LG 47LD650H User Manual

OWNER’S MANUAL

LCD TV

Please read this manual carefully before operating
your set and retain it for future reference.

32LG710H
37LG710H
42LG710H

P/NO : SAC34134301 (1101-REV04)

32LD650H
37LD650H
42LD650H
47LD650H
55LD650H

32LD655H
37LD655H
42LD655H

www.lg.com

2

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi­tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation (of the device).

Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating
and maintenance (servicing) instructions in the
literature accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

3

SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radia­tors, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong, The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your out­let, consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta­cles, and the point where they exit from the appara­tus.

Only use attachments/accessories specified by the
manufacturer.

Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the appa­ratus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.

Unplug this apparatus during lighting storms or
when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

Never touch this apparatus or antenna during a
thunder or lighting storm.

When mounting a TV on the wall, make sure not to
install the TV by the hanging power and signal cables
on the back of the TV.

Do not allow an impact shock or any objects to fall
into the product, and do not drop onto the screen
with something.

IMPORTANT SAFETY INSTRUCTIONS

1

2

3

4

5

7

8

9

10

11

12

13

6

4

CAUTION concerning the Power Cord :
It is recommend that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet as this could result in fire or elec­tric shock.
Do not overload wall outlets. Overloaded wall out­lets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the
TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.

As long as this unit is connected to the AC wall out­let, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.

Do not expose to dripping or splashing and do not
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).

GGRROOUUNNDDIINNGG
Ensure that you connect the earth ground wire to

prevent possible electric shock. (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding
methods are not possible, have a qualified electri­cian install a separate circuit breaker.

Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The plug

must remain readily operable.

DDoott DDeeffeecctt
The Plasma or LCD panel is a high technology

product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.

GGeenneerraatteedd SSoouunndd
“Cracking” noise: A cracking noise that occurs

when watching or turning off the TV is generated
by plastic thermal contraction due to tempera­ture and humidity. This noise is common for prod­ucts where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low
level noise is generated from a high-speed switch­ing circuit, which supplies a large amount of cur­rent to operate a product. It varies depending
on the product.

This generated sound does not affect the per­formance and reliability of the product.

Owner Manual

14

17

18

19

Power
Supply

Short-circuit

Breaker

20

15

16

21

5

AANNTTEENNNNAASS
OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg

If an outdoor antenna is installed, follow the precau­tions below. An outdoor antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
come in contact with such power lines or circuits as
death or serious injury can occur.

Be sure the antenna system is grounded so as to pro­vide some protection against voltage surges and
built-up static charges.

Section 810 of the National Electrical Code (NEC) in
the U.S.A. provides information with respect to prop­er grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes and requirements for the grounding elec­trode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700

CClleeaanniinngg
When cleaning, unplug the power cord and scrub

gently with a soft cloth to prevent scratching. Do not
spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemi­cals such as alcohol, thinners or benzene.

MMoovviinngg

Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.

VVeennttiillaattiioonn

Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other mate­rials (e.g.) plastic while plugged in. Do not install in
excessively dusty places.

Take care not to touch the ventilation openings.
When watching the TV for a long period, the venti­lation openings may become hot.

If you smell smoke or other odors coming from the
TV, unplug the power cord contact and authorized
service center.

Do not press strongly upon the panel with a hand or
sharp object such as nail, pencil or pen, or make a
scratch on it.

Keep the product away from direct sunlight.

FF oo rr LLCCDD TTVV

If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.

Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary dis­tortion effects on the screen.

24

22

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

25

26

27

28

23

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.

