LG 43UV340C, 43UV340H, 49UV340C, 49UV340H, 75UV340C User Manual

...

OWNER’S MANUAL

Safety and Reference

LED TV*

* LG LED TVs are LCD TVs with LED backlighting.

Please read this manual carefully before operating your TV and retain it for future reference.

43UV340C 43UV340H

49UV340C 49UV340H

*MFL69885532*

55UV340C 55UV340H

65UV340C 65UV340H

75UV340C

www.lg.com

P/NO : MFL69885532 (1705-REV00)

Warning! Important Safety instructions

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user

to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user

to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the device.

ENGLISH

WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

• Do not install near any heat sources such

as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on

or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by

the manufacturer.

• Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms

or when unused for long periods of time.

• Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• Do not press strongly upon the panel with a

hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it.

• Do not stick metal objects or any other

conductive material into the power cord. Do not touch the end of the power cord while it is plugged in.

• Keep the packing anti-moisture material or

vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed, induce vomiting and go to the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.

• Concerning the Power Cord (Can differ by

country): Check the specification page of this owner’s manual to be certain concerning current requirements. Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your device, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the device, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device. Do not move the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• To reduce the risk of fire or electrical shock,

do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

• Do not use high voltage electrical equipment

near the TV (e.g., a bug zapper). This may result in product malfunction.

• Do not expose to dripping or splashing and

do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

• Grounding (Except for devices which are not

grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.

• As long as this unit is connected to the AC wall

outlet, it is not disconnected from the AC power source even if the unit is turned off.

• Do not attempt to modify this product in any

way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

• Outdoor Antenna Grounding (Can differ by

country): If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.Antenna grounding according to the

National Electrical Code, ANSI/NFPA 70

• Moving Make sure the product is turned off,

unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.

• Ventilation Install your TV where there is proper

ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places.

• Take care not to touch the ventilation openings.

When watching the TV for a long period, the ventilation openings may become hot. This does not affect the performance of the product or cause defects in the product.

• If you smell smoke or other odors coming from

the TV, unplug the power cord and contact an authorized service center.

• If water or another substance enters the

product (like an AC adapter, power cord, or TV), disconnect the power cord and contact the service center immediately. Otherwise, this may result in fire or electric shock.

• Do not install this product on a wall if it could be

exposed to oil or oil mist. This may damage the product and cause it to fall.

• Use only an authorized AC adapter and power

cord approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product deformation.

• Never disassemble the AC adapter or power

cord. This may result in fire or electric shock.

• Handle the adapter carefully to avoid dropping

or striking it. An impact could damage the adapter.

• Keep the product away from direct sunlight.

• Never touch this apparatus or antenna during a

lightning storm.

ENGLISH

• When mounting a TV on the wall, make sure not

to install the TV by hanging the power and signal cables on the back of the TV.

• Do not allow an impact shock, any objects to fall

into the product, and do not drop anything onto the screen.

• DISCONNECTING THE DEVICE FROM THE MAIN

POWER The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

• Make sure the power cord is connected securely

to the power plug on the TV.

• Batteries Store the accessories (battery, etc.) in a

safe location out of the reach of children.

• This apparatus uses batteries. In your community

there might be regulations that require you to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.

• Do not dispose of batteries in a fire.

• Do not short circuit, disassemble, or allow the

batteries to overheat.

• Cleaning When cleaning, unplug the power

cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids

ENGLISH

directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners, or benzene.

Preparing

• When the TV is turned on for the first time after

being shipped from the factory, initialization of the TV may take approximately one minute.

• Image shown may differ from your TV.

• Your TV’s OSD (On Screen Display) may differ

slightly from that shown in this manual.

• The available menus and options may differ from

the input source or product model that you are using.

• New features may be added to this TV in the

future.

• The items supplied with your product may vary

depending upon the model.

• Product specifications or contents of this manual

may be changed without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and

USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) width.

