LG 43UT661H0GA INSTALLATION MANUAL

INSTALLATION MANUAL

LED TV*

* LG LED TV applies LCD screen with LED backlights.

Please read this manual carefully before operating your set and retain it for future reference.

UT78**

UT76**

UT66**

UT64**

LT66**

ET96**

*MFL70423711*

www.lg.com

(1905-REV00)

Copyright © 2019 LG Electronics Inc. All Rights Reserved.

<![if ! IE]>

<![endif]>ENGLISH

	2
	Table of contents			27	-	Server Settings
				27	-	Ping Test
				28	Pro:Centric
	4	Location and Function of Controls		28	-	Mode
				28	-	WORF
	4	Parts and Button
				28	-	Room Number Setting
	4	Basic functions		28	-	Media Type
	5	LED Clock Connection		29	-	Receive Data
				29	-	Native EPG
	6	First Use Wizard		30	General
				30	-	Configuration Setup
	7	Basic Settings
				35	-	External Speaker
	7	-	Language & Location	35	-	Set ID Setup
	8	-	Network Settings	35	-	Power Saving
	9	-	Portal Settings	36	-	HCEC Setup
	10	-	Voice Service Coverage	37	-	Clock Setup
	11	Data Cloning		37	-	Password Change
	11	Solution Settings		38	-	Lock Mode
	11	- Language & Location selection		38	-	Crestron
	12	-	Automatically for Setup	38	-	Welcome Video Mode
	16	-	Manually for Setup	38	-	Developer Mode
	19	Installation Menu Settings		39	Portal Settings
	19	Access Installation menu for commercial feature		39	-	Portal Mode
		settings.		39	-	Auto Start
				39	-	PreLoaded App
	20	Installation Menu		40	-	Website Shortcut
				40	-	Input Shortcut
	20	Introduction		41	-	Hotel Directory
	21	LG Hotel Mode		41	-	Portal Editor
				41	-	Portal Manager
	21	-	Hotel Mode Operation
				44	Media Share
	21	-	Power On Status
	22	-	Volume	44	-	SmartShare
	22	-	Key Management	44	-	Screen Share
	23	-	Limited Mode	44	-	Media Renderer
	23	-	DTV Programme Update	44	-	DIAL
	24	-	Power On Default	44	-	TV Name
	24	-	Aux Source Setting	45	-	SoftAP
	24	-	Power Management	46	-	Beacon
	24	-	Radio Video Blank	47	TV Manager
	24	-	Factory Reset	47	-	Diagnostics
	25	Network		52	-	USB Download Menu
	25	-	MAC Address	57	CONTENT MANAGER
	25	-	Network Settings	57	-	Web Login
	26	-	LG Connect
	26	-	IP Stream Control
	26	-	Wake On LAN
	26	-	VLAN ID

57 - Content Manager

61 - Group Manager 2.0

63IR Codes

64External control device Setup

64RS-232C Setup

64Phone jack Type

64Type of Connector : D-Sub 9-Pin Male

65RS-232C Configurations

65 Communication Parameters

65 IR OUT Using Guide

65- Suitable / Not Recommend remote-controller data format

65- IR Receiver specifications

66Command Reference List

67Transmission / Receiving Protocol

3

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

4

Location and Function of Controls

Parts and Button

Basic functions

Power On (Press)

Power Off1 (Press and Hold)

Menu Control (Press2)

Menu Selection (Press and Hold3)

1All running apps will close.

2You can access and adjust the menu by pressing the button when TV is on.

3You can use the function when you access menu control.

LED Clock Connection

(Depending on model)

This TV can be connected to a LED Clock via the CLOCK port.

CLOCK

LED Clock

(*Not Provided)

5

First Use Wizard

* Images shown may differ from your TV.

(Depending on model)

•• There are four options - Basic Settings, Data Cloning, Solution Settings, and Installation Menu Settings. Each menu can access by START button.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

6

Basic Settings

(Depending on model)

This menu is for basic settings related to language, network, portal, voice service coverage and programme tuning without SI (Pro:Centric) setting. There are four steps for it.

