LG 32LK450, 32LK450-CC, 37LK450, 37LK450-CC Service Manual

Internal Use Only

North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

LCD TV

SERVICE MANUAL

CHASSIS : LC01U

MODEL : 32LK450 32LK450-CC

37LK450

CAUTION

BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

37LK450-CC

Printed in ChinaP/NO :MFL67002803 (1104-REV00)

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ......................................................................... 3

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION ..............................................................61

EXPLODED VIEW ..................................................................................82

SVC. SHEET ...............................................................................................

- 2 -

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.

It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to

0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument’s
exposed
METALLIC PARTS

Good Earth Ground
such as WATER PIPE,
CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 4 -

CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.

2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its
assemblies.

4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.

7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.

4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).

7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500°F to 600°F.

2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wire­bristle (0.5 inch, or 1.25cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.

(500°F to 600°F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature

(500°F to 600°F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS

- 5 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.

2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and
solder it.

3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor
Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as
possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.

Power Output, Transistor Device
Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit
board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as
possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit
board.

3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor
Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.

2. Securely crimp the leads of replacement component around
notch at stake top.

3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).

1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.

1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

PDN

Internal Use Only

LG Electronics

Internal Use Only

LG Electronics

LC01U

PRODUCT SPEC.

Display Research lab.

LCD TV Product Development.

LG ELECTRONICS Inc.

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

- Contents -

1. Application Range

2. Specification

3. Test Method

4. Electrical Specification

5. Feature and Function

6. Safety and Regulation

7. Video

8. Digital Receiver

9. DVB-C

10. Chroma & Brightness

11. Audio

12. Power

13. External interface

14. Screen Size (over scan spec)

15. The others

16. Reliability

17. SET factoring condition

18. Accessories

19. Additional Rules

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

1. Application Range.

This spec sheet is applied to the LC01U chassis.

Chassis Model Name Market Place Brand Remarks

LC01U

32/37LK450-CC
42/47/55LK530-CC
32/37LV3500-CB
32LK330-CB
42/47/55LV4500-CA
42LV3650-CA
42/47/55LW4500-CA

CHINA, HONG KONG (PAL/DTMB Market) LG

2. Specification

Each part is tested as below without special appointment.

2.1 Temperature : 25±5℃ (77±9℉ ), CST : 40±5℃

2.2 Relative Humidity : 65±10%

2.3 Power Voltage : Standard input voltage (100-240V~ 50/60Hz)

Standard Voltage of each product is marked by models

2.4 Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM .

2.5 The receiver must be operated for about5 minutes prior to the adjustment

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

3. Test method

3.1 Performance : LGE TV test method followed.

3.2 Demanded other specification

Safety : CE, IEC specification

EMC : CE, IEC

Model Market Appliance Remarks

32/37LK450-CC
42/47/55LK530-CC
32/37LV3500-CB
32LK330-CB
42/47/55LV4500-CA
42LV3650-CA
42/47/55LW4500-CA

CHINA, HONG KONG(PAL/DTMB Market) Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

4. Electrical Specification

4.1 Module Specification

4.1.1 General Specification

No Item Specification

Meas
urem

ent

Result Remark

1 Display Screen Device 32”/37”/42”/47”/55”Wide color display module CCFL/EEFL LCD
2 Aspect Ratio 16:9

3 LCD Module

32” TFT LCD HD
32” TFT LCD FHD

37” TFT LCD FHD

42” TFT LCD FHD
47” TFT LCD FHD
55: TFT LCD FHD

BOE,IPS: 32LK330-CB
AUO,IPS:32LK450-CC
CMI:32LV3500-CB
LGD:32LV3500-CB
LGD:37LK450-CC
AUO,LGD:37LV3500-CB
LGD : 42LK530-CC/42LW4500/
42LV4500/42LV3650
LGD : 47LK530-CC/47LW4500/LV4500

LGD:55LK530-CC/55LW4500/LV4500
4 Storage Environment Temp. : -20 ~ 60 deg, Humidity : 10 ~ 90 %
5 Input Voltage 100-240V~ 50/60Hz

Power on (Blue)
32” BOE(HD)

Typ:80W

32” IPS(HD)

Typ:TBD

32” AUO(FHD)

Typ:78W

32” IPS(FHD)