• Use an extension cable that supports USB 2.0 if

the USB cable or USB flash drive does not fit into your TV’s USB port.

• Use a certified cable with the HDMI logo

attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.

• Recommended HDMI cable types (3 m or less)

- High-Speed HDMI®/™ cable

- High-Speed HDMI®/™ cable with Ethernet

*A 10 mm (0.39 inches)

*B 18 mm (0.7 inches)

• Do not use any unapproved items to ensure the

safety and lifespan of the product.

• Any damages or injuries by using unapproved

items are not covered by the warranty.

• Some models appear to have a thin film on the

screen. It is actually part of the screen; do not remove it.

• When attaching the stand to the TV set, place

the screen facing down on a cushioned table or flat surface to protect the screen from scratches. (Depending upon model)

• Make sure that the screws are fastened tightly.

(If they are not fastened securely enough, the TV may tilt forward after being installed.)

• Do not fasten the screws with excessive force

otherwise they may be worn out and become loose.

• Make sure to wring any excess water or cleaner

from the cloth.

• Do not spray water or cleaner directly onto the

TV screen.

• Make sure to spray just enough of water or

cleaner onto a dry cloth to wipe the screen.

• When handling the TV, be careful not to damage

the protruding buttons.

• Avoid touching the screen at all times, as

this may result in damage to the screen.

• Do not place the product on the floor with

its front facing down without padding. Failure to do so may result in damage to the screen.

• Do not move the TV by holding the cable

holders, as the cable holders may break, and injuries and damage to the TV may occur. (Depending upon model)

Using the Button

Lifting and Moving the TV

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or

packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the

power cord and all cables.

• When holding the TV, the screen

should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly.

Make sure not to hold the transparent part, speaker, or speaker grille area.

• Use at least two people to move

a large TV.

• When transporting the TV by

hand, hold the TV as shown in the following illustration.

• When transporting the TV, do not expose the TV

to jolts or excessive vibration.

• When transporting the TV, keep the TV upright;

never turn the TV on its side or tilt towards the left or right.

You can operate the TV functions, using the button.

ENGLISH

Basic Functions

Power On (Press)

Power Off 1 (Press and Hold)

Menu control (Press 2)

Menu selection (Press and Hold 3)

1 All running apps will close.

2 You can access and adjust the menu by pressing

the button when TV is on.

3 You can use the function when you access menu

control.

Adjusting the Menu

When the TV is turned on, press the button one time. You can adjust the Menu items using the buttons.

Turns the power off.

Changes the input source.

Scrolls through the saved channels.

Adjusts the volume level.

Mounting on a Table

Adjusting the Angle of the TV to Suit View

(Depending upon model)

Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view.

20˚20˚

(Depending upon model)

1 Lift and tilt the TV into its upright position on a

table.

- Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation.

ENGLISH

10 cm

(4 inches)

10 cm

2 Connect the power cord to a wall outlet.

• Do not place the TV near or on sources

of heat, as this may result in fire or other damage.

• Do not apply foreign substances (oils,

lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.)

10 cm

• When adjusting the angle of the TV, watch

out for your fingers.

- Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury.

Attaching the TV to a desk (optional)

(Depending upon model)

If mounting the TV on a table, make sure it is installed according to the method outlined in ‘Attaching the TV to a desk’.

The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.

4-Screws

(Not provided as parts of the product.)

Stand

Desk

Using the kensington security system (optional)

The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com. Connect the Kensington security system cable between the TV and a table.

• The Kensington security system is optional. You

can obtain additional accessories from your local dealer.

Securing the TV to a Wall (optional)

(Depending upon model)

Mounting on a Wall

An optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount. Detailed instructions will be included with the wall mount. We recommend that you use an LG brand wall mount. The LG wall mount is easy to adjust or to connect the cables. When you do not use LG’s wall mount bracket, use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. If you are using a non-adjustable mount, attach the mount to the wall. Attach the cables to the TV first, then attach the TV to the mount.

