42

GND

43

GND

44

GND

45

GND

46

GND

47

NC

48

VLCD

49

VLCD

50

VLCD

51

VLCD

52

GND

P7101

FI-RE41S-HF-J-R1500

LVDS_41PIN

1

NC

2

NC

3

NC

4

NC

5

NC

6

NC

7

NC

8

NC

9

GND

10

RC0N

11

RC0P

12

RC1N

13

RC1P

14

RC2N

15

RC2P

16

GND

17

RCCLKN

18

RCCLKP

19

GND

20

RC3N

21

RC3P

22

RC4N

23

RC4P

24

GND

25

GND

26

RD0N

27

RD0P

28

RD1N

29

RD1P

30

RD2N

31

RD2P

32

GND

33

RDCLKN

34

RDCLKP

35

GND

36

RD3N

37

RD3P

38

RD4N

39

RD4P

40

GND

41

GND

42

GND

I2C_SDA1

I2C_SCL1

R7105 33

CP_BOX

R7106 33

CP_BOX

PWM_DIM1

OPC_EN

R7108

33

LGD_32/37_LVDS_OPC

R7107 33

LGD_32/37_LVDS_PWM

BIT_SEL

[51Pin LVDS OUTPUT Connector]

[41Pin LVDS OUTPUT Connector]

LVDS

LVDS_SEL

71

LVDS_HIGH_MID

2011.08.11

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

I2C_SCL1

L/DIM0_SCLK

R7601 10K L/DIM_OUT

+3.3V_NORMAL

L/DIM0_MOSI

R7607

4.7K L/DIM_OUT

R7606 33

L/DIM_OUT

P7600

12507WR-08L

L/DIM_OUT

1

2

3

4

5

6

7

8

9

I2C_SDA1

L/DIM0_VS

R7600 10K OPT

AR7600

33

1/16W

L/DIM_OUT

LOCAL DIMMING

[To LED DRIVER]

76

LOCAL DIMMING

2011.12.13

LGE Internal Use Only

THERMAL

THERM AL

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

VCOM_N

MCLK

DISCHG

R7709 0

1/16W

R7743 0

1/16W

OPT

SWP

EO

C7750 1uF 25V OPT

C7714 10uF 25V

Vcore

C7757 1uF 50V

VGH

GIP_RST

CLK3

R7701 10K

1/16W

VCOMRFB

VCOM

CLK5_I

VCOM_N

GST

R7745

0

1/16W

VCOM_P

C7731

0.1uF 16V

GMA14

VGH_F

R7741 0

1/16W OPT

CTRLP

CLK1_I

VCOM_LOOP

VDD

VGH

VL

SWP

R7736 3K 1/16W

VCOMLFB

R7708

0

1/16W

C7705 10uF 10V

R7726 0 1/16W OPT

VCC

R7706

47

1/16W

CLK2_I

VGL

VCC

CTRLP

TH7700

47k-ohm

NCP18WB473F10RB

I2C_SDA2

GMA12

VDD

GCLK

R7732 0 1/16W OPT

C7716 10uF 25V

OPT

VGL_I

REVERSE

C7740 1000pF 50V

OPT

C7755 1uF 50V

CLK2

SWN

VST

VDD

GMA7

C7723 10uF 25V

C7713 10uF 25V

CLK6

R7710 0

1/16W

C7748

1uF25V

C7745

1uF25V

R7721 0 1/16W

C7747

1uF25V

R7733 0 1/16W

COMP

VCC

R7746 0

1/16W

C7721 10uF

25V

OPT

C7709 10uF 10V

CLK2_I

VGL

COMP

R7716 0 1/16W OPT

R7731 0

1/16W

SWN

VDD

R7723 0 1/16W

CLK4_I

R7742 3K

1/16W

OPT

CLK3_I

RE

R7718

9.1K 1/16W

R7735 100 1/16W

CTRLN

C7717 15pF 50V

R7724

0

1/16W

OPT

C7707 10uF 10V OPT

VGL

VCOM_LOOP

R7704

47

1/16W

GMA4

CLK6_I

R7713

2.2

1/16W

OPT

C7711 10uF 10V

CLK6_I

L7702

22uH

VDD

VGH

SS

MCLK

DISCHG

R7703

47

1/16W

L7700

LQM2HPN2R2MG0L

2.2uH

CLK4

R7722 100K 1/16W 1%

SS

VL

H_VDD

C7725 10uF 25V OPT

C7720 15pF 50V

VGH_R

VGL

R7719 0

1/16W

C7746

1uF25V

CLK1

C7736 1000pF 50V

CLK5_I

CLK5

TCOMP

EO

CLK1_I

VCC18

C7706 10uF 10V

L7701

LQM2HPN2R2MG0L

2.2uH

VCOM_P

PANEL_VCC

VGL

CLK4_I

C7719 15pF 50V

R7734

0

1/16W OPT

C7704

0.1uF 16V

GCLK

C7729 1000pF

50V OPT

R7705 47

1/16W

R7740 0

1/16W

I2C_SCL2

C7742 1uF 25V

GMA5

C7718 15pF 50V

RE

CTRLN

VGH_EVEN

L7704

22uH

GST

C7710 10uF 10V

TCOMP

PANEL_VCC

GMA15

CLK3_I

VGH_ODD

REVERSE

GST_SOC

GCLK_SOC

EO_SOC

MCLK_SOC

C7726 1uF 25V

PANEL_VCC

R7738 0 1/16W

R7747 0 1/16W OPT

VCC

R7749 1K 1/16W OPT

R7748 1K 1/16W

R7751 15K 1/16W

R7752 15K 1/16W

R7754 15K 1/16W OPT

R7753 15K 1/16W OPT

C7708 10uF 10V OPT

R7700

2K

1/16W

R7725

0

1/16W

OPT

C7724

1uF 25V

VCOM_DYN

R7720 47K

1/16W

5%

R7717 33K 1/16W

VGH_FB

VGL_FB

L7703

NR6020T6R8NC

6.8uH

C7715 10uF 16V

C7722 10uF 16V

R7729

2.7K

1/16W

VCC

R7728 100K

1/16W 5%

R7730

1/16W

OPT

R7737

1/16W

OPT

VGL_FB

R7739

1.5K 1/16W 5%

R7727 100K

1/16W 5%

VGH_FB

R7707

0

R7714

0

R7702

0

R7715

0

R7712

0

R7711

0

C7744 1uF 50V

C7749 1uF 50V

PMIC_RESET

D7703

100V

1N4148W

D7705

100V

1N4148W

Q7701

MMBT3906(NXP)

EBC

D7704

100V

1N4148W

D7706

100V

1N4148W

C7728 10uF 10V OPT

C7712 1uF 10V

C7741 10uF 16V

EPI_LOCK6

EPI_LOCK6_SOURCE

+3.3V_NORMAL

C7732

0.1uF 50V

C7727

0.1uF 50V

C7754

0.1uF 50V

Q7700

MMBT3904(NXP)

EBC

D7700

40V

SX34

D7701

40V

SX34

Q7702

MMBT3904(NXP)

E

B

C

Q7703

MMBT3904(NXP)