Typ:TBD

32”CMI(FHD) Edge

Typ:95W

32”LGD(FHD) Edge

Typ:48.2W

37” LGD(FHD)

Typ : 132.68W

37” AUO(FHD) Edge

Typ : 61 W

37” LGD(FHD) Edge

Typ : 55.12 W

42”LGD(FHD,100Hz)

Typ: 158 W

42”LGD(FHD) Edge

Typ:91.3W

47”LGD(FHD,100Hz)

Typ: 203.1 W

6 Power Consumption

55” LGD(FHD,100Hz)

Typ: 248.2W

LCD(Module) + Backlight(Lamp)

32/37LV3500 Backlight(EDGE)

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Meas
urem

ent

Result Remark

42”LGD(FHD,100Hz)3DA

Typ:90.5W

42”LGD(FHD,100Hz) Edge

Typ: 80.2 W

47”LGD(FHD,100Hz)3D

Typ:101.1W

47”LGD(FHD,100Hz) Edge

Typ:90W

55”LGD(FHD,100Hz)3D

Typ:108.5W

55”LGD(FHD,100Hz) Edge

Typ:108.5W

32” BOE(HD) (H) 760.0 × (V) 450.0 × (t) 46.9 (m

m

32” IPS(HD) (H) 760.0 × (V) 450.0 × (t) 46.9 (m

m

32” AUO(FHD) 760(H)x450(V)x46.9(D) mm
32” IPS(FHD) (H) 760.0 × (V) 450.0 × (t) 46.9
32”CMI(FHD) Edge 698.4 (H) x 392.85 (V)
32”LGD(FHD) Edge 735.4(H)× 433.0(V)X10.8(B)/23.6(D)mm
37” LGD(FHD) 877(H)x516.8(V)x46.9mm(D)
37” AUO(FHD) Edge 856.4(H) x 501(V) x 21 (D)
37” LGD(FHD) Edge 856.4(H)× 501.0(V)X10.8(B)/23.6mm(D)

42”LGD(FHD,100Hz) 983.0(H) x 576.0 (V) x 46.0mm(D)

42”LGD(FHD) Edge 968.4(H)× 564(V)X10.8(B)/18.3mm(D)
47”LGD(FHD,100Hz) 1096.0(H) x 640.0 (V) x 35.5 mm(D)
55” LGD(FHD,100Hz) 1286.0(H) x 745.0 (V) x 60.0 mm(D)
42”LGD(FHD,100Hz)3D 968.4(H) x 564.0 (V) x 10.8(B) / 22.9 m

m

42”LGD(FHD,100Hz) Edge 968.4(H) × 564(V) X 10.8(B)/18.3 mm(

D

47”LGD(FHD,100Hz)3D 1078.6(H) x 626.0 (V) x 10.8(B) / 22.9

m

47”LGD(FHD,100Hz) Edge 1078.6(H) × 626.0(V) X 10.8(B)/22.9 m

m

55”LGD(FHD,100Hz)3D 1255.6(H) × 726.4(V) X 19.0(B)/10.8 m

m

Module Size

55”LGD(FHD,100Hz) Edge 1255.6(H) × 726.4(V) X 19.0(B)/10.8

m

32” BOE(HD) 170.25(H)x510.75(V)xRGB
32” IPS(HD) (H)0.51075×(V)0.51075
32” AUO(FHD) 0.36375(H)x0.36375(W) mm
32” IPS(FHD)

: (H) 0.36375 × (V) 0.36375

Pixel Pitch

32”CMI(FHD) Edge

0.12125 (H) x 0.36375 (V)

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Meas
urem

ent

Result Remark

32”LGD(FHD) Edge

0.36375mmx0.36375mm

37” LGD(FHD)

0.42675mmx0.42675mm
37” AUO(FHD) Edge 0.4268 (H) x 0.4268 (W)
37” LGD(FHD) Edge

0.42675mmx0.42675mm
42”LGD(FHD,100Hz)

0.4845 mm x 0.4845 mm
42”LGD(FHD) Edge

0.4845 mm x 0.4845 mm
47”LGD(FHD,100Hz)

0.5415 mm x 0.5415 mm
55” LGD(FHD,100Hz)

