QUICK REFERENCE GUIDE
LED LCD TV
Please read this manual carefully before operating your set and retain it for future reference.
32LT560E
42LT560E
P/NO : MFL67415417 (1209-REV00) |
www.lg.com |
<![endif]>ENGLISH
2 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
yyDo not use this apparatus near water.
yyClean only with a dry cloth.
yyDo not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
yyDo not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
yyDo not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet (Can differ by country).
|
|
|
|
|
|
|
|
|
|
|
|
IMPORTANT SAFETY INSTRUCTIONS 3 |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
yyProtect the power cord from being walked on |
yyKeep the packing anti-moisture material or |
|||||||||||||||||||
or pinched particularly at plugs, convenience |
vinyl packing out of the reach of children. |
|||||||||||||||||||
receptacles, and the point where they exit |
Anti-moisture material is harmful if |
|||||||||||||||||||
from the apparatus. |
swallowed. If swallowed by mistake, force |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
the patient to vomit and visit the nearest |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
hospital. Additionally, vinyl packing can |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
cause suffocation. Keep it out of the reach of |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
children. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
yyOnly use attachments/accessories specified |
yyCAUTION concerning the Power Cord |
|||||||||||||||||||
by the manufacturer. |
(Can differ by country): |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
It is recommended that appliances be |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
placed upon a dedicated circuit; that is, a |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
single outlet circuit which powers only that |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
yyUse only with a cart, stand, tripod, bracket, |
appliance and has no additional outlets or |
|||||||||||||||||||
or table specified by the manufacturer, or |
branch circuits. Check the specification page |
|||||||||||||||||||
sold with the apparatus. When a cart is used, |
of this owner’s manual to be certain. Do not |
|||||||||||||||||||
use caution when moving the cart/apparatus |
connect too many appliances to the same |
|||||||||||||||||||
combination to avoid injury from tip-over. |
AC power outlet as this could result in fire or |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
electric shock. Do not overload wall outlets. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
Overloaded wall outlets, loose or damaged |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
wall outlets, extension cords, frayed power |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
cords, or damaged or cracked wire insulation |
||||||||
yyUnplug this apparatus during lightning |
are dangerous. Any of these conditions could |
|||||||||||||||||||
storms or when unused for long periods of |
result in electric shock or fire. Periodically |
|||||||||||||||||||
time. |
examine the cord of your appliance, and |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
if its appearance indicates damage or |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
deterioration, unplug it, discontinue use of |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
the appliance, and have the cord replaced |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
with an exact replacement part by an |
||||||||
yyRefer all servicing to qualified service |
authorized service. Protect the power cord |
|||||||||||||||||||
personnel. Servicing is required when |
from physical or mechanical abuse, such as |
|||||||||||||||||||
the apparatus has been damaged in any |
being twisted, kinked, pinched, closed in a |
|||||||||||||||||||
way, such as power-supply cord or plug is |
door, or walked upon. Pay particular attention |
|||||||||||||||||||
damaged, liquid has been spilled or objects |
to plugs, wall outlets, and the point where |
|||||||||||||||||||
have fallen into the apparatus, the apparatus |
the cord exits the appliance. Do not move |
|||||||||||||||||||
has been exposed to rain or moisture, does |
the TV with the power cord plugged in. Do |
|||||||||||||||||||
not operate normally, or has been dropped. |
not use a damaged or loose power cord. Be |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
sure do grasp the plug when unplugging the |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
power cord. Do not pull on the power cord |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
to unplug the TV. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
yyDo not stick metal objects or any other |
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
||||||||||||
conductive material into the power cord. Do |
|
|
|
|
|
|
|
|
|
|||||||||||
not touch the end of the power cord while it |
|
|
|
|
|
|
|
|
|
|||||||||||
is plugged in. |
|
|
|
|
|
|
|
|
|
<![endif]>ENGLISH
<![endif]>ENGLISH
4 IMPORTANT SAFETY INSTRUCTIONS
yyWarning - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.
