LG LA53A, 32LP2DC-UA Service Manual
LCD TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : LA53A
MODEL : 32LP2DC-UA
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
- 2 -
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ..................................................................................3
SPECIFICATION........................................................................................6
ADJUSTMENT INSTRUCTION ...............................................................12
TROUBLE SHOOTING............................................................................15
BLOCK DIAGRAM...................................................................................18
WIRING DIAGRAM..................................................................................21
EXPLODED VIEW .................................................................................. 22
EXPLODED VIEW PARTS LIST..............................................................23
REPLACEMENT PARTS LIST ............................................................... 24
SVC. SHEET ...............................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
X-RAY Radiation
Warning:
To determine the presence of high voltage, use an accurate high
impedance HV meter.
Adjust brightness, color, contrast controls to minimum.
Measure the high voltage.
The meter reading should indicate
23.5
1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch,
29.0
1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and
correction is required to prevent the possibility of premature
component failure.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
The source of X-RAY RADIATION in this TV receiver is the High
Voltage Section and the LCD PANEL.
For continued X-RAY RADIATION protection, the replacement
panel must be the same type panel as specified in the
Replacement Parts List.
IMPORTANT SAFETY NOTICE
0.15uF
To Instrument's
exposed
METALLIC PARTS
AC Volt-meter
1.5 Kohm/10W
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
- 4 -
CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500
F to 600 F.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500
F to 600 F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500
F to 600 F)
b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
SERVICING PRECAUTIONS
- 5 -
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
- 6 -
1. Application range
This specification is applied to LA53A chassis.
2. Specification
Each part is tested as below without special appointment.
(1) Temperature: 20°C ± 5°C
(2) Humidity: 65% ± 10%
(3) Power: Standard input voltage (AC 100-240V, 50/60Hz)
* Standard Voltage of each product is marked by models.
(4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM
(5) The receiver must be operated for about 20 minutes prior
to the adjustment.
3. Test method
(1) Performance : LGE TV test method followed
(2) Demanded other specification
Safety : UL, CSA, IEC specification
(3) EMC : FCC, ICES, IEC specification
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement
.
4. General Specification
No Item Specification Remark
1. Receiving System ATSC/ 64 & 256 QAM/NTSC-M Slim-VSB
2. Available Channel VHF : 02~13
UHF : 14~69
CATV : 01~135
DTV : 02-69
CADTV : 01~135
3. Input Voltage AC 100 ~ 260V 50/60Hz
4. Market North America
5. Screen Size 32 inch wide
6. Aspect Ratio 16:9
7. Tuning System FS
8. LCD Module LC320W01-SL11 (1366x768) LG Philips LCD
9. Operating Environment Temp. : 0 ~ 40 deg
Humidity : ~ 80 %
10. Storage Environment Temp. : -20 ~ 50 deg
Humidity : 10 ~ 90 %
5. Feature and Function
No Item Specification Remark
1. Feature AV Input / Out 2 AV Input1, 2(Video, Front Video) Rear1, Front1
RGB Input 2 Analog RGB1, 2 Rear2(D-Sub 15pin)
S-Input 2 S-Input Rear1, Front1
DVI Input 1 DVI Input Rear1
Y, Pb, Pr Input 2 Component 1, 2 Rear1, Side1
SPDIF Out 1 SPDIF Out Rear
SPDIF Input 1 SPDIF Input Rear
RS-232C 1 S/W Download D-Sub 9pin
Internal SPK Out 1 Mono, < 2W Rear, for remote speaker
2. Key Local Key POWER, TV/Video, Menu, ENTER,
Volume(
, ), Channel ( , )
- 7 -
No Item Specification Remark
3. SETUP EZ Scan Auto Channel Search
Manual Scan TV/CATV/DTV/CADTV
CH. Edit CH. Add/Delete
DTV Signal Bad/Normal/Good DTV Only
Ch. Label Broadcaster Logo RGB-DTV <-> RGB-PC
Main Input Antenna, Cable, Video, Front Video, Component1,
RGB-DTV/PC, DVI
Input Label VCR, DVD, VCR/DVD, Set Top Box, Satellite, Cable Box,
Game, PC for Video, Front Video, Component1/2, RGB, DVI
SET ID 1~99
4. Picture EZ Picture Custom, Daylight, Normal, Night Time,
Movie, Video Game, Sports
Contrast 0~100
Brightness 0~100
Color 0~100
Sharpness 0~100
Tint Red 0~50, Green0~50
Color Temperature Cool/Medium/Warm
Video Preset Initialization
5. Audio Audio Language English/Spanish/French DTV Only
EZ SoundRite Off/On
EZ Sound Custom/Normal/Stadium/News/Music/Theater
Balance Left 0~50, Right 0~50
Treble 0~100
Bass 0~100
Front Surround Off/3D EchoSound System/SRS TruSurround XT
BBE Off/On
TV Speaker Off/On
6. Time Auto Clock Off/On/Time Zone/Daylight Saving
Manual Clock Year/Data/Time
Off Timer Off/On/Time
On Timer Off/On/Time/Ch./Vol
Sleep Timer
Off/10min/20min/30min/60min/90min/120min/180min/240min
Auto Off Off/On
7. Option Aspect Ratio Set By Program/4:3/16:9/Horizon/Zoom1/ DTV : Excluded spectacle
Zoom2/Cinema Zoom
Cinema 3:2 mode Off/On Component 480i, Composite
Caption Off/On
Caption/Text CC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4
Caption Option Style/Size/Font/Text Color/Text Opacity/
Bg Color/Bg Opacity/Edge Type/Edge Color
Language English/Espanol/Francais
8. Lock Lock System Off/On
Set Password New/Confirm Default : 0000
Block Ch. Select
Movie Rating G/PG/PG-13/R/NC-17/X
TV Rating-Children Age/Fantasy Violence
TV Rating-General Age/Dialogue/Language/Sex/Violence
Input Block Video, Front Video, Component1, RGB, DVI
9. Etc. Comb Filter 3D Comb
Remocon LG code
HDCP O
- 8 -
7. External Input Format
7-1. Component Video Input (Y, CB/PB, CR/PR)
7-2. RGB Iinput (PC/DTV)
No Resolution H-freq(kHz) V-freq.(kHz) Pixel clock Proposed
1. 720*480 15.73 59.94 SDTV ,DVD 480I
2. 720*480 15.73 60.00 SDTV ,DVD 480I
3. 720*480 31.47 59.94 SDTV 480P
4. 720*480 31.50 60.00 SDTV 480P
5. 1280*720 44.96 59.94 HDTV 720P
