LG 32LG700HUA Users manual

Order Number : GETEC-C1-09-001

Test Report Number : GETEC-E3-09-001 FCC Class B Certification

APPENDIX H

: USER’S MANUAL

EUT Type: LCD TV/Monitor

FCC ID.: BEJ32LG700HUA

LCD TV OWNER’S MANUAL

32LG700H 37LG700H 42LG700H

Inst

aller Reference for Commercial Mode MPI/PPV Card Setup see page 19 Commercial Mode Setup see pages 87-104

Please read this manual carefully before operating your set.

Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.

This product qualifies for ENERGY STAR in the “factory default (Home mode)” setting and this is the setting in which power savings will be achieved.

Changing the factory default picture setting or enabling other features will increase power consumption that could exceed the limits necessary to quality for Energy Star rating.

P/NO : SAC30708043 (0810-REV00)

www.lgcommercial.com

WARNING / CAUTION

To prevent fire or shock hazards, do not expose this product to rain or moisture.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Protect the power cord from being walked on

or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by

the manufacturer.

Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Unplug this apparatus during lighting storms or

when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Never touch this apparatus or antenna during a

GROUNDING

DISCONNECTING DEVICE FROM MAINS

thunder or lighting storm.

When mounting a TV on the wall, make sure not to

install the TV by the hanging power and signal cables on the back of the TV.

Do not allow an impact shock or any objects to fall

into the product, and do not drop onto the screen with something.

CAUTION concerning the Power Cord :

It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

WARNING - To reduce the risk of fire or electrical

shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not

place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).

Ensure that you connect the earth ground wire to prevent possible electric shock. (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grouned AC outlet) If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Short-circuit

Breaker

Mains plug is the disconnecting device. The plug must remain readily operable.

Power Supply

Keep the product away from direct sunlight.

ANTENNAS Outdoor antenna grounding

Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductors (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Cleaning

When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

Moving

Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.

Ventilation

Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.

If you smell smoke or other odors coming from the

TV or hear strange sounds, unplug the power cord contact an authorized service center.

NEC: National Electrical Code

Do not press strongly upon the panel with a hand or

sharp object such as nail, pencil or pen, or make a scratch on it.

CONTENTS

WARNING / CAUTION SAFETY INSTRUCTIONS FEATURES OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . . . . . . . . . . . . . . . . . . . . . . . . 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel Information Back Panel Information Stand Instruction Cable Management Desktop Pedestal Installation Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Attaching the TV to a desk VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Securing the TV to the wall to prevent falling When the TV is used on a stand Antenna or Cable Connection MPI Card Slot / PPV Card Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . 17

. . . . . . . . . . . . . . . . . . . . . . . . . . 18

. . . . . . . . . . . . . . . 19

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

- Component Connection

- HDMI Connection

- DVI to HDMI Connection

DVD Setup

- Component Connection

- HDMI Connection

VCR Setup

- Antenna Connection

- Composite (RCA) Connection Other A/V Source Setup PC Setup

- VGA (D-Sub 15 pin) Connection

- DVI to HDMI Connection

- Screen Setup for PC mode Audio Out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . 20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

. . . . . . . . . . . . . . . . . . . . . . . . . . 22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

. . . . . . . . . . . . . . . 27

. . . . . . . . . . . . . . . . . . . . . . . . . . 28

. . . . . . . . . . . . . . . . . . . . . . . . 29

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

- Auto Scan (Auto Tuning)

- Add / Delete Channel (Manual Tuning)

- Channel Editing Channel Label Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

. . . . . . . . . . . . . . . . . . . . . . . . . . . 39

. . . . . . 40

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 44

Preset Picture Settings

- Picture Mode - Preset

- Color Tone - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Manual Picture Adjustment

- Picture Mode - User Mode Picture Improvement Technology Advanced Control - Black (Darkness) Level Eye Care Advanced Control Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Film Mode . . . . . . . . . . . . . . . . . . . . . . . . .53