yyDo not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
yyGrounding
(Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock
(i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power Supply
Short-circuit
Breaker
yyDISCONNECTING DEVICE FROM THE MAIN POWER
Mains plug is the disconnecting device. The plug must remain readily operable.
yyAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.
yyDo not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
yyANTENNAS Outdoor antenna grounding
(Can differ by country):
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges
and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
Ground Clamp |
|
|
|
|
|
|
|
|
|
|
Antenna Lead in Wire |
||
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
Antenna Discharge Unit |
||||||||
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Electric Service |
|
|
|
|
|
|
|
|
|
|
|
|
(NEC Section 810-20) |
Equipment |
|
|
|
|
|
|
|
|
|
Grounding Conductor |
|||
Ground Clamp |
|
|
|
|
|
|
|
|
|
|
|
(NEC Section 810-21) |
|
|
|
|
|
|
|
|
|
|
Power Service Grounding
NEC: National Electrical Code Electrode System
(NEC Art 250, Part H)
yyCleaning
When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzine.
yyMoving
Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.
yyVentilation
Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places.
IMPORTANT SAFETY INSTRUCTIONS 5
yyIf you smell smoke or other odors coming from the TV, unplug the power cord and contact an authorized service center.
yyDo not press strongly upon the panel with a hand or a sharp object such as a nail, pencil or pen, or make a scratch on it.
yyKeep the product away from direct sunlight.
yyNever touch this apparatus or antenna during a thunder or lightning storm.
yyWhen mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.
yyDo not allow an impact shock or any objects to fall into the product, and do not drop anything onto the screen.
yyDot Defect
The Plasma or LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is generated from a highspeed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
yyTake care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot. This does not affect the performance of the product or cause defects in the product.
yyIf the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
DISPOSAL (Hg lamp only used in LCD TVs)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
Preventing “Image burn” or “Burn-in” on your TV screen
yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.
yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.
yyAvoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model. For more information about licenses, visit 'www.lg.com'.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit 'http://opensource.lge.com'.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
TABLE OF CONTENTS 7
TABLE OF CONTENTS
2 IMPORTANT SAFETY INSTRUCTIONS
6 LICENSES
6OPEN SOURCE SOFTWARE NOTICE
7TABLE OF CONTENTS
8INSTALLATION PROCEDURE
8 ASSEMBLING AND PREPARING
8Unpacking
9Optional Extras
10Parts and buttons
11Setting up the TV
11- Attaching the stand
12- Mounting on a table
13- Mounting on a wall
14- Tidying cables
15REMOTE CONTROL
17GENERAL TROUBLESHOOTING
18CAUTION for using ezsign 2.0
19SPECIFICATIONS
20IR CODES
21EXTERNAL CONTROL DEVICE SETUP
21RS-232C Setup
21Type of connector; D-Sub 9-Pin Male
22RS-232C configurations
23Communication Parameters
23Command reference list
24Transmission / Receiving protocol
NOTE
yyImage shown may differ from your TV. yyYour TV’s OSD (On Screen Display) may differ slightly from that shown in this
manual.
yyThe available menus and options may differ from the input source or product model that you are using.
yyNew features may be added to this TV in the future.
<![endif]>ENGLISH
<![endif]>ENGLISH
8 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
INSTALLATION PROCEDURE
1Open the package and make sure all the accessories are included.
2Attach the stand to the TV set.
3Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yyTo ensure safety and product life span, do not use any unapproved items.
yyAny damages or injuries sustained due to use of unapproved items are not covered by the warranty. yyIn the case of some models, the thin film on the screen is a part of TV and should not be removed.
NOTE
yyThe items supplied with your product will vary depending on the model.
yyProduct specifications and/or manual contents subject to change without prior notice due to upgrade of product functions.
ASSEMBLING AND PREPARING 9
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Quick Reference Guide |
|
EzSign 2.0 Editor CD |
|
Power Cord |
||
Remote control, |
|
|
|
|||||||||||
Batteries (AAA) |
|
|
|
|
|
|
|
|
||||||
(See p.15) |
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Stand body/Stand base |
|
Stand Screws |
|
Desk-mount Screw |
|
Protection cover |
(See p.11) |
|
8 EA, M4 x 14 |
|
(See p.12) |
|
|
|
|
(See p.11) |
|
|
|
|
|
|
|
|
|
|
|
<![endif]>ENGLISH
Power Cord holder |
|
Cable holder |
(See p.14) |
|
(See p.14) |
|
|
|
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items.