6. 1280*720 45.00 60.00 HDTV 720P
7. 1920*1080 33.72 59.94 HDTV 1080I
8 1920*1080 33.75 60.00 HDTV 1080I
No Resolution H-freq(kHz) V-freq.(kHz) Pixel clock Proposed
PC DDC
1 640*350 31.469 70.08 25.17 DOS X
2 640*480 31.469 59.94 25.17 VESA(VGA) O
3 640*480 37.861 72.80 31.50 VESA(VGA) O
4 640*480 37.500 75.00 31.50 VESA(VGA) O
5 800*600 35.156 56.25 36.00 VESA(SVGA) O
6 800*600 37.879 60.31 40.00 VESA(SVGA) O
7 800*600 48.077 72.18 50.00 VESA(SVGA) O
8 800*600 46.875 75.00 49.50 VESA(SVGA) O
9 1024*768 48.363 60.00 65.00 VESA(XGA) O
10 1024*768 56.476 70.06 75.00 VESA(XGA) O
11 1024*768 60.023 75.02 78.75 VESA(XGA) O
DTV
1. 720*480 31.50 59.94 SDTV 480P
2. 720*480 31.47 60.00 SDTV 480P
3. 1280*720 44.96 59.94 HDTV 720P
4. 1280*720 45.00 60.00 HDTV 720P
5. 1920*1080 33.72 59.94 HDTV 1080I
6. 1920*1080 33.75 60.00 HDTV 1080I
6. Chroma & Brightness
No. Item Min Typ Max Unit Remark
1 White Brightness 400 500 cd/m
2
EZ Picture : Daylight, Color Temperature : Medium
2 Color Coordinate RED X 0.602 0.632 0.662 Full Signal Swing
(Default) Y 0.312 0.342 0.372 ±0.025
GREEN X 0.258 0.288 0.318
Y 0.580 0.610 0.640
BLUE X 0.117 0.147 0.177
Y 0.035 0.065 0.095
WHITE X 0.246 0.287 0.296
Y 0.254 0.289 0.304
3 Brightness uniformity 80 % Full White
4 Contrast ratio 600:1 800:1
EZ Picture : Daylight, Color Temperature : Medium
5 Color Temperature Standard 8,300 9,300 10,300
Cool 11,000 12,000 13,000
Warm 5,500 6,500 7,500
- 9 -
DVI Iinput (PC/DTV)
No Resolution H-freq(kHz) V-freq.(kHz) Pixel clock Proposed
PC DDC
1. 640*480 31.469 59.94 25.17 VESA(VGA) O
2. 640*480 37.861 72.80 31.50 VESA(VGA) O
3. 640*480 37.500 75.00 31.50 VESA(VGA) O
4. 800*600 35.156 56.25 36.00 VESA(SVGA) O
5. 800*600 37.879 60.31 40.00 VESA(SVGA) O
6. 800*600 48.077 72.18 50.00 VESA(SVGA) O
7. 800*600 46.875 75.00 49.50 VESA(SVGA) O
8. 1024*768 48.363 60.00 65.00 VESA(XGA) O
9. 1024*768 56.476 70.06 75.00 VESA(XGA) O
10. 1024*768 60.023 75.02 78.75 O
DTV
11. 720*480 31.500 59.94 27.00 SDTV 480P
12. 720*480 31.469 60.00 27.03 SDTV 480P
13. 1280*720 44.96 59.94 HDTV 720P
14. 1280*720 45.00 60.00 HDTV 720P
15. 1920*1080 33.72 59.94 HDTV 1080I
16. 1920*1080 33.75 60.00 HDTV 1080I
8. POWER
No Item Min Typ Max Unit Remark
1. AC Power Operating Voltage 100 240 V
2. DC Voltage, LCD Panel Drive 11.4 12.0 12.6 V
3. DC Voltage, Inverter 22.8 24.0 25.2 V
4. DC Voltage, Sound AMP 18.0 19.0 20.0 V
5. DC Voltage, Stand By 5.6 6.0 6.4 V
6. DC Voltage, Scaler(HD2) 3.1 3.3 3.5 V I/O port supply
7. DC Voltage, Scaler(HD2) 1.6 1.8 1.9 Internal core supply
8. DC Voltage, ADC 3.0 3.3 3.6 V MST3385
DC Voltage, ADC 2.5V 2.3 2.5 2.7 V
9. DC Voltage, Micom 4.7 5 5.3 V
10. DC Voltage, Tuner 4.75 5.00 5.25 V
- 10 -
9. External Interface
- AV Input
No Item Min Typ Max Unit Remark
1. AV Video Out Level 0.85 1.0 1.15 Vpp
2. AV Video Sync Out Level 0.24 0.29 0.32 Vpp
3. AV Burst Out Level 0.14 0.28 0.35 Vpp
4. AV Video Out Frequency Characteristic 3.0 MHz
5. AV Video Out S/N 40.0 dB
6. AV Audio In S/N, L/R 43.0 dB
7. AV Audio In Frequency Response, Low 80.0 Hz
8. AV Audio In Frequency Response, High 7.0 10.0 18.0 kHz
9. AV Audio In Distortion 2.0 %
10. AV Audio In Max Distortion 10.0 %
11. AV Audio In Level, L/R 0.3 0.4 0.5 Vrms
12. AV Audio In Crosstalk, L/R 40.0 dB
13. AV Audio Dynamic Range 2.00 Vpp
14. AV Audio Out Level, L/R 0.3 0.4 0.5 Vrms
15. AV Audio Out Crosstalk, L/R 20.0 dB
16. AV Audio Out S/N, L/R 43.0 dB
17. AV Audio Out Distortion 2.0 %
18. AV Audio Out Frequency Response Low 80.0 Hz
High 8.0 10.0 19.0 kHz
19. Component Video Input Level (Y, CB/PB, CR/PR) 0.6 1.0 1.14 Vpp 75 ohm
(480i,480p,720p,1080i)
20. RGB Input Level 0.6 0.7 0.8 Vpp 75 ohm
10. General Specifications
No Item Min Typ Max Unit Remark
1 Active Screen Size 750.062(diagonal) mm 29.53 inches
2 Outline Dimension 697.3(H)x431.8(V)x50.9(D) mm
3 Pixel Pitch 0.5025x0.1675xRGB mm
4 Pixel Format 1280(H)x768(V) stripe arrangement
5 Color Depth 8bit 16.7 Mbit
6 Luminance ,White 500 (center 1 point typ) cd/m2
7 Viewing Angle (CR>10) R/L 176(Typ),U/P 176(Typ) degree
8 Power Consumption 99.16 Watt
9 Weight 6.75 kg
10 Display Operating Mode Transmissive mode ,normally black
11 Surface Treatment Hard coating (3H)
12 Altitude Operating 0 - 14,000 feet 4,267.2 m
Storage/Shipment 0 - 40,000 feet 12,192.0 m
- 11 -
11. Electro Optical Characteristic Specifications
No Item Min Typ Max Unit Remark
1 Contrast Ratio 600 800 C It measured at center point
2 Surface Luminance, White 400 500 Cd/m
2
Full white
3 Luminance Variation 1.3
4 Response Time Tr (Rising time) 16 30 msec
5 Color coordinate RED X 0.632 Full Pattern
Y 0.342
GREEN X Typ 0.288 Typ
Y -0.03 0.610 +0.03
BLUE X 0.147
Y 0.065
WHITE X 0.287
Y 0.289
6 Viewing Angle X axis right(
=0) 85 88 degree
(CR>10) X axis left(
=180) 85 88
Yaxis up (
=90) 85 88
Z axis down(
=270) 85 88
12. Mechanical specification
No Item Content Remark
1
Product
Width (W) Length (D) Height (H)
Dimension
874 109 538
874 186 580.5 With Stand
2 Product Weight 28.1Kg
- 12 -
1. Application Object
This instruction is for the application to the LCD TV.
2. Designation.
2.1 As this chassis is a non-charging type of chassis for
insulation of the power supply part, it may not use an
insulation type of transformer but it is better to adjust after
operating an insulation type of transformer between the
power supply line and the input side of chassis.
2.2 Adjustment must be done according to accurate order.
However, order may be changed considering mass
production.
2.3 Adjustment must be done in environment of ambient
temperature of 25
5°C, RH 65 10% unless specially
designated.
2.4 For adjustment, input voltage of the receiver must be
maintained at 110V, 60Hz.
2.5 The receiver must be maintained in preliminary operation
status for about 15 minutes before adjustment unless
specially designated.
Perform preliminary operation after receiving 100%
White Pattern (06CH).
(Or 3. White Pattern status of Ex-Adjust)
White Pattern entry method
A) Enter into Ez-Adjust by pressing the ADJ key on
the adjustment R/C.
B) 100% FULL WHITE PATTERN appears if pressing
the OK (
) key after selecting the 3.WHITE
PATTERN with the CH + / - KEY.
* It is possible to heat run the set without a separate
signal generator in this mode.
Caution : Care must be taken as afterimage phenomena
may occur about the black level part of screen If leaving
pause image turned on for more than 20 minutes
(especially inner digital pattern (13 CH), Cross Hatch
Pattern (09CH) with significant black/white contrast).
3. Total Adjustment
3.1 EDID (Extended Display Identification Data ) / DDC
(Display Data Channel) download
3.1.1 Summary
: This function was created by VESA and is intended to
realize "Plug and Play" that the computer automatically
communicates with the monitor through mutual change of
information and re-configure user environment so than the
user can immediately use the computer without providing
direct command to the PC or monitor.
3.2 AD9883A-Set Adjustment
3.2.1 Summary
: The AD9883A-Set Adjust is function that the A/D
converter automatically sets up optimum blacklevel and
gain and compensate RGB deviation.
- DVI EDID Data
- RGB EDID Data
ADJUSTMENT INSTRUCTION
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 03 0E 01 03 98 6E 3E 96 08 E8 AA A1 57 49 9C 25
20 10 48 4B AF CE 00 31 4A 31 4F 3B C0 45 40 61 4F
30 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 13 00 4C 6C 42 00 00 1E 00 00 00 FC 00 4C 47 20
50 4C 43 44 20 20 20 20 20 20 0A 00 00 00 FD 00 38
60 4B 1E 3E 08 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 33 32 4C 50 31 44 43 20 20 20 20 20 20 00 BE
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 03 0E 01 03 18 6E 3E 96 08 E8 AA A1 57 49 9C 25
20 10 48 4B AF CE 00 31 4A 31 4F 3B C0 45 40 61 4F
30 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 13 00 4C 6C 42 00 00 1E 00 00 00 FC 00 4C 47 20
50 4B 43 44 20 20 20 20 20 20 0A 00 00 00 FD 00 38
60 4B 1E 3E 08 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 33 32 4C 50 31 44 43 20 20 20 20 20 20 00 3E
- 13 -
3.2.2 Adjustment Method
A) Enter the 100% Vertical Color Bar Pattern (TVBAR_100)
of the 720P Mode supported for entry of component and
select entry selection to Component1 or Component2
and then select image to 'Normal'.
B) After waiting for more than a second after receipt of
signal, enter into 'Ez?Adjust' by pressing the ADJ Key on
the Adjustment R/C. Adjustment is automatically done if
pressing the (+) key after selecting the '1. AD9883ASet'.
C) If adjustment is normally completed, 'AD9883£≠Set'
message is displayed, and if not normally completed,
'AD9883A Setup Error' message is displayed.
D) If adjustment is completed, exit the adjustment mode by
pressing the ADJ key.
3.3 Color adjustment of main/subsidiary part
Color adjustment of main/subsidiary part is intended to
reduce color difference of the main/subsidiary part in the
PIP/POP/SPLIT Screen.
A) After entering inner signal, enter into the 'Ez?Adjust' by
pressing the ADJ key of the remote control for
adjustment and select the '2.VPX3226' and enter into the
Adjustment Mode by pressing the right key (
).
B) The screen automatically becomes a TV 6CH SPLIT
Screen if entering into the Adjustment and a window
appears as below.
< Screen Adjustment Command Table. (RS-232) >
C) Firstly adjust '1.Contrast (Main)' so that figure of "US
6CH" character of the left main screen is shown mostly
clearly and vividly (so that saturation is not done) and set
the '2.Contrast(Sub)' to same value. In this case, adjust it
by using the volume +/- key.
D) If adjustment is completed, exit the Adjustment Mode by
pressing the ADJ key.
<Adjustment Pattern : 720P Vertical Color Bar>
VPX3226
1. Contrast(MAIN)
31
2. Contrast(Sub) 31
US 6CH US 6CH
- 14 -
SVC REMOCON
NO KEY FUNTION
REAMARK
1 POWER
2 POWER ON
3 MUTE
4 P-CHECK
5 S-CHECK
6 ARC
7 CAPTION
8 TXT
9 TV/AV
10 TURBO SOUND
11 TURBO PICTURE
12 IN-START
13 ADJ
14 MPX
15 EXIT
16 APC(PSM)
17 ASC(SSM)
18 MULTIMIDIA
19 FRONT-AV
20 CH
21 VOL
22 ENTER
23 PIP CH-(OP1)
24 PIP CH+(OP2)
25 PIP SWAP(OP3)
26 PIP INPUT(OP4)
27 EYE
28 MENU
29 IN-STOP
30 STILL
31 TIME
32 SIZE
33 MULTI PIP
34 POSITION
35 MODE
36 PIP
37 TILT
38 0~9
To turn the TV on or off
To turn the TV on automatically if the power is supplied to the TV. (Use the
POWER key to deactivate): It should be deactivated when delivered.
To activate the mute function.
To check TV screen image easily.
To check TV screen sound easily
To select size of the main screen (Normal, Spectacle, Wide or Zoom)
Switch to closed caption broadcasting
To toggle on/off the teletext mode
To select an external input for the TV screen
To start turbo sound
To start turbo picture
To enter adjustment mode when manufacturing the TV sets.
To adjust the screen voltage (automatic):
In-start
mute Adjust AV(Enter into W/B adjustment mode)
W/B adjustment (automatic):
After adjusting the screen W/B adjustment Exit two times (Adjustment completed)
To enter into the adjustment mode. To adjust horizontal line and sub-brightness.
To select the multiple sound mode (Mono, Stereo or Foreign language)
To release the adjustment mode
To easily adjust the screen according to surrounding brightness
To easily adjust sound according to the program type
To check component input
To check the front AV
To move channel up/down or to select a function displayed on the screen.
To adjust the volume or accurately control a specific function.
To set a specific function or complete setting.
To move the channel down in the PIP screen.
To use as a red key in the teletext mode
To move the channel in the PIP screen
To use as a green key in the teletext mode
To switch between the main and sub screens
To use as a yellow key in the teletext mode
To select the input status in the PIP screen
To use as a blue key in the teletext mode
To set a function that will automatically adjust screen status to match
the surrounding brightness so natural color can be displayed.
To select the functions such as video, voice, function or channel.
To set the delivery condition status after manufacturing the TV set.
To halt the main screen in the normal mode, or the sub screen at the PIP screen.
Used as a hold key in the teletext mode (Page updating is stopped.)
Displays the teletext time in the normal mode
Enables to select the sub code in the teletext mode
Used as the size key in the PIP screen in the normal mode
Used as the size key in the teletext mode
Used as the index key in the teletext mode (Top index will be
displayed if it is the top text.)
To select the position of the PIP screen in the normal mode
Used as the update key in the teletext mode (Text will be
displayed if the current page is updated.)
Used as Mode in the teletext mode
To select the simultaneous screen
To adjust screen tilt
To manually select the channel.
Shortcut keys
Shortcut keys
Shortcut keys
Use the AV
key to enter
the screen
W/B
adjustment
mode.
Shortcut keys
Shortcut keys
Shortcut keys
- 15 -
TROUBLESHOOTING
No power
Connector connection
Replace Power_board
Replace Power_boardPower On key
OK
Power supply Check
connector connection status.
Stand voltage check:
D-board P810 '+5V-STDBY
Stand voltage check:
A-board P818 #5Pin 5V
Check 15V or 5V
of Lips
Connection
of power supply part :
Check wiring status of the 13-pin
connector
Connection
of power supply part :
Check wiring status of the 15-pin
connector
Power on signal level :
D-board P811 'power0' 3.3V
D_board main voltage:
P810 '+3.3V', '+6V-P',
'12V-P', '+30V-P'
Fail
Fail
Fail
Fail
Fail
Pass
Pass
Pass
Pass
Pass
Pass
Pass
Replace Power_board
Replace D_board
MICOM IC803
Loading...