E

B

C

R7758

10K R7756 10K

R7757

10K

C7743 1uF 25V

C7756 1uF 25V

R7759

0

1/16W

R7760

0

1/16W

GMA18

VST

TXA1P

GMA1

EPI_LOCK3

CLK2

GIP_RST

VDD

TXB0P

CLK4

Vcore

GMA4

TXB2N

VCOMRFB

TXACLKP

VGL_I

GMA3 GMA4

EPI_LOCK3

CLK1

GMA16

GMA3

VGH_ODD

CLK1

GMA12

GMA9

Z_OUT

TXB2P

VGH_EVEN

CLK6

GMA9

VGH_EVEN

TXB1P

GMA5

GMA15

TXACLKN

GMA7

C7702

0.01uF 50V

GMA10

C7703

0.1uF 50V

VGH_ODD

VCC18

Vcore

VGL_I

GMA18

VCOM

GMA7

TXB0N

H_VDD

GMA14

GMA10

VDD

TXA4N

CLK4

CLK5

CLK6

VGH_F

TXA1N

H_VDD

CLK3

VGH_R

Z_OUT

VST

GMA15

VCOMLFB

CLK5

CLK2

GMA16

VCOM

GMA5

GMA14

EPI_LOCK6_SOURCE

CLK3

TXB1N

VCC18

GMA12

VGH_F

GIP_RST

VGH_R

GMA1

TXA4P

C7700

0.01uF 50V

C7701

0.1uF 50V

R7744 20K 1/10W 5%

R7750 20K 1/10W 5%

C7733 10uF 16V

R7755

100

P7702

FL8S050HA1

DEV_50WAFER

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

P7703

FL8S050HA1

DEV_50WAFER

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

C7730 68uF 35V

C7735 68uF 35V

C7734

0.1uF 50V

C7737

0.1uF 50V

C7739

0.1uF 50V

C7738

0.1uF 50V

R7761 10K OPT

VCC18

IC7700

TPS65178RSLR

EPI

1

OUT4

2

SWB4

3

RST

4

OUT1

5

OUT2

6

SWB2

7

PGND2

8

SWB1_1

9

SWB1_2

10

NC

11

PVINB1_1

12

PVINB1_2

13

AVIN

14

PVINB3

15

SWB316OUT3

17

PGND3

18

PGND_119PGND_2

20

SW_121SW_2

22

SWI23SWO

24

AGND

25

SS

26

COMP

27

SCL

28

SDA

29

VL

30

TCOMP

31

CTRLP

32

VGH

33

SWP

34

SWN

35

VGL

36

CTRLN

37

GMA138GMA239GMA340GMA441GMA542GMA643VCOM44NEG45POS46VCOMFB47DYN48PGND4

49

[EP]AGND

IC7701

TPS65198

EPI

1

CLK13CLK3

7

RE

9

VGH_F

10

ODD

11

EVEN

12

VST

13

RESET

14

DISCHG

15

VGL

16

VGH117VGH2

18

OUT19NEG20POS

21

AVDD

22

GND

23

VSENSE

24

EO

25

GST

26

MCLK

27

GCLK

28

BI-SCAN

5

CLK5

8

VGH_R

6

CLK64CLK42CLK2

29

[EP]VGL

D7702

40V

OPT

L7705 BLM18PG121SN1D OPT

T-Con

77

2011.12.01

FROM SOC

TO SOC

INSTEAD OF AMCC0208

INSTEAD OF AMCC0209

[Right Source(41PIN LOCATION)]

[Left Source(51PIN LOCATION)]

THIS IS REVERSE PATTERN !!!!

FROM SOC

CH6

CH5

CH4

FROM SOC

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EMMC_DATA[5]

EMMC_DATA[0]

EMMC_DATA[2]

EMMC_DATA[1]

EMMC_DATA[4]

EMMC_DATA[7]

EMMC_DATA[3]

EMMC_DATA[6]

DAT4

DAT6

EMMC_RST

3.3V_EMMC

DAT5

DAT4

DAT5

C8104

0.1uF 16V

R8116

10K

DAT3

EMMC_CMD

C8103

2.2uF 10V

EMMC_VCCQ

EMMC_DATA[0-7]

