LG 42PX3D User Manual

Installation and Operating Guide | Warranty

Model Numbers | Z42PX3D/Z50PX3D | PLASMA TV

As an ENERGY STAR Partner LGE U.S.A., Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

EENNEERRGGYY SSTTAARR iiss aa ss eett ooff ppoowweerr-- ss aavvii nngg gguuiiddee ll iinnee ss iissssuu ee dd bbyy tt hh ee UU..SS.. EEnnvv iirroonnmmee nntt aall PPrroo tt ee cc ttiioo nn AAgg ee nncc yy ((EEPPAA ))..

Warning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this device compliance is: Zenith Electronics Corporation 1-201-816-2000 Marked and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

arning

Safety Instructions

WARNING :

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use the attachments / accessories specified by

the manufacturer.

Safety Instructions

Owner's Manual

Safety Instructions

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. DISCONNECTING DEVICE FROM MAINS

Main plug is the disconnecting device.The

plug must remain redily operable.

On Disposal

a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

Note

- If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on. This is normal, there is nothing wrong with TV.

- Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

- Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Contents

Introduction

Installation

Operation

27 Turning on the TV 27 Volume Adjustment 27 Channel Selection 27 On Screen Menus Language Selection 28 On Screen Menus Selection and Adjustment

29 EZ Scan (Channel Search) 29 Manual Scan 30 Channel Edit 31 DTV Signal Strength 31 Input Source 32 Input Label

33 Auto Picture Control(EZ Picture) 33~34 Color Temperature Control 35 DB 36 Advanced-Cinema 3:2 Mode / Black Level 37 Video Reset

38 Audio Language 39 Auto Sound Control(EZ Sound) 39~40 Manual Sound Control (EZ Sound-User option) 41 Balance 41 TV Speakers On/Off Setup

2 Warnings

3~4 Safety Instructions

7 Accessories

8 Controls (Model Name: Z42/50PX3D)

9 Connection Options (Model Name: Z42/50PX3D)

10 Controls (Model Name: Z42LC2DA)

11 Connection Options (Model Name: Z42LC2DA)

12~13 Remote Control Key Functions

14 Attaching the TV to a wall 15 Desktop Pedestal Installation

16 Antenna or Cable Connection 17~18 VCR Setup 18 External AV Source Setup 19~20 DVD Setup 21~22 HDSTB Setup 23 AV Out Setup 23 Digital Audio Output 24~26 PC Setup

Setup Menu

Options

Video Menu

Options

Audio Menu

Options

Basic operation

External

Equipment

Connections

Contents

Reference

42 Manual Clock Setup 42 Auto Clock Setup 43 On/Off Timer Setup 43 Sleep Timer 44 Auto Off

45 Aspect Ratio Control 46 Caption/Text 47 Caption Option 47 Low Power (Z42/50PX3D only) 48 ISM (Image Sticking Minimization) Method

(Z42/50PX3D only)

49~50 Parental Lock Setup

51~56 External Control Device Setup

57~58 IR Codes

59 Programming the Remote

60~61 Programming Codes

62~63 Troubleshooting Checklist

64 Maintenance

65 Product Specifications

67~68 Warranty

Option Menu

Features

Lock Menu Options

Operation

Time Menu

Options

Introduction

Accessories

Introduction

Owner’s Manual

75Ω Round Cable

Power Cord

Ensure that the following accessories are included with your TV. If any accessory is missing, please contact the dealer from where you purchased the product. User must use shielded signal interface cables(D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

1.5V

ENTER

VOL

FL A SH

B ACK

MUTE

TIMER

SAP

123

ENTER

TVTV

INPUT

DVD

RATIO

EXIT

VOL

EZ SOUND

INFO

ADJUST

EZ PIC

FL ASH

B ACK

MUTE

TIMER

SAP

VCR

POWER

123

456

789

FAV

COMP1

MODE

COMP2

HDMI

RGB-PC

Remote Control /

Batteries

2-eye-bolts

2-TV brackets

2-Wall brackets

2-TV Bracket Bolts

For Z42LC2DAFor Z42/50PX3D

Twister Holder

Arrange the wires

with the twister holder.

Cable

Management

(Refer p.18)

Polishing Cloth

Polish the TV with the cloth.

Slightly wipe stained spot on the exterior only with the cleansing cloths for the product exterior if there is stain or fingerprint on surface of the exterior. Do not wipe roughly when removing stain. Please be cautious of that excessive power may cause scratch or discoloration.

