LG 42SL90UA Users manual

Order Number : GETEC-C1-09-170 FCC Class B Certification Test Report Number : GETEC-E3-09-089 Page 1 / 1
: USER’S MANUAL
EUT Type: LCD TV/ Monitor
FCC ID.: BEJ42SL90UA
Please read this manual carefully before operating your set and retain it for future reference.
The model and serial number of the TV is located on the back and one side of the TV.
Record it below should you ever need service.
LED LCD TV OWNER’S MANUAL
42LH90 47LH90 55LH90
P/NO : SAC33601910 (0907-REV00)
www.lgusa.com / www.lg.ca
This product qualifies for ENERGY STAR in the “factory default (Home Use)” setting.
Changing the factory default settings or enabling other fea­tures may increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR.
Model:
Serial:
1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA
LG Customer Information Center
42SL80 47SL80 55SL80
42SL90 47SL90
LCD TV OWNER’S MANUAL
2
WARNING / CAUTION
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two condi­tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device).
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product
3
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com­bination to avoid injury from tip-over.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1
2
3
4
5
7
8
6
9
10
4
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed
upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GGRROOUUNNDDIINN GG Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out­let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS Mains plug is the disconnecting device. The
plug must remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
12
11
14
13
16
17
18
19
Power Supply
Short-circuit
Breaker
15
5
AANN TTEENNNNAASS OOuu ttddoooorr aann tteennnn aa ggrroouunn ddiinngg If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system should not be located in the vicinity of over­head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding electrode.
AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700
CC lleeaanniinngg When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
MMoovv iinn gg Make sure the product is turned off,
unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
VVeenn ttii llaattiioo nn Install your TV where there is proper ventila-
tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Keep the product away from direct sunlight.
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary dis­tortion effects on the screen.
20
23
24
25
26
27
21
22
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC: National Electrical Code
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
PREPARATION
9
ACCESSORIES
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
Owner’s Manual
Power Cord
CD Manual
OOppttiioonn EExxttrraass
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly. Excessive pres-
sure may cause scratches or discol­oration.
Polishing Cloth
Not included with all models
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.
OOnnllyy 4422//4477//5555LLHH9900
1.5V 1.5V
Remote Control, Batteries
FA
V
M
U
T E
Q .
M E
NU
M E
NU
A
V MO
D
E
RETURN
VOL
C
H
123
456
78
0
9
FLASHBK
P A
G
E
INPUT
INFO
LIST
ENT
E R
POWER
TV
ENERGY SA
V ING
ON/OFF
MARK
Protection Cover
Screws for stand assembly
(Refer to P.14)
Screw for stand fixing
(Refer to P.21)
x 4
(For 42/47LH90)
(For 42LH90)
OOnnllyy 4422//4477SSLL9900
Bolts for stand assembly
(Refer to P.16)
Cable Management Clip
(Refer to P.19)
Cable Holder
(Refer to
P.19)
x 1
OOnnllyy 4422//4477//5555SSLL8800
Bolts for stand assembly
(Refer to P.15)
Cable Management Clip
(Refer to P.18)
Protection Cover
(Refer to P.15)
x 8
(Except 55SL80)
Cable Holder
(Refer to
P.18)
Simple Remote Control,
Batteries
1.5V 1.5V
CH
V O
L
F L A S
H B A C
K
T
V / I N
P U T
x 3
x 4
P O
W E
R
A
V
M
O D
E
E N E R
G Y
S A V
I N G
P
A G E
C
HVO
L
F
A V
M A
R
K /
M
U T
E
O N /
O F F
123
45
0
6
789
L I
S T
F L A
S H
B A
C K
I N
P U
T
M
E N
U
R
A T
I O
Q.MENU
R E
T U R
N
I
N F
O
E
N T
E
R
T
V
or
PREPARATION
10
FRONT PANEL INFORMATION
PREPARATION
Image shown may differ from your TV.
