LG 32LRSMT, 42LRSMT User Manual

LCD TV

OWNER’S MANUAL

LCD TV MODELS

32LC5DC

37LC5DC

42LC5DC

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer

when you require service.

www.lgcommercial.com

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

CAUTION / WARNING

1

SAFETY INSTRUCTION

CAUTION / WARNING

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.

The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may

be placed immediately adjacentw		ato that safety instruction :
		n
ne		u
r			al
	M
	a
	n
		u
		al

all warnings.

all instructions.

1

Ow n er

erM a n u al

5Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

2Clean only with dry cloth.

Do not block any ventilation openings. Install in

3accordance with the manufacturer’s instructions.

4Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

6Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

7Only use attachments/accessories specified by the manufacturer.

Ow n erM a n u al

2

8

with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

9Unplug this apparatus during lightning storms or when unused for long periods of time.

10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

			an autho-
			cord from
	physical or mechanical abuse, such as being
	twisted, kinked, pinched, closed in a door, or
	walked upon. Pay particular attention to plugs,
					WARNING
	wall outlets, and the point where the cord exits
	the appliance.
					/
					CAUTION
	Outdoor Use Marking :
	12 WARNING - To Reduce The Risk Of Fire Or
	Electric Shock, Do Not Expose This Appliance
	To Rain Or Moisture

13	Wet Location Marking : Apparatus shall not be
	exposed to dripping or splashing and no

objects filled with liquids, such as vases, shall be placed on or over apparatus.

11 CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced

14 GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

15 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.

3

CONTENTS
	WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .	1
	SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . .	. 2
	INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 6
	Feature of this TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 6
CONTENTS
	PREPARATION
	Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 7
	Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 8
	Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	. 9
	Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . .	10
	Attaching the TV to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	11
	Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	11
	Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	12
	VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	13
	Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .	13
	Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . .	14

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

- Auto Scan (EZ Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

- Add / Delete Channel (Manual Scan) . . . . . . . . . 31

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Channel Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

PICTURE CONTROL

Watching PIP (Picture-In-Picture)/

POP (Picture-Out-Picture) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 37

Preset Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

- EZ Picture - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

- Color Tone - Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Manual Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

- EZ Picture - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

XD - Picture Improvement Technology . . . . . . . . . . . . . 42

Advanced - Cinema 3:2 Pull Down Mode . . . . . . . . . 43

Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 44

Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SOUND & LANGUAGE CONTROL

Auto Volume Leveller (EZ SoundRite) . . . . . . . . . . . . . . . 46

Preset Sound Setting (EZ Sound) . . . . . . . . . . . . . . . . . . . . . 47

Sound Setting Adjustment - User Mode . . . . . . . . . . . 48

Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

On-Screen Menus Language Selection . . . . . . . . . . . . . . 53

Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

- Analog Broadcasting System Captions . . . . . . . 54

- Digital Broadcasting System Captions . . . . . . . . 55

Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

4

TIME SETTING

Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

SCREEN ADJUSTMENT

Auto Configure (RGB(PC) Mode only) . . . . . . . . . . . . . 62

Manual Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Selecting XGA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Initializing (Reset to Original Factory Settings) . 65

PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . .	66
- Setting up Your Password . . . . . . . . . . . . . . . . . . . . . . . . .	66
- Set Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	67
- Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	67
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	68
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	68
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	69
- Movie Rating (MPAA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .	69
- TV Rating Children & General (for USA only) . .	70
- TV Rating English & French (for Canada only) . .	71

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

CONTENTS

5

INTRODUCTION

FEATURE OF THIS TV

INTRODUCTION	of roughly a million or more pixels, 16:9 aspect-ratio
	LG's own special digital image generator, consisting
	of a full digital image processor, six different main
	picture quality factors.
	High-definition television. High-resolution digital
	television broadcast and playback system composed
	screens, and AC3 digital audio. A subset of digital
	television, HDTV formats include 1080i and 720p
	resolutions.

Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.

is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

It has 2 HDMI ports that connect audio and video devices with one cable and produces the highest quality digital images and sound.

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

On Disposal

a.The fluorescent lamp used in this product contains a small amount of mercury.

b.Do not dispose of this product with general household waste.

c.Disposal of this product must be carried out in accordance to the regulations of your local authority.

6

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.