0.630 mm x 0.630 mm
42”LGD(FHD,100Hz)3D

0.4845 mm x 0.4845 mm
42”LGD(FHD,100Hz) Edge

0.4845 mm x 0.4845 mm
47”LGD(FHD,100Hz)3D

0.5415 mm x 0.5415 mm
47”LGD(FHD,100Hz) Edge

0.5415 mm x 0.5415 mm
55”LGD(FHD,100Hz)3D

0.630 mm x 0.630 mm
55”LGD(FHD,100Hz) Edge

0.630 mm x 0.630 mm
32” BOE(HD)

CCFL

32” IPS(HD)

CCFL

32” AUO(FHD)

CCFL

32” IPS(FHD)

CCFL

32”CMI(FHD)

Edge

32”LGD(FHD)

Edge

37” LGD(FHD)

EEFL

37” AUO(FHD)

Edge
37” LGD(FHD) Edge
42”LGD(FHD,100Hz)

EEFL
42”LGD(FHD) Edge

Edge
47”LGD(FHD,100Hz)

EEFL
55” LGD(FHD,100Hz)

EEFL
42”LGD(FHD,100Hz)3D

Edge
42”LGD(FHD,100Hz) Edge

Edge
47”LGD(FHD,100Hz)3D

Edge

Back Light

47”LGD(FHD,100Hz) Edge

Edge

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Meas
urem

ent

Result Remark

55”LGD(FHD,100Hz)3D

Edge
55”LGD(FHD,100Hz)Edge

Display Colors 1.06 Billion, 16.7 Milion
Coating 3H, AG

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

4.2 MODEL General Specification

No Item Specification Measurement Result Remarks
1 Market China(Hong Kong)

DTV & Analog - China, Hong Kong

2 Broadcasting system

1) PAL-DK

2) PAL-I

3) NTSC-M

4) DTMB

5) DVB-C

DTMB : DMB-T 와 ADTB-T 포함

3 Receiving system

Analog : Upper Heterodyne
Digital : COFDM, QAM

4 Video Input RCA(2EA) PAL, NTSC

Rear 1EA, Side 1EA

5 Component Input (2EA) Y/Cb/Cr, Y/Pb/Pr
6 RGB Input RGB-PC

Analog (D-SUB 15PIN)

7 HDMI Input(3EA)

HDMI1-DTV/DVI
HDMI2-DTV (side/rear)
HDMI3-DTV (side

Except 42LV3650 )

PC(HDMI version 1.3), Support HDCP

8 Audio Input (3/4/5EA)

RGB/DVI Audio
Component(1/2EA)
AV(1/2EA)

L/R Input

9 SDPIF out (1EA) SPDIF out

Rear

10. Earphone out (1EA)

Side( Except 42LV3650 )

l11 USB (1EA) Divx(HD), EMF(JPEG, MP3), SVC(download)

Side

5. Feature and Function

No Item Specification

Measurement Result

Remarks

1. TV/ DTV Input 2

Analog : PAL DK, I, NTSC-M
Digital : DTMB, DVB-C

Rear (2EA)

2. RGB Input 1 Analog RGB (Separate)

D-Sub 15 pin, Rear (1EA)

3. HDMI Input 3

Rear(2EA), Side (1EA)

4. AV Input 2 CVBS/L/R

Rear (1EA) Side(1EA)

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Measurement Result

Remarks

5. Component Input 2

Rear (2EA)

6. RS-232C 1 Control & Service

Rear (1EA)

7. Audio Input 5 RGB/DVI(1EA), Component(2EA), AV(2EA)

Rear (4EA), Side (1EA)

8. SPDIF Output 1 SPDIF out

Rear (1EA)

9. USB

1 Divx(HD),EMF (JPEG, MP3),SVC (download)

Side (1EA)

10 Remocon Code LG code
11 Remote control Wireless Remote Control
12 Local Key

POWER ON/OFF, INPUT, MENU, OK, -△+, ▼P▲

8EA

13 Set Installation Wall Mount / Desk top
14 Main Power Key O
15 Favorite O
16 AVL O
17 On/Off Timer O
18 Aspect Ratio 16:9 / Original / 4:3 / 14:9 / Zoom / Cinema Zoom

19 Picture Mode

Vivid / Standard / Natural /
Cinema / Sport / Game / Expert1 / Expert2

20 Sound Mode Standard / Music / Cinema / Sport / Game

Auto Tuning

Quick(Home Tuning/Network ID/Start and End frequency) / Full
OK
Close

Manual Tuning

DTV (UHF CH)
TV (Storage, System, Band, Channel, Search, Name)
Cable DTV (Frequency,Symbol Rate, Modulation)
Cable TV (Storage, System, Band, Channel, Search, Name)