29

30

6

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 3

FEATURES OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stand Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cable Management

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Attaching the TV to a desk

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Securing the TV to the wall to prevent falling
When the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . 23

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 24

MPI Card Slot / PPV Card Installation

. . . . . . . . . . . . . . 25

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Audio Out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

WATCHING TV / CHANNEL CONTROL

Remote Control Functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Turning On The TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 42

- Add / Delete Channel (Manual Tuning)

. . . . . . 43

- Channel Editing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Channel Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Example Electronic Program Guide

. . . . . . . . . . . . . . . . . . . 46

USB

Entry Modes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Extra Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

PICTURE CONTROL

PIP (Picture-In-Picture)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Picture Size (Aspect Ratio) Control

. . . . . . . . . . . . . . . . . . 58

Preset Picture Settings (Picture Mode)

. . . . . . . . . . . . .

61

Manual Picture Adjustment - User Mode

. . . . . . . . . .

62

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 63

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Demo mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 67

Preset Sound Settings (Sound Mode)

. . . . . . . . . . . . . . 68

Sound Setting Adjustment - User Mode

. . . . . . . . . . .69

- SRS TruSurround XT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

- Infinite Sound

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Clear Voice ll

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

74

Stereo/SAP Broadcast Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

On-Screen Menus Language Selection

. . . . . . . . . . . . . . 77

Caption Mode

- Analog Broadcasting System Captions

. . . . . . . 78

- Digital Broadcasting System Captions

. . . . . . . . 79

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

7

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Auto Shut-Off Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

PARENTAL CONTROL / RATINGS

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Downloadable Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99

Programming the Remote Control

. . . . . . . . . . . . . . . . . . . 101

IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4

Open Source License

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6

8

FEATURES OF THIS TV

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN

Automatically enhances and amplifies the sound of
human voice frequency range to help keep dialogue
audible when background noise swells.

LG TV include a unique invisible speaker system,
tuned by renowned audio expert, Mr. Mark Levinson.
Speakers are embedded in strategic spots behind the
front cabinet and use minute vibrations to turn the
entire front bezel into the speaker system. The result
is a clean, polished look, and enhanced audio by
increasing the “sweet spot”, giving a wider and richer
sound field.

HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.

Unlike other sensors which can only sense brightness
of ambient light, LG’s “Intelligent Sensor” uses 4,096
sensing steps to evaluate its surroundings. Using a
sophisticated algorithm, the LG processes picture
quality elements including brightness, contrast, color,
sharpness and white balance. The result is a picture
optimized for it’s surroundings, more pleasing to
watch and which can also save up to 50% in power
consumption.

Matches the original frame rate of the film for a more
film-like experience

View videos and photos and listen to music on your
TV through USB 2.0 (‘videos’ dependent on model).

■

This feature is not available for all models.

PREPARATION

9

PREPERATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner’s Manual

Power Cord

CD Manual

Protective Bracket and

Screw for Power Cord

(Refer to P.17, P.18)

Cable Holder

(Refer to P.17)

* Wipe spots on the exterior only with the pol-

ishing cloth.

* Do not wipe roughly when removing stains.

Excessive pressure may cause scratches or
discoloration.

Polishing Cloth

(Not included with all

models.)

OOppttiioonnaall EExxttrraass

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.

x 2

Torx plus

Star head screw

(Refer to P.15, P.16)

Screw for

stand fixing

(Refer to P.20)

Screws for stand

assembly

(Refer to P.15)

x 4 x 4

1.5V 1.5V

Remote Control,

Batteries

MUTE

RETURN

CC

TV

POWER

GUIDE

PORTAL

ENTER

VOL

CH

123

456

78

0

9

FLASHBK

VCR

DVD

INPUT

MENU

INFO

i

STB

P

A
G
E

PIP

SAP

PIP CH-

PIP CH+

PIP SWAP

PIP INPUT

ALPHA/NUM

REMOVE

RATIO

TIMER

ABC

DEF

GHI

WXYZ

TUV

PQRS

MNO

JKL

&@

.:/,

Protection Cover

(Refer to P.15)

Plug-in type Holder

(Refer to P.17)

FFoorr 3322//3377//4422LLGG771100HH

(For 32LG710H)

Screws for stand

fixing

(Refer to P.20)

Washers for stand

fixing

(Refer to P.20)

x 2

Cable Holder

(Refer to P.18)