C8106

2.2uF 10V

EMMC_VCCQ

C8107 10pF 50V

OPT

DAT6

C8102

0.1uF 16V

DAT3

R8117

10K

C8105

0.1uF 16V

EMMC_CLK

IC8100-*1

H26M21001ECR

HYNIX_EMMC_2GB

DAT0

A3

DAT1

A4

DAT2

A5

DAT3

B2

DAT4

B3

DAT5

B4

DAT6

B5

DAT7

B6

CLK

M6

CMD

M5

NC_3

A6

NC_4

A7

NC_23

C5

NC_42

E5

NC_43

E8

NC_44

E9

NC_45

E10

NC_52

F10

NC_58

G3

NC_59

G10

NC_66

H5

NC_73

J5

NC_80

K6

NC_81

K7

NC_82

K10

NC_116

P7

NC_119

P10

RESET

K5

VCCQ_1

C6

VCCQ_2

M4

VCCQ_3

N4

VCCQ_4

P3

VCCQ_5

P5

VCC_1

E6

VCC_2

F5

VCC_3

J10

VCC_4

K9

VDDI

C2

VSS_1

E7

VSS_2

G5

VSS_3

H10

VSS_4

K8

VSSQ_1

C4

VSSQ_2

N2

VSSQ_3

N5

VSSQ_4

P4

VSSQ_5

P6

NC_1

A1

NC_2

A2

NC_5

A8

NC_6

A9

NC_7

A10

NC_8

A11

NC_9

A12

NC_10

A13

NC_11

A14

NC_12

B1

NC_13

B7

NC_14

B8

NC_15

B9

NC_16

B10

NC_17

B11

NC_18

B12

NC_19

B13

NC_20

B14

NC_21

C1

NC_22

C3

NC_24

C7

NC_25

C8

NC_26

C9

NC_27

C10

NC_28

C11

NC_29

C12

NC_30

C13

NC_31

C14

NC_32

D1

NC_33

D2

NC_34

D3

NC_35

D4

NC_36

D12

NC_37

D13

NC_38

D14

NC_39

E1

NC_40

E2

NC_41

E3

NC_46

E12

NC_47

E13

NC_48

E14

NC_49

F1

NC_50

F2

NC_51

F3

NC_53

F12

NC_54

F13

NC_55

F14

NC_56

G1

NC_57

G2

NC_60

G12

NC_61

G13

NC_62

G14

NC_63

H1

NC_64

H2

NC_65

H3

NC_67

H12

NC_68

H13

NC_69

H14

NC_70

J1

NC_71

J2

NC_72

J3

NC_74

J12

NC_75

J13

NC_76

J14

NC_77

K1

NC_78

K2

NC_79

K3

NC_83

K12

NC_84

K13

NC_85

K14

NC_86

L1

NC_87

L2

NC_88

L3

NC_89

L12

NC_90

L13

NC_91

L14

NC_92

M1

NC_93

M2

NC_94

M3

NC_95

M7

NC_96

M8

NC_97

M9

NC_98

M10

NC_99

M11

NC_100

M12

NC_101

M13

NC_102

M14

NC_103

N1

NC_104

N3

NC_105

N6

NC_106

N7

NC_107

N8

NC_108

N9

NC_109

N10

NC_110

N11

NC_111

N12

NC_112

N13

NC_113

N14

NC_114

P1

NC_115

P2

NC_117

P8

NC_118

P9

NC_120

P11

NC_121

P12

NC_122

P13

NC_123

P14

EMMC_CLK_BALL

EMMC_CMD_BALL

EMMC_CLK_BALL

EMMC_RESET_BALL

EMMC_VDDI

DAT5

AR8100 22 1/16W

AR8101 22 1/16W

AR8102 22

R8100 10K

R8101 10K

R8102 10K

R8103 10K

R8104 10K

R8105 10K

R8106 10K

R8107 10K

IC8100-*3

H26M31001EFR

DEV_HYNIX_EMMC_4GB

DAT0

A3

DAT1

A4

DAT2

A5

DAT3

B2

DAT4

B3

DAT5

B4

DAT6

B5

DAT7

B6

CLK

M6

CMD

M5

NC_3

A6

NC_4

A7

NC_23

C5

NC_42

E5

NC_43

E8

NC_44

E9

NC_45

E10

NC_52

F10

NC_58

G3

NC_59

G10

NC_66

H5

NC_73

J5

NC_80

K6

NC_81

K7

NC_82

K10

NC_116

P7

NC_119

P10

RESET

K5

VCCQ_1

C6

VCCQ_2

M4

VCCQ_3

N4

VCCQ_4

P3

VCCQ_5

P5

VCC_1

E6

VCC_2

F5

VCC_3

J10

VCC_4

K9

VDDI

C2

VSS_1

E7

VSS_2

G5

VSS_3

H10

VSS_4

K8

VSSQ_1

C4

VSSQ_2

N2

VSSQ_3

N5

VSSQ_4

P4

VSSQ_5

P6

NC_1

A1

NC_2

A2

NC_5

A8

NC_6

A9

NC_7

A10

NC_8

A11

NC_9

A12

NC_10

A13

NC_11

A14

NC_12

B1

NC_13

B7

NC_14

B8

NC_15

B9

NC_16

B10

NC_17

B11

NC_18

B12

NC_19

B13

NC_20

B14

NC_21

C1

NC_22

C3

NC_24

C7

NC_25

C8

NC_26

C9

NC_27

C10

NC_28

C11

NC_29

C12

NC_30

C13

NC_31

C14

NC_32

D1

NC_33

D2

NC_34

D3

NC_35

D4

NC_36

D12

NC_37

D13

NC_38

D14

NC_39

E1

NC_40

E2

NC_41

E3

NC_46

E12

NC_47

E13

NC_48

E14

NC_49

F1

NC_50

F2

NC_51

F3

NC_53

F12

NC_54

F13

NC_55

F14

NC_56

G1

NC_57

G2

NC_60

G12

NC_61

G13

NC_62

G14

NC_63

H1

NC_64

H2

NC_65

H3

NC_67

H12

NC_68

H13

NC_69

H14

NC_70

J1

NC_71

J2

NC_72

J3

NC_74

J12

NC_75

J13

NC_76

J14

NC_77

K1

NC_78

K2

NC_79

K3

NC_83

K12

NC_84

K13

NC_85

K14

NC_86

L1

NC_87

L2

NC_88

L3

NC_89

L12

NC_90

L13

NC_91

L14

NC_92

M1

NC_93

M2

NC_94

M3

NC_95

M7

NC_96

M8

NC_97

M9

NC_98

M10

NC_99

M11

NC_100

M12

NC_101

M13

NC_102

M14

NC_103

N1

NC_104

N3

NC_105

N6

NC_106

N7

NC_107

N8

NC_108

N9

NC_109

N10

NC_110

N11

NC_111

N12

NC_112

N13

NC_113

N14

NC_114

P1

NC_115

P2

NC_117

P8

NC_118

P9

NC_120

P11

NC_121

P12

NC_122

P13

NC_123

P14

DUMMY_1

DU1

DUMMY_2

DU2

DUMMY_3

DU3

DUMMY_4

DU4

DUMMY_5

DU5

DUMMY_6

DU6

DUMMY_7

DU7

DUMMY_8

DU8

DUMMY_9

DU9

DUMMY_10

DU10

DUMMY_11

DU11

DUMMY_12

DU12

DUMMY_13

DU13

DUMMY_14

DU14

DUMMY_15

DU15

DUMMY_16

DU16

IC8100-*2

KLM2G1HE3F-B001

SAMSUNG_EMMC_2GB

DAT0

A3

DAT1

A4

DAT2

A5

DAT3

B2

DAT4

B3

DAT5

B4

DAT6

B5

DAT7

B6

CLK

M6

CMD

M5

NC_3

A6

NC_4

A7

NC_23

C5

NC_42

E5

NC_43

E8

NC_44

E9

NC_45

E10

NC_52

F10

NC_58

G3

NC_59

G10

NC_66

H5

NC_73

J5

NC_80

K6

NC_81

K7

NC_82

K10

NC_116

P7

NC_119

P10

RSTN

K5

VDD_1

C6

VDD_2

M4

VDD_3

N4

VDD_4

P3

VDD_5

P5

VDDF_1

E6

VDDF_2

F5

VDDF_3

J10

VDDF_4

K9

VDDI

C2

VSS_1

C4

VSS_2

E7

VSS_3

G5

VSS_4

H10

VSS_5

K8

VSS_6

N2

VSS_7

N5

VSS_8

P4

VSS_9

P6

NC_1

A1

NC_2

A2

NC_5

A8

NC_6

A9

NC_7

A10

NC_8

A11

NC_9

A12

NC_10

A13

NC_11

A14

NC_12

B1

NC_13

B7

NC_14

B8

NC_15

B9

NC_16

B10

NC_17

B11

NC_18

B12

NC_19

B13

NC_20

B14

NC_21

C1

NC_22

C3

NC_24

C7

NC_25

C8

NC_26

C9

NC_27

C10

NC_28

C11

NC_29

C12

NC_30

C13

NC_31

C14

NC_32

D1

NC_33

D2

NC_34

D3

NC_35

D4

NC_36

D12

NC_37

D13

NC_38

D14

NC_39

E1

NC_40

E2

NC_41

E3

NC_46

E12

NC_47

E13

NC_48

E14

NC_49

F1

NC_50

F2

NC_51

F3

NC_53

F12

NC_54

F13

NC_55

F14

NC_56

G1

NC_57

G2

NC_60

G12

NC_61

G13

NC_62

G14

NC_63

H1

NC_64

H2

NC_65

H3

NC_67

H12

NC_68

H13

NC_69

H14

NC_70

J1

NC_71

J2

NC_72

J3

NC_74

J12

NC_75

J13

NC_76

J14

NC_77

K1

NC_78

K2

NC_79

K3

NC_83

K12

NC_84

K13

NC_85

K14

NC_86

L1

NC_87

L2

NC_88

L3

NC_89

L12

NC_90

L13

NC_91

L14

NC_92

M1

NC_93

M2

NC_94

M3

NC_95

M7

NC_96

M8

NC_97

M9

NC_98

M10

NC_99

M11

NC_100

M12

NC_101

M13

NC_102

M14

NC_103

N1

NC_104

N3

NC_105

N6

NC_106

N7

NC_107

N8

NC_108

N9

NC_109

N10

NC_110

N11

NC_111

N12

NC_112

N13

NC_113

N14

NC_114

P1

NC_115

P2

NC_117

P8

NC_118

P9

NC_120

P11

NC_121

P12

NC_122

P13

NC_123

P14

C8100

0.1uF 16V

OPT

IC8100

SDIN5D2-4G-974L1

SANDISK_EMMC_4GB

DAT0