These devices only work with certain models.
AN-WF100
Wireless Dongle
<![endif]>ENGLISH
10 ASSEMBLING AND PREPARING
Parts and buttons
Side Connection panel
USB |
<![if ! IE]> <![endif]>USB |
input |
|
HDMI |
<![if ! IE]> <![endif]>3 |
|
|
input |
|
Buttons
Remote control
Power indicator Screen
Speakers
/ DVI IN
1 |
2 |
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
OAV IN |
|
<![if ! IE]> <![endif]>VIDE |
|
<![if ! IE]> <![endif]>L/MONO |
<![if ! IE]> <![endif]>L |
<![if ! IE]> <![endif]>AUDIO- |
<![if ! IE]> <![endif]>R |
<![if ! IE]> <![endif]>R- |
|
AUDIO IN (RGB/DVI)
ANTENNA |
CABLE |
IN |
IN |
Rear Connection panel
|
Button |
Description |
|
|
|
^ |
v |
Scrolls through the saved channels. |
+ |
- |
Adjusts the volume level. |
|
|
|
|
|
Turns the power on or off. |
|
|
|
ASSEMBLING AND PREPARING 11
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
1
4 EA
M4 x 14
Stand Body
Front
Stand Base
2
Caution
yyWhen attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.
3
4 EA
M4 x 14
CAUTION
yyMake sure that the screws are fastened completely. (If they are not fastened securely enough, the TV may tilt forward after being installed.)
yyDo not fasten the screws with too much force; otherwise they may be worn out and get loosened.
<![endif]>ENGLISH
12 ASSEMBLING AND PREPARING
Mounting on a table
1Lift and tilt the TV into its upright position on a table.
- Leave a 10 cm (4 inch) (minimum) space from
Securing the TV to a table
Fix the TV to a table to prevent from tilting forward, damage, and potential injury.
To secure the TV to a table, insert and tighten the supplied screw on the rear of the stand.
10
<![endif]>ENGLISH
2 Connect the power cord to a wall outlet.
Caution
yyDo not place the TV near or on sources of heat, as this may result in fire or other damage.
Adjusting the angle of the TV to suit view
(Depending on model)
Swivel 90 degrees to the left or right and adjust the angle of the TV
CAUTION
adjusting the angle of the TV, watch out for your fingers.
-Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury.
warning
yyTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury.
Attaching the TV to a desk
The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
4-Screws
(Not provided as parts of the product)
Stand
Desk
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel.
LG recommends that wall mounting be performed by a qualified professional installer.
10 cm
10 cm 10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
Model |
32LT560E |
42LT560E |
VESA |
200 x 100 |
200 x 200 |
Standard screw |
M4 |
M6 |
Number of screws |
4 |
4 |
Wall mount bracket LSW100B(G) |
LSW200BX(G) |
|
(optional) |
|
|
|
|
LSW220BX |
ASSEMBLING AND PREPARING 13
Caution
yyDisconnect the power first, and then move or install the TV. Otherwise electric shock may occur.
yyIf you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.
yyDo not over tighten the screws as this may cause damage to the TV and void your warranty.
yyOnly use screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
NOTE
yyUse screws that are listed on the VESA standard screw specifications.
yyThe wall mount kit includes an installation manual and necessary parts.
yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.
yyThe length of screws may differ depending on the wall mount. Make sure to use the proper length.
yyFor more information, refer to the manual supplied with the wall mount bracket.
<![endif]>ENGLISH
<![endif]>ENGLISH
14 ASSEMBLING AND PREPARING
Securing the TV to a wall (optional)
(Depending on model)
1Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.
-If there are bolts inserted at the eye-bolts position, remove the bolts first.
2Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear of the TV.
3Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
sure that children do not climb on or hang on the TV.