User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

Owner's Manual

Owner’s Manual

INPUT			MODE
TV	POWER		TV
INPUT			DVD
MULTI			VCR
PIP	PIP CH -	PIP CH +	PIP INPUT
EZ PIC EZ SOUND		SWAP	INFO
CC	MENU RATIO
EXIT			SAP

			ENTER
1.5V	1.5V	VOL		CH	PAGE
		7	8	9
		1	2	3
		4	5	6
			0

Batteries

Remote Control

Power Cord

32/37 inches model only

2- TV Bracket Bolts	2- TV Brackets,
	2- Wall Brackets

Option Extras

Polishing Cloth

D-sub 15 pin Cable

*Slightly wipe stained spot on the exterior only with the polishing cloth for the product exterior if there is stain or fingerprint on surface of the exterior.

*Do not wipe roughly when removing stain. Please be cautions of that excessive power may cause scratch or discoloration.

PREPARATION

7

PREPARATION

FRONT PANEL INFORMATION

■ Here shown may be somewhat different from your TV.

Front Panel Controls

PREPARATION

CH

VOL

ENTER

MENU

INPUT

If your TV stand has a protection film, remove it attached to the stand.

Then wipe the stand with polishing cloth.

Remote Control Sensor

Power Standby Indicator

Illuminates red in standby mode. When the TV is turned on, the indicator blinks green and then illuminates green before the picture is displayed.

CHANNEL Buttons

VOLUME Buttons

ENTER Button

MENU Button

INPUT Button

ON/OFF Button

8

BACK PANEL INFORMATION

				S-VIDEO	S-VIDEO Input
					Provides better picture quality than the
			R		video input.
			AUDIO		AUDIO Input
			L/MONO
					VIDEO Input
			VIDEO
					Connects the video signal from a video
11				AV IN 2	device.
	2
					4
1	DIGITAL
	AUDIO		3		RESET
									5
		OUT
HDMI/DVI IN							SERVICE ONLY
			M.P.I.			REMOTE
1(DVI)	2				UPDATE	CONTROL
						OUT
							RGB IN		6
	(	)			(MONO)	VIDEO	SPEAKER	AUDIO
	VIDEO		AUDIO	S-VIDEO
RJP					AUDIO
	COMPONENT IN				AV IN 1		OUT	IN
INTERFACE
								(RGB, DVI)
10			9		8
1				8

Connect a HDMI (DVI) connection to either input.

2

Connect digital audio from various types of equipment.

Note: In standby mode, these ports do not work.

3 M.P.I

4 RESET/UPDATE/REMOTE CONTROL OUT

5 SERVICE ONLY

6RGB IN (PC)

Connect the output from a PC.

AUDIO IN (RGB, DVI)

Connect the audio from a PC or DTV.

7 SPEAKER OUT 8Ω

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

9COMPONENT IN

Connect a component video/audio device to these jacks.

10RJP INTERFACE

11Power Cord Socket

For operation with AC power.

Caution: Never attempt to operate the TV on DC power.

12ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

PREPARATION

9

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

1the cables as necessary.

an additional equipment, see the External equipment Connections section.

PREPARATION

2Install the CABLE MANAGEMENT as shown.

3

CABLE

NOTE

G Do not hold the CABLE MANAGEMENT when moving the product.

- If the product is dropped, you may be injured or the	TWISTER HOLDER
product may be broken.

How to remove the CABLE MANAGEMENT

G Hold the CABLE MANAGEMENT with both hands and pull it backward.

10

ATTACHING THE TV TO A WALL

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product.

Caution: Please make sure that children don’t climb on or hang from the TV.

PREPARATION

■ Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

SWIVEL STAND

20°

The TV can be conveniently swivelled on its stand 20° to the left or right to provide the optimum viewing angle.

11

PREPARATION

PREPARATION

STAND INSTALLATION (Only 32/37 inches LCD TV models)

down on product and

screen from damage.

Assemble the product stand with the product as shown.

3Securely install the 4 bolts provided.

12

VESA WALL MOUNTING

This product accepts a VESA-compliant mounting interface pad. (optional) There 4 threaded holes are available for attaching the bracket.

32 inches			37/42 inches
		200 mm			600 mm

100 mm

400 mm

! NOTE

G Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide.

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4inches on each side from the wall.

4 inches

4 inches

4 inches

4

inches

CAUTION

G Ensure adequate ventilation by following the clearance recommendations.

PREPARATION

13

PREPARATION

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connections.

For optimum picture quality, adjust antenna direction if needed.

Wall	Multi-family Dwellings/Apartments
	(Connect to wall antenna socket)
Antenna
Socket	ANTENNA/
	CABLE IN

Outdoor	RF Coaxial Wire (75 ohm)
Antenna
(VHF, UHF)	Single-family Dwellings /Houses	Copper Wire
	(Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire when connecting the antenna.

2. Cable

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

3. Using both cable and antenna

Antenna

RF Coaxial Wire (75 ohm)

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

UHF

	Antenna	Signal
		Amplifier
		VHF

ANTENNA/

CABLE IN

ANTENNA/

Diplexer CABLE IN (Signal

Combinner)

ANTENNA/

CABLE IN

■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■If the antenna is not installed properly, contact your dealer for assistance.

!NOTE G The TV will let you know when the analog, cable, and digital channel scans are complete.

14

EXTERNAL EQUIPMENT SETUP

■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

When connecting Component cable

1.How to connect

1 Connect the video outputs (Y, PB, PR) of the digital set top box to the COMPONENT IN VIDEO jacks on the set. Match the jack colors

(Y = green, PB = blue, and PR = red).

box to

2.How to use

■Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

■Select Component input source with using the INPUT button on the remote control.

Y PR L R

12

	DIGITAL
	AUDIO
	OUT
HDMI/DVI	(OPTICAL)
	I.

1(DVI)

RJP	VIDEO	AUDIO	S-VIDEO
RFACE	COMPONENT IN

	Signal	Component	HDMI1/DVI,
			HDMI2
		Yes	No
	480i
	480p	Yes	Yes
	720p	Yes	Yes
	1080i	Yes	Yes

SETUP EQUIPMENT EXTERNAL

15

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

When connecting HDMI cable

1.How to connect

1 Connect the digital set-top box to HDMI/DVI IN 1(DVI) or 2 jack on the set.

necessary.

2.to use

on the digital set-top box.

to the owner’s manual for the digital set-top box.)

HDMI1/DVI or HDMI2 input source with using

! NOTE

G When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player output resolution will be automatically set to 720p.

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

			DIGITAL
			AUDIO
			OUT
	HDMI/DVI IN		(OPTICAL)
			M.P.I
	1(DVI)		2
	RJP	VIDEO	AUDIO
		COMPONENT IN
	INTERFACE
	1

HDMI-DTV OUTPUT

16

When connecting HDMI to DVI cable
		DIGITAL
		AUDIO		RESET
		OUT
						SERVICE ONLY
HDMI/DVI IN		(OPTICAL)			REMOTE
		M.P.I.
1(DVI)	VIDEO	2	S-VIDEO	AUDIO	CONTROL	SPEAKER	EXTERNAL
		AUDIO			OUT
				UPDATE
						RGB IN
				(MONO)	VIDEO
RJP	COMPONENT IN			AV IN 1		OUT	SETUPEQUIPMENT
INTERFACE
						8
							DVI)
1
				2

DVI-	OUTPUT			L	R

1. How to connect

1 Connect the

output of the digital set-top box to the HDMI/DVI IN 1(DVI) or 2 jack on the set.

the audio output of the digital set-top box to the AUDIO IN (RGB,DVI) jack on the set.

2.How to use

■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

■Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.

17

EXTERNAL EQUIPMENT SETUP

SETUP EQUIPMENT EXTERNAL

DVD SETUP

When connecting Component cable

1. How to connect

1	Connect the video outputs (Y, PB, PR) of the DVD	to
	the COMPONENT IN VIDEO jacks on the set.	Y	PR L R
	Match the jack colors
	(Y = green, PB = blue, and PR = red).

2. How to use

on the DVD player, insert a DVD.

Component input source with using the INPUT on the remote control.

to the DVD player's manual for operating instructions.

12

	DIGITAL
	AUDIO
	OUT
HDMI/DVI	(OPTICAL)
	I.

1(DVI)

RJP	VIDEO	AUDIO	S-VIDEO
ERFACE	COMPONENT IN

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV	Y	PB	PR
	Y	PB	PR
Video output ports	Y	B-Y	R-Y
on DVD player	Y	Cb	Cr
	Y	Pb	Pr

18

When connecting with an S-Video cable

1. How to connect

Connect the S-VIDEO output of the DVD to the

1S -VIDEO input on the set.

		AUDIO
S-VIDEO	L	R

2. How to use

on the DVD player, insert a DVD.

AV1 input source with using the INPUT button on remote control.

to AV IN2, select AV2 input source.

12

GITAL
UDIO	RESET
OUT
			S
TICAL)		REMOTE
M.P.I.
	UPDATE	CONTROL
AUDIO	(MONO)	VIDEO	SPE
	AUDIO
NT IN	AV IN 1		O

to the DVD player's manual for operating instructions.

When connecting HDMI cable

1.How to connect

1 Connect the HDMI output of the DVD to the HDMI/DVI IN 1(DVI) or 2 jack on the set.

No separated audio connection is necessary. HDMI supports both audio and video.