A3

DAT1

A4

DAT2

A5

DAT3

B2

DAT4

B3

DAT5

B4

DAT6

B5

DAT7

B6

CLK

M6

CMD

M5

NC_3

A6

NC_4

A7

NC_23

C5

NC_42

E5

NC_43

E8

NC_44

E9

NC_45

E10

NC_52

F10

NC_58

G3

NC_59

G10

NC_66

H5

NC_73

J5

NC_80

K6

NC_81

K7

NC_82

K10

NC_116

P7

NC_119

P10

RESET

K5

VCCQ_1

C6

VCCQ_2

M4

VCCQ_3

N4

VCCQ_4

P3

VCCQ_5

P5

VCC_1

E6

VCC_2

F5

VCC_3

J10

VCC_4

K9

VDDI

C2

VSS_1

E7

VSS_2

G5

VSS_3

H10

VSS_4

K8

VSSQ_1

C4

VSSQ_2

N2

VSSQ_3

N5

VSSQ_4

P4

VSSQ_5

P6

NC_1

A1

NC_2

A2

NC_5

A8

NC_6

A9

NC_7

A10

NC_8

A11

NC_9

A12

NC_10

A13

NC_11

A14

NC_12

B1

NC_13

B7

NC_14

B8

NC_15

B9

NC_16

B10

NC_17

B11

NC_18

B12

NC_19

B13

NC_20

B14

NC_21

C1

NC_22

C3

NC_24

C7

NC_25

C8

NC_26

C9

NC_27

C10

NC_28

C11

NC_29

C12

NC_30

C13

NC_31

C14

NC_32

D1

NC_33

D2

NC_34

D3

NC_35

D4

NC_36

D12

NC_37

D13

NC_38

D14

NC_39

E1

NC_40

E2

NC_41

E3

NC_46

E12

NC_47

E13

NC_48

E14

NC_49

F1

NC_50

F2

NC_51

F3

NC_53

F12

NC_54

F13

NC_55

F14

NC_56

G1

NC_57

G2

NC_60

G12

NC_61

G13

NC_62

G14

NC_63

H1

NC_64

H2

NC_65

H3

NC_67

H12

NC_68

H13

NC_69

H14

NC_70

J1

NC_71

J2

NC_72

J3

NC_74

J12

NC_75

J13

NC_76

J14

NC_77

K1

NC_78

K2

NC_79

K3

NC_83

K12

NC_84

K13

NC_85

K14

NC_86

L1

NC_87

L2

NC_88

L3

NC_89

L12

NC_90

L13

NC_91

L14

NC_92

M1

NC_93

M2

NC_94

M3

NC_95

M7

NC_96

M8

NC_97

M9

NC_98

M10

NC_99

M11

NC_100

M12

NC_101

M13

NC_102

M14

NC_103

N1

NC_104

N3

NC_105

N6

NC_106

N7

NC_107

N8

NC_108

N9

NC_109

N10

NC_110

N11

NC_111

N12

NC_112

N13

NC_113

N14

NC_114

P1

NC_115

P2

NC_117

P8

NC_118

P9

NC_120

P11

NC_121

P12

NC_122

P13

NC_123

P14

DUMMY_1

DU1

DUMMY_2

DU2

DUMMY_3

DU3

DUMMY_4

DU4

DUMMY_5

DU5

DUMMY_6

DU6

DUMMY_7

DU7

DUMMY_8

DU8

DUMMY_9

DU9

DUMMY_10

DU10

DUMMY_11

DU11

DUMMY_12

DU12

DUMMY_13

DU13

DUMMY_14

DU14

DUMMY_15

DU15

DUMMY_16

DU16

R8103-*1 47K

R8104-*1 47K

R8105-*1 47K

R8106-*1 47K

R8100-*1 47K

R8102-*1 47K

R8107-*1 47K

R8101-*1 47K

11.09.29

81

eMMC

eMMC I/F

Don’t Connect Power At VDDI

(Just Interal LDO Capacitor)

EMMC DATA LINE 47K PULL/UP

EMMC DATA LINE 10K PULL/UP

LGE Internal Use Only

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

+3.5V_ST

L8900

BLM18PG121SN1D

LOGO_LIGHT

P8900

12507WR-03L

LOGO_LIGHT

1

2

3

4

Q8900 MMBT3904(NXP)

LOGO_LIGHT

E

B

C

LOGO_LIGHT

R8903

1K

LOGO_LIGHT

+3.5V_ST

R8901

10K

LOGO_LIGHT

R8902

10K

OPT

C8900

0.1uF 16V

LOGO_LIGHT

R8900

22

LOGO_LIGHT

Place Near Micom

LGE Internal Use Only

2012 LED/LCD TV Engineering guide

< Applicable Model > XXLM760S-ZB

LGE Internal Use Only

◈ CONTENT ◈

New features Main PCBs Block Diagrams, IIC Map Structure of TV set and connection of sub ass’ys New sub ass’ys

- Instruction of new sub ass’ys

- How to use tool

- Download Adjust way of new features (widevine…) Repair guide The latest issue and concerning issue

LGE Internal Use Only

EPI Interface

EPI(Embedded Point-Point Interface) Features

• Point-Point topology (support 2 Pair option)

• CDR (Clock Data Recovery)

• Bandwidth up to 1.85Gbps/pair

at FHD 120Hz 10 bit application

• Lock signal cascading and feedback to T-Con

• Embedded Control Data

Merits

• Better reliability on common noise

• No data skew and better EMI margin

• Fewer lines than mini-LVDS

• Slim PCB design

TCON

2

LOCK

VCC

1

Figure1. Topology

LGE Internal Use Only

EPI Interface (mini-LVDS vs. EPI)

Comparison

HF mini-LVDS

What to change

EPI (Embedded clock P-to-P Interface)

-Difficult to upgrade bandwidth limit

-Multiple number of wires needed for higher bandwidth

HF mini-

LVDS

FHD (10bit)

60Hz 120Hz 240Hz

No. of Signal 36 36 72

Connector

60pin

(2ea)

60pin

(2ea)

80pin

(2ea)

-Better reliability on common noise

-No data skew. Better EMI margin

-Lower cost ( Cable, Connector )

-Slim S-PCB design (14mm Æ 10mm) helps slimmer TV

EPI

FHD (10bit)

60Hz 120Hz 240Hz

960ch 960ch 720ch

No. of Signal 12 12 32

Connector -

50 pin

(2ea)

70pin

(2ea)

LCM (T-con to S-Driver IC)

TCON

2

LOCK

VCC

1

TCON

18

VCC

1

18

HF mini-LVDS

EPI

* Bandwidth Capability

- FHD 120Hz 10Bit : 594Mbps@36Lines → 1.65Gbps@12Lines

- FHD 240Hz 10Bit : 594Mbps@72Lines → 1.25Gbps@32Lines

(FHD 120Hz)

LGE Internal Use Only

HF mini-LVDS EPI

Topology

Protocol

Features

@10bit, FHD120

• Multi Drop

• Data rate: 660Mbps

• External clock

• Point to Point

• Data rate : 1.8Gbps

• Embedded cl ock, Control

Merit

• Simple structure

• Standardization

• Fewer Lines : 12

• Embedded cl ock

: low EMI, Clock skew free

• Easy to PCB design

Demerit

• Too many lines : 36

• Clock skew

• EMI due to clock lin es

• Bandw idth limit

• Transmission Overhead

: 4bit delimiter

TCON

Lock

2

1

TCON

EPI Interface (mini-LVDS vs. EPI)

LGE Internal Use Only

Main PCB for Broadband

Main + TCON all in one

To PSU

1

2

6

4

1

Main processor, DDR Memory eMMC Memory

2

3

4

Micom for Key/IR sensing

PMIC

Audio AMP (10W+10W)

xxLM760S-ZB

Soft touch +IR

Front Spk

To module

5

EPI Wafer

G/S

model

2

1

LNB IC

Only G/S model

1

2

Chassis : LD22E PCB P/No : EAX64307905

3

6

Level shifter

WIFI

RF Assy

LGE Internal Use Only

MTK5369 Block Diagram( LM76 )

L/R In

SPDIF OUT

USB

Audio

AMP

(NTP7500

or STA)

I2S Out

MTK

CI slot

P_TS

CVBS

P_TS

T/C Demod

IF(+/-)

USB1

RS-232C

PC-RGB

PC-AUDIO

OPTIC

LAN

SYSTEM

DDR3 X

1600 X 16

(2Gb)

HDMI1 HDMI2

HDMI3

Side

Rear

RGB,H/V

Ethernet

CVBS

UART

SYSTEM EEPROM X 1

(256Kb)

HDMI

MUX

(HDCP

EEPROM)

M-Remote

Module

Air/ Cable

TUNER

(T/C)

TUNER

(S2)

DIGITAL DEMOD

(T/C)

DVB-S

ANALOG

DEMOD

DIGITAL DEMOD

(S2)

TS_S/P

LNB

USB2 USB3

HDMI4

LVDS

41P

51P

eMMC X 1

(4GB)

USB_WIFI

SYSTEM

DDR3 X

1600 X 16

(2Gb)

DDR

CONTROLER A/B

SPI

LOCAL DIMMING

I2C

Sub Micom

(RENESASA)

IR

Remote Control

SYSTEM

DDR3 X

1600 X 16

(2Gb)

SYSTEM

DDR3 X

1600 X 16

(2Gb)