Programme Edit

Pr.change, Favourite Pr. Q.Menu, Block/unblock, Page Change,
Previous, Skip, Move, Delete

(common except Cable DTV
and Cable RADIO)
(only for TV and Cable TV)

Booster On/Off

DTV Mode

CI Information

*Except Hong Kong

21

Menu
(SETUP)

Cable DTV Setting

Service Operator
Channel Auto update : On/Off
Audio Auto Mode : On/Off

*Except Hong Kong

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Measurement Result

Remarks

Aspect Ratio

- 16:9 : DTV, ATV, AV1/2, Component1/2, RGB, HDMI1~3

- Original : DTV, ATV, AV1/2

- 4:3 : DTV, ATV, AV1/2, Component1/2, RGB, HDMI1~3

- 14:9 : DTV, ATV, AV1/2, Component1/2, HDMI1~3

- Zoom : DTV, ATV, AV1/2, Component1/2, HDMI1~3

- Cinema Zoom : DTV, ATV, AV1/2, Component1/2, HDMI1~3

HDMI(720P↑ )
Component(720P↑ )

Picture Wizard

Energy Saving

Auto

Off
Minimum
Medium
Maximum
Screen Off

Intelligent Sensor except LK330

Vivid / Standard / Cinema / Sport /
Game / Expert1 / Expert2
Backlight
Contrast
Brightness
Sharpness
Colour
Tint
Colour Temp.

Advanced
Control

Dynamic Contrast : Off, Low, Medium, High
Dynamic Colour : Off, Low, High
Clear White : Off, Low, High
Skin Color : -5 ~ 5
Noise Reduction : Off, Low, Medium, High, Auto
Digital Noise Reduction : Off, Low, Medium, High
Gamma : Low, Medium, High
Black Level : Low, High, Auto
Eye Care : on/off
Real Cinema : on/off
Color Gamut : Wide, Standard

xvYCC : On, Off

22

Menu
(PICTURE)

Picture Mode

Picture reset

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Measurement Result

Remarks

TruMotion

User
Low
High

Only LK530 /LW4500
/LV4500

LED Local Dimming

On
Off

Only LW4500

Screen

Resolution
Auto Config
Position
Size
Phase
Reset

RGB

Auto volume

Off / On

Clear Voice II

Off / On(Level -6 ~ 6)

Balance

0 (L50 ~ R50)

Sound Mode

Standard /Music /Cinema /Sport /Game
Infinite Sound : Off/On
Treble
Bass
Reset

Digital Audio Out

Auto, PCM

TV Speaker

On/ Off

23 Menu

(Audio)

DTV Audio Setting

Auto, HE-AAC, AAC, Dolby Digital+, Dolby Digital, MPEG

Clock

Auto / Manual (Year, Month, Date, Hour, Minute)

Off Time

Repeat(Off, Once, daily, Mon~Fri, Mon~Sat, Sat~Sun, Sun),
Hour, Minute

On Time

Repeat(Off, Once, daily, Mon~Fri, Mon~Sat, Sat~Sun, Sun),
Hour, Minute, Input, Programme, Volume

24

Menu
(TIME)

Sleep timer

Off/10min/20min/30min/60min/90min/120min/180min/240min

Set Password Off / On
Lock System Off / On(Block Programme, Input Block)

25

Menu
(Lock)

Key Lock Off / On

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

No Item Specification

Measurement Result

Remarks

Menu Language

Chinese / English

Audio Language

Mandarin / English

Language

Subtitle Language

Mandarin / Cantonese / English
City/Area Mainland China, Hong Kong
Hard of hearing

Off / On
Power Indicator Standby Light/Power Light : Off/On
MHEG Guide

Off / On

* Only Hong Kong

Factory Reset

Yes / No
Set ID 1 ~ 99

26

Menu
(Option)

Mode Setting Home Use / Store Demo

27

Menu
(Input)

Antenna, Cable, USB,
AV1/2, Component1/2,
RGB, HDMI1/2/3

28 Menu (USB)

Movie List,
Photo List,
Music List

INPUT
TV/RAD
Energy saving
Q.MENU
MENU
GUIDE
RETURN
INFO
AV MODE

Etc.