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

. . . . . . . . . . . . . . . . . . . . . . . . 49

. . . . . . . . . . . . . . . . . . . . . 50

. . . . . . . 51

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 55

Preset Sound Settings (Sound Mode) Sound Setting Adjustment - User Mode

- SRS TruSurround XT Clear Voice Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

TV Speakers On/Off Setup Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Stereo/SAP Broadcast Setup Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

. . . . . . . . . . . . . . . . . . . . . . . . . . . 63

On-Screen Menus Language Selection

. . . . . . . . . . . . . . 56

. . . . . . . . . . . 57

. . . . . . . . . . . . . 65

Caption Mode

- Analog Broadcasting System Captions

- Digital Broadcasting System Captions

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

. . . . . . . 66

. . . . . . . . 67

TIME SETTING

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On TV Channel Selection Volume Adjustment On-Screen Menus Selection Channel Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

- Manual Clock Setup Auto On/Off Time Setting Sleep Timer Setting Auto Shut-off Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Channel Blocking Movie & TV Rating Downloadable Rating External Input Blocking Example Electronic Program Guide Interactive TV Setup PIP (Picture-In-Picture)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

. . . . . . . . . . . . . . . . . . . 83

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

COMMERCIAL MODE SETUP

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Interactive TV Overview Commercial Mode Setup for Master TV TLL-1100A Cloning Connections/Learning Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

LT2002 Cloning Connections/Learning Setup LT2002 Cloning Learning Setup Cloning Connections/Teaching Setup Installer Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Reference: Detailed Instructions For Making A Master TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0

Reference: Procedures for adding Channel Label Icons/Custom Channel Labels (2-5-4 + MENU Mode)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Reference: Clonable Menu Features Reference: Power Saving Setup TV Aux Input Configuration TV Camport Auto Sense Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

. . . . . . . . . . . . 89

. . 91

. . . . . . . . . . . . . . . . . . . . . . 92

. . . . . . . . . . . . . . 93

. . . . . . . . . . . . . . . . 10 2

. . . . . . . . . . . . . . . . . . . . . . . 10 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3

. . . . . . . . . . . . . . . . 10 4

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5

Reference: LT2002 Cloning Procedure Troubleshooting

Troubleshooting Flow Chart Commercial Mode Check Glossary of Terms Maintenance Product Specifications Programming the Remote Control IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7

. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

. . . . . . . . . . . . . . . . . . . 112

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

FEATURES OF THIS TV

USB IN

SERVUCE ONLYSERVUCE ONLY

HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."

USB port shall be used for software update by service personnel only.

Manufactured under license from Dolby Laboratories.

Dolby

“and the double-D symbol are trademarks of

“ Dolby Laboratories.

is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

FOR LCD TV

■

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.

■

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.

■

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.

PREPERATION

Option Extras

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner’s Manual

Cable Holder

(Refer to P.13)

Polishing Cloth

(This feature is not avail-

able for all models.)

D-sub 15 pin Cable

CD Manual

4xL20

(Plastic Screw)

Screw for stand fixing

(Refer to P.15)

* Wipe spots on the exterior only with the pol-

ishing cloth.

* Do not wipe roughly when removing stains.

Excessive pressure may cause scratches or discoloration.

When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.

Power Cord

x 4 x 4

M4xL26

(Machine Screw)

4xL20

(Plastic Screw)

Bolts for stand assembly

(Refer to P.12)

Protective Bracket and

Bolt for Power Cord

(Refer to P.13)

x 2

M4xL22

(Machine Screw)

Torx plus

Star head screw

(Refer to P.12)

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

■

NOTE: If your TV has a protection tape attached, remove the tape. And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).

PREPARATION

Stand

Power/Standby Indicator

Illuminates red in standby mode. Illuminates blue when the set is switched on.

Remote Control Sensor

POWER Button

VOL

ENTER

INPUT

CHANNEL(+, -) Buttons

VOLUME (+, -) Buttons

ENTER Button

MENU Button

INPUT Button

PREPARATION

ANTENNA IN

M.P.I.

BACK PANEL INFORMATION

■

Image shown may differ from your TV.

