LG 42PW450 User manual
OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating the
set and retain it for future reference.
P/NO : MFL67213002 (1104-REV00)
Printed in Thailand
www.lg.com
SAFETY INSTRUCTIONS
2
Please read these safety precautions carefully before using the product.
In this manual, the illustration may be somewhat different from your product because it is
just example to help the instruction.
WARNING
If you ignore the warning message, you may be seriously injured or there is a
possibility of accident or death.
CAUTION
If you ignore the caution message, you may be slightly injured or the product may be damaged.
ENGLISH
ENG
PRECAUTION IN INSTALLING THE PRODUCT
WARNING
Keep away from heat sources like electrical
heaters.
- Electrical shock, fire, malfunction or
deformation may occur.
Do not use the product in damp place such
as a bathroom or any place where it is likely
to get wet.
- This may cause a fire or could give an
electric shock.
If you can smell smoke or other odours or hear
a strange sound unplug the power cord and
contact the service center.
- If you continue to use without taking proper
measures, electrical shock or fire can occur.
CAUTION
Install the product on a flat and stable place
that has no risk of the product dropping.
- If the product is dropped, you may be injured
or the product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in
installation such as bookcase or rack.
- Ventilation required.
As long as this unit is connected to the AC wall outlet, it is
not disconnected from the AC power source even if you
turn off this unit by SWITCH.
PRECAUTIONS WHEN MOVING THE PRODUCT
WARNING
Make sure to turn off the product.
Make sure to remove all cables before
moving the product.
- You may be electrocuted or the product
can be damaged.
CAUTION
Do not impact the product when moving it.
- You may be electrocuted or the product
can be damaged.
Make the panel face forward and hold it
with both hands to move.
- If you drop the product, the damaged
product can cause electric shock or fire.
Contact your nearest service center for
repair.
PRECAUTIONS WHEN USING THE PRODUCT
WARNING
Do not disassemble, repair or modify the
product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check,
calibration or repair.
ELECTRICAL POWER RELATED
PRECAUTIONS
WARNING
Make sure to connect the power cable to a
properly earthed outlet.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered
with dust, dry the power plug completely or wipe
dust off.
- You may be electrocuted due to excess
moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break
out.
CAUTION
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the appliance.
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN /
BURN-IN” ON YOUR TELEVISION SCREEN
-
When a fixed image (e.g. logos, screen menus, video game,
computer display or teletext pages) is displayed on the
television for an extended period it can become permanently
imprinted on the screen. This phenomenon is known as “image
burn” or “burn-in”. Image burn is not covered under the
manufacturer’s warranty.
-
In order to prevent image burn, avoid displaying a fixed
image on your television’s screen for a prolonged period (2 or
more hours for LCD, 1 or more hours for Plasma).
-
Image burn can also occur on the letterboxed areas of
your television if you use the 4:3 aspect ratio setting for an
extended period.
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product.
The illustrations in this manual may differ from the actual product and item.
3
Remote control and
batteries(AAA)
Polishing cloth1 (This item is not
included for all models.)
x 4
M4 x 26 M5 x 14.5 M4 x 28
(Except for 60PV25**,
60PZ55**)
x 3
Screw for assembly
Ferrite core
(Only 60PV25**,
60PZ55**)
Owner’s manual
(Depending on model)
(This item is not included for all
x 4
models.)
x 3
M5 x 24
Power Cord(This item is not included
Cable Holder
for all models.)
Power Cord holder
ENGLISH
ENG
Protection cover
1 Gently wipe the spots on the cabinet with the polishing cloth.
Protection cover
tape
(AG-S250 : Depending on model)
(This item is not included for all
3D Glasses
models.)
CAUTION
Do not use any pirated items to ensure the safety and product life span.
Any damages or injuries by using pirated items are not covered by the warranty.
ASSEMBLING AND PREPARING
4
NOTE
The items supplied with your product may vary depending on the model.
Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
Image shown may differ from your TV.
How to use the ferrite core (Depending on model)
1 Use the ferrite core to reduce the electromagnetic interference in the PC audio cable.
Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV.
ENGLISH
ENG
[to an External device]
[Figure 1]
2 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV.
[to a wall plug] [to the TV]
[Figure 2]
3 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
[to a wall plug]
[Figure 3]
- If there is one ferrite core, follow as shown in Figure 1.
- If there are two ferrite cores, follow as shown in Figures 1 and 2.
- If there are three ferrite cores, follow as shown in Figures 1 and 3.
10 mm(+ / - 5 mm)
[to the TV]
[Cross Section of
Ferrite Core]
[Cross Section of
Ferrite Core]
[to the TV]
[Cross Section of
Ferrite Core]
Separate purchase
Separate purchase items can be changed or modified for quality
improvement without any notification.
Contact your dealer for buying these items.
These devices only work with compatible LG Plasma TV.
(AG-S230, AG-S250, AG-S270 :
3D Glasses
Only 3D Models)
Parts and buttons
NOTE
TV can be placed in standby mode in order to reduce the power consumption. And TV should be
turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
CAUTION
Do not step on the glass stand or subject it to any impact. It may break, causing possible injury
from fragments of glass, or the TV may fall.
Do not drag the TV. The floor or the product may be damaged.
Image shown may differ from your TV.
Only 50/60PV25**, 42/50PT25**
USB input
HDMI IN
AV (Audio and
Video) IN
R
AUDIO
L/MONO
VIDEO
AV IN 2
USB IN
IN 2
Screen
Speakers
ASSEMBLING AND PREPARING
Remote control and
intelligent1 sensors
Power indicator
Red – In Standby
mode
Off – TV turns on
5
INPUT
Y
B
P
VIDEO
R
P
COMPONENT IN
L
AUDIO
R
1
AV IN 1
VIDEO
L/MONO
AUDIO
R
HOME OK
OPTICAL
DIGITAL
AUDIO OUT
RGB IN (PC)
2
(CONTROL & SERVICE)
AUDIO IN
(RGB/DVI)
RS-232C IN
/DVI IN
P
1
ANTENNA
IN
Touch buttons
Connection panel
Button Description
/I Turns the power on or off
INPUT Changes the input source
HOME Accesses the main menus, or saves your input and exits the menus
OK Selects the highlighted menu option or confirms an input
- +
v
P
^
Adjusts the volume level
Scrolls through the saved programmes
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2 Touch Button - You can use the desired button function by touching.
2
ENGLISH
ENG
ASSEMBLING AND PREPARING
6
Image shown may differ from your TV.
Only 42/50PW35**, 42/50PW45**, 50/60PZ55**
Screen
USB input
HDMI IN
AV (Audio and
Video) IN
R
AUDIO
L/MONO
VIDEO
AV IN 2
USB IN
IN 3
Speakers
Remote control and intelligent1 sensors
Power indicator
Red – In Standby
mode
Off – TV turns on
ENGLISH
ENG
Y
B
P
VIDEO
R
P
COMPONENT IN
L
AUDIO
R
1
INPUT
AV IN 1
VIDEO
L/MONO
AUDIO
R
HOME OK
AUDIO OUT
2
OPTICAL
DIGITAL
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
IN
2
1
AUDIO IN
(RGB/DVI)
ANTENNA
P
IN
Touch buttons
Connection panel
Button Description
/I Turns the power on or off
INPUT Changes the input source
HOME Accesses the main menus, or saves your input and exits the menus
OK Selects the highlighted menu option or confirms an input
- +
v
P
^
Adjusts the volume level
Scrolls through the saved programmes
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2 Touch Button - You can use the desired button function by touching.
2
Loading...