10 cm

(4 inches)

10 cm

ENGLISH

1 Insert and tighten the eye-bolts or TV brackets

and bolts on the back of the TV.

- If there are bolts inserted at the eye-bolts position, remove the bolts first.

2 Mount the wall brackets with the bolts to the

wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3 Connect the eye-bolts and wall brackets tightly

with a sturdy rope or cable. Make sure to keep the rope parallel to the flat surface.

• Make sure that children do not climb on or

hang on the TV.

• Use a platform or cabinet that is strong and

large enough to support the TV securely.

• Brackets, bolts, and ropes are optional. You

can obtain additional accessories from your local dealer.

Make sure to use screws and wall mounts that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.

Model

VESA (A x B) 200 x 200 300 x 300 Standard screw M6 M6 Number of screws 4 4 Wall mount bracket

(optional)

43UV340C 43UV340H

LSW240B MSW240

49UV340C 49UV340H 55UV340C 55UV340H

LSW350B MSW240

Model

VESA (A x B) 300 x 300 600 x 400 Standard screw M6 M8 Number of screws 4 4 Wall mount bracket

(optional)

65UV340C 65UV340H

LSW350B LSW640B

• Remove the stand before installing the TV

on a wall mount by performing the stand attachment in reverse.

• When using the wall mount, it is recommended

that you apply a piece of tape over the Stand holes to prevent dust and bugs from entering the holes. (Depending upon model)

ENGLISH

Stand Hole

75UV340C

Connections (Notifications)

You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device.

• If you record a TV program on a DVD recorder or

VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information about recording, refer to the manual provided with the connected device.

• The external device connections shown may

differ slightly from illustrations in a manual.

• Connect external devices to the TV regardless

about the order of the TV port.

• If you connect a gaming device to the TV, use the

cable supplied with the gaming device.

• Refer to the external equipment’s manual for

operating instructions.

• In PC mode, there may be noise associated

with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the Picture menu until the picture is clear. Depending upon the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.

• Some USB Hubs may not work. If a USB device

connected through a USB Hub is not detected, connect it directly to the USB port on the TV.

• When connecting via a wired LAN, it is

recommended to use a CAT 7 cable.

Connecting to an Antenna or Cable

Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may differ from the actual items and an RF cable is optional.

• Make sure not to bend the copper wire of the RF

cable.

Copper wire

• Complete all connections between devices, and

then connect the power cord to the power outlet to prevent damage to your TV.

• Use a signal splitter to use 2 TVs or more.

• DTV Audio Supported Codec: MPEG, Dolby

Digital

• This TV cannot receive ULTRA HD (3840 x 2160

pixels) broadcasts directly because the related

standards have not been confirmed. (Depending upon model)

Other Connections

Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable.

• > > General > HDMI ULTRA HD

Deep Color:

- On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)

- Off : Support 4K @ 60 Hz 8bit (4:2:0)

• If the device connected to Input Port also

supports ULTRA HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, connect the device to a different HDMI port or change the TV ’s HDMI ULTRA HD Deep Color setting to off.

• HDMI Audio Supported Format: DTS (44.1 kHz /

48 kHz), Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz), PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz) (Depending upon model)

• Use only with the 3 pole 3.5 mm stereo jack.

• Do not connect your headphones or earphones

to the port for connecting an external speaker.

Remote Control

(Some buttons and services may not be provided depending upon models or regions.)

The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To install batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. Failure to match the correct polarities of the batteries may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution. To remove the batteries, perform the installation actions in reverse. This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.

(Power) Turns the TV on or off.

Returns to the last TV channel.

Activates or deactivates the subtitles.

Not functional.

Resizes an image.

Changes the input source.

Number button Enters numbers.

(Dash) Inserts a dash between numbers such as

2-1 and 2-2.

Accesses the saved channel list.

Alternates between the two last

channels selected (pressing repeatedly).

Adjusts the volume level.

Accesses your favorite channel list.