Plug-in type Holder

(Refer to P.18)

(For 32/37/42LD650H, 32/37/42LD655H)

Screw for stand fixing

(Refer to P.20)

Screws for stand assembly

(Refer to P.16)

x 8

(M4 x 20)

Protection Cover

(Refer to P.16)

FFoorr 3322//3377//4422//4477//5555LLDD665500HH,, 3322//3377//4422LLDD665555HH

Nuts for stand

fixing

(Refer to P.20)

x 2

x 2

Rubbers for stand

fixing

(Refer to P.20)

x 4

x 2

PREPARATION

10

PREPARATIONPREPARATION

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

POWER Button

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is

switched on.

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

Remote Control Sensor

CHANNEL( , )
Buttons

Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

32/37/42LG710H

CH

VOL

ENTER

MENU

INPUT

PREPARATION

11

Intelligent Sensor

Adjusts picture according to the surrounding condi­tions.

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is

switched on.

Remote Control Sensor

SPEAKER

VOLUME (+, -)
Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

CHANNEL( , )
Buttons

32/37/42/47/55LD650H, 32/37/42LD655H

CH

VOL

ENTER

MENU

INPUT

PREPARATION

12

PREPARATION

■

Image shown may differ from your TV.

BACK PANEL INFORMATION

R

/

10

3

8

R

ANTENNA INANTENNA IN

M.P.I.M.P.I.

7

1

4

92

13

14

15

6

6

5

32/37/42LG710H

12

11

11

16

HDMI/DVI IN

2

1(DVI)

INTERFACE

RJP

USB IN

GAME

CONTROL

UPDATE

RS-232C IN

(SERVICE ONLY)

AV IN 1

OPTICAL

DIGITAL

AUDIO OUT

AUDIO

/

MONO

SPEAKER OUT

8

REMOTE

CONTROL OUT

VIDEO

R

AUDIO

L/MONO

VIDEO

AV IN 2

LAN

(SERVICE ONLY)

RGB(PC)

RGB IN

VIDEO

COMPONENT IN

RESET

TV-LINK

CFG

(RGB/DVI)

AUDIO

AUDIO

PREPARATION

13

R

ANTENNA INANTENNA IN

M.P.I.M.P.I.

14

6

32/37/42LD650H, 32/37/42LD655H

REMOTE

CONTROL

OUT

OPTICAL

DIGITAL

UPDATE

RESET

LAN

HDMI/DVI IN

2

1

RJP

INTERFACE

SPEAKER

OU

T

8

RGB IN (PC)

AUDIO IN

(RGB/DVI)

TV-LINK CFG

GAME

CONTROL

RS-232C IN

(SERVICE ONLY)

AUDIO OUT

A
V IN 1

AUDIO

VIDEO

MONO

/

COMPONENT

IN

L

R

AC IN

1

13

3

4

2

10

9

6

5

8

/

15

7

47/55LD650H

REMOTE

CONTROL

OUT

OPTICAL

DIGITAL

UPDATE

RESET

LAN

HDMI/DVI IN

2

1

RJP

INTERFACE

SPEAKER

OU

T

8

RGB IN (PC)

AUDIO IN

(RGB/DVI)

TV-LINK CFG

GAME CONTROL

/ M.P

.I.

RS-232C IN

(SERVICE ONLY)

AUDIO OUT

A
V IN 1

AUDIO

VIDEO

MONO

/

COMPONENT

IN

L

R

ANTENNA IN

1

13

3

4

2

10

6

5

8

7

9

14

11

11

AC IN

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

/

15

12

12

11

16

16

11

USB IN

R

AUDIO

L/ MONO

VIDEO

AV IN 2

PREPARATION

14

PREPARATION

HDMI/DVI IN

Digital Connection. Supports HD video and Digital
audio.

Accepts DVI video using an adapter or HDMI to DVI
cable (not included)

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).

AUDIO IN (RGB/DVI)

1/8” headphone jack for analog PC audio input.

