LG 43LU340C INSTALLATION MANUAL
INSTALLATION MANUAL
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
LU34**-Z/T*
LU54**-T*
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
www.lg.com
TABLE OF CONTENTS
ENGLISH
3 INSTALLATION MENU
3 Introduction
4 LG HOTEL MODE SETUP
4 (1) Hotel Mode Operation (DVB)
4 (2) Power On Status
5 (3) Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)
5 - (3-1) Start Volume
5 - (3-2) Maximum Volume
5 - (3-3) Minimum Volume
6 (4) Key Operation
6 - (4-1) IR Operation
6 - (4-2) Local Key Operation
7 (5) Limited Mode
7 - (5-1) Setup Menu
7 - (5-2) Input Source Change
7 - (5-3) Programme Change
7 - (5-4) Menu Display
8 - (5-5) OSD Display
8 - (5-6) System Provider Mode
8 (6) Power Management
8 (7) DTV Programme Update
9 (8) Power On Default
9 - (8-1) Input Source
9 - (8-2) Programme
9 - (8-3) A/V Setting
9 - (8-4) Aspect Ratio
10 (9) Aux Source Setting
10 (10) Radio Name Display
10 (11) Radio Video Blank
10 - (11-1) Start PR. No.
10 - (11-2) No. of. PR.
11 (12) Factory Reset
13 TV MANAGER
13 - 1. USB
17 - 2. Diagnostics
19 NETWORK
20 PRO:CENTRIC
22 GENERAL
22 Password Change
22 Set ID Setup
23 Configuration Setup
26 Time Scheduler
26 Lock Mode
27 External Speaker
28 Speaker Output Setup
28 - Method of Volume control port
29 HCEC Setup
30 Power Saving
31 Clock Setup
33 Insert Image
34 Welcome Video
35 Crestron
36 CUSTOMIZABLE PORTAL
36 Portal Settings
39 Customizable Portal
40 AUDIO PROGRAMME
41 KEY CODES
42 EXTERNAL CONTROL DEVICE
SETUP
42 RS-232C Setup
42 USB to Serial converter with USB Cable
42 RS-232C with RS-232C Cable
43 - Connector type : D-Sub 9-pin male
43 - RS-232C configurations
43 Set ID
44 Communication Parameters
44 IR OUT Using Guide
44 - Suitable / Not Recommend remote-
controller data format
44 - IR Receiver specifications
45 Command reference list
46 TRANSMISSION / RECEIVING
PROTOCOL
2
INSTALLATION MENU
Introduction
The abundant functions for Hotel TV linked with software installation can be projected on OSD as
installation menu.
The wide range of hotel features can be performed simply on additional window to enhance the LG
hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.
* Image shown may differ from your TV.
1 Press the / (Settings) button for more than 5 seconds using the user remote
control, Programme information will appear at top left on the screen.
2 Enter a four digit password and press OK button. The TV is set with the initial password “1-1-0-5”.
3 Use the button to select the desired menu.
ENGLISH
3
LG Hotel Mode Setup
ENGLISH
* Image shown may differ from your TV.
1 Select LG Hotel Mode Setup.
• When LG Hotel Mode Setup is set to On(Work), all functions of Hotel Mode apply.
(1) Hotel Mode Operation (DVB)
• LG Hotel Mode Setup (DVB) Decide to work all functions of LG Hotel Mode Setup or not by
setting LG Hotel Mode Setup as On(Work) or Off(Do Not Work)
• When LG Hotel Mode Setup is set to On(Work), all functions of Hotel Mode apply.
• When LG Hotel Mode Setup is set to Off(Do Not Work), all functions of Hotel Mode Do Not apply.
• When it is set to On, ‘Key Lock’ item of the Safety menu is disabled and the OSD is displayed same
to the Local Key Operation setting of the Hotel mode.
• When it is set to On, all items reserved at the Schedule list are deleted and the reservation
function is not supported. (applied for the model offering the reservation function)
• The TV triggered by the external device (ex: SIMPLINK, TVLink-Tuner, etc.) operates separately
from the Hotel mode.
• When it is set to On, User Menu-> General-> Reset to Initial Settings is disabled.
• When it is set to On, User Menu-> General-> Demo Mode is disabled
(2) Power On Status
• Decide to select working status of TV Set when turn on main power.
• You can set with PWR, STD, LST.
• PWR always make TV set On status when turn on main power .
• STD make Stand-by status when turn on main power.