Digital signal: Changes the audio language.

Analog signal: Changes the MTS sound.

Mutes all sounds.

• Pressing and holding the button

displays the Accessibility menu.

Scrolls through the saved channels.

Moves to the previous or next screen

ENGLISH

Changes the picture mode.

ENGLISH

Shows information on the current

program.

Changes the sound mode.

Accesses the setting menu.

Accesses the quick menu.

Navigation button (up / down / left / right)

Scrolls through menus or options.

Selects menus or options and confirms your

input.

Returns to the previous screen.

Clears all on-screen displays and returns to

TV viewing.

Enables SAP (Secondary Audio Program)

Feature.

Sets the length of time until the TV to turns

off.

, , , , Control buttons for media contents

These access special functions in

some menus.

Settings

To select Picture Mode

• Picture • Picture Mode Settings • Picture

Mode

Select the picture mode optimized for the viewing environment or the program.

• Vivid Heightens contrast, brightness, and

sharpness to display vivid images.

• Standard Displays images in standard levels of

contrast, brightness and sharpness.

• APS APS (Auto power saving) mode reduces

power consumption by dimming control.

• Cinema / Game Displays the optimum picture

for movie or game.

• Sports Optimised picture mode for football

matches. The pitch and kits are presented in vibrant colours, with crystal-clear images even for fast movements.

• HDR Effect This feature lets you enjoy a more

dynamic, clearer image by correcting the light and dark areas of the display. This feature provides a realistic image, even when the source image’s gradation level is high. If you set Picture Mode to HDR Effect, you will not be able to use some of Picture Mode Settings.

• Expert Menu for adjusting picture quality that

allows experts and amateurs to enjoy the best TV viewing. This menu for adjustment is provided for ISF-certified picture tuning professionals. (ISF logo can be used only on ISF-certified TVs.) ISFccc: Imaging Science Foundation Certified Calibration Control

• Depending upon the input signal, the available

range of picture modes may differ.

• Expert mode is for picture tuning professionals

to control and fine-tune using a specific image. For normal images, the effects may not be drastic.

• Picture Mode change may modify Energy

Saving and Motion Eye Care settings and it can affect energy consumption.

To set additional picture options

• Picture • Picture Mode Settings • Picture

Options

Adjusts detailed setting for images.

• Noise Reduction Eliminates noise in the picture.

• MPEG Noise Reduction Eliminates noise

generated while creating digital picture signals.

• Black Level Adjusts the brightness and contrast

of the screen to suit the black level.

• Real Cinema Optimizes the screen for movie

viewing.

• Motion Eye Care Automatically adjusts

brightness and reduces image blur based on image data to reduce eyestrain.

• LED Local Dimming

Maximizes the contrast ratio by making the bright areas of the screen brighter and the dark areas of the screen darker.

- Off : Disables the LED Local Dimming function.

- Low / Medium / High : Changes the contrast ratio.

Turning this option Off may increase energy consumption.

• TruMotion Corrects images to display smoother

motion sequences. Auto means juddering and blurring range that depend on input video status is controlled by TruMotion mode.

• Depending upon input signal or other picture

settings, the range of detailed items for adjustment may differ.

To use energy saving feature

• Picture • Energy Saving

Reduces power consumption by adjusting peak screen brightness.

• Auto The TV sensor detects the ambient lighting

and automatically adjusts the screen brightness.

• Off Turns off the Energy Saving.

• Minimum / Medium / Maximum Applies the

pre-set Energy Saving.

• Screen Off Screen is turned off and only sound is

played. Press any button on the remote control to turn the screen back on.

• Depending on the Energy Saving (Auto /

Maximum), you may not be able to adjust the Backlight. In this case, navigate to • Picture

• Energy Saving and set to Off or Minimum.

Licenses

Supported licenses may differ by model. For more information about licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

(Depending upon model)

ENGLISH

Open Source Software Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.