POWER, Navigation key (Up, Down ,Left ,Right ), OK,

Numeric(0~9), P +/-, Δ +/-,

RED key, GREEN key, YELLOW key, BLUE key, SUBTITLE,SIMPLINK

MARK Favorite List
MUTE Audio Mute

29

Hot Key
(Remote)

LIST

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

6. Safety and Regulation

No Item Min Typ Max Unit   Remarks

1. Force Stability – Incline Plane Tip Test 10 12  Deg   IEC60065

2. Clearances & Creepage : AC-AC 3   mm   

3. Clearances & Creepage : AC-GND 3   mm   

4.

Clearances & Creepage : Primary ↔
Secondary

6   mm   

32LK450-CC(AUO) 85 120

 Test method for
Power consumption(Typ.)

32LK450-CC(IPS) TBD 120

37LK450-CC 118 160

And Energy saving :
refer to 14 page.

42LK530-CC 139 200 

47LK530-CC 150 250

 Dielectric Voltage

(AC↔FG)
55LK530-CC 208 320 - 1.5kV/100mA/1min
32LV3500-CB(CMI) 59 80
32LV3500-CB(LGD) TBD 80 - 1.8kV/100mA/1sec(M/P)
37LV3500-CB(AUO) 72 100 

37LV3500-CB(LGD) TBD 100



32LK330-CB(BOE) 96 120



32LK330-CB(IPS) 91 120

 Dielectric Voltage

(WITHOUT FG)

42LV3650-CA TBD 110



42LV4500-CA TBD 120



5.

Power Consumption,
Max

47LV4500-CA



TBD 140

W  



LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

55LV4500-CA TBD 160



42LW4500-CA 108 120



47LW4500-CA 112 140



55LW4500-CA 125 160

7.

Power Consumption,
Stand by

All-inch   1 W  

External interface signal

line↔AC

8. Dielectric Voltage 1.5   Kv  

- 3kV/100mA/1min

9. Dielectric Voltage(for M/P) 1.8   Kv 

10 ㏁

- 3.6kV/100mA/1sec

10. Isolation Resistance 4 



㏁

 



 UL/CSA   0.5 mA (rms)  

11.

Leakage Current

Etc.   0.35 V Peak  



12. Power cord Length 1.6 1.8 3 M  
13 Sharp Edge None     



Safety K60065

Not
Applied

  

Korea Compliance

EMC MIC Class A / B

Not
Applied

  

Safety UL6500    

UL Compliance

EMC FCC Part 15 Class A / B Applied   
Safety CSA60065    

CSA Compliance

EMC GRR Part II A   
Safety IEC60065, D   

IEC Compliance

EMC CISPR Applied

  

Safety EN60065 Applied 

 

EN55013, EN55020 Applied   
EN61000-3-2 Harmonics   
EN61000-3-3 Flicker   

14

CE Compliance

EMC

EN61000-4-2 ESD   

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

EN61000-4-3 Radiated   
EN61000-4-4 EFT   
EN61000-4-5 Surge   

EN61000-4-6

Conducted
immunity

  

EN61000-4-11 Applied   

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

※ Test method for Power consumption (Typ.) and Energy saving

* Measurement Condition

- Input voltage : 100V, 50Hz

- RF input : 100% color bar,1kHz sine wave

- Video : Max condition

- Audio : Sound Max 1/8

※ Test method and Spec for Energy saving

* Measurement Condition

- Input voltage : 220V, 50Hz

- RF input : Full White, Video modulation 87.5%, Audio modulation 50Khz

- Picture mode : Vivid

- Volume level : 30

* Spec.