• LST make TVSet work like previous power status. As same concept as Power Backup mode; If main
power were turned off in Power On status, TVSet would work in On status. If main power were
turned off in Stand-by status, TVSet would work in Stand-by status.
4
(3) Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)
• Decide to apply volume policy of Start Volume, Maximum Volume and Minimum Volume
as On (Work) or Off (Do Not Work).
(3-1) Start Volume
This entry sets the start volume level when is power on.
• The level is specified as a number between minimum volume to maximum value.
(Min ≤ Start ≤ Max)
• The default setting is Off (disabled).
• When enabled, if the value is lower then the minimum specified in the minimum
volume entry, the minimum volume entry must be used.
• When enabled, if the value is larger then the maximum specified in the maximum
volume entry, the maximum volume value must be used.
• Access to a volume in Timer Power On must be fixed to start volume when LG Hotel
Mode Setup (On) and Start Volume (Off, 0 ~ 100) were set simultaneously.
(3-2) Maximum Volume
This entry sets the Maximum Volume level the set.
• The level is specified as a number between Minimum Volume to 100. (Min ≤ Max ≤ 100)
• If the command volume up to higher than maximum volume is received, that should be
ignored.
• The default value is 100.
(3-3) Minimum Volume
This entry sets the Minimum Volume level the set will produce.
• The level is specified as a number between 0 to Maximum Volume. (0 ≤ Min ≤ Max)
• If the command volume down to lower than minimum volume is received, that should
be ignored.
• The default value is 0.
ENGLISH
5
ENGLISH
(4) Key Operation
• Manage key usability of Local(Front) Key and Remote Control. When selected to On, following IR
Operation and Local Key Operation will be worked by below.
(4-1) IR Operation
Decide whether work the LG remote control or not.
• Able to set Normal, Use PWR Only, Block All
• When IR Operation is set to Block All, all normal remote keys don’t work. Use PWR
Only (Block except power) makes block all remote keys except power key.
• Although IR Operation value is Use PWR Only or Block All. It can work in service mode.
(In-Start, In-Stop, Power-Only, ADJ, Hotel-Mode, Hotel-Mode-Ready, P-Check, S-check,
In-Time, FMode-Init, FMode-Start, FMode-AV, FMode-F1)
• Menu key action to enter the installation menu and key action with special menu(In-
Start / EZ-Adjust …) are still available.
• When IR Operation is set to Normal (Work), all remote keys are available.
(4-2) Local Key Operation
Decide to operate Local/Front Key working behavior by setting Local Key Operation as
Normal, Use PWR Only, Block All
• When Local Key Operation is set to Block All, all local keys don’t work. (If value is Use
PWR Only, it blocks all local keys except power key.)
• When Local Key Operation is set to Normal, all local key are available.
Exception)
In case of power off condition with all key are blocked, Power On Status value turns to
PWR, and disabled status to fix value for power on operation. (fool-proof routine)
6
(5) Limited Mode
• Configure TV function’s limitation. When selected to On, following sub-menus will be worked by
below.
(5-1) Setup Menu
Decide to enter Setup Menu or Programmes Menu as On (Enter possible) or Off (Enter
impossible)
(5-2) Input Source Change
Decide to change input source or not by setting Input Source Change as On (Change
possible) or Off (Change impossible).
• When Input Source Change is set to Off (Change impossible)
- Input key doesn’t work, and Input Source Changing via TV D/A key, TV/RADIO key
aren’t possible (ex. Press TV/RADIO Key in HDMI source to view TV Programme)
- User’s input (pressing Programme key, numeral key, List key, Flash back key in all Input
source except TV source) doesn’t work.
- Entering Programmes of User Menu item in the main menu OSD except TV mode
doesn’t accepted. Because entering Programmes of User Menu item makes present
mode as TV mode even though present mode is not TV. Change to TV mode isn’t
allowed.
- Entering Programmes of User Menu except TV mode is impossible regardless of
Programme Change or Programmes of User Menu items’ value.
- TV can be only turned on with the input source which is irrelevant from the programme
related information set (volume, input) in Timer Power On of User Menu.
- Auto AV and HDMI-CEC still work regardless of Input Source Change’s value.
• When Input Source Change is set to On (Change possible), changing input source is
available.
ENGLISH
(5-3) Programme Change
Decide to change Programme or not by setting Programme Change as On (Change
Possible) or Off(Change Impossible) when present source is TV.