Troubleshooting

The software may be updated for improvement in performance. The customer is responsible to ensure the compatibility of their equipment with

ENGLISH

any LG Electronics software. If needed, please consult with LG Electronics and update new software versions according to the guidance provided by LG Electronics.

• Cannot control the TV with the remote control.

- Check if anything such as tape has been placed over the receiver.

- Check if there is any obstacle between the product and the remote control.

- Replace the batteries with new fresh ones.

• No image display and no sound is produced.

- Check if the product is turned on.

- Check if the power cord is connected to a wall outlet.

- Check if there is a problem in the wall outlet by connecting other products.

• The TV turns off suddenly.

- Check the power control settings.

- The power supply may be interrupted.

- Check if the Timer Power Off / Sleep Timer feature is activated in the Timers settings.

- If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

• Abnormal Display

- If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

- This panel is an advanced product that contains millions of pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

- Displaying a still image for a prolonged period of time may cause an image sticking. Avoid displaying a fixed image on the TV screen for a extended length of time.

• Generated Sound

- Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

- Electrical circuit humming/panel buzzing A low level noise is generated from a highspeed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

Specifications

Product specifications may be changed without prior notice due to upgrade of product functions.

Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only).

The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).

Television System

ATSC, NTSC-M, 64 & 256 QAM

Program Coverage

VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135

External Antenna Impedance

75 Ω

Environment condition

• Operating Temperature

0 °C to 40 °C (32 °F to 104 °F)

• Operating Humidity

Less than 80 %

• Storage Temperature

-20 °C to 60 °C (-4 °F to 140 °F)

• Storage Humidity

Less than 85 %

HDMI (PC) supported mode

Resolution

640 x 350 31.46 70.09 720 x 400 31.46 70.08 640 x 480 31.46 59.94 800 x 600 37.87 60.31 1024 x 768 48.36 60.00 1360 x 768 47.71 60.01 1152 x 864 54.34 60.05 1280 x 1024 63.98 60.02

1920 x 1080

3840 x 2160

4096 x 2160

Horizontal Frequency (kHz)

67.50 60.00

135.00 120.00

54.00 24.00

56.25 25.00

67.50 30.00

53.95 23.97

54.00 24.00

Vertical Frequency (Hz)

HDMI (DTV) supported mode

Resolution

640 x 480p

720 x 480p

720 x 480i 15.75 60.00 720 x 576p 31.25 50.00 720 x 576i 15.62 50.00

1280 x 720p

1920 x 1080i

1920 x 1080p

3840 x 2160p

4096 x 2160p

• The optimal display resolution

- 3840 X 2160

Horizontal Frequency (kHz)

31.46 59.94

31.50 60.00

31.47 59.94

31.50 60.00

37.50 50.00

44.96 59.94

45.00 60.00

28.12 50.00

33.72 59.94

33.75 60.00

26.97 23.97

27.00 24.00

33.71 29.97

33.75 30.00

56.25 50.00

67.43 59.94

67.50 60.00

112.50 100.00

134.86 119.88

135.00 120.00

53.95 23.98

54.00 24.00

56.25 25.00

61.43 29.97

67.50 30.00

112.50 50.00

134.86 59.94

135.00 60.00

53.95 23.98

54.00 24.00

56.25 25.00

61.43 29.97

67.50 30.00

112.50 50.00

134.86 59.94

135.00 60.00

Vertical Frequency (Hz)

ENGLISH

Component port connecting information

(Depending upon model)

Component ports on the TV

Video output ports on DVD player

Component supported mode

Resolution

720 x 480i

Horizontal Frequency (kHz)

15.73 59.94

15.75 60.00

720 x 576i 15.62 50.00

720 x 480p

31.47 59.94

31.50 60.00

720 x 576p 31.25 50.00

44.96 59.94

1280 x 720p

45.00 60.00

37.50 50.00

ENGLISH

1920 x 1080i

28.12 50.00

33.72 59.94

33.75 60.00

56.25 50

1920 x 1080p

67.43 59.94

67.50 60.00

Vertical Frequency (Hz)