2-Wall brackets

Option Extras

D-sub 15 pin cable

Introduction

Controls

Controls (Model Name: Z42/50PX3D)

- This is a simplified representation of front panel.

- This picture shown below may be somewhat different from your TV.

POWER Button

INPUT Button

ENTER Button

VOLUME (

FF , GG)Buttons

CHANNEL (

EE , DD)Buttons

Power Standby Indicator

Illuminates red in standby mode. Illuminates green when the set is switched on.

VOL

MENUINPUT ENTER

MENU Button

Introduction

Connection Options

(Model Name: Z42/50PX3D)

- This picture shown below may be somewhat different from your TV.

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1AV IN 1

AV OUTAV OUT

ANTENNA/

CABLE IN

REMOTE

(CONTROL & SERVICE)

COMPONENT INCOMPONENT IN

DIGITAL AUDIO DIGITAL AUDIO

OUTOUT

OPTICALPTICAL

SERVICE

HDMI / DVI IN

S-VIDEO Input

Provides better picture quality than the video input.

AUDIO Input

Connections are available for listening to stereo sound from an external device.

VIDEO Input

Connects the video signal from a video device.

COMPONENT IN

Connect a component video/audio device to these jacks.

AV OUT

Connect a second TV or monitor.

AV (Audio/Video) IN 1

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

DIGITAL AUDIO OUT

Connect digital audio from various types of equipment.

Note: In standby mode, these ports do not work.

HDMI/DVI IN

Connect a HDMI signal. Or DVI (VIDEO)signal to the this port with a

HDMI to DVI cable.

RGB IN (PC)

Connect the monitor output from a PC to the appropriate input port.

REMOTE CONTROL IN Port

Connect your wired remote control.

AUDIO IN (RGB/DVI)

Connect the monitor output from a PC to the appropriate input port.

RS-232C IN (CONTROL & SERVICE) Port

Connect to the RS-232C port on a PC.

SERVICE

Power Cord Socket

For operation with AC power. Caution: Never attempt to operate the TV on DC power.

Introduction

Controls

Controls (Model Name: Z42LC2DA)

- This is a simplified representation of front panel.

- This picture shown below may be somewhat different from your TV.

VOL

ENTER

INPUT

CHANNEL (D, E) Buttons

VOLUME (F,G) Buttons

ENTER Button

MENU Button

INPUT Button

Remote Control Sensor

Power/Standby Indicator

• illuminates red in standby mode.

• illuminates green when the set is switched on.

(Power) Button

Swivel Stand (Z42LC2DA

Only)

- The TV can be conveniently swivelled on its stand

° to

the left or right to provide the optimum viewing angle.

VOL

ENTER

INPUT

Introduction

Connection Options

(Model Name: Z42LC2DA)

- This picture shown below may be somewhat different from your TV.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

AC IN

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1AV IN 1

AV OUTAV OUT

ANTENNA/

CABLE IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

COMPONENT INCOMPONENT IN

DIGITAL AUDIO

OUT

PTICAL

SERVICE

HDMI / DVI IN

S-VIDEO Input

Provides better picture quality than the video input.

VIDEO Input

Connects the video signal from a video device.

AUDIO Input

Connections are available for listening to stereo sound from an external device.

COMPONENT IN

Connect a component video/audio device to these jacks.

AV OUT

Connect a second TV or monitor.

AV (Audio/Video) IN 1

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

DIGITAL AUDIO OUT

Connect digital audio from various types of equipment.

Note: In standby mode, these ports do not work.

HDMI/DVI IN

Connect a HDMI signal. Or DVI (VIDEO)signal to the this port with a

HDMI to DVI cable.

RGB IN (PC)

Connect the monitor output from a PC to the appropriate input port.

REMOTE CONTROL IN Port

Connect your wired remote control.

AUDIO IN (RGB/DVI)

Connect the monitor output from a PC to the appropriate input port.

RS-232C IN (CONTROL & SERVICE) Port

Connect to the RS-232C port on a PC.

SERVICE

Power Cord Socket

For operation with AC power. Caution: Never attempt to operate the TV on DC power.

Introduction

Remote Control Key Functions

ENTER

TVTV

INPUT

DVD

RATIO

EXIT

VOL

EZ SOUND

INFO

ADJUST

EZ PIC

FLASH BACK

MUTE

TIMER

SAP

VCR

POWER

123

456

789

FAV

COMP1

MODE

COMP2

HDMI

RGB-PC

INPUT

POWER

RATIO

+/-

THUMBSTICK

(Up/Down/Left

Right)

ENTER

VOLUME UP

/DOWN

MUTE

FLASHBK

CHANNEL

UP/DOWN

FAV

In AV 1-2, Component 1-2, RGB-PC , HDMI/DVI input sources, screen returns to the last TV channel.