• When Programme Change is set to Off (Change Impossible)
- Program Key, Numeral Key, List Key, Q.View Key don’t work and entering Programmes
Menu in the Main Menu OSD is impossible.
- Programme item in Timer Power On menu will be fixed.
- Entering Setup Menu or Programmes Menu in the Main Menu OSD is impossible
regardless of Setup Menu or Programmes Menu item
• When Program Change is set to On (Change Possible), Programme Key, Numeric Key,
List Key, Q.View Key does work and entering Programmes Menu in the Main Menu
OSD is possible.
(5-4) Menu Display
Function to decide whether work with menu (including relevant menus too) of control
key (On – Enter possible) or not (Off – Enter Impossible).
• Although select Off (Enter impossible), the action that press a Menu button for 5
seconds to enter installation menu is available.
• When select On (Enter possible), Menu works.
7
ENGLISH
(5-5) OSD Display
Decide to display OSD or not by setting OSD Display as On (Display) or Off (Do not
Display).
• When OSD Display is set to Off (Do not Display), all OSD is not displayed except some
exception.
• Although select Off (Do not Display), the action that press a (SETTINGS) for 5 seconds
to enter installation menu and entering service menu are available. (In-Start, PowerOnly, Adjust, Installation Menu …)
(5-6) System Provider Mode
System Provider Mode allows access to the menu system from the front panel or remote
control but access is controlled as follows:
• When value is On, Accessible Items on the menu system, others are not permissible.
- Input select screens
- Sleep Timer
- Alarm (Only for LU5**H series)
- Aspect Ratio
- Subtitles
- Lock System, Set Password
- My Media / Network Menu
- Support Menu(* LU30* C series use ‘About This TV’)
• Q.menu, which is related to Setup Menu or Programmes Menu, is not accessible.
• If the Programme map is empty, Auto-tuning guide dialog should be blocked by
pressing List, Fav, CH+ (Page up), CH- (Page down) keys.
(6) Power Management
The Power Management feature will turn off the television receiver if no input control command is
received from either the Local or IR Key within a selected hours.
• Activity on either of these inputs shall restart the Power Management timer and prevent
interruption of TV viewing.
• This entry can be set to a value which is corresponding to the desired hours (1 to 7).
• Default value is Off (disabled).
• TV should off and on after apply this setting.
(7) DTV Programme Update
It is a mode to set whether to update DTV Programme information automatically or not.
• When DTV Programme Update is set to Auto, the function to update TV’s Programme map
according to DTV Programme’s stream information
• DTV Programme Update is set to Manual, the function to keep TV’s Programme map even
though DTV Programme’s information is changed.
• For LU5**H series, this function is available in CONFIGURATION SETUP
8
(8) Power On Default
Set the input source or Programme to display and. A/V settings when turn on power in AC Power On
or Stand-by status.
(8-1) Input Source
Set whether it is turned on by the set input source or by the last stored input source.
• It is turned on by the Last Memory Input if the Input Source is turned off.
• It is turned on by the Last Pr. If the Input Source is turned off and the last memory
Input is the RF.
• The available Input Source values should be rotated.
• If both the Input Source and the Timer Power On of User Menu are set, the Input
source takes the priority.
• When the Input Source is changed to the TV, Programmes menu is available.
• When the Input Source is changed to the ATV, the Programme No. is set to 0. (If the
Programme map structure does not support this, it depends on model’s Programme
handling.)
• Access to an input source item and a Programme in Timer Power On of User Menu
must be disabled when Power On Default is activated.
(8-2) Programme
Select start Programme number if Input source’s value is TV. (in case of ATV, it means
physical Programme number.)
(8-3) A/V Setting
If A/V Setting is changed from Off to On, parameters that are set before entering
installation menu are applied whenever turn on power.
• Following Parameters are applied to basic.
- Picture section - PSM mode, Picture Data (Contrast, Brightness, Color, Sharpness, Tint)
- Sound section - SSM mode, Sound Data (Balance, Equalizer Data)
- AVL (Auto Volume Level) and Language, Teletext language, ARC Data.
• Except these, other parameters are applied differently according to the TV-Set.
ENGLISH
(8-4) Aspect Ratio
The aspect ratio determines the default aspect ratio that the set returns to on power up.
• The modes are as follows:
- Aspect ratio = “Disable (0)” stays at previous state, same as consumer model.