Supported Photo Formats

File Format Format Resolution

Minimum: 64 x 64,

.jpeg, .jpg,

.jpe

.png PNG

.bmp BMP

Maximum: Normal Type:

JPEG

15,360 (W) x 8,640 (H), Progressive Type: 1,920 (W) x 1,440 (H)

Minimum: 64 x 64, Maximum: 5,760 (W) x 5,760 (H)

Minimum: 64 x 64, Maximum: 1,920 (W) x 1,080 (H)

Y PBP

Y PBP Y B-Y R-Y Y Cb Cr Y Pb Pr

Supported Audio Formats

File Format Info

.mp3

[Bit rate] 32 Kbps ~ 320 Kbps [Sample freq.] 16 kHz ~ 48 kHz [Support] MPEG-1, MPEG-2 [Channels] mono, stereo

[Bit rate] Free Format

.wav

[Sample freq.] 8 kHz ~ 96 kHz [Support] PCM [Channels] mono, stereo

[Bit rate] 64 Kbps ~ 320 Kbps

.ogg

[Sample freq.] 8 kHz ~ 48 kHz [Support] Vorbis [Channels] mono, stereo

[Bit rate] 128 Kbps ~ 320 Kbps

.wma

[Sample freq.] 8 kHz ~ 48 kHz [Support] WMA [Channels] up to 6 ch

[Bit rate] Free Format

.flac

[Sample freq.] 8 kHz ~ 96 kHz [Support] FLAC [Channels] mono, stereo

Supported Video Formats

Extension Codec

VC-1 Advanced Profile

Video

(Except for WMVA), VC-1

.asf, .wmv

.avi

.mp4, .m4v,

.mov

.3gp, .3g2

.mkv

.ts, .trp,

.tp, .mts

.mpg,

.mpeg,

.dat

Simple and Main Profiles WMA Standard (except for

Audio

WMA v1/ WMA Speech) Xvid (except for 3 warp-point

Video

GMC), H.264/AVC, Motion Jpeg, MPEG-4

MPEG-1 Layer I, II, MPEG-1

Audio

Layer III (MP3), Dolby Digital, LPCM, ADPCM, DTS

Video H.264/AVC, MPEG-4, HEVC

Dolby Digital, Dolby Digital

Audio

Plus, AAC, MPEG-1 Layer III

(MP3) Video H.264/AVC, MPEG-4 Audio AAC, AMR-NB, AMR-WB

MPEG-2, MPEG-4, H.264/AVC, Video

VP8, VP9, HEVC

Dolby Digital, Dolby Digital

Plus, AAC, PCM, DTS, MPEG-1 Audio

Layer I, II, MPEG-1 Layer III

(MP3) Video H.264/AVC, MPEG-2, HEVC

MPEG-1 Layer I, II, MPEG-1 Audio

Layer III (MP3), Dolby Digital,

Dolby Digital Plus, AAC, PCM Video MPEG-1, MPEG-2

MPEG-1 Layer I, II, MPEG-1 Audio

Layer III (MP3)

.vob

.rm, .rmvb

.mkv,

.mp4, .ts

Video MPEG-1, MPEG-2

Dolby Digital, MPEG-1 Layer I,

Audio

II, DVD-LPCM

Video RV30, RV40

Realaudio6 (cook), AAC LC,

Audio

HE-AAC

Video H.264/AVC, HEVC

Dolby Digital, Dolby Digital

Audio

Plus, AAC

Regulatory

FCC NOTICE

(For USA)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radio Frequency Interference Requirements (for UNII devices)

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter.

FCC RF Radiation Exposure Statement

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the radiator and your body. Users must follow the specific operating instructions for satisfying RF exposure compliance.

Industry Canada Statement

(For Canada) [For having wireless function (WLAN, Bluetooth,...)]

This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

ENGLISH

+ 34 hidden pages