External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI/DVI.

(AV 1-2, Component 1-2, RGB-PC , HDMI/DVI input sources are linked automatically, only if these are connected.)

Turns your TV or any other programmed equipment on or off, depending on the mode.

Change the aspect ratio.

pp..4455

Adjust brightness on screen. It turns to the default settings brightness by changing

mode source.

Navigate the on-screen menus and adjust the system settings to your preference.

Accepts your selection or displays the current mode.

Increase/decrease the sound level.

Switch the sound on or off.

pp..2277

Tune to the last channel viewed.

Select available channels.

Input the channel number.

Scroll through the programmed Favorite channels.

NUMBER button

Introduction

Installing Batteries

■

Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -).

■

Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.

■

Close cover.

TV, DVD, VCR

COMP1

COMP2

HDMI

RGB-PC

EZ PIC

EZ SOUND

ADJUST

INFO

EXIT

SAP

TIMER

Selects the remote operating mode: TV, VCR, DVD. Select other operating modes, for the remote to operate external devices.

Directly, select Component1 input.

Directly, select Component2 input.

Directly, select HDMI/DVI input.

Directly, select RGB input.

Adjust the factory preset picture depend on the viewing environment.(red)

pp..3333

Select the appropriate type of sound for type of program.(green)

pp..3399

Adjust the screen position, size, and phase in PC mode.(yellow)

pp..2266

Display information at the top of the screen. (blue)

Control video cassette recorders or DVD players.

Clear all on-screen displays and return to TV viewing from any menu.

Select a closed caption.

pp..4466 (*In DTV/CADTV modeGGpp..4466)

Displays the main menu.

Analog mode: Selects MTS sound(Mono, Stereo, and a SAP)

DTV mode: Change the audio language.

Select the amount of time before your TV turns off automatically.

pp..4433

VCR/DVD

control buttons

■

Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope.

■

Dispose of used batteries in a recycle bin to preserve environment.

VOL

MENUTV/AV

TVTV

INPUT

DVD

ARC

EXIT

PIP PR +

PIP INPUT

SWAP

PIP PR -

SLEEP

LIST

I/II

TEXT PIP

SIZE

POSITION

VCR

POWER

Remote control effective range

Introduction

ATTACHING THE TV TO A WALL

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

* If your product has the bolts in the eye-bolts position , loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase sepa-

rately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

Installation

For proper ventilation, allow a clearance of 4inches on each side from the wall.

4 inches

Ensure adequate ventilation by following the clearance recommendations.

CAUTION

4 inches

Power Supply

Short-circuit

Breaker

■

This picture shown below may be somewhat different from your TV.

GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

DESKTOP PEDESTAL INSTALLATION

Installation

Antenna Or Cable Connection

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Outdoor Antenna

Wall Antenna Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Turn clockwise to tighten.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

Analog and Digital TV signals provided on antenna

- Antenna or Cable Service without a Cable Box Connection.

- For optimum picture quality, adjust antenna direction if needed.

Analog and DTV signals provided on two separate antennas

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Antenna

RF Coaxial Wire (75 ohm)

• In a poor signal area to improve picture quality, purchase and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your dealer for assistance.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

External Equipment Connections

signal amplifier

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

NOTE: All cables shown are not included with the TV

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

Turn clockwise to tighten.

Analog and Digital TV signals provided on cable

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

Installation

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

VCR Setup

When connecting with an antenna

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

HDMI / DVI IN HDMI / DVI IN

ANTENNA/ANTENNA/ CABLE INCABLE IN

REMOTEREMOTE

CONTROL INCONTROL IN

RS-232C INRS-232C IN

(CONTROL(CONTROL & SER & SERVICE)VICE)

RGB IN

(PC)(PC)

AUDIO INAUDIO IN (RGB/DVI)(RGB/DVI)

SERVICESERVICE

When connecting with a RCA cable

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

HDMI / DVI IN

ANTENNA/

CABLE IN

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN (RGB/DVI)

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1

AV OUT

COMPONENTCOMPONENT IN

DIGITAL AUDIO

OUTOUT

OPTICALPTICAL

SERVICE

VCR

Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

Select AV 1 input source using the INPUT button on the remote control.

- If connected to AV IN2, select AV2 input source.

• If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the

set.