UART

P_TS

Power load

EPI

50P 50P

X_TAL 27MHz

LGE Internal Use Only

Jack Interface

[PR0P],[PB0P],[Y0P] [OPCTRL8]

[VDACX_OUT] [VDACY_OUT]

[AUOUTL0]

[ADIN0_SRV]

[CVBS2P]

[AIN0_L_ADDC] [AIN0_R_AADC]

[SPDIF_OUT]

[AUOUTR0]

Main SoC

MTK

[SOY0]

[Y1P],[PB1P],[PR1P] [OPCTRL9]

[AL0_ADAC]

[AR0_ADAC

[VGA_SCL]

[VGA_SDA]

[OPCTRL7]

[VSYNC], [HSYNC]

[RP],[GP],[BP]

[ASPDIF0]

SPDIF

SPDIF_OUT

[AIN2_L_AADC]

COMP 1 PHONE JACK

COMP1_Y/Pb/Pr COMP1_DET

SC_DET

SC_R/G/B +

SC_ID

DTV/MNT_V_OUT

DTV/MNT_L_OUT

IC6000

AZ4580M

SC_L/R_IN

SC_CVBS_IN

[SCART_LOUT]

[SCART_ROUT]DTV/MNT_R_OUT

SC_FB

[AIN3_R_AADC]

[AIN3_L_AADC]

[CVBS0P]

[OPCTRL5]

AV1_L_IN AV1_R_IN

AV1_CVBS_DET

AV1_CVBS_IN

CVBS 1 PHONE JACK

EARPHONE

JACK

HP_LOUT_MAIN

HP_ROUT_MAIN

RGB_PC

RGB_DDC_SCL

RGB_DDC_SDA

DSUB_DET

DSUB_VSYNC, DSUB_HSYNC

DSUB_R+, DSUB_G+, DSUB_B+

PC AUDIO

PC_L_IN PC_R_IN

[AIN2_R_AADC]

Full Scart(18 Pin Gender)

IC6100

TPA6132A2

HP_LOUT_AMP

HP_ROUT_AMP

LGE Internal Use Only

GP4 Backend block diagram (EPI & T-con)

IC7700

TPS65178

IC7701

TPS65198

50Pin

EPI LEFT

50Pin

EPI RIGHT

VCOM, GIP_RST

R(0옴)

OPT

DISCHG

VGL_I

VGH_ODD, VGH_EVEN

VGH_R, VGH_F, VST

R

(0옴)

CLK1~6_I

CLK1~6

VCOM_P/N/LOOP

VGL_FB

CTRLN

VCC

CTRLP

VGH_FB

VDD

SWP

SWN

Main

SoC

MTK

R

(47옴)

EO_SOC

MCLK_SOC

GST_SOC

GCLK_SOC

GCLK

MCLK

GST

EO

[TCON6] [TCON5] [TCON4] [TCON3]

LGE Internal Use Only

GP4 Backend block diagram (EPI & T-Con)

Main SoC

MTK

IC7700

TPS65178

50Pin

EPI LEFT

50Pin

EPI RIGHT

GMA[1][3][9][10][12][14][15][16][18]

GMA[4][5][7][12][15]

EPI_LOCK3

TXA1N/P, TXACLKN/P, TXA4N/P

EPI

CH1/2/3

EPI

CH4/5/6

TXA0N/P, TXB1N/P, TXB2N/P

Z_OUT

Vcore

VDD

H_VDD

Vcore

H_VDD

VDD

VCC18

VCOMLFB

VCOMRFB

EPI_LOCK6

EPI_LOCK6_SOURCE

VCOM_DYN

PMIC_RESET

I2C_SDA2 I2C_SCL2

[TCON7]

[TCON8] [OPCTRL11] [OPCTRL10]

LGE Internal Use Only

GP4 Backend block diagram (LVDS Tx & Local Dimming)

LVDS Tx

Block

Main SoC

MTK

LVDS_SEL

BIT_SEL_LOW

51Pin LVDS

Output

PANEL_VCC

(+12V)

41Pin LVDS

Output

10-bit (R)

Dual-link LVDS Output

24

10-bit (R)

24

Dual-link LVDS Output

• LVDS_SEL : “H”=JEIDA, “L” or NC=VESA (LGD)

• BIT_SEL : “H” or NC = 10-bit, “L” = 8-bit

L/DIMO_SCLK

L/DIMO_MOSI

I2C_SCL1

I2C_SDA1

L/DIMO_VS

[LDM_CK]

[LDM_VSYNC]

[STB_SCL]

[LDM_D0]

[STB_SDA]

LGE Internal Use Only

Interconnection - 1

1

Main PCB

2

Power Board

3

Tact key PCB

T-con Driver

1

2

3

4

5

Main / LPB 24Pin cable Main / Module EPI cable

50& 50PIN LED driver / PSU

10Pin (IR+Touch) Cable

SPK Cable

Local Dimming Cable

[PCBs]

[Cables]

6

12

3

1

2

3

4

5

6

xxLM760S-ZA

7

RF Assy Cable

7

8

WIFI Assy Cable

8

45

4

RF Assy

5

WIFI Assy

LGE Internal Use Only

2012Y IR + Soft touch PCB Pinmap

Circuit Block Diagram

Pin Configuration

KEY1, KEY2 Voltage (Tolerance of voltage ±0.2V)

Ass’y Picture

LGE Internal Use Only

2012Y IR + Soft Touch LED Lighting Scenario

구분

Spec

내용

비고

Power

Indicator UI

- 12Y GP4 High(L9), GP4 Mid(MTK), GP4 Low(S7LR2)

Æ

“ Power Light” UI Delete compare d with 11Y(GP3 model)

- 11Y Carry Over Model : 12Y same Power LED scenario process

Æ

“ Power Light “ UI Delete, The way of 11Y Soft Touch Ass’yis used. White LED Disable

-

GP4

(High/Mid/Low)

Power LED

Scenario

User

Condition

Power On

- Stand-By condition to Red LED On : After DC ON, Red LED light Blinks twice and then Red LED is Off

- Stand-By condition to Red LED Off : After DC ON, Red LED light Blinks three times and then Red LED is Off

-

Power Off

- Without Blink, Red LED On immediately But, If the mode of Power Indicator UI is Stand-By, keep staying Red LED Off status

-

Remote Key

input

- When you put the remote Control button, Red LED Blinks once -

Warm

Stand-by

- Red LED On stays and In the case of Set On, Red LED turns Off

Æ Including DVR Ready model, Japanese model

Same as the

11Y

3D mode - Red LED Off (Power On condition is identical)

Same as the

11Y

Factory

Condition

Factory Default

Mode

(In-Stop)

- 12Y LED Model : Stand-By On (Red LED On)

- 12Y CCFL Model : Stand-By On (Red LED On)

- 11Y Carry Over Model (CS5XX/CM5XX) : Stand-By On (Red LED On)

- After In-Stop, Red LED On is processed and after In-Stop, Red LED turns on within 3 sec

-

Power Only

Mode

- In the case of Power Only On, Red LED turns Off

- In the case of DC Off, Red LED turns On

-

Power LED Scenario

LGE Internal Use Only

Introductions of GP4 Sensor (Touch IC)

Touch Key Threshold Level (Ta = 25ºC )

1. Verify the number of THR at first.

2. Once you correctly touch Touch button for more than 1 sec, you can see a Touch data while you keep touching the button.

3. Keep in mind that you can only read the Touch data during touch status.

4. It doesn’t matter that Touch data gets low value after taking off your finger.

Manual of Touch Sensitivity

LGE Internal Use Only

Introductions of GP4 Sensor (Touch IC)

Touch EEPROM Register change with USB port

1. Write all of the address, value (Hex) as a below. capable of only Touch.txt file based on the left picture

2. Make the file [ Filename :

‘Touch.txt’ ] and move it to USB (The

outermost area, Don’t move it to any folder)

3. Connect USB to TV and press button ‘ADJ menu’ and then choose the ‘touch sensitivity setting’

4. Press button ‘SIMPLINK (Simply Link key)’ and then you can see the OK Pop up.

5. After that, you check it the IR LED version on In-start menu and verify it that the number of version is changed to what you want.

