OWNER’S MANUAL
LED TV*
* LG LED TVs are LCD TVs with LED backlighting. |
|
||
Please read this manual carefully before operating your TV |
|
||
and retain it for future reference. |
|
||
29LY570H |
32LY560H |
|
|
32LY570H |
39LY560H |
|
|
39LY570H |
42LY560H |
|
|
42LY570H |
47LY560H |
|
|
47LY570H |
|
|
|
55LY570H |
|
|
|
65LY570H |
|
|
|
*MFL68080302* |
|
www.lgsolutions.com |
P/NO : MFL68080302 (1409-REV03)
<![endif]>ENGLISH
2 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
CAUTION
If you ignore the caution message, you may be slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the product safely. Please read the note carefully before using the product.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
••Do not allow the television to become wet.
••Clean only with a dry cloth.
••Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
••Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
••Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet (Can differ by country).
••Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil or pen, or make a scratch on it.
IMPORTANT SAFETY INSTRUCTIONS 3
••Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
••Only use attachments/accessories specified by the manufacturer.
••Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
••Unplug this apparatus during lightning storms or when unused for long periods of time.
••Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
••Do not stick metal objects or any other conductive material into the power cord. Do not touch the end of the power cord while it is plugged in.
••Keep the packing anti-moisture material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, induce vomiting and go to the nearest hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of children.
••CAUTION concerning the Power Cord (Can differ by country):
Check the specification page of this owner’s manual to determine necessary power requirements for this set. Do not connect too many appliances to the same AC
power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and
if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not move the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
••Warning - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.
••Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
<![endif]>ENGLISH
4 IMPORTANT SAFETY INSTRUCTIONS
<![endif]>ENGLISH
••Grounding
(Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock
(i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power
Short-circuit Supply
Breaker
••As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.
••Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification
could void the user’s authority to operate this product.
••Outdoor Antenna Grounding
(Can differ by country):
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges
and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
|
|
|
|
|
|
|
|
|
|
|
|
|
Antenna Lead in Wire |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
Antenna Discharge Unit |
Ground Clamp |
|
|
|
|
|
|
|
|
|
|
|
|
(NEC Section 810-20) |
|
|
|
|
|
|||||||||
Electric Service |
|
|
|
|
|
|
|
|
|
|
Grounding Conductor |
||
|
|
|
|
||||||||||
Equipment |
|
|
|
|
|
|
|
|
(NEC Section 810-21) |
||||
Ground Clamp |
|
|
Power Service Grounding |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Electrode System |
|
|
|
NEC: National Electrical Code |
|
|
||||||||
|
|
|
|
|
(NEC Art 250, Part H) |
••Cleaning
When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners, or benzine.
••Moving
Make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.
••Ventilation
Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places.
••If you smell smoke or other odors coming from the TV, unplug the power cord and contact an authorized service center.
••Keep the product away from direct sunlight.
••Never touch this apparatus or antenna during a lightning storm.
••When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.
••Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.
••DISCONNECTING THE DEVICE FROM THE
MAIN POWER
The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.
••Batteries
Store the accessories (battery, etc.) in a safe location out of the reach of children.
••This apparatus uses batteries. In your community there might be regulations that require you to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.
••Do not dispose of batteries in a fire.
••Do not short circuit, disassemble, or allow the batteries to overheat.
••Do not use high voltage electrical equipment near the TV, (e.g. bug zapper). This may result in product malfunction.
IMPORTANT SAFETY INSTRUCTIONS 5
••Dot Defect
The panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV.
Those dots are deactivated pixels and do not affect the performance and reliability of the TV.
••Generated Sound
Cracking noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount
of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.
••Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.
••Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot. This does not affect the performance of the product or cause defects in the product.
••If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
Preventing image burn or burn-in on your TV screen
••If a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty.
••If the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.
••Avoid displaying a fixed image on the TV screen for a long period of time to prevent image burn.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 IMPORTANT SAFETY INSTRUCTIONS
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
LG Recycling Policy
LG Electronics offers a customized e-waste take-back and recycling service that meets local needs and requirements in the countries where e-waste regulations are in place, and also provides
product and packaging take-back and recycling service voluntarily in some countries. LG Electronics evaluates products’ recyclability at the design step using LG’s recyclability evaluation tool, with the goal of improving recyclability where practicable. Through these activities, LG seeks to contribute to conserving natural resources and protecting the environment.