Language & Location

(Depending on model)

•• Select the Language and Country. Some countries need to select the Time Zone.

Network Settings

(Depending on model)

•• Set Network connection. You can connect easily to wired/wireless network. (“Network Settings”on page 24)

7

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

8

Portal Settings

(Depending on model)

•• Set the Portal Mode and Portal Auto Start.

Portal Mode

(Depending on model)

•• You can select ‘Default Portal’(Use webOS default portal), ‘Customizable Portal’(Use editable Portal), or ‘None’(Do not use portal).

Portal Auto Start

•• You can select ‘On’or ‘Off’. If you select ‘On’, Portal (Home Launcher) will be execute automatically after TV on.

Voice Service Coverage

(Depending on model)

•• Set the voice service coverage. You can set LG Service Country and Service Area Postcode(Depending on model) for voice service.

9

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

10

Data Cloning

(Depending on model)

Access Data cloning menu of TV Manager application for applying cloning file.

Solution Settings

(Depending on model)

The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. If TV doesn’t contact the Server, TV will search the pre-defined programme earlier than all programmes. (Only DVB-C)

The frequencies of pre-defined programmes are below.

•• Germany: ‘51000, 858000, 778000, 698000, 618000, 538000, 458000, 378000, 298000, 218000, 138000 khz’.

•• Philippines 6 Mhz: ‘57000, 651000, 591000, 531000, 471000, 411000, 351000, 291000, 231000, 171000, 111000 khz’.

•• Other Country: ‘50000, 842000, 762000, 682000, 602000, 522000, 442000, 362000, 282000, 202000, 122000 khz’.

Language & Location selection

(Depending on model)

•• Please select the Language and Country. Some countries need to select the Time Zone.

11

Automatically for Setup

(Depending on model)

1From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. Also, you can configure the network environment.

•• Complete initial download of maintenance(On/Off Toggle): you can choose the option whether to skip the maintenance files download during the EZ-Manager process.

•• If you intend to set Room Number as part of the TV configuration, use the Room Number option to assign the Room # for this TV before you continue with additional configuration.

•• In the Label field, use the Left/Right arrow keys to specify a North, South, East, or West designation for this TV.

•• In the Room Number field, you can use the number keys on the Installation Remote to direct enter a room number or use the virtual keyboard on the TV screen.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

12

•• If you intend to apply the files via USB, use USB Configuration option to access TV Manager app. (“TV Manager”on page 46)

•• To continue, move and select NEXT.

•• If you intend to set network, use the Network Settings option. You can connect easily to wired/wireless network by this option. (“Network Settings”on page 24)

13

2 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data programme, select the NEXT.

<![if ! IE]>

<![endif]>ENGLISH

14

3 Downloading the Pro:Centric application files takes few minutes.

<![if ! IE]>

<![endif]>ENGLISH

4 After the installation is completed, the following screen will be displayed.

15

Manually for Setup

(Depending on model)

1Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select NEXT.

2 Please select the MANUAL PRO:CENTRIC.

<![if ! IE]>

<![endif]>ENGLISH

16

3 Configure the appropriate Pro:Centric settings in the TV. (Taiwan does not support RF)

<![if ! IE]>

<![endif]>ENGLISH

17

<![if ! IE]>

<![endif]>ENGLISH

4 Downloading the Pro:Centric application files takes few minutes.

18

5 After the installation is completed, the following screen will be displayed.

<![if ! IE]>

<![endif]>ENGLISH

Installation Menu Settings

(Depending on model)

Access Installation menu for commercial feature settings.

19

Installation Menu

* Images shown may differ from your TV.

Introduction

The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’.

The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.

<![if ! IE]>

<![endif]>ENGLISH

1Press the Setting button for more than 5 seconds using the user remote control, banner will appear at top left on the screen.

2Enter a four digit password and press button. -- The TV is set with the initial password “1-1-0-5”.

20

LG Hotel Mode

<![if ! IE]>

<![endif]>ENGLISH

When ‘Hotel Mode Operation’ is set to On, all functions of Hotel Mode apply.

Hotel Mode Operation

(Depending on model)

•• Decide to work all functions of ‘Hotel Mode Operation’or not.