LAN (SERVICE ONLY)
For connecting to a control network.

RESET

Performs a hardware reset.

UPDATE

Enables/disables software downloads and debug mode.

TV - LINK CFG

Computer input for programming Free To Guest ser­vices.

GAME CONTROL

Input port for third party game Controllers.

M.P. I.

Allows VOD/PPV devices or set-top boxes to control
the TV.

RS-232C IN (SERVICE ONLY)

Used for software updates.

OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and
home theater systems.

Note: In standby mode, this port doesn’t work.

SPEAKER OUT 8

Ω

For use with external speakers.

REMOTE CONTROL OUT

IR output for controlling an auxiliary device.

AV (Audio/Video) IN 1/2

Analog composite connection. Supports standard
definition video only (480i).

COMPONENT IN

Analog Connection. Supports HD.
Uses a red, green, and blue cable for video & a red

and white cable for audio.

RJP INTERFACE (REMOTE JACK PACK PORT)

Connect this to an LG remote jack pack system.

ANTENNA IN

Connect an antenna to receive over-the-air (OTA)
signals.

Power Cord Socket

AC power input.
Caution: Never attempt to operate the TV on DC

power.

USB IN

Used for viewing multimedia files.

1

2

3

4

5

6

8

7

9

11

12

13

14

15

10

16

PREPARATION

15

STAND INSTRUCTIONS

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the parts of the

SSTT AANNDD BB OODDYY

with the

SSTT AANNDD BBAA SSEE

of the TV.

1

2

Insert the stand as shown.

3

SSTT AANNDD BBOO DDYY

SSTT AANNDD BBAA SSEE

■

Image shown may differ from your TV.

GG

When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened
fully, the TV can tilt forward after the protuct
installation). Do not over tighten.

NOTE

!

DETACHMENT

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Remove the four screws that hold the base on.

2

Detach the stand from the TV.

3

INSTALLATION

4

or

x 4

Tighten the stand with the
four screws (provided as parts
of the TV).

Tighten the two of these four screws
and the two Torx plus star head screws

(provided as parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a star head dri­ver bit (not provided as parts of the TV).

x 2

x 2

After removing the stand, install the included
pprrootteecctt iioonn ccoovv eerr

over the hole for the stand.

Press the

PPRR OOTTEECCTTIIOO NN CCOOVVEERR

into the TV

until you hear it click.

PROTECTION COVER

32/37/42LG710H

PREPARATION

16

PREPARATION

32/37/42/47/55LD650H, 32/37/42LD655H

AC IN

C
A
B
L
E
M

A
N
A
G
E
M

E
N
T

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the parts of the

SSTT AANNDD BB OODDYY

with the

SSTT AANNDD BBAA SSEE

of the TV.

1

2

Assemble the TV as shown.

3

A
C

I
N

C
A
B
L

E
M
A
N

A
G
E
M

E
N

T

SSTT AANNDD BBOO DDYY

SSTT AANNDD BBAA SSEE

GG

When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened
fully, the TV can tilt forward after the protuct
installation). Do not over tighten.

NOTE

!

DETACHMENT

A

C
I
N

C
A
B
L

E
M
A
N

A
G
E
M
E
N

T

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Remove the screws that hold the stand on.

2

Detach the stand from TV.

3

A

C
I
N

C
A
B

L
E
M
A

N
A
G

E
M
E
N

T

INSTALLATION

After removing the stand, install the included
pprrootteecctt iioonn ccoovv eerr

over the hole for the stand.

Press the

PPRR OOTTEECCTTIIOO NN CCOOVVEERR

into the TV

until you hear it click.

PROTECTION COVER

A

C
I

N

C

A
B
L
E

M
A
N
A
G

E
M
E
N

T

M4 x 20

4

or

x 4

Tighten the stand with the
four screws (provided as parts
of the TV).

