LG 34WN80C User Manual

* LG LED Monitor applies LCD screen with LED backlights.

Please read this manual carefully before operating your set and retain it for future reference.

34WN80C

OWNER’S MANUAL

LED LCD MONITOR

(LED Monitor*)

www.lg.com

TABLE OF CONTENTS

ENGLISH

LICENSE ...................................................... 2

LICENSE

Each model has different licenses. Visit www.lg.com for more information on the license.

ASSEMBLING AND PREPARING .................. 3

USING THE MONITOR .................................. 8

USER SETTINGS ........................................ 10

TROUBLESHOOTING .................................21

PRODUCT SPECIFICATION ......................... 23

USB Type-C

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

The SuperSpeed USB Trident logo is a registered trademark of USB Implementers Forum, Inc.

and USB-C TM are trademarks of USB Implementers Forum.

ASSEMBLING AND PREPARING

CAUTION

• Always use genuine LG components to ensure safety and product per formance.

• The product warranty will not cover damage or injury caused by the use of unauthorized components.

• It is recommended that use the supplied components.

• If you use generic cables not certified by LG, the screen may not display or there may be image noises.

• Illustrations in this document represent typical procedures, so they may look different from the actual product.

• Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing

so may damage the product.)

• Applying excessive force when tightening screws may cause damage to the monitor. Damage caused in this

way will not be covered by the product warranty.

• Do not carry the monitor upside down by just holding the base. This may cause the monitor to fall off the stand

and could result in personal injury.

• When lifting or moving the monitor, do not touch the monitor screen. The force applied to the monitor screen

may cause damage to it.

NOTE

• The components may look different from those illustrated here.

• Without prior notice, all product information and specifications contained in this manual are subject to change

to improve the performance of the product.

• To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailer

from which you purchased the product.

• The power cord provided may differ depending upon the region.

Supported Drivers and Software

You can download and install the latest version from the LGE website (

Drivers and Software Installation Priority

Monitor Driver Recommended

OnScreen Control Recommended

Dual Controller Optional

www.lg.com

ENGLISH

Product and Button Description

ENGLISH

Joystick Button

How to Use the Joystick Button

You can easily control the functions of the monitor by pressing the joystick button or moving it left/right/up/ down with your finger.

Basic Functions

Moving and Lifting the Monitor

When moving or lifting the monitor, follow these instructions to prevent the monitor from being scratched or damaged and to ensure safe transportation, regardless of its shape or size.

• Place the monitor in the original box or packing material before attempting to move it.

• Before moving or lifting the monitor, disconnect the power cord and all other cables.

• Hold the bottom and side of the monitor frame firmly. Do not hold the panel itself.

• When holding the monitor, the screen should face away from you to prevent it from being scratched.

• When transporting the monitor, do not expose the monitor to shock or excessive vibration.

• When moving the monitor, keep it upright and never turn the monitor on its side or tilt it sideways.

/ Volume control

NOTE

• The joystick button is located at the bottom of the monitor.

Power on

Power off

Press the joystick button once with your finger to turn on the monitor.

Press and hold the joystick button once more than 5 seconds with your finger to turn off the monitor.

You can control the volume by moving the joystick button left/right.

CAUTION

• Avoid touching the monitor screen as much as possible.

- This may result in damage to the screen or some of the pixels used to create images.

• If you use the monitor panel without the stand base, its joystick button may cause the monitor to become

unstable and fall, resulting in damage to the monitor or human injury. In addition, this may cause the joystick button to malfunction.

Installing on a Table

• Lift the monitor and place it on the table in an upright position. Place the monitor at least 100mm (3.94

inches) away from the wall to ensure sufficient ventilation.

Adjusting the Stand Height

1 Place the monitor mounted on the stand base in an upright position. 2 Handle the monitor with both hands for safety.

ENGLISH

100 mm (3.94 inches)

CAUTION

• Unplug the power cord before moving or installing the monitor. There is risk of electric shock.

• Make sure to use the power cord that is provided in the product package and connect it to a grounded power

outlet.

• If you need another power cord, please contact your local dealer or the nearest retail store.

100 mm (3.94 inches)

Max. 110.0 mm (4.3 inches)

WARNING

• When adjusting the screen height, do not place your hand on the stand body to avoid injur y to your fingers.

Adjusting the Angle

1 Place the monitor mounted on the stand base in an upright position. 2 Adjust the angle of the screen.

The angle of the screen can be adjusted forward or backward from -5° to 15° for a comfor table viewing experience.

WARNING

• To avoid injur y to the fingers when adjusting the screen, do not hold the lower part of the monitor’s frame as

illustrated below.