CHANNEL ( , ) Buttons
VOLUME (+, -) Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
AC power control switch
SPEAKER
Power/Standby Indicator
Illuminates red in standby mode. Illuminates white when the TV is switched on. (Can be adjusted using the
PP ooww ee rr IInnddiiccaattoorr
in the
OPTION menu.
GG
pp ..88 44
)
Remote Control Sensor, Intelligent Sensor
Adjusts picture according to the surrounding conditions
42/47/55LH90
42/47/55SL80
Main power switch (For 42/47/55SL80)
OFF ON
Remote Control Sensor
INPUT Button
POWER Button
MENU Button
ENTER Button
CHANNEL ( , ) Buttons
VOLUME (-, +)
Buttons
Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the TV is switched on (Can be adjusted
using the
PPoo wweerr IInnddiiccaa tt oo rr
in the OPTION menu.
GG
pp .. 8844
).
Intelligent Sensor
Adjusts picture according to the surrounding con­ditions
GG
Do not step on the glass stand or subject it to any impact.It may break, causing possible injury from fragments of glass, or the TV may fall.
GG
Do not drag the TV. The floor or the product may be damaged.
NOTE
!
CH
VOL
ENTER
MENU
INPUT
CH
VOL
ENTER
MENU
INPUT
PREPARATION
11
Image shown may differ from your TV.
42/47SL90
Main power switch (For 42/47SL90)
OFF ON
Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the TV is switched on (Can be
adjusted using the
PPoo wweerr IInnddiiccaa tt oo rr
in the OPTION
menu.
GG
pp .. 8844
).
GG
Do not step on the glass stand or subject it to any impact.It may break, causing possible injury from fragments of glass, or the TV may fall.
GG
Do not drag the TV. The floor or the product may be damaged.
NOTE
!
CHANNEL ( , ) Buttons
VOLUME (+, -) Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
Sensor de Control Remoto
Sensor Inteligente
Ajusta la imagen según las condi­ciones del entorno.
CH
VOL
ENTER
MENU
INPUT
PREPARATION
12
PREPARATION
BACK PANEL INFORMATION
Image shown may differ from your TV.
( )
( )
R
1 2
6 57
9
1
8
2
4
3
42/47/55LH90
VIDEO
AUDIO
L R
(
CONTROL&SERVICE)
RS-232C IN
AUDIO IN
(RGB/DVI)
DIGITAL AUDIO OUT
OPTICAL
ANTENNA/
CABLE IN
RGB IN (PC)
COMPONENT IN
2
3
1
1
2
MONO
( )
AUDIOVIDEO
/DVI IN
LR
R
AV IN 1
R
2 4 3 6
5
1
7
42/47/55SL80
9
R
6
8
2
2
1
AV IN 1
( )
MONO
LR
VIDEO
COMPONENT IN
AUDIOVIDEO
3
2
L R
1
AUDIO
/DVI IN
RGB IN (PC)
AUDIO IN
(RGB/DVI)
RS-232C IN
(
CONTROL&SERVICE)
OPTICAL DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
USB IN
IN 4
R
AUDIO
L/ MONO
VIDEO
AV IN 2
USB IN
IN 4
R
AUDIO
L/ MONO
VIDEO
AV IN 2
PREPARATION
13
42/47SL90
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
HDMI/DVI IN, HDMI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t
support 480i. Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
AUDIO IN (RGB/DVI)
1/8" (0.32 cm) headphone jack for analog PC audio input.
OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps and home theater systems.
Note: In standby mode, this port doesn’t work.
ANTENNA/CABLE IN
Connect over-the air signals to this jack. Connect cable signals to this jack.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices. This port is used for Service or Hotel mode.
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red
and white for audio.
USB IN
Used for viewing photos/movies and listening to MP3s.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
1
2
3
4
8
9
7
6
5
VIDEO
AUDIO
L R
(
CONTROL&SERVICE)
RS-232C IN
AUDIO IN
(RGB/DVI)
DIGITAL AUDIO OUT
OPTICAL
ANTENNA/
CABLE IN
RGB IN (PC)
COMPONENT IN
2
3
1
1
2
MONO
( )
AUDIOVIDEO
/DVI IN
LR
AV IN
R
USB IN
IN 4
8
2
2 4 3 6
5
1
7
9
PREPARATION
23
ANTENNA OR CABLE CONNECTION
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Image shown may differ from your TV.