Tighten the two of these four screws
and the two Torx plus star head screws

(provided as parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a star head dri­ver bit (not provided as parts of the TV).

x 2

x 2

PREPARATION

17

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.
To help prevent the power cable from being
removed by accident, secure the power
cable with the included PPROTECTIVE

BRACKET /SCREW. The 32LG710H use a
Plug-in type Holder instead of using a

screw.

Open the CABLE MANAGEMENT CLIP as
shown.

If a CABLE HOLDER was included with your

TV, install it as shown.

1

2

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

GG

Do not hold the CABLE MANAGEMENT CLIP
when moving the TV.

- If the TV is dropped, you may be injured or the
product may be broken.

GG

With some TVs, the PLUG-IN TYPE HOLDER
and the CABLE HOLDER are included. If these
holders are inserted into the hole provided on
back of the TV, they cannot be removed.

NOTE

!

CABLE MANAGEMENT CLIP

CABLE HOLDER

PROTECTIVE BRACKET/SCREW

PLUG-IN TYPE HOLDER
(For 32LG710H model)

Or

32/37/42LG710H

PREPARATION

18

PREPARATION

32/37/42/47/55LD650H, 32/37/42LD655H

Connect the cables as necessary.
To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.
To help prevent the power cable from being
removed by accident, secure the power cable
with the included PPROTECTIVE BRACKET
/SCREW. The 32/37/42LD650H,
32/37/42LD655H use a Plug-in type
Holder instead of using a screw.

1

AC IN

Open the CABLE MANAGEMENT CLIP as
shown.

If a CABLE HOLDER was included with your
TV, install it as shown.

2

AC IN

AC IN

PROTECTIVE BRACKET/SCREW

PLUG-IN TYPE HOLDER
(For 32/37/42LD650H,

32/37/42LD655H model)

Or

GG

Do not hold the CABLE MANAGEMENT CLIP
when moving the TV.

- If the TV is dropped, you may be injured or the
product may be broken.

GG

With some TVs, the PLUG-IN TYPE HOLDER
and the CABLE HOLDER are included. If these
holders are inserted into the hole provided on
back of the TV, they cannot be removed.

NOTE

!

CABLE MANAGEMENT CLIP

CABLE HOLDER

(For 32/37/42LD650H,

32/37/42LD655H model)

Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.

3

PREPARATION

19

PREPARATION

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

■

Image shown may differ from your TV.

4 inches

4 inches

4 inches

4 inches

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction to suit your viewing posi­tion.

GG

Ensure adequate ventilation by following the clearance recommendations.

GG

Do not mount near or above any type of heat source.

CAUTION

20°: 47/55LD650H
90°: Other Models

PREPARATION

20

PREPARATION

ATTACHING THE TV TO A DESK

The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.

G

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

4-Screws

(not provided as parts of the product)

G

Recommended screw size: M5 x L (

*L: Table depth + 8~10mm

)

ex) Table depth: 15mm, Screw: M5 x 25

Desk

Stand

32/37/42LD650H, 32/37/42LD655H

Stand

Desk

32/37/42LG710H

47/55LD650H

Stand

Desk

4-Screws

(not provided as parts of the product)

2-Screws, 2-Washers, 2-Nuts, 4-Rubbers

(provided as parts of the product)

G

You can select any type of attachment (Type 1 or Type 2)

G

Do not over tighten.

Type 1

Type 2

4-Screws

(not provided as parts of the product)

or

EXCEPT 47/55LD650H

PREPARATION

21

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact an installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

AA

BB

Model

VESA (A *B)

Standard Screw Quantity

Wall Mounting Bracket

(sold separately)

32 LG 710 H

37LG710H,

42LG 710H

32LD650H,

32LD655H

37LD650H,
37LD655H,
42LD650H,

42LD655H,

47LD650H

55LD650H

200* 10 0 M 4 4

200* 10 0 M 4 4

200* 200 M6 4

400* 400 M6 4

200* 200 M6 4

AA

BB

AW-47LG30M

LSW100B, LSW100BG

LSW200B, LSW200BG

LSW400B, LSW400BG,

DSW400BG

RW230 AW-47LG30M

PREPARATION

22

PREPARATION

GG

Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.