Addr Value

LGE Internal Use Only

Introductions of 12Y RF ass’y + Magic Remote control

LGE Internal Use Only

1. System

Remote

RF Receiver

TV

UART or USB

RF

 Pairing Information Transmission (Send to TV after Paired)

• Static Calibration Data (Bypass only)

• Remote FW ver. (Save also in Receiver)

• BD_ADDR (Save also in Receiver)

• Pairing Information Transmission Sequence

• When it is paired, the remote sends packets(pairing success, F/W version, BD_ADDR) to the receiver.

• The receiver sends the pairing success packet to TV directly.

• F/W version and BD_ADDR packets are just saved on the receiver.

• The receiver sends F/W version or BD_ADDR packet to TV when it is required.

 Motion Data Transmission

• Period : 7.5msec

• Motion Data : gyro, accelerometer

 Voice Data Transmission

• Period : 10msec

• Voice sampling : 16khz 16bit

Æ See “6-2. Packets” on page 8.

LGE Internal Use Only

2. Remote Buttons (M3 vs. M4)

BUTTON

RF Unpaired

IR_CODE

RF Paired RF_CODE

IR continuous

repeat

ETC.

Phsical

Buttons

POWER 0x08 0x08 Y IR only BACK 0x28 0x8028 Y HOME 0x7C 0x807C Y

←

0x07 0x8007 Y

→

0x06 0x8006 Y

↑

0x40 0x8040 Y ↓ 0x41 0x8041 Y OK 0x75 0x8044 Y CH + 0x00 0x8000 Y CH - 0x01 0x8001 Y VOL + 0x02 0x8002 Y VOL - 0x03 0x8003 Y MUTE 0x09 0x8009 Y . 3D_Mode 0xDC 0x80DC Y MyAPPS 0x42 0x8042 Y VOICE 0x800A Y = VOICE_START

Logical

Buttons

AUTO_WAKEUP X 0x800C VOICE_START X 0x800A VOICE_STOP X 0x800D POINT_START X 0x803E POINT_STOP X 0x803F

power

mute

home

↑

ok

← →

↓

voice

vol ch

M3 Remote M4 Remote

power

back home

↑

ok

← →

↓

mute

vol ch

3D star

LGE Internal Use Only

MPU-3050 (Gyro) (Invensense)

LIS331DLH(Accel.) (STMicro)

BCM20733M

(BROADCOM) Bluetooth 3.0

Key Button ( 4 x 5 )

AA x 2 Battery

DC-DC 2.8V LDO

Power Management

Bluetooth Remocon

Bluetooth Receiver

BCM20702M

(BROADCOM) Bluetooth 4.0

Antenna

Connector

X-tal 20 MHz

Antenna

X-tal 24 MHz

3. M4 Block Diagram

2.8V LDO

256Kbit (E2PROM)

512Kbit (Serial Flash)

I2C

SPI

UART

SPI

WM8950 (Wolfson)

Voice

MIC. (Knowles)

I2S

M4 4-mode Only

LGE Internal Use Only

주요 Item IC Manufacturer Function

Remocon

Voice

Voice Codec WM8950 Wolfson 16KHz Sampling of Audio data

MEMS Mic. SPU0414HR5H Knowles Sensing Voice

Motion Sensor

Gyro Sensor ITG3050 Invensense Sensing angular velocity of X, Y, Z-axis

Accelerometer MMA8452 Stmicro Sensing device tilt (Pitch & Roll angle)

RF

+

Micom

RF Antenna SDBTPTR3015 Partron

Wireless communication

X-tal 24MHz Partron

RF + Micom BCM20733 Broadcom

DC-DC Converter TPS61097 TI Battery Boost up Regulator

LDO1 uPI7716 uPI RF, Gyro, Accelerometer Power Supply

LDO2 uPI7716 uPI Audio Codec, Mic. Power Supply

4. Function list

LGE Internal Use Only

5. RF Pairing / Un-pairing Method

Method Description

RF Pairing

 Method1

– If unpaired, just press "OK" button. – If paired, press "OK" button after

unpairing.

 Method 2 (Repairing)

– Press “BACK" button for 5 sec.

• When do pairing, the remote

should make pairing request IR signal(0x29) to TV.

• When TV receive the IR signal, it

should send "pairing request packet" to the RF receiver.

• After pairing success, the remote

should blink LED for some time and TV send "pairing success packet" back to TV.

• When remote try to unpairing, it

doesn’t care about state of receiver(stand alone).

RF Unpairing

Press “HOME" button and “BACK" button at the same time for 5 sec.

• When remote try to unpairing, it

doesn’t care about state of receiver(stand alone).

• After unpairing, all pairing

information should be erased.

• After unpairing, LED should be

blinked for 3sec.

• The remote just becomes to IR

mode.

LGE Internal Use Only

Introductions of 12Y WIFI built in ass’y

LGE Internal Use Only

WIFI Built in ass’y feature(LGIT)

WIFI built in feature

PIN USB interface

1 5V

2 DM

3 DP

4 GND

-Pin map

- Block diagram

LGE Internal Use Only

WIFI Built in Block-diagram(Arcadyan)

LGE Internal Use Only

WIFI Built in ass’y Specification

LGE Internal Use Only

12Y Widevine & HDCP 2.0 & NETFLX

1. Widevine?

2. HDCP 2.0 & NETFLIX?

3. DTCP?

4. Changed BOM

LGE Internal Use Only

1. Widevine?

[Widevine]

Widevine is the Solution(Library) offering Adaptive Streaming and DRM. In BBTV, when special CP do service, this module is required key. Currently CP which is requested to widevine, is typically Australian Bigpond Live and North American CinemaNow. Furthermore, because the future will be the spread of CP, widevine key download for the global model should be applied to production. (Because operation unique key should be downloaded for Widevine , Widevine key dowmload by NSU is impossible.)

[Widevine]

Widevine is the Solution(Library) offering Adaptive Streaming and DRM. In BBTV, when special CP do service, this module is required key. Currently CP which is requested to widevine, is typically Australian Bigpond Live and North American CinemaNow. Furthermore, because the future will be the spread of CP, widevine key download for the global model should be applied to production. (Because operation unique key should be downloaded for Widevine , Widevine key dowmload by NSU is impossible.)

[Widevine Key] Widevine Key is unique data stored TV for using Widevine.

LGE Internal Use Only

 HDCP

9

High-bandwidth Digital Content Protection

9 Protect high-value digital motion pictures, television programs and audio

against unauthorized interception and copying between a digital set top box or digital video recorder and a digital TV or PC.

9 Specification developed by Intel Corporation to protect digital entertainment

across the DVI/HDMI interface.

 Why HDCP2.0?

9 HDCP revision 2.0 supports a broader range of wired and wireless interfaces.

 Netflix 9 the services maintain a huge selection of movies and latest releases and offer

DVD rentals via mail & online streaming.

2. HDCP 2.0 & NETFLIX?

LGE Internal Use Only

3. DTCP?

[DTCP]

The Digital Transmission Content Protection Specification defines a cryptogrphic protocol for protecting audio/video entertainment content from unauthorized copying, intercepting, and tampering as it traverses digital transmission mechanisms such as a high-performance serial bus that conforms to the IEEE 1394-1995 standard. Only legitimate entertainment content delivered to a source device via another approved copy protection system (such as the DVD Content Scrambling System) will be protected by this protection system.

[Three cryptographic Keys]

• Authentication Key which is formed as a result of authentication and used to protect the exchange keys.

•Exchage Key which is used to set up and protect content streams.

•Content Key which is used to encrpt the content being exchanged.