Mode Measure Spec. Remark

Off A wattage (Reference) = 100% 100(%)

Minimum B wattage Æ B/A*100% 75±15 (%)

Medium C wattage Æ C/A*100% 53±15 (%)

Maximum D wattage Æ D/A*100% 30±15 (%)

Screen Off E wattage Æ E/A*100% 15±15 (%)

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

7. Video

No Item Min Typ Max Unit Remarks

1. IF Rejection Ratio -13.0 dB

2. Image Rejection Ratio -13.0 dB

3. Adjacent CH Rejection, Upper -6.0 dB

4. Adjacent CH Rejection, Lower -13.0 dB

5. Sync Level 35 %

6. Color 7 %

7. AFT -1.5 +1.5 MHz

8. AGC speed 100 Hz Multi-Tuner

9. Sub Carrier Pull In Range -450 +450 Hz

10. Sub Carrier Delay -1.5 +1.5 usec

11. AV Video Out Level 0.85 1.0 1.15 Vpp AV Out

12. AV Video Sync Out Level 0.25 0.3 0.35 Vpp

13. AV Burst Out Level 0.15 0.3 0.35 Vpp

14. AV Video Out Frequency Characteristic 3.0 MHz

15. AV Video Out S/N 40.0 dB

16. Color Distortion, DG 10 %

17. Color Distortion, DP 10 deg

18. Color S/N, AM 43 dB

19. Color S/N, PM 43 dB

20. AV Video In Level 0.85 1 1.15 Vpp

21. AV Sync In Level 0.25 0.3 0.35 Vpp

22. AV Burst In Level 0.15 0.3 0.35 Vpp

23. AV Video In Impedance 100kHz 67.5 75 82.5 Ohm

24. AV Video In Impedance 2MHz 67.5 75 82.5 Ohm

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

8. Digital Receiver

8-1.Digital Receiver (DTMB : ADTB-T) : C=1, 16QAM, 0.8, PN=595, M=720

No Item Min Typ Max Unit

Remarks

1 Frequency Range

474

52.5

866
219

MHz

UHF BAND

VHF BAND
2 Input Impedance 75 Ω
3 Carrier C=1
4 Modulation 4QAM, 16QAM, 32QAM
5 Code Rate 0.8
6 Frame Header PN595
7 Interleaver M=720

8-1 RF Sensitivity(VHF) -85 -25 dBm
8-2 RF Sensitivity(UHF) -83 -25 dBm

9 Channel Offsets ±150 kHz

10 C/N with AWGN 14 dB
11-1 PAL CCI Protection (Analog) 2 dB
11-2 PAL CCI Protection (Digital) 14 dB
12-1 PAL ACI protection(Analog Lower) -3H7 dB
12-2 PAL ACI protection(Analog Upper) -36 dB
12-3 PAL ACI protection(Digital) -28 dB

13 Ricean channel C/N 15 dB

14 Rayleigh channel C/N 18 dB

8-2.Digital Receiver (DTMB : DMB-T) : C=3780, 16QAM, 0.8, PN=420, M=720

No Item Min Typ Max Unit

Remarks

1 Frequency Range

474

52.5

866
219

MHz

UHF BAND

VHF BAND
2 Input Impedance 75 Ω
3 Carrier C=3780

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

4 Modulation 16QAM, 64QAM
5 Code Rate 0.4, 0.6, 0.8
6 Frame Header PN420, PN945
7 Interleaver M=720

8-1 RF Sensitivity(VHF) -85 -25 dBm
8-2 RF Sensitivity(UHF) -83 -25 dBm

9 Channel Offsets ±150 kHz

10 C/N with AWGN 14 dB
11-1 PAL CCI Protection (Analog) 2 dB
11-2 PAL CCI Protection (Digital) 14 dB
12-1 PAL ACI protection(Analog Lower) -37 dB
12-2 PAL ACI protection(Analog Upper) -36 dB
12-3 PAL ACI protection(Digital) -28 dB

13 Ricean channel C/N 15 dB

14 Rayleigh channel C/N 18 dB

9. DVB-C

No Item Min Typ Max Unit

Remarks

1. Frequency Range 52.5 866 MHz

2. Input Impedance 75 Ω

3. Symbol Rate

4000 Ks/s~7200 Ks/s

4. Modulation 16, 64, 128, 256QAM
5 RF Sensitivity 47 70 dBuV

16QAM 20.5 dB
32QAM 26.5 dB
64QAM 29.5 dB

128QAM 31.5 dB

6. C/N with AWGN

256QAM 32.5 dB

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

10. Chroma & Brightness

10.1. Module optical specifications.

*** LGD module Uniformity Measurement Position***

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

* 32” LCD Module (BOE HD): HV320WXC-100

for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 89 Degree

Luminance (cd/m2) 380 450

2. Luminance
Variation - 1.3 MAX / MIN

3. Contrast Ratio CR 900 1200

WX 0.279

White

W

Y

0.292

RX 0.636

RED

Ry 0.335
Gx 0.291

Green

Gy 0.603
Bx 0.146

4. CIE Color Coordinates

Blue

By

Typ

-0.03

0.061

Typ

+0.03

z 32” LCD Module (IPS HD): VVX32H109G00

z for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 89 Degree

Luminance (cd/m2) 300 400

2. Luminance
Variation - 1.3 MAX / MIN

3. Contrast Ratio CR 700 1200

WX 0.278

White

W

Y

0.285

RX 0.645

RED

Ry 0.330

4. CIE Color Coordinates

Green

Gx

Typ

-0.03

0.300

Typ

+0.03

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

Gy 0.620
Bx 0.153

Blue

By 0.065

z 32” LCD Module (AUO FHD) : T315HW 04-V9

for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 89 Degree

Luminance (cd/m2) 320 400

2. Luminance
Variation - 0.04 MAX / MIN

3. Contrast Ratio CR 3200 4000

WX 0.28

White

W

Y

0.29

RX 0.64

RED

Ry 0.33
Gx 0.29

Green

Gy 0.60
Bx 0.15

4. CIE Color Coordinates

Blue

By

Typ

-0.03

0.06

Typ

+0.03

1) Standard Test Condition (The unit has been ‘ON’)

2) Stable for approximately 30 minutes in a dark environment at 25±2℃

3) The values specified are at approximate distance 50Cm from the LCD surface

4) T

a

= 25±2°C, V

LCD

=12.0V, fV=60Hz, D

clk

=74.25MHz VBR_A=1.65V, EXTV

BR_B

=100%

z 32” LCD Module (IPS FHD) : VVX32F109G00

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 89 Degree

Luminance (cd/m2) 300 400

2. Luminance
Variation - 0.04 MAX / MIN

3. Contrast Ratio CR 700 1200

WX 0.278

White

W

Y

0.285

RX 0.645

RED

Ry 0.330
Gx 0.330

Green

Gy 0.620
Bx 0.153

4. CIE Color Coordinates

Blue

By

Typ

-0.03

0.065

Typ

+0.03

1) Standard Test Condition (The unit has been ‘ON’)

2) Stable for approximately 30 minutes in a dark environment at 25±2℃

3) The values specified are at approximate distance 50Cm from the LCD surface

4) T

a

= 25±2°C, V

LCD

=12.0V, fV=60Hz, D

clk

=74.25MHz VBR_A=1.65V, EXTV

BR_B

=100%

32” LCD Module (CMI FHD) : V315H3-LE7

z for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 88 Degree

Luminance (cd/m2)

280 350

2. Luminance
Variation - 1.3 MAX / MIN

3. Contrast Ratio CR 3500 5000

WX 0.280 4. CIE Color Coordinates

White

W

Y

Typ

-0.03

0.290

Typ

+0.03

LGE Display Division LG(56) C1-1480-00

Establish :
Reform :

LG 전자

LC01U Product Specification

RX 0.635

RED

Ry 0.323
Gx 0.288

Green

Gy 0.600
Bx 0.148

Blue

By 0.050

1) Standard Test Condition (The unit has been ‘ON’)

2) Stable for approximately 30 minutes in a dark environment at 25±2℃

3) The values specified are at approximate distance 50Cm from the LCD surface

4) T

a

= 25±2°C, V

LCD

=12.0V, fV=60Hz, D

clk

=74.25MHz VBR_A=1.65V, EXTV

BR_B

=100%

z 32” LCD Module (LGD FHD) : LC320EUN-SDV2

for more details, refer to the module spec.

No. Item Specification Min. Typ. Max. Remark

1.

Viewing Angle(CR>10) Right/Left/Up/Down 88 Degree

Luminance (cd/m2)

290 360

2. Luminance
Variation - 1.3 MAX / MIN

3. Contrast Ratio CR 1000 1400

WX 0.279

White

W

Y

0.292

RX 0.637

RED

Ry 0.346
Gx 0.320

Green

Gy 0.606
Bx 0.152

4. CIE Color Coordinates

Blue

By

Typ

-0.03

0.055

Typ

+0.03

1) Standard Test Condition (The unit has been ‘ON’)

2) Stable for approximately 30 minutes in a dark environment at 25±2℃