CAUTION

GG

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

GG

Standard dimensions for wall mount kits are shown
in the table.

GG

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

GG

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside of
the TV.

GG

For wall mounts that do not comply with the VESA
standard screw specifications, the length of the

screws may differ depending on their specifica­tions.

GG

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.

GG

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

PREPARATION

23

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the pic­ture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the

bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (sold separately) to tie the product. It is safer to
tie the rope so it becomes horizontal between the wall and the prod­uct.

■

You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

■

Image shown may differ from your TV.

GG

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.

GG

To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

NOTE

!

PREPARATION

24

PREPARATION

R

ANTENNA INANTENNA IN

M.P.I.

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

This image refers to using a Wall Antenna Socket or Outdoor
Antenna without a Cable Box Connection.

2. Cable

Wa ll
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75

Ω)

RF Coaxial Wire (75

Ω)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire
when connecting the antenna.

Copper Wire

- For optimum picture quality, adjust the antenna direction if needed.

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

■

To prevent damage, do not connect to the power outlet until all connections are made between the devices.

R

ANTENNA INANTENNA IN

M.P.I.

This image refers to using a cable connection without a cable box.

- If you experience a poor signal when using cable, make sure the RF cable is screwed in completely.
Contact your cable company is a poor signal persists.

PREPARATION

25

MPI CARD SLOT / PPV CARD INSTALLATION

(Except 47/55LD650H)

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

3. Detach RF cable.

4. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

5. Insert card all the way into the slot making sure it is fully seated into back plane connector.

6. Replace the two card retainer screws.

The MPI card is equipped with an RF jack for antenna/cable signal source connection.
This card can be removed and replaced with a third-party PPV (Pay-Per-View) card.

MPI Card Removal / PPV Card Installation

RF CABLE

ANTENNA IN

M.P.I.

M.P. I.

Card Slot

GG

There is an RF cable connected to the back of the card. Remove the card slowly.

WARNING

EXTERNAL EQUIPMENT SETUP

26

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP

This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,
if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as
shown below.

Component Connection

1. How to connect

Connect the video outputs (Y, PB

, P

R

)

of the digital set-

top box to the

CC OOMMPPOONNEENNTT II NN VV IIDDEEOO

jacks on

the TV. Match the jack colors (Y = green, P

B

= blue, and

P

R

= red).

Connect the audio output of the digital set-top box to
the

CC OOMMPPOONNEENNTT IINN AAUU DDIIOO

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

CC oo mmppoonn eenn tt

input source using the

IINN PP UUTT

button

on the remote control.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

U

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

R

(S

/

VIDEO

AUDIO

COMPONENT IN

RGB(PC)

AUDIO
(RGB/DVI)

RGB IN

TV-LINK

CFG

Y L RP

B

P

R

1

2

Y, C

B/P

B

, C

R/PR

Supported Resolutions

Horizontal Vertical

Frequency(kHz

)

Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

67.50 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

Signal

480i

480p

720p

10 8 0 i

10 8 0 p

Component

Yes

Yes

Yes

Yes

Yes

HDMI

No

Yes

Yes

Yes

Yes

For 37/42/47/55LD650H, 37/42LD655H

1920x1080p

For 37/42/47/55LD650H, 37/42LD655H

EXTERNAL EQUIPMENT SETUP

27

HDMI Connection

Connect the digital set-top box to

HHDDMMII//DD VVII IINN 11

((DDVVII)) or22

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDDMMII11

or

HHDDMMII22

input source with using the

IINNPPUUTT

button on the remote control.