[DTCP]

The Digital Transmission Content Protection Specification defines a cryptogrphic protocol for protecting audio/video entertainment content from unauthorized copying, intercepting, and tampering as it traverses digital transmission mechanisms such as a high-performance serial bus that conforms to the IEEE 1394-1995 standard. Only legitimate entertainment content delivered to a source device via another approved copy protection system (such as the DVD Content Scrambling System) will be protected by this protection system.

[Three cryptographic Keys]

• Authentication Key which is formed as a result of authentication and used to protect the

exchange keys.

•Exchage Key which is used to set up and protect content streams.

•Content Key which is used to encrpt the content being exchanged.

LGE Internal Use Only

4. Changed BOM

As-Was Current

Æ 추가

 Add Item

1.Marlin (Yes/No)

2.CNTV (Yes/No)

3.HDCP Tx (Yes/No)

4.DTCP Rx (Yes/No)

5.HDCP Rx (Yes/No)

주3) CNTV [Yes] : China Smart TV Only

LGE Internal Use Only

4. Changed BOM

LGE Internal Use Only

Contents of LCD TV Standard Repair Process

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

1

A. Video error

No video/Normal audio 1

2 No video/No audio 2

3 Video error, video lag/stop, fail tunning 3, 4

4 Color error 5

5

Vertical/Horizontal bar, residual image, light spot, external device color error

6

B. Power error

No power 7

7

Off when on, off while viewing, power auto on/off

8

C. Audio error

No audio/Normal video 9

9 Wrecked audio/discontinuation/noise 10

10

D. Function error

No response in remote controller, key error, recording error, memory error

11

11 External device recognition error 12

12 E. Noise Circuit noise, mechanical noise 13

13 F. Exterior error Exterior defect 14

First of all, Check whether there is SVC Bulletin in GCSC System for these model.

LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual

No. Error symptom Content Page Remarks

1

A. Video error_ No video/Normal audio

Check LCD back light with naked eye A1 2 LED driver B+ 24V measuring method A2 3 Check White Balance value A3 4 Power Board voltage measuring method A4 6

A. Video error_ No video/Video lag/stop

TUNER input signal strength checking method A6 7 LCD-TV Version checking method A7 9

A. Video error_Color error

LCD TV connection diagram A8

10 Tuner Checking Part A9

11 Check Link Cable (LVDS) reconnection condition

A10 A11

A10 : 32/37/42/47/55

A11 : 32 AUO 12 Adjustment Test pattern - ADJ Key A12 13

A. Video error_Vertical/Horizontal bar, residual image, light spot

LCD TV connection diagram A8

14 Check Link Cable (LVDS) reconnection condition

A10 A11

A10 : 32/37/42/47/55

A11 : 32 AUO 15 Adjustment Test pattern - ADJ Key A12 16

Defected Type caused by T-Con/ Inverter/ Module

Exchange T-Con Board (1) A-1/5

17 Exchange T-Con Board (2) A-2/5

18 Exchange LED driver Board (PSU) A-3/5

55” : driver board

Other : PS 19 Exchange Module itself (1) A-4/5 20 Exchange Module itself (2) A-5/5

Continue to the next page

LGE Internal Use Only

Normal

audio

Y

N

Move to No video/No audio

No video Normal audio

Check Back Light On with naked eye

On

Y

N

Check Power Board 12v,3.5v etc.

Normal

voltage

Y

N

Replace T-con Board or module And Adjust VCOM

Repair Power Board or parts

Check Power Board 24v output

Normal voltage

Y

Replace Inverter or module

N

Repair Power Board or parts

End

Always check & record S/W Version and White Balance value before replacing the Main Board

Replace Main Board

Re-enter White Balance value

※Precaution

Established

date

Standard Repair Process

Revised date

1/13

LCD TV

Error

symptom

A. Video error

No video/ Normal audio

☞A4☞A1

☞A2

☞A28

☞A7 & A3

First of all, Check whether all of cables between board is inserted properly or not.

(Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)

2010. 12 .14

LGE Internal Use Only

Normal

voltage?

Check various voltages of Power Board ( 3.5V,12V,20V or 24V…)

No Video/ No audio

Check and replace MAIN B/D

Y

Replace Power Board and repair parts

N

End

Standard Repair Process

A. Video error

No video/ No audio

☞A4

Established

date

Revised date

2/13

LCD TV

Error

symptom

2010. 12 .14

LGE Internal Use Only

A. Picture Problem

Picture broken/ Freezing

Y

N

☞ A6

N

Check RF Signal level

Normal Signal?

Check RF Cable

Connection

1. Reconnection

2. Install Booster

Check

S/W Version

Booster menu On→Off: Check Off→On: Check

S/W Upgrade

Check whether other equipments have problem or not.

(By connecting RF Cable at other equipment)

→ DVD Pla yer ,Set-Top-Box, Different maker TV etc`

SVC

Bulletin?

Replace

Main B/D

Check

Tuner soldering

Normal

Picture?

Y

N

Y

Close

Normal

Picture?

Y

Close

■

Menu→Setup →Booster

. By using Digital signal level meter . By using Diagnostics menu on OSD

( Menu→ Set up→ Support → Signal Test )

- Signal strength (Normal : over 50%)

- Signal Quality (Normal: over 50%)

Normal

Picture?

Y

Contact with signal distributor

or broadcaster (Cable or Air)

N

Normal

Picture?

Y

Close

N

☞ A7

Standard Repair Process

Established

date

Revised date

3/13

LCD TV

Error

symptom

2010. 12 .14

LGE Internal Use Only

A. Picture Problem (DVB-S/S2)

Tuning fail, Picture broken/ Freezing

Y

N

☞ A6

Check RF Signal level

Normal Signal?

Check

S/W Version

S/W Upgrade

SVC

Bulletin?

Normal

Picture?

Y

N

Y

Close

Check RF signal cable (DVB satellite signal or not)

Check whether other equipments have problem or not. (By connecting RF Cable at other equipment)

→ Set-Top-Box, Different maker TV etc

Y

Change satellite setting

(match with installed ANT)

N

Normal

Picture?

Y

Close

N

☞ A7

Standard Repair Process

Established

date

Revised date

3/13

LCD TV

Error

symptom

2011. 01 .24

Check satellite setting.

- Check LNB frequency.

- Check satellite

- Check Satellite connection

(DiSEqC, motor, etc…)

Normal

setting?

Contact with

signal distributor

or broadcaster

(Cable or Air)

Close

N

Check

Tuner soldering

Replace

Main B/D

LGE Internal Use Only

Color

error?

Y

N

※ Check and replace Link Cable (LVDS) and contact condition

Y

N

Replace Main B/D

Color

error?

Check error color input mode

Check color by input

-External Input

-COMPONENT

-RGB

-HDMI/DVI

Y

External device

/Cable

normal

External Input/

Component

error

Check external device and cable

Y

External device

/Cable

normal

RGB/

HDMI/DVI

error

Check external device and cable

Replace Main B/D

N

A. Video error

Color error

☞A8

N

Y

End

Replace module

Request repair

for external

device/cable

Color

error?

Check Test pattern

☞A12

☞ A10/ A11

Standard Repair Process

Established

date

Revised date

4/13

LCD TV

Error

symptom

2010. 12 .14

LGE Internal Use Only

Screen

normal?

N

Y

Check external device connection condition

Y

N

Check and replace Link Cable

Normal?

Y

N

Screen

normal?

Replace Main B/D (adjust VCOM)

Replace module

Check color condition by input

-External Input

-Component

-RGB

-HDMI/DVI

End

Vertical/Horizontal bar, residual image, light spot

Request repair for external device

A. Video error

Vertical / Horizontal bar, residual image, light spot, external device color error

☞A12

External device screen error-Color error

External

Input error

Connect other external device and cable

(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

N

Y

Replace Main B/D

Screen

normal?

Check screen condition by input

-External Input

-Component

-RGB

-HDMI/DVI

Request repair for external device

Component

error

RGB

error

HDMI/

DVI

Connect other external device and cable

(Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

Replace Main B/D

Screen

normal?