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wall Antenna Socket
Outdoor Antenna (VHF, UHF)
Cable TV Wall Jack
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
Copper Wire
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
R
R
EXTERNAL EQUIPMENT SETUP
24
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
1. How to connect
Connect the video outputs (Y, P
B, PR
)
of the digital set-
top box to the
CC OO MMPP OO NNEENNTT II NN VV II DDEEOO 11
or
22
jacks on the TV. Match the jack colors (Y = green, P
B =
blue, and P
R = red).
Connect the audio output of the digital set-top box to the
CCOOMMPPOO NNEENNTT IINN AAUUDDIIOO 11
or
22
jacks on the TV.
2
1
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box operation.
)
Select the
CC oommpp oonn ee nntt11
or
22
input source on the TV
using the
IINNPP UUTT
button on the remote control.
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
This part of EXTERNAL EQUIPMENT SETUP mainly use picture for
4422//4477 //5555LL HH 9900
.
Y, CB/PB, CR/PR
Supported Resolutions
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
15.73 59.94
15.73 60.00
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480i
720x480p
1280x720p
1920x1080i
1920x1080p
Signal
480i
480p
720p
10 8 0 i
10 8 0 p
Component
Yes
Yes
Yes
Yes
Yes
HDMI
No
Yes
Yes
Yes
Yes
AV IN 1
2
3
1
MONO
( )
AUDIOVIDEO L R
/DVI IN
VIDEO
AUDIO
L R
COMPONENT IN
2
1
Y L RPB PR
1
2
EXTERNAL EQUIPMENT SETUP
25
HDMI Connection
Connect the digital set-top box to
HHDDMM II //DDVVII II NN 11
,
22, 33
, or
44
jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HHDDMMII11, HHDDMMII22, HHDDMMII33
, or
HHDDMMII44
input
source on the TV using the
IINNPPUUTT
button on the remote
control.
2
1
HDMI-DTV
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67. 432 59 .94
67.50 60.00
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
( )
AUDIO
L R
RS-232C IN
(
CONTROL&SERVICE)
AUDIO IN
(RGB/DVI)
O
A
C
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOVIDEO L R
2
3
1
/DVI IN
HDMI OUTPUT
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
GG
HDMI mode supports PCM, Dolby Digital audio format.
NOTE
!
EXTERNAL EQUIPMENT SETUP
26
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
( )
( )
AUDIO
L R
RS-232C IN
(
CONTROL&SERVICE)
OPTICAL DIG
AUDIO OU
ANTENNA
CABLE IN
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOLR
2
3
1
/DVI IN
AUDIO IN
(RGB/DVI)
L R
DVI OUTPUT
AUDIO
1
2
GG
A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio connection is necessary.
NOTE
!
Connect the DVI output of the digital set-top box to the
HHDDMMII //DDVVII IINN 11, 22
, or 33jack on the TV.
Connect the digital set-top box audio output to the AAUUDDIIOO II NN ((RRGGBB// DD VV II
))
jack on the TV.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HHDDMMII11, HHDDMMII22
, or
HHDDMMII33
input source on the
TV using the
IINNPPUUTT
button on the remote control.
2
1
EXTERNAL EQUIPMENT SETUP
28
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
VIDEO
AUDIO
L R
COMPONENT IN
2
3
1
2
1
/DVI IN
( )
AV IN 1
MONO
( )
AUDIOVIDEO LR
L R
VIDEO
AUDIO
HDMI Connection
( )
AUDIO
L R
RS-232C IN
(
CONTROL&SERVICE)
AUDIO IN
(RGB/DVI)
OPT
A
AN
C
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOVIDEO L R
2
3
1
/DVI IN
HDMI OUTPUT
( )
1
Connect the
AAUUDDII OO/VVIIDDEEOO
jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select the
AAVV11
or
AAVV22
input source on the TV using the
IINNPP UUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
1
Connect the HDMI output of the DVD to the HHDDMMII //DDVVII IINN 11, 22, 33
or 44jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Select the
HHDDMMII11, HHDDMMII22, HHDDMMII33
, or
HHDDMMII44
input
source on the TV using the
IINNPP UUTT
button on the remote
control.