•• When ‘Hotel Mode Operation’is set to On, all functions of Hotel Mode apply.

•• When ‘Hotel Mode Operation’is set to Off, all functions of Hotel Mode Do Not apply.

Power On Status

•• Decide to select working status of TV Set when turn on main power.

•• You can select PWR, STD, LST.

•• PWR always make TV set On status when turn on main power.

•• STD make Stand-by status when turn on main power.

•• LST make TVSet work like previous power status. As same concept as Power Backup mode; If main power were turned off in Power On status, TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in Stand-by status.

•• If there Block All is both IR Operation and Local Key Operation from Key Management, In order to provide the Option that must be able to turn on the TV in the TV turned off situation, change the value of the PWR. (Reference the Key Management)

21

Volume

•• Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’and ‘Minimum Volume’as On or Off.

•• (0 ≤ Min ≤ Start ≤ Max ≤ 100)

Start Volume

•• This entry sets the start volume level when is power on.

-- The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max) -- The default setting is ‘Off’.

-- When selected to 'On', if the value is lower then the minimum specified in the minimum volume entry, the minimum volume entry must be used.

-- When selected to 'On', if the value is larger then the maximum specified in the maximum volume entry, the maximum volume value must be used.

-- Access to a volume in ‘Timer Power On’ must be fixed to start volume when ‘Hotel Mode Operation’ (On) and ‘Start Volume’ (Off, 0 ~ 100) were set simultaneously.

Maximum Volume

•• This entry sets the maximum volume level the set. The level is specified as a number between ‘Minimum Volume’to 100. (Min ≤ Max ≤ 100). -- The default value is 100.

Minimum Volume

•• This entry sets the minimum volume level the set. The level is specified as a number between 0 to ‘Maximum Volume’. (0 ≤ Min ≤ Max) -- The default value is 0.

Key Management

•• Manage key usability of Local(Front) Key and Remote Control. When selected to ‘On’, following ‘IR Operation’and ‘Local Key Operation’will be worked by below.

IR Operation

•• Decide whether work the LG remote control or not.

-- When ‘IR Operation’ is set to 'Normal', all remote keys are available. -- 'Use PWR Only' makes block all remote keys except power key.

-- When ‘IR Operation’ is set to 'Block All', all normal remote keys don’t work.

Local Key Operation

•• Decide to operate 'Local Key' working behavior.

-- When ‘Local Key Operation’ is set to 'Normal', all local keys are available. -- 'Use PWR Only' makes block all local keys except power key.

-- When ‘Local Key Operation’ is set to 'Block All', all local keys don’t work.

<![if ! IE]>

<![endif]>ENGLISH

<![if ! IE]>

<![endif]>ENGLISH

22

Limited Mode

•• Configure TV function’s limitation. When selected to ‘On’, following sub-menus will be worked by below.

Setup Menu

•• Permit to tune and manage programmes.

Programme Change

(Depending on model)

•• Decide to change programme or not by setting ‘Programme Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV.

Menu Display

•• Function to decide whether work with menu of control key or not.

-- Although select Off, the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ is available. -- When select On, Menu works.

OSD Display

•• Decide to display OSD or not.

-- When set to ‘Off’, all OSD is not displayed except some exception.

-- Although select ‘Off’, the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ and entering service menu are available. (In-Start, Power-Only, Adjust, Installation Menu...)

System Provider Mode

•• ‘System Provider Mode’allows access to the menu system from the front panel or remote control but access is controlled as follows: -- When value is ‘On’, Accessible Items on the menu system, others are not permissible. (Depending on model)

»» Input select screens »» Sleep timer

»» Aspect Ratio »» Subtitles

»» Programmes (Except for Programme Tuning & Settings and Programme Manager)

DTV Programme Update

•• It is a mode to set whether to update DTV Programme automatically or not.

•• When set to ‘Auto’, the function to update TV’s programme map according to DTV programme’s stream information.

•• When set to ‘Manual’, DTV Programme Update is set to ‘Manual’, the function to keep TV’s programme map even though DTV programme’s information is changed.