N

Y

Check S/W Version

Y

N

Check

version

S/W Upgrade

Y

N

Normal

screen?

End

Y

N

Replace Main B/D

For LGD panel

Replace Module

Screen

normal?

End

Established

date

Revised date

5/13

LCD TV

Error

symptom

Standard Repair Process

☞A8

☞ A10/ A11

Check Test pattern

☞ A28

For other panel

2010. 12 .14

LGE Internal Use Only

B. Power error

No power

Power LED

On?

Y

N

DC Power on by pressing Power Key On Remote control

Y

N

Normal

operation?

Check Power On ‘”High”

Check Power cord was inserted properly

Check Power LED

Replace Power B/D

Measure voltage of each output of Power B/D

N

Y

Normal

voltage?

Replace Main B/D

N

Y

OK?

Replace Main B/D

N

Y

Normal?

Check ST-BY 3.5V

Replace Power B/D

N

Y

Normal

voltage?

Replace Power B/D

Y

☞A17

☞A18

☞A19

☞A4

Standard Repair Process

Established

date

Revised date

6/13

LCD TV

Error

symptom

. Stand-By: Red . Operating: white

※

Close

2010. 12 .14

LGE Internal Use Only

B. Power error

Off when on, off while viewing, power auto on/off

Error?

N

Y

Check Power Off Mode

Fix A/C cord & Outlet and check each 3 phase out

Check A/C cord

Check for all 3- phase

power out

Check outlet

Replace Main B/D

CPU

Abnormal

(If Power Off mode is not displayed) Check Power B/D voltage

Y

N

Replace Main B/D

Normal

voltage?

Replace Power B/D

N

Y

Normal?

End

※ Caution

Check and fix exterior of Power B/D Part

☞A22

☞A19

Established

date

Revised date

7/13

LCD TV

Error

symptom

Standard Repair Process

Status Power off List Explanation

Normal

"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL "POWEROFF_OFFTIMER"

Power off by OFF TIMER "POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER "POWEROFF_INSTOP" Power off by INSTOP KEY "POWEROFF_AUTOOFF" Power off by AUTO OFF "POWEROFF_ONTIMER" Power off by ON TIMER "POWEROFF_RS232C" Power off by RS232C "POWEROFF_RESREC" Power off by Reservated Record "POWEROFF_RECEND" Power off by End of Recording "POWEROFF_SWDOWN" Power off by S/W Download "POWEROFF_UNKNOWN" Power off by unknown status except listed case

Abnormal

"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble "POWEROFF_CPUABNORMAL" Power off by CPU Abnormal

* Please refer to the all cases which

can be displayed on power off mode.

Abnormal

1

2010. 12 .14

LGE Internal Use Only

No audio Screen normal

Check user menu > Speaker off

Off

N

Y

Cancel OFF

Check audio B+ 24V of Power Board

Normal voltage

Y

N

Replace Power Board and repair parts

Check Speaker disconnection

N

Y

Replace Speaker

Replace MAIN Board End

C. Audio error

No audio/ Normal video

☞A24 ☞A25

Disconnection

Established

date

Revised date

8/13

LCD TV

Error

symptom

Standard Repair Process

2010. 12 .14

LGE Internal Use Only

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

C. Audio error

Wrecked audio/ discontinuation/noise

Wrecked audio/

Discontinuation/

Noise for

all audio

Check and replace speaker and connector

Wrecked audio/ Discontinuation/

Noise only

for D-TV

Wrecked audio/ Discontinuation/

Noise only

for Analog

Wrecked audio/ Discontinuation/

Noise only

for External Input

Connect and check other external device

N

Y

Normal

audio?

Check and fix external device

Replace Power B/D

N

Y

Normal

voltage?

Check input signal

-RF

-External Input signal

Signal

normal?

(When RF signal is not received) Request repair to external cable/ANT provider

Y

Check audio B+ Voltage (24V)

Replace Main B/D

(In case of External Input signal error) Check and fix external device

Replace Main B/D

N

End

Established

date

Revised date

9/13

LCD TV

Error

symptom

Standard Repair Process

☞A25

2010. 12 .14

LGE Internal Use Only

D. General Function Problem

Remote control & Local switch checking

Y

N

1. Remote control(R/C) operating error

Check R/C itself

Operation

Normal

operating?

Normal

operating?

Y

Close

Replace R/C

If R/C operate,

Explain the customer

cause is interference

from light in room.

Check R/C Operating

When turn off light

in room

Check & Replace

Baterry of R/C

Check & Repair Cable connection Connector solder

Normal

operating?

Check B+ 3.5V

On Main B/D

☞A27

Normal

Voltage?

Close

N

Check 3.5v on Power B/D

Replace Power B/D or

Replace Main B/D

(Power B/D don’t have problem)

☞A4

Check IR

Output signal

Normal

Signal?

N

Y

Repair/Replace

IR B/D

N

☞A27

Replace

Main B/D

Y

☞A27

Standard Repair Process

Established

date

Revised date

10/13

LCD TV

Error

symptom

2010. 12 .14

LGE Internal Use Only

Check technical information

- Fix information

- S/W Version

N

Y

Technical

information?

Check input signal

Signal input?

Y

N

External Input and

Component

Recognition error

Check and fix external device/cable

RGB,HDMI/ DVI, Optical

Recognition error

Replace Main B/D

Fix in

accordance

with technical

information

D. Function error

External device recognition error

Established

date

Revised date

11/13

LCD TV

Error

symptom

Standard Repair Process

2010. 12 .14

LGE Internal Use Only

Check location of noise

Identify nose type

Circuit

noise

Replace PSU(with LED driver)

Replace LED driver

Mechanical

noise

Check location of noise

OR

※ When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description)

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

OR

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

E. Noise

Circuit noise, mechanical noise

Established

date

Revised date

12/13

LCD TV

Error

symptom

Standard Repair Process

2010. 12 .14

LGE Internal Use Only

Replace module

Zoom part with exterior damage

Module

damage

Cabinet damage

Replace cabinet

Replace remote controller

Remote

controller

damage

Stand

dent

Replace stand

F. Exterior defect

Exterior defect

Adjust VCOM

Established

date

Revised date

13/13

LCD TV

Error

symptom

Standard Repair Process

☞A28

2010. 12 .14

LGE Internal Use Only

Contents of LCD TV Standard Repair Process Detail Technical Manual

No. Error symptom Content Page Remarks

21

B. Power error_No power

Check front display LED A17

22 Check power input Voltage & ST-BY 5V A18

23 Checking method when power is ON A19

24 POWER BOARD voltage measuring method A4

25

26

B. Power error_Off when on, off while viewing

POWER OFF MODE checking method A22

27

B. Power error_Off when on, off while viewing

POWER BOARD PIN voltage checking method A19

28

C. Audio error_No audio/Normal video

Checking method in menu when there is no audio

A24

29

Voltage and speaker checking method when there is no audio

A25

30

C. Audio error_Wrecked audio/discontinuation

Voltage and speaker checking method in case of audio error

A25

31

D. Function error_ No response in remote controller, key error

Remote controller operation checking method A27

32 D. VCOM Adjustment Sequence of the Vcom adjustment A28

Continued from previous page

LGE Internal Use Only

Entry method

1. Press the ADJ button on the remote controller for adjustment.

2. Enter into White Balance of item 6.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re- enter the value after replacing the MAIN BOARD.

Standard Repair Process Detail Technical Manual

Check White Balance value

A. Video error_No video/Normal audio

A4

Established

date

Revised

date

Error

symptom

Content

LCD TV

Entry method

1. Press the ADJ button on the remote controller for adjustment.

2. Enter into White Balance of item 7.

3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), reenter the value after replacing the MAIN BOARD.

2010. 12 .14

LGE Internal Use Only

LG 42LM660T, 42LM660T-ZA, 42LM669S, 42LM669T, 42LM669T-ZC Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual