LG 37LC7D, 37LC7D-UB Service Manual

LCD TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LA73E

MODEL : 37LC7D

37LC7D-UB

- 2 -

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ..................................................................................3

SPECIFICATION........................................................................................6

ADJUSTMENT INSTRUCTION................................................................11

TROUBLE SHOOTING & BLOCK DIAGRAM ........................................17

EXPLODED VIEW .................................................................................. 43

REPLACEMENT PARTS LIST ............................................................... 45

SVC. SHEET ...............................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

T e M

IMPORTANT SAFETY NOTICE

0.15uF

o Instrument's xposed

ETALLIC PARTS

AC Volt-meter

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

- 4 -

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500

F to 600 F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500

F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuitboard printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500

F to 600 F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS

- 5 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

- 6 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

4. General Specification(TV)

No. Item Specification Remark

1. Receiving System ATSC/64 & 256 QAM/ NTSC-M

2. Available Channel 1) VHF : 02~13

2) UHF : 14~69

3) DTV : 02-69

4) CATV : 01~135

5) CADTV : 01~135

3. Input Voltage 1) AC 100 ~ 240V 50/60Hz

4. Market NORTH AMERICA

5. Screen Size 26 inch Wide – 26 inches(582.96mm) For 26LC7D-UB 32 inch Wide - 31.51inches(800.4mm) For 32LC7D-UB,32LC4D-UA 37 inch Wide – 32.02 inches(940.3mm) For 37LC7D-UB 42 inch Wide – 42.02 inches(1067.308mm) For 42LC7D-UB,42LC4D-UA

6. Aspect Ratio 16:9

7. Tuning System FS

8. LCD Module T260XW02-V5 For 26LC7D-UE LC320WX4-SLA1 For 32LC7D-UB,32LC4D-UA LC370WX3-SLA1 For 37LC7D-UB LC420WX6-SLA1 For 42LC7D-UB,42LC4D-UA

9. Operating Environment 1) Temp : 0 ~ 40 deg

2) Humidity : ~ 80 %

10. Storage Environment 1) Temp : -20 ~ 60 deg

2) Humidity : 0 ~ 90 %

1. Application Range.

This spec sheet is applied to the 37"/42" LCD TV used LA73E chassis.

2. Especificación

Each part is tested as below without special appointment

2.1 Temperature : 20 ±5°C

2.2 Relative Humidity : 65 ±10%

2.3 Power Voltage : Standard input voltage (100~240V@ 50/60Hz)

• Standard Voltage of each products is marked by models

2.4 Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM .

2.5 The receiver must be operated for about 20 minutes prior to the adjustment.

3. Test method

3.1 Performance : LGE TV test method followed.

3.2 Demanded other specification Safety : UL, CSA, IEC specification

3.3 EMC : FCC, ICES, IEC specification

- 7 -

5. Chroma & Brightness

5-1. 37LC7D-UB

CONDITION : EZ-Picture "Daylight"

5-2. 42LC7D-UB, 42LC4D-UA

CONDITION : EZ-Picture "Daylight"

No Item Min Typ Max Unit Remark

1. White peak brightness 360 450 cd/m

HDMI input, full white, Video Black level=High

2. Contrast ratio 700:1 900:1 Non dimming mode (PC Mode)

3000:1 4000:1 5000:1 Dimming mode

1. Input full black, wait 10 minute

measure black level

2. Input full white , wait 10 minute, measure white level

3. Brightness uniformity 1.3 Refer to LCD SPEC.

4. Color coordinate RED X 0.633 +/- 0.03

Y 0.339 +/- 0.03

GREEN X 0.286 +/- 0.03

Y 0.610 +/- 0.03

BLUE X 0.147 +/- 0.03

Y 0.065 +/- 0.03

WHITE X 0.276 +/- 0.03

Y 0.283 +/- 0.03

5. Viewing angle 178 R/L, U/D

6. Color Temperature Standard 8,300 9,300 10,300 <Test Signal>

Cool 10,000 11,000 12,000

HDMI input, With 16-gray pattern

Warm 5,500 6,500 7,500 6thbar from right

No Item Min Typ Max Unit Remark

1. White peak brightness 360 450 cd/m

HDMI input, full white, Video Black level=High

2. Contrast ratio 800:1 1000:1 Non dimming mode (PC Mode)

3000:1 4000:1 5000:1 Dimming mode

1. Input full black, wait 10 minute

measure black level

2. Input full white , wait 10 minute, measure white level

3. Brightness uniformity 1.3 Refer to LCD SPEC.

4. Color coordinate RED X 0.633 +/- 0.03

Y 0.339 +/- 0.03

GREEN X 0.286 +/- 0.03

Y 0.610 +/- 0.03

BLUE X 0.147 +/- 0.03

Y 0.065 +/- 0.03

WHITE X 0.276 +/- 0.03

Y 0.283 +/- 0.03

5. Viewing angle 178 R/L, U/D

6. Color Temperature Standard 8,300 9,300 10,300 <Test Signal>

Cool 10,000 11,000 12,000 HDMI input,

Warm 5,500 6,500 7,500 Daylight/Cool 85 IRE

- 8 -

6. Component Video Input (Y, PB

, PR)

No.

Specification

Remark

Resolution H-freq(kHz) V-freq(Hz)

1. 720*480 15.73 59.94 SDTV ,DVD 480I

2. 720*480 15.73 60.00 SDTV ,DVD 480I

3. 720*480 31.47 59.94 SDTV 480P

4. 720*480 31.50 60.00 SDTV 480P

5. 1280*720 44.96 59.94 HDTV 720P

6. 1280*720 45.00 60.00 HDTV 720P

7. 1920*1080 33.72 59.94 HDTV 1080I

8. 1920*1080 33.75 60.00 HDTV 1080I

9. 1920*1080 27 24 HDTV 1080P

10. 1920*1080 33.75 30 HDTV 1080P

No.

Specification

Remark

Resolution H-freq(kHz) V-freq(Hz)

Pixel clock(MHz)

PC DDC

1. 640*350 31.469 70.08 25.17 DOS

2. 720*400 31.469 70.08 28.32 DOS O

3. 640*480 31.469 59.94 25.17 VESA(VGA) O

4. 800*600 37.879 60.31 40.00 VESA(SVGA) O

5. 1024*768 48.363 60.00 65.00 VESA(XGA) O

6. 1280*768 47.776 59.87 79.50 CVT(WXGA) O

7. 1360*768 47.720 59.799 84.75 CVT(WXGA) O

8. 1366*768 47.13 59.65 72

7. RGB PC

- RGB PC INPUT Mode Table

- HDMI INPUT(PC/DTV)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark

PC DDC

1. 640*480 31.469 59.94 25.17 VESA(VGA) O

2. 800*600 37.879 60.31 40.00 VESA(SVGA) O

3. 1024*768 48.363 60.00 65.00 VESA(XGA) O

4. 1280*768 47.776 59.87 79.50 CVT(WXGA) O

5. 1360*768 47.720 59.799 84.75 CVT(WXGA) O

6. 1366*768 47.13 59.65 72

DTV

7. 720*480 31.469 59.94 27.00 SDTV 480P

8. 720*480 31.500 60.00 27.03 SDTV 480P

9. 1280*720 44.96 59.94 74.17 HDTV 720P

10. 1280*720 45.00 60.00 74.25 HDTV 720P

11. 1920*1080 33.72 59.94 74.17 HDTV 1080I

12. 1920*1080 33.75 60.00 74.25 HDTV 1080I

13. 1920*1080 27 24.00 74.25 HDTV 1080P

14. 1920*1080 33.75 30.00 74.25 HDTV 1080P

- 9 -

8. Mechanical specification

1) 37LC7D

No. Item Content Unit Remark

1. Product Widt(W) Length(D) Height(H) mm

Dimension Before Packing 927 280.5 692.8 mm With Stant

After Packing 999 264 874 mm

2. Product Only SET 20 Kg

With BOX 25 Kg

2) 42LC7D

No. Item Content Unit Remark

1. Product Widt(W) Length(D) Height(H) mm

Dimension Before Packing 1033.4 287.6 750 mm With Stant

After Packing 1119 374 858 mm

2. Product Only SET 24.9 Kg

With BOX 30.4 Kg

- 10 -

9. Customer Menu Setup (Shipment Condition)

No Item Condition Remark

1. Input Mode TV02CH

2. Volume Level 30

3. Mute Off

4. Aspect Ratio 16:9

5. Video EZ Picture Daylight

Contrast 100 Brightness 40 Color 70 Sharpness 70 Tint 0 Color-temperature Cool XD Auto(On) Advanced Cinema3:2 Mode(Off)

Black Level(RF,HDMI=>Low),(AV=>High)( RGB-PC,Component=>Disable)

6. Audio Audio Language Off

EZ Sound Normal Balance 0 Bass 50 Front Surround Off TV Speaker On

7. Timer Auto clock Off

Manual Clock Off Off Timer Off On Timer Off Sleep Timer Off Auto Off Off

8. Option Aspect Ratio 16:9

Caption/Text Off Caption Option Set By Program Language English Simplink On

9. Lock Lock System Off

Set password On

(Default:0000) Block channel None Movie Rating Off TV Rating-Children None TV Rating-General None Input Block Off

10. Channel Memory RF : 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 30, 51, 63 CATV : 15, 16, 17

- 11 -

ADJUSTMENT INSTRUCTION

1. Application Object

These instructions are applied to all of the LCD TV, LA73E.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test equipment. (2) Adjustments must be done in the correct order. (3) The adjustments must be performed in the circumstance of

20±5°C of temperature and 65±10% of relative humidity if

there is no specific designation. (4) The input voltage of the receiver be must kept 110V, 60Hz

when adjusting. (5) The receiver must be operational for about 15 minutes

prior to the adjustments.

Perform preliminary operation after receiving 100% White

Pattern (06CH).

(Or 3. White Pattern status of Ez-Adjust)

White Pattern entry method

A) Enter into Ez-Adjust by pressing the ADJ key on the

adjustment R/C.

B) 100% FULL WHITE PATTERN appears if pressing the

OK (

) key after selecting the 3.WHITE PATTERN with

the CH + / - KEY.

* It is possible to heat run the set without a separate signal generator in this mode.

Caution : Care must be taken as afterimage phenomena may occur about the black level part of screen If leaving pause image turned on for more than 20 minutes (especially inner digital pattern (13 CH), Cross Hatch Pattern (09CH) with significant black/white contrast).

3. MICOM Download(Option)

3-1. Required Test Equipment

(1) JIG-LEVER TYPE for adjusting: 1EA (2) PC & MONITOR: 2EA (3) BOARD for INTERFACE: IIC & ISP BOARD: 2EA (4) 15P D-SUB CABLE: 2EA (5) Using the 12/15 line of D-SUB 15P

12-SDA/15-SCL

3-2. JIG Connection

3-3. Establishment Program

(1) Establish LGE Monitor Tools v1.1 (2) The program work and it is opened program window as

seen below.

connection

to PC

connection

to PC

- 12 -

(3) Click the first icon shown in fig.9. The window seen in

fig.10 should appear.

3-4. Set Method

(1) MCU Select: MTV512M64 (2) Option

R/W Option: Auto Write(Verity)

Jig Option: Myson

Transmit Speed: Medium

(3) Check: Just do it with blank micom. (4) PORT

Chose Parallel Port (normal LPT1)

Attention: You must chose EPP when select Rom BIAS at

LPT

3-5. Download Method

(1) Click the Load File.

(2) Locate and select the correct file from your computer.

(*.hex).

(3) Click the Send.

(4) When you see (ISP COMPLETE) the download is

complete.

- 13 -

6. ADC-Set Adjustment

6-1. Synopsis

ADC-Set adjustment to set the black level and the Gain to optimum.

6-2. Test Equipment

Service R/C, 801GF(802V, 802F, 802R) or MSPG925FA Pattern Generator (480i/1080i The Horizontal 100% Color Bar Pattern adjust to within 0.7±0.1Vp-p)

[ADC adjustment (MSPG-925Fx series) Model No. & Pattern No.]

- Model No.: #209(480i adjustment), #223(1080i adjustment)

- Pattern No.: #65(7ColorBar Pattern)

6-3. Adjustment

(1) Select Component1 as the input with 100% Horizontal

Color Bar Pattern(HozTV31Bar) in 480i Mode

(2) After receiving signal for at least 1 second, press the ADJ

Key on the Service R/C to enter the ‘Ez - Adjust’ and select the ‘2. ADC 480i Comp1’.

Pressing the Enter Key to adjust automatically.

(3) When the adjustment is over, 'MST3361 Component

Success’ is displayed. If the adjustment has errors, 'MST3361 Configuration Error’ is displayed.

(4) Select Component1 as the input with 100% Horizontal

Color Bar Pattern(HozTV31Bar) in 1080i Mode.

(5) After receiving signal for at least 1 second, press the ADJ

Key on the Service R/C to enter the ‘Ez - Adjust’ and select the ‘3. ADC 1080i Comp1/RGB’. Pressing the Enter Key to adjust automatically.

(6) When the adjustment is over, 'MST3361 Component

Success’ is displayed. If the adjustment has errors, 'MST3361 Configuration Error’ is displayed.

(7) After the Component MST3361 adjustment is over, convert

the RGB-DTV Mode and display Pattern. When the adjustment is over, 'MST3361 RGB_DTV Success’ is displayed.

(8) Readjust after confirming the case Pattern or adjustment

condition where the adjustment errors.

(9) After adjustment is complete, exit the adjustment mode by

pressing the ADJ KEY.

<Fig. 2> Adjustment Mode

<Fig. 3> Adjustment Pattern: 480i/1080i 60Hz HozTV30 Bar

Pattern

- 14 -

7. EDID(The Extended Display

Identification Data)/DDC (Display Data Channel) Download

This is the function that enables “Plug and Play".

7-1. HDMI EDID Data Input

(1) Required Test Equipment

1) PC, Jig for adjusting DDC. (PC serial to D-sub Connection equipment)

2) S/W for writing DDC(EDID data write & read)

3) D-Sub cable

4) Jig for HDMI Cable connection

(2) Preparation for Adjustments &

Setting of Device

1) Set devices as below and turn on the PC and JIG.

2) Open S/W for writing DDC (EDID data write & read). (operated in DOS mode)

7-2. EDID DATA for LA73E

:EDID for HDMI-1 (DDC (Display Data Channel) Data)

EDID Block 0 table =

EDID Block 1 table =

:EDID for HDMI-2 (DDC (Display Data Channel) Data)

EDID Block 0 table =

EDID Block 1 table =

:EDID for RGB-PC

EDID Block 0 table =

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 | 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23 20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01

30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70 40 | 36 00 C4 8E 21 00 00 1E 0E 1F 00 80 51 00 1E 30 50 | 40 80 37 00 C4 8E 21 00 00 1C 00 00 00 FD 00 38 60 | 4B 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC

70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98

0 | 02 03 16 F1 46 84 05 03 02 20 22 23 15 07 50 66 10 | 03 0C 00 10 00 80 01 1D 00 72 51 D0 1E 20 6E 28 20 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20

30 | 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0 40 | 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A

50 | 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 00 00

60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 25

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 | 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23

20 | 09 48 4C 2F CE 00 31 40 45 40 61 40 01 01 01 01 30 | 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28 40 | 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20

50 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 FC 00 4C

60 | 47 20 54 56 0A 20 20 20 20 20 20 20 00 00 00 FD

70 | 00 38 4B 1F 3C 09 00 0A 20 20 20 20 20 20 01 66

0 | 02 03 16 F1 46 84 05 03 02 20 22 23 15 07 50 66 10 | 03 0C 00 20 00 80 8C 0A D0 8A 20 E0 2D 10 10 3E 20 | 96 00 C4 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10

30 | 10 3E 96 00 13 8E 21 00 00 18 00 00 00 00 00 00

40 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B3

0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01

10 | 00 11 01 03 68 73 41 96 0A CF 30 A3 57 4C B0 23

20 | 09 50 4E A1 08 00 01 01 01 01 01 01 01 01 01 01

70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 D0

LCD TV SET

(or Digital Board)

+ 32 hidden pages