NOTE
a platform or cabinet that is strong and large enough to support the TV securely.
yyBrackets, bolts and ropes are optional. You can obtain additional accessories from your local dealer.
Tidying cables
1Install the power cord holder and power cord. It will help prevent the power cable from being
Power cord holder
2Gather and bind the cables with the cable holder.
Cable holder
REMOTE CONTROL 15
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
Make sure to point the remote control toward at the remote control sensor on the TV.
ENERGY AV MODE INPUT
TV
SAVING
1 2 3
4 5 6
7 8 9
0 Q.VIEW
LIST
POWER
Turns the TV on or off.
ENERGY SAVING
Adjusts the Energy Saving settings.
AV MODE
Selects an AV mode.
INPUT
Rotates through inputs.
Also switches the TV on from standby.
TV
Returns to the last TV channel.
Number button
Enters channel numbers or other numbers required.
LIST
Accesses the saved channel list.
- (Dash)
Inserts a dash between numbers such as 2-1 and 2-2.
Q.VIEW
Alternates between the two last channels selected (pressing repeatedly).
<![endif]>ENGLISH
<![endif]>ENGLISH
16 REMOTE CONTROL
FAV
P
VOL PORTAL CH A
G
E
MUTE
SETTINGS GUIDE Q.MENU
OK
INFO EXIT
RATIO
Or
MARK
FAV
P
VOL PORTAL CH A
G
E
MUTE
MENU GUIDE Q.MENU
ENTER
BACK INFO EXIT
VOL
Adjusts the volume level.
FAV / MARK
FAV: Accesses your favorite channel list.
MARK: Selects a menu or option.
PORTAL
Displays the EzSign content on a TV screen.
MUTE
Mutes all sounds.
CH
Scrolls through the saved channels.
PAGE
Moves to the previous or next screen.
SETTINGS or MENU
Accesses the main menu.
GUIDE
Shows Contents List in EzSign mode.
Q.MENU
Accesses the quick menu.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK or ENTER
Selects menus or options and confirms your input.
or BACK
Returns to the previous level.
INFO
Shows or hides the information on TV remote control buttons in EzSign mode.
EXIT
Clears all on-screen displays and returns to TV viewing.
Color buttons
These access special functions in some menus.
VCR/DVD/USB control buttons
Controls video cassette recorders or DVD players or USB. Not functional when EzSign contents is on..
Accesses the AV devices connected to the TV;
Opens the SIMPLINK menu.
RATIO
Resizes an image.
RATIO
|
|
|
|
GENERAL TROUBLESHOOTING 17 |
|
GENERAL TROUBLESHOOTING |
|
||||
|
|
|
|
||
|
Installation |
|
|
|
|
|
|
|
|
||
|
Symptom |
Possible Cause(s) |
Possible Solution(s) |
||
Cannot direct enter |
yy(TV in Pass-through Mode) Installer |
yyIf the channel lineup is locked, only channels |
|||
channel number. |
Menu item 028 CH. OVERIDE is set |
that are active in the TV’s channel lineup can |
|||
|
|
|
to 0, i.e., disabled (recommended |
be selected. Set Installer Menu item 028 CH. |
|
|
|
|
setting). |
OVERIDE to 1 to allow access for direct keypad |
|
|
|
|
|
entry to all channels. |
|
|
|
|
yy(TV in FTG Mode) The channel entered yyChannel access is restricted to channels |
||
|
|
|
is not part of the FTG Channel Map. |
included in the FTG Channel Map. If necessary, |
|
|
|
|
|
make changes to the FTG Channel Map using |
|
|
|
|
|
the FTG File Manager or the FTG Configuration |
|
|
|
|
|
Application, as appropriate. |
No channels present after yyAuto Tuning (Channel Search) not run. yyRefer to Express Script or Custom Master TV setup. Setup procedure, as appropriate. Auto Tuning
must be run in order for the channel lineup to be populated. Note for Express Script: You
must select “Execute Auto Search” in the Auto Search screen to run the search. To re-activate the Express Script, set Installer Menu item 117 FACT DEFAULT to 001.
Picture Reception and Sound
Symptom |
Possible Cause(s) |
Possible Solution(s) |
No picture. |
yyTV is turned OFF. |
yyTurn TV ON. |
|
|
yyPower failure? |
|
yyAntenna/cable not connected. |
yyConnect antenna/cable signal to TV. |
|
yyConnections incorrect. |
yyCheck connections on TV. |
|
yyMPI not connected |
yyIf applicable, connect MPI cable to MPI device. |
|
yyEncrypted program. |
yyTry another channel. |
|
yyWrong tuning band. |
yyAdjust Installer Menu settings. |
Normal picture, poor or |
yyBroadcast problem. |
yyTry a different channel. |
no sound. |
yyAudio muted |
yyPress MUTE or use Volume Up key to increase |
|
||
|
|
sound level. |
|
yyPillow/TV speaker not configured |
yyCheck that Installer Menu items 020 FEATURE |
|
properly. |
LEVEL and 027 HOSPITAL MODE are set as |
|
|
required. Also, if applicable, select TV Speaker in |
|
|
the Audio Menu. |
Erratic Operation
Symptom |
Possible Cause(s) |
Possible Solution(s) |
Installer Menu setup. |
yyWrong Installer Menu settings. |
yyAdjust Installer Menu settings as required. |
<![endif]>ENGLISH
18 GENERAL TROUBLESHOOTING / CAUTION FOR USING EZSIGN 2.0
Installer Remote
Symptom |
Possible Cause(s) |
Possible Solution(s) |
Remote doesn’t work. |
yyRemote not in TV Mode. |
yyUse MODE key to select “TV”; puts remote into |
|
|
TV Mode. |
|
yyNot aimed at IR remote sensor. |
yyPoint remote at TV’s IR receiver on TV. |
|
yyRemote too far from IR sensor. |
yyMove remote closer to TV’s IR receiver or darken |
|
|
room. |
|
yyMPI not connected. |
yyIf applicable, connect MPI cable to MPI device. |
|
yyIR path to TV’s receiver obstructed. |
yyRemove obstructions. |
|
yyWeak batteries. |
yyReplace batteries. |
|
yyWrong battery polarity. |
yyCheck that “+” and “-” match in battery |
|
|
compartment. |
|
yyToo much light in room. |
yyDim room light. |
|
yyWrong Installer Remote. |
yyRequires compatible Installer Remote. Contact |
|
|
your LG dealer. |
|
yyBed Switch set to wrong bed. |
yySet Bed Switch or update Installer Menu, as |
|
|
necessary. |
<![endif]>ENGLISH
CAUTION for using ezsign 2.0
yyDo not remove a USB drive while data is being copied. It can corrupt the data and EzSign may not work properly. yyWhile loading a USB device or dongle, your TV may function slower than normal.
yyWhile EzSign contents is running, the movie with internal subtitles is not supported in USB mode. EzSign TV supports only external subtitles.
(External Subtitle format: *.smi/*.srt/*.sub(MicroDVD, Subviewer 1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.psb(PowerDivX) yySome user-created subtitles may not work properly.
yySome special characters are not supported in subtitles. yyHTML tags are not supported in subtitles.
yySubtitles in languages other than the supported languages are not available.
yyEzSign 2.0 TV function does not work before completing the initial setup Wizard. Make sure to complete the initial setup Wizard by turning on the TV after installation.
yyIf the time is set according to the TV signal, it may not appeared exactly for some region. In that case, set the time manually.
yyIt is recommended that you copy files to the TV memory before playing them, as playing directly from the USB memory for an extended period of time may cause the device to overheat.
yyIn EzSign 2.0 TV mode, some remote control keys may not work.
yyEzSign 2.0 TV dose not support the USB HUB. It is recommended that you connect a USB device directly to the TV without using a USB extension cable as it may not work properly.
yyIt is recommended that you use EzSign 2.0 TV within 8 hours per day as it is standard. yyRefer to the EzSign 2.0 Editor user guide for details.
yyEzSign 2.0 TV does not support Store Demo.