Refer to the DVD player's manual for operating instructions.
2
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
1
EXTERNAL EQUIPMENT SETUP
30
PC SETUP
EXTERNAL EQUIPMENT SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
RS-232C IN
(
CONTROL&SERVICE)
OPTICAL DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
2
3
1
R
/DVI IN
AUDIO IN
(RGB/DVI)
RGB IN (PC)
RGB OUTPUT
AUDIO
2
1
Connect the VGA output of the PC to the
RRGGBB IINN
((
PP CC
))
jack on the TV.
Connect the PC audio output to the
AAUUDDIIOO IINN
((
RRGGBB//DDVVII
))
jack on the TV.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select the
RRGGBB--PP CC
input source on the TV using the
IINNPP UUTT
button on the remote control.
2
1
DVI to HDMI Connection
( )
AUDIO
L R
RS-232C IN
(
CONTROL&SERVICE)
OP
A
A
C
RGB IN (PC)
AV IN 1
MONO
( )
AUDIOVIDEO L R
AUDIO IN
(RGB/DVI)
2
3
1
/DVI IN
AUDIO
DVI OUTPUT
1
2
Connect the DVI output of the PC to the
HHDDMM II//DDVVII
IINN 11, 22
, or 33jack on the TV.
Connect the PC audio output to the
AAUUDDIIOO IINN
(( RR GG BB //DDVVII))
jack on the TV.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select the
HHDDMMII11, HHDDMMII22
, or
HHDDMMII33
input source on
the TV using the
IINNPP UUTT
button on the remote control.
2
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
EXTERNAL EQUIPMENT SETUP
31
NOTES
!
Supported Display Specifications (RGB-PC, HDMI-PC)
Resolution
720x400
640x350
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.468 70.09
31.469 70.08
31.469 59.94
37.879 60.31
48.363 60.00
47.776 59.87
47.712 60.015
63.981 60.02
75.00 60.00
66.587 59.934
67.50 60.00
640x480
800x600
1024x768
1280x768
1280x1024
1360x768
1600x1200
1920x1080
RGB-PC
1920x1080
HDMI-PC
GG
To get the best picture quality, adjust the PC graph­ics card to 1920x1080.
GG
Depending on the graphics card, DOS mode may not work if an HDMI to DVI Cable is in use.
GG
In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or bright­ness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
GG
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become permanently imprinted on the screen.
GG
Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.
GG
If the screen is truncated using HDMI-PC 1920x1080, try changing the aspect ratio to
JJuusstt
sscc aann
.
GG
When selecting HDMI-PC, set the “Input Label ­PC” in the OPTION menu.
EXTERNAL EQUIPMENT SETUP
32
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
You can choose the resolution in RGB-PC mode. The
PPoossiitt ii oonn, PPhhaa ss ee
, and
SSii zz ee
can also be adjusted.
Select
PP II CCTTUURR EE
.
Select
SS ccrreeeenn ((RRGG BB --PPCC ))
.
Select
RReessoo lluuttiioonn
.
Select the desired resolution.
1024 x 768
1280 x 768
1360 x 768
Auto Config.
Resolution
Position
Size
Phase
Reset
SCREEN
Move
Prev.
1
MENU
3
4
2
ENTER
ENTER
ENTER
5
ENTER
Enter
Move
PICTURE
E
RG
• Brightness 50
• Sharpness 50
• Color 50
• Tint 0
• Advanced Control
• Picture Reset
Screen (RGB-PC)
LED Local Dimming :On
Loading...
+ 44 hidden pages