Connect the RF antenna out socket of the VCR to the Antenna socket on the set.

Connect the antenna cable to the RF antenna in socket of the VCR.

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

VCR

Installation

When connecting with an S-Video cable

VIDEO

AUDIOAUDIO

VIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1

AV OUT

COMPONENTCOMPONENT IN

DIGITDIGITALAL AUDIO AUDIO

OUT

OPTICALPTICAL

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

HDMI / DVI IN

ANTENNA/

CABLE IN

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN

(RGB/DVI)

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

SERVICE

VCR

Connect the S-VIDEO output of the VCR to the SVIDEO input on the set. The picture quality is

improved; compared to normal composite (RCA cable) input.

Connect the audio outputs of the VCR to the AUDIO input jacks on the set.

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

Select AV1 input source with using the INPUT button on the remote control.

- If connected to AV IN2, select AV2 input source.

Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.

Camcorder

Video Game Set

Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

Select AV2 input source with using the INPUT button on the remote control.

- If connected to AV I N 1 input, select AV1 input

source.

Operate the corresponding external equipment. Refer to external equipment operating guide.

External AV Source Setup

• This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB and HDMI/DVI sources are connected.

AUDIO VIDEO

Installation

DVD Setup

When connecting with a S-Video cable

HDMI / DVI IN

ANTENNA/ CABLE IN

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1V IN 1

AV OUTV OUT

COMPONENTCOMPONENT IN IN

DIGITDIGITALAL AUDIO AUDIO

OUTOUT

OPTICALPTICAL

VIDEO

AUDIO

COMPONENT IN

S-VIDEO

(R) AUDIO (L)

DVD

Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.

Connect the audio outputs of the DVD to the AUDIO input jacks on the set.

Turn on the DVD player, insert a DVD.

Select AV1 input source with using the INPUT button on the remote control.

- If connected to AV I N 2 , select AV 2 input source.

Refer to the DVD player's manual for operating instructions.

When connecting with a HDMI cable

Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the set.

Select HDMI/DVI input source with using the INPUT button on the remote control.

Refer to the DVD player's manual for operating instructions.

HDMI / DVI IN HDMI / DVI IN

ANTENNA/ANTENNA/

CABLE INCABLE IN

HDMI-DVD OUTPUT

DVD

• TV can receive the video and audio signal simultaneously with using a HDMI cable.

• If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p.

• If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p.

Installation

When connecting with a component cable

Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set.

Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set.

Turn on the DVD player, insert a DVD.

Select Component 1 input source with using the INPUT button on the remote control.

- If connected to COMPONENT IN 2, select Component 2 input source.

Refer to the DVD player's manual for operating instructions.

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Y PB

Component ports on the TV

Y Y Y Y

B-Y

Cb PB

R-Y

Cr P

Video output ports

on DVD player

HDMI / DVI IN

ANTENNA/

CABLE IN

VIDEO

AUDIOAUDIO

COMPONENTCOMPONENT IN

(R) AUDIO (L)

DVD

1 2

Installation

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

HDSTB Setup

When connecting with a HDMI cable

Connect the HDMI output of the digital set-top box to the HDMI/DVI IN jack on the set.

Select HDMI/DVI input source with using the INPUT button on the remote control.

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

Digital Set-top Box

• TV can receive the video and audio signal simultaneously using a HDMI cable.

• If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will

be automatically set to 1280x720p.

• If the digital set-top box does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p.

HDMI-DTV OUTPUT

HDMI / DVI IN HDMI / DVI IN

REMOTEREMOTE

CONTROL INCONTROL IN

RS-232C INRS-232C IN

(CONTROL(CONTROL & SER & SERVICE)VICE)

RGB INRGB IN

(PC)(PC)

AUDIO INAUDIO IN (RGB/DVI)(RGB/DVI)

SERVICESERVICE

When connecting with a Component cable

Connect the video outputs (Y, PB, PR) of the digital set-top box to the COMPONENT IN VIDEO jacks on the set.

Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the set.

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

Select Component 1 input source with using the INPUT button on the remote control.

- If connected to COMPONENT IN 2, select Component 2 input source.

(R) AUDIO (L)

HDMI / DVI IN

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN (RGB/DVI)

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1V IN 1

AV OUTV OUT

COMPONENTCOMPONENT IN

DIGITDIGITALAL AUDIO AUDIO

OUTOUT

OPTICALPTICAL

SERVICE

Signal

480i

480p/720p/1080i

Component1/2

Yes

HDMI/DVI

Yes

Digital Set-top Box

+ 47 hidden pages