2.How to use

HDMI1/DVI or HDMI2 input source with using INPUT button on the remote control.

to the DVD player's manual for operating instructions.

! NOTE

G When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player output resolution will be automatically set to 720p.

G If the device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the DVD to 720p.

				DIGITAL
				AUDIO
				OUT
	HDMI/DVI IN			(OPTICAL)
		1(DVI)	2			M.P.I

RJP	VIDEO	AUDIO
	COMPONENT IN
INTERFACE
	1

HDMI-DVD OUTPUT

SETUP EQUIPMENT EXTERNAL

19

EXTERNAL EQUIPMENT SETUP

VCR SETUP

SETUP EQUIPMENT EXTERNAL

■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon.

When connecting with an antenna

				RGB IN
				(PC)
				AUDIO IN	REMOTE
			HDMI IN	(RGB/DVI)	CONTROL IN
		ANTENNA/	2
		CABLE IN
	1		1			OPTICAL
S-VIDEO VIDEO L
	R			RS-232C IN		DIGITAL AUDIO
							S-VIDEO VIDE
			HDMI/DVI IN	(CONTROL & SERVICE)		OUT
OUTPUT
SWITCH

Wall Jack

2

Antenna

1. How to connect

1 Connect the RF antenna out socket of the VCR to the Antenna socket on the set.

the antenna cable to the RF antenna in socket of the VCR.

2.How to use

■Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

■Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

20

When connecting with a RCA cable	ANT IN S-VIDEO	L R VIDEO
1. How to connect	ANT OUT OUTPUT
	SWITCH

	1	TV and
		Audio Left

=white, and Audio Right = red)

2.How to use

a video tape into the VCR and press PLAY on the

. (Refer to the VCR owner’s manual.)

AV1 input source with using the INPUT button on remote control.

connected to AV IN2, select AV2 input source.

TAL			1
DIO
UT				SERV
CAL)			REMOTE
M.P.I.
				R
AUDIO	S-	(MONO)	VIDEO	SPEAKE
		AUDIO
T IN		AV IN 1		OUT
				8

! NOTE

G If you	a mono VCR, con-
nect the	cable from the
VCR to the AUDIO
L/MON	jack of the set.

When connecting with an S-Video cable
1. How to connect		ANT IN	S	L	R	VIDEO
1	Connect the S-VIDEO output of the VCR to the
	S -VIDEO input on the set.	ANT OUT
	Connect the audio outputs of the VCR to the AUDIO
	input jacks on the set.	GITAL	1	2
		AUDIO		RESET
		OUT
							SE
		PTICAL)				REMOTE
		M.P.I.
2. How to use						CONTROL
						OUT
	a video tape into the VCR and press PLAY on the VCR.
	to the VCR owner’s manual.)	AUDIO	S-VIDEO	(MONO)		VIDEO	SPEA
				AUDIO
		ENT IN		AV IN 1			OU
	AV1 input source with using the INPUT button on						8
	remote control.

to AV IN2, select AV2 input source.

CAUTION

G Do not connect to both Video ! NOTE and S-Video at the same time. In

G The picture quality is improved: compared to normal

the event that you connect both

composite (RCA cable) input.

Video and the S-Video cables, only the S-Video will work.

SETUP EQUIPMENT EXTERNAL

21

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

1. How to connect

1

		Match the jack colors.
		(Video = yellow, Audio Left = white, and
EXTERNAL		Audio Right = red)
EQUIPMENT	2. How to use
		AV2 input source with using the
SETUP		PUT button on the remote control.
		to AV IN1 input, select	AV1

source.

the corresponding external equipment.

Camcorder

Video Game Set

	VIDEO					R

S-VIDEO

1

VIDEO L/MONO AUDIO R

AV IN 2

22

DIGITAL AUDIO OUTPUT

Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.

1. How to connect

Connect one end of an optical cable to the TV Digital

1	Audio (Optical) Output port.			DIGITAL
				AUDIO
				OUT
	end of the optical cable to the	HDMI/DVI IN		(OPTICAL)
		1(DVI)		M.P.I.
	) input on the audio equipment.
				1
	Set the “TV Speaker option - Off” in the AUDIO
	menu. (G p.50). See the external audio equipment		VIDEO	AUDIO	S-V
	instruction manual for operation.	RJP
			COMPONENT IN
		NTERFACE

!	NOTE	2

G When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p.50)

CAUTION

G Do not look into the optical output port. Looking at the laser beam may damage your vision.

SETUP EQUIPMENT EXTERNAL

23