• Be careful not to touch or press the screen area when adjusting the angle of the monitor.

Using the Kensington Lock

The connector for the Kensington security system is located at the bottom of the monitor. For more information on installation and usage, refer to the Kensington lock owner’s manual or visit the website

at http://www.kensington.com.

ENGLISH

Connect the monitor to a table using the Kensington security system cable.

NOTE

• The Kensington security system is optional. You can obtain optional accessories from most electronics stores.

Installing the Wall Mount Plate

This monitor meets the specifications for the wall mount plate or other compatible devices.

NOTE

• The wall mount plate is sold separately.

• For more information on installation, refer to the wall mount plate’s installation guide.

• Be careful not to apply too much force while mounting the wall mount plate as it may cause damage to the

screen.

• Remove the stand before installing the monitor on a wall mount by performing the stand attachment in

reverse.

Installing on the Wall

Install the monitor at least 100mm (3.94 inches) away from the wall and leave about 100mm (3.94 inches) of space at each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local retail store. Alternatively, please refer to the manual for how to install and set up a tilting wall mounting bracket.

100 mm (3.94 inches)

To install the monitor to a wall, attach a wall mounting bracket (optional) to the back of the monitor. Make sure that the wall mounting bracket is securely fixed to the monitor and to the wall.

Wall Mount (mm) 100 x 100

Standard screw M4 x L10

Number of screws 4

Wall Mount Plate (Optional) LSW 149

NOTE

• A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not liable

for any accidents relating to the use of non-standard screws.

• The wall mount kit includes the installation guide and all necessary parts.

• The wall mounting bracket is optional. You can obtain optional accessories from your local dealer.

• The length of the screw may differ for each wall mounting bracket. If you use screws longer than the standard

length, it may damage the inside of the product.

• For more information, please refer to the user manual for the wall mounting bracket.

CAUTION

• Unplug the power cord before moving or installing the monitor to avoid electric shock.

• Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could lead

to injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.

• Applying excessive force when tightening screws may cause damage to the monitor. Damage caused in this

way will not be covered by the product warranty.

• Use the wall mounting bracket and screws that conform to VESA standards. Damage caused by the use or

misuse of inappropriate components will not be covered by the product warranty.

• When measured from the back of the monitor, the length of each installed screw must be 8 mm (0.3 inches)

or less.

Wall Mount Plate

Back of the Monitor

Wall Mount Plate

Back of the Monitor

Standard screw:

M4 x L10

Max. 8 mm (0.3 inches)

ENGLISH

USING THE MONITOR

• Illustrations in this manual may differ from the actual product.

ENGLISH

Press the joystick button, go to Settings

CAUTION

• Do not press the screen for a prolonged time. This may cause image distortion.

• Do not display a still image on the screen for a prolonged time. This may cause image retention. Use a PC

screensaver if possible.

• When connecting the power cord to the outlet, use a grounded (3-hole) power strip or a grounded power

outlet.

• The monitor may flicker when turned on in an area where the temperature is low. This is normal.

• Sometimes red, green, or blue spots may appear on the screen. This is normal.

Connecting to a PC

• This monitor supports the *Plug and Play feature.

* Plug and Play: A feature that allows you to add a device to your computer without having to reconfigure

anything or install any manual drivers.

HDMI Connection

Transmits digital video and audio signals from your PC to the monitor.

CAUTION

• Using a DVI to HDMI / DP (DisplayPort) to HDMI cable may cause compatibility issues.

• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not

display or a connection error may occur.

• Recommended HDMI cable types

- High-Speed HDMI

®/TM

cable

®/TM

cable with Ethernet

Input, and then select the input option.

DisplayPort Connection

Transmits digital video and audio signals from your PC to the monitor.

NOTE

• There may be no video or audio output depending on the DP (DisplayPort) version of the PC.

• Make sure to use the supplied DisplayPort cable of the product. Otherwise, this may cause the device to

malfunction.

• If you are using a Mini DisplayPort output graphics card, use a Mini DP to DP (Mini DisplayPort to DisplayPort)

cable or gender that supports DisplayPort1.4. (Sold separately)

USB-C connection

Transmits digital video and audio signals and USB data from your PC to the monitor. Connect the monitor to your PC using the USB-C cable as shown in the illustration below. Press the menu button and then select the input option from the input menu.

NOTE

• PD (Power Delivery), DP Alternate Mode (DP over USB-C) and USB Data are supported via USB-C Por t.

• Features may not work properly depending on the connected device’s specifications and the environment.

• USB-C port is not for the Monitor Power source but for a PC power source.

Connect Adapter to supply power to the Monitor.

+ 18 hidden pages