- Aspect ratio = “Original (1)”
- Aspect ratio = “4:3 ratio (2)”
- Aspect ratio = “16:9 ratio (3)”
• If enabled, upon power up the television resets the aspect ratio to the specified state
regardless of how the user has previously changed the aspect ratio.
• If Original is not supported, the television set the aspect ratio to 16:9.
9
ENGLISH
(9) Aux Source Setting
The Auxiliary (Input) Source Setting feature will enable or disable for each external input. When Aux
Source Setting is set to On (Work), the RJP or HDMI-CEC / HTNG will not operate.
• Available Input Source List
• Decide whether selected Input Source is set to On (Enable) or not (Disable).
• User cannot disable the current input’s Aux Source Setting.
(10) Radio Name Display
Instead of ‘Audio Only’, the name of a radio Programme is displayed on the screen when a radio
broadcast is playing. Set to On (Work) or Off (Do Not Work).
If the setting is On, the name of a radio Programme is displayed for the radio Programme.
• Set to On (Work) or Off (Do Not Work).
• If the setting is On, the name of a radio Programme is displayed for the radio Programme.
• For LU5**H series, this function is available in CONFIGURATION SETUP.
(11) Radio Video Blank
Manage video blank Programme(sound only). This feature affects on analog Programme (ATV) only.
(11-1) Start PR. No.
• Start Programme number to video blank.
• Available programme to set are 0~199 (For Taiwan : TV 2~69, CATV 1~199).
(11-2) No. of. PR.
• Number of Programmes to blank
• The max value for the ‘No. of PR’ is 10.
• Can not set more than maximum available Programme number. For example if Start PR.
set to 195, “Number of PR”. can not set more than 5.
• Radio programme should be in sequence with starting programme number.
10
(12) Factory Reset
Factory reset returns all the parameters to the default settings.
1 Press Enter key to proceed factory reset. and confirmation message window will be shown.
2 When select On, all television settings except UTT value should write to the default settings.
ENGLISH
11
Public Display Settings / LG Hotel Mode Setup (Value Range Table)
ENGLISH
Item Enable Disable Initial
LG Hotel Mode Setup On Off Off
Power On Status LST, STD, PWR STD
Volume
Start Volume Off, Minimum Volume ~ Maximum Volume Off
Maximum Volume
Minimum Volume 0 ~ Maximum Volume 0
Key Operation On Off Off
IR Operation Normal / Use PWR Only / Block All Normal
Local Key Operation Normal / Use PWR Only / Block All Normal
Limited Mode On Off Off
Setup Menu
Input Source Change On Off On
Programme Change On Off On
Menu Display
OSD Display
System Provider Mode On Off Off
Power Management Off, 1 Hour ~ 7 Hours Off
DTV Programme Update Auto Manual Auto
Power On Default On Off Off
Input Source
Programme
A/V Setting
Aspect Ratio
Aux Source Setting
Aux Input
(AV1 ~ MAX_INPUT)
Radio Name Display
Radio Video Blank
Start PR. No.
No. Of. PR. 0 ~ 10
(Start PR. NO + No. of PR. <= Max Start PR. NO. + 1)
Factory Reset
On Off Off
Minimum Volume ~ 100 100
On Off On
On Off On
On Off On
Off, AT V, DTV, ... Off
Minimum Program ~ Maximum Program
On Off Off
Disable / Original / 4:3 / 16:9 Disable
On Off Off
On Off On
On Off Off
On Off Off
0 ~ 199 ( Taiwan T V 2 ~ 69 / CATV 1 ~ 199) 1
Confirmation window (On / Off)
Minimum
Program
1
12
TV Manager
1. USB
Ez Download
Ez Download is a function that enables users to download the desired items all at once, such as EPK
(software update file), TLL (See Send to USB descriptions for more information regarding file types),
Logo Image, etc (TLX, MICOM for Pro:Centric).
• Splash images and EPK files should be copied into the folder named LG_DTV on the USB.
TLL files should be copied to the root folder of the USB.
• Insert Image files shoud be copied into the folder named LG_SIG on the USB.
* Image shown may differ from your TV.
1 Plug USB memory card into the USB port of the TV.
2 Use the button to select the TV Manager option and then press the OK button.
3 Use the button to select the USB and Ez Download and press the OK button.
4 Select a list to download and press the OK button.
5 Select the EPK option (software update) and then use the two dots and three dots buttons
to download either SPI Boot or LG Boot Logo. If you checked the LG Boot Logo checkbox,
then the Splash image, if selected, will be unchecked. Also, if you select the LG Boot Logo and
proceed with the download, the existing Splash image will be deleted.