2

1

HDMI-DTV

HDMI/DVI IN

2

1(DVI)

RJP

INTERFACE

VID

RGB

/

HDMI/DVI IN

2

1(DVI)

HDMI-DTV OUTPUT

1

Horizontal Vertical

Frequency(kHz)Frequency(Hz

)

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

26.97 23.94

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.939

67.50 60.00

Resolution

720x480p

1280x720p

1920x1080i

GG

If the HDMI cables don’t support High Speed
HDMI, it can cause flickers or no screen display. In
this case use the latest cables that support High
Speed HDMI.

GG

HDMI mode supports PCM, Dolby Digital audio
format.

NOTE

!

1920x1080p

For 37/42/47/55LD650H, 37/42LD655H

EXTERNAL EQUIPMENT SETUP

28

EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

RGB(PC)

AUDIO

(RGB/DVI)

RGB IN

UPDA

RESET

LAN

(SERVICE ONLY)

RJP

INTERFACE

COMPONENT IN

VIDEO

AUDIO

R

(S

/

HDMI/DVI IN

2

1(DVI)

LR

DVI-DTV OUTPUT

L

R

TV-LINK

CFG

CO

1

2

GG

A DVI to HDMI cable or adapter is required for this
connection. DVI doesn't support audio, so a separate
audio connection is necessary.

NOTE

!

Connect the DVI output of the digital set-top box to
the

HHDDMMII//DDVVII IINN 11 ((DD VVII ))

jack on the TV.

Connect the audio output of the digital set-top box to
the

AAUU DDIIOO (( RRGGBB//DD VVII ))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s man­ual for the digital set-top box.

)

■

Select the

HHDD MMII11

input source on the TV using the

IINNPP UUTT

button on the remote control.

2

1

EXTERNAL EQUIPMENT SETUP

29

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBP

R

Video output ports

on DVD player

Y

Y

Y

Y

P

B

B-Y

Cb

Pb

P

R

R-Y

Cr

Pr

Connect the video outputs (Y, P

B, PR

)

of the DVD to the

CC OOMMPPOONNEENNTT IINN VVIIDDEEOO

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and P

R = red

)

.

Connect the audio outputs of the DVD to the
CC OOMMPPOONNEENNTT IINN AAUU DDIIOO

jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

CC oo mmppoonn eenn tt

input source on the TV using the

IINN PPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

U

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

R

(S

/

VIDEO

AUDIO

COMPONENT IN

RGB(PC)

AUDIO
(RGB/DVI)

RGB IN

TV-LINK

CFG

Y L RP

B

P

R

1 2

HDMI Connection

Connect the HDMI output of the DVD to the
HHDDMMII//DDVVII IINN 11 ((DD VVII )) or22

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HHDDMMII11 orHHDDMMII22

input source on the TV

using the

IINN PPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

(S

HDMI/DVI IN

2

1(DVI)

RJP

INTERFACE

COM

VIDEO

/

HDMI/DVI IN

2

1(DVI)

HDMI OUTPUT

RGB IN

1

EXTERNAL EQUIPMENT SETUP

30

EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUP

VCR SETUP

Antenna Connection

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

/

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

ANTENNA INANTENNA IN

M.P.I.

Wall Jack

Antenna

1

2

Connect the RF antenna out socket of the
VCR to the

AANNTTEENNNNAA IINN

socket on the

TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

Composite (RCA) Connection

Connect the

AA UUDD IIOO/VV IIDDEEOO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

)

■

Select the

AA VV 11

input source on the TV using the

IINN PPUUTT

button on the remote control.

■

If connected to

AAVV IINN 22

, select

AAVV22

input source on the TV.

1

GG

If you have a mono VCR, connect the audio cable
from the VCR to the

AAUUDDIIOO LL// MMOONNOO

jack of the

TV.

NOTE

!

L

R

S-VIDEO

VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

OPTICAL

DIGITAL

AUDIO OUT

UPDATE

AV IN 1

AUDIO

VIDEO

/

REMOTE
CONTROL

OUT

SPEAKER

OUT

8

RS-232C IN

(SERVICE ONLY)

MONO

/

AV IN 1

AUDIO

VIDEO

MONO

/

GAME

CONTROL

1