For more information about the LG Recycling Policy, please visit our global site at http://www.lg.com/global/sustainability/environment/take-back-recycling .
LICENSES / OPEN SOURCE SOFTWARE NOTICE 7
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that has passed rigorous testing to verify that it plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device
setup menu. Go to vod.divx.com for more information on how to complete your registration.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
<![endif]>ENGLISH
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
NOTE
••Image shown may differ from your TV.
••Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
••The available menus and options may differ from the input source or product model that you are using.
••New features may be added to this TV in the future.
8 TABLE OF CONTENTS
TABLE OF CONTENTS
2IMPORTANT SAFETY INSTRUCTIONS
7 LICENSES
<![endif]>ENGLISH
7OPEN SOURCE SOFTWARE NOTICE
8TABLE OF CONTENTS
9ASSEMBLING AND PREPARING
9 Unpacking
11Parts and Buttons
12- Using the Joystick Button
14Lifting and Moving the TV
15Setting up the TV
15- Attaching the Stand
18- Mounting on a Table
21- Mounting on a Wall
22 MAKING CONNECTIONS
22Connecting to an Antenna or Cable
23Other Connections
25REMOTE CONTROL
26MAINTENANCE
26 Cleaning your TV
26- Screen, Frame, Cabinet, and Stand
26- Power Cord
27TROUBLESHOOTING
28SPECIFICATIONS
ASSEMBLING AND PREPARING 9
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
(For
32/39/42/47/55/65LY570H,
32/39/42/47LY560H)
Remote Control,
Batteries (AAA)
(For 29LY570H)
Power Cord, AC/DC Adapter
(Depending upon model)
(For 29LY570H)
Stand Base
|
|
|
|
|
Owner’s Manual |
Power Cord |
|||
|
|
|
|
|
(For 32/39/42/47/55LY570H, |
(For 65LY570H) |
|||
32/39/42/47LY560H) |
|
Stand Base, Stand Body |
|
Stand Base, Stand Body |
|
|
|
|
|
|
(For 32/39LY570H, |
|
(For 42/47/55LY570H, |
32/39LY560H) |
|
42/47LY560H) |
Stand Screws |
Stand Screws |
|
6 EA, M4 x L20 |
4 EA, M4 x L20 |
|
|
|
4 EA, M4 x L14 |
<![endif]>ENGLISH
10 ASSEMBLING AND PREPARING
<![endif]>ENGLISH
(For 65LY570H) |
(For 65LY570H) |
(For 32/39/42/47/55LY570H, |
|
|
32/39/42/47LY560H) |
Stand Screws |
|
Stand Holder |
Rubber |
|
4 EA, M4 x L14 |
|
2 EA |
|
2 EA |
(For 32/39/42/47/55LY570H, |
|
(For 32/39/42/47/55LY570H, |
(For 32/39/42/47/55LY570H, |
|
32/39/42/47LY560H) |
|
32/39/42/47LY560H) |
32/39/42/47LY560H) |
Torx Plus |
|
Screws for Stand Fixing |
|
Washers for Stand Fixing |
Star-Head Screw |
|
2 EA |
|
2 EA |
2 EA |
|
|
|
|
|
|
|
|
|
(For 32/39/42/47/55LY570H, |
|
(For 39/42/47/55LY570H, |
|
(For |
32/39/42/47LY560H) |
|
39/42/47LY560H) |
|
32/39/42/47/55/65LY570H, |
|
|
|
|
32/39/42/47LY560H) |
Nuts for Stand Fixing |
Power Cord Holder and |
|
Cable Holder |
|
2 EA |
Screw |
|
1 EA |
|
|
|
1 EA |
|
(Depending upon model) |
|
|
|
|
|
(For 42LY570H, 42LY560H) |
(For 47/55/65LY570H, |
|
|
|
|
|
47LY560H) |
|
|
Wall Mount Spacers |
Wall Mount Spacers |
|
6 EA |
|
4 EA |