6 When you are finished with your selections, use the button to select Apply and then press
OK.
7 Wait for the download to complete. When it is finished, your TV will be turned off.
NOTE
• If the DZM file is still in the USB after the download is complete:
An Ez Download pop-up window will appear and list the file types, such as TLL, Logo Image,
Background Images, EPK or Micom with the previously downloaded lists checked automatically.
• If the global TLL and model TLL files exist in the same USB root directory, then only the global TLL
will be shown. If the global TLL has been deleted, then the model TLL will be shown.
ENGLISH
13
USB Cloning
ENGLISH
An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will
all have the same Master TV Setup: Public Display Settings, Installation menu settings, User A/V
settings and the Programme Map. This newer procedure significantly decreases the installation time
that would be necessary if the standard RS-232C method were used instead.
Introduction
(1) Overview USB Cloning Procedure
• Commercial TVs have the capability to support cloning internal TV data and Programme
information with an external clone device called USB Cloning, in order to copy TV data accurately
and quickly. The clone internal functions use slightly different internal processes for the two
types of commercial TVs. However, the UI of cloning feature remains the same in both. Regarding
the demands over the current cloning feature for quicker cloning, better portability and etc, we
would like to announce the cloning process via USB port, named as USB Cloning. USB cloning
process is divided into 2 main processes. One is writing the previously saved TV data into the TV,
and one another is reading of current TV data into USB memory card. To avoid any confusion due
to the words, it is clearly specified as Receive from USB and Send to USB in the whole process.
(2) Data To Be Cloned
• The data cloned are the same data cloned by previous USB Cloning. Details are explained in the
following:
- 1. TV data includes:
A. Installer Menu settings
B. Main menu settings (Audio, Picture etc)
- 2. Analog / Digital Programme information includes:
A. Programme numbers
B. Programme label
C. Programme attributes including Programme type, skipping status and etc.
(3) Input Source
The user needs a USB memory card with FAT formatted to make successive cloning via USB port. A
USB memory card size more than 128 MB and less than 4 GB is recommended.
NOTE
• Currently, support the preceding USB file system for FAT file format only. Other file formats
including NTFS is not currently supported. Microsoft Windows officially supports FAT for the USB
memory card.
14
Receive From USB
* Image shown may differ from your TV.
1 Plug USB memory card into the USB port of the TV.
2 Use the button to select the TV Manager option and then press the OK button.
3 Use the button to select the USB and Receive from USB and press the OK button.
* Below explains the naming rules for .TLL files. The supported model line will be in the name of
the file but the screen size will be listed as “xx”. This allows TVs having the same chassis model
number to use the same ‘*.TLL’ file without regard to the screen size. ex) The name of ‘*.TLL’ file is
‘xxLU340L-UA00000.TLL’ for 32/43LU340L-UA model.
4 Use the button to select the desired *.TLL files name and press the OK button.
5 The TV is changed to Standby mode after a successful download. If the download failed, the
TV will maintain the current screen.
Send To USB
* Image shown may differ from your TV.
ENGLISH
1 Plug USB memory card into the USB port of the TV.
2 Use the button to select the TV Manager option and then press the OK button.
3 Use the button to select the USB and Send to USB and press the OK button.
4 Use the button to select the desired file name and press the OK button.
5 The TV will be changed to the TV Manager main screen after a successful download.
15
Logo Image Download
PCMCIA CARD SLOT
ENGLISH
Make a ‘LG_DTV’ folder on the USB flash drive and then copy the splash image file to that folder.
* Image shown may differ from your TV.
1 Connect the USB device to the USB IN jack on the TV.
2 Use the button to select the TV Manager option and then press the OK button.
3 Use the button to select the USB and Logo Image Download and press the OK button.
4 Use the button to select the desired file name and press the OK button.
NOTE
• Splash Image update function supports only JPEG format file of less than 1 MB file size.
• Except for JPEG images with progressive encoding.
• We recommend you that splash image resolution match the TV`s panel resolution.
• Max resolution of splash image : Full HD -> 1920 x 1080, HD -> 1360 x 768.
• Min resolution of splash image : Full HD -> 64 x 64, HD -> 64 x 64.
• TV keep splash image until you change a new splash image.
• Please do not use the ampersand character(&) and the left angle bracket (<) in the file name to
use DZM file on EZ Download.
• Non-standard photo/image file may not be displayed.
16
Loading...