PREPARATION

USB

SERVICE ONLY

AUDIO

L/ MONO

VIDEO

ANTENNA IN

HDMI/DVI IN

1(DVI)

M.P.I.

LAN

(SERVICE ONLY)

RGB(PC)

RESET

AUDIO

(RGB/DVI)

UPDATE

RS-232C IN

(SERVICE ONLY)

AV IN 2

OPTICAL

DIGITAL

AUDIO OUT

SPEAKER OUT

REMOTE

CONTROL OUT

RGB IN

RJP

INTERFACE

VIDEO

COMPONENT IN

AUDIO

AV IN 1

AUDIO

MONO

VIDEO

HDMI/DVI IN

Digital Connection. Supports HD video and Digital audio.

Accepts DVI video using an adapter or HDMI to DVI cable (not included)

LAN (SERVICE ONLY) Connect to control network.

UPDATE

Software downloads and debug mode enable/disable.

RESET

Hardware reset to PTC microcontroller.

OPTICAL DIGITAL AUDIO OUT

Digital audio output for use with amps and home theater systems.

Includes an optical connection. Note: In standby mode, these ports do not work.

SPEAKER OUT 8

Connect to external speaker input.

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable).

AUDIO (RGB/DVI)

1/8” headphone jack for analog PC audio input.

REMOTE CONTROL OUT

IR output for controlling an auxiliary device.

RJP INTERFACE (REMOTE JACK PACK PORT)

Connect to remote jack pack control output port.

COMPONENT IN

Analog Connection. Supports HD. Uses a red, green, and blue cable for video & a red

and white cable for audio.

AV (Audio/Video) IN

Analog composite connection. Supports standard definition video only (480i).

Used for PC/DTV audio input jack.

USB SERVICE ONLY

Used for software updates.

ANTENNA IN

Connect over-the air signals to this jack.

M.P. I.

Power Cord Socket

For operation with AC power. Caution: Never attempt to operate the TV on DC

power.

PREPARATION

RS-232C IN (SERVICE ONLY)

Used for software updates.

PREPARATION

STAND BODY

COVER B A SE

STAN D BOD Y

COVER B A SE

STAND INSTRUCTION

■

Image shown may differ from your TV.

PREPARATION

INSTALLATION

Carefully place the TV screen side down on a

cushioned surface to protect the screen from damage.

Assemble the parts of the

with

Insert the stand as shown.

of the TV.

DETACHMENT

Carefully place the TV screen side down on a

cushioned surface to protect the screen from damage.

Remove the four screws that hold the base on.

Detach the stand from TV.

x 4

Tighten the stand with the four screws (provided as parts of the TV).

x 2

(provided as parts of the TV) to secure the TV. Tighten the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV).

Tighten the two of these four screws

x 2

and the two Torx plus star head screws

NOTE

Make sure the screws in the stand are fully

tightened. (If not tightened fully, the product could tilt forward and fall). But do not over tighten, over-tightening can damage the threads on the screws.

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.

To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cable with the

PROTECTIVE BRACKET and the screw as shown. It will help prevent the power cable from being removed by accident.

PROTECTIVE BRACKET

(This feature is not available

for all models.)

Install the CABLE MANAGEMENT CLIP as

shown. If your TV has the CABLE HOLDER, install it

as shown and bundle the cables.

Put the cables inside the CABLE MANAGEMENT

CLIP and snap it closed.

NOTE

Do not hold the CABLE MANAGEMENT CLIP when moving the TV.

- If the TV is dropped, you may be injured or the product may be broken.

PREPARATION

CABLE MANAGEMENT CLIP

CABLE HOLDER

PREPARATION

DESKTOP PEDESTAL INSTALLATION

■

Image shown may differ from your TV.

* This feature is not available for all models.

PREPARATION

For proper ventilation, allow a clearance of 4 inches on all four sides.

4 inches

CAUTION

Ensure adequate ventilation by following the clearance recommendations.

Do not mount near or above any type of heat source.

SWIVEL STAND

The TV can be conveniently swivelled on its stand 90° to the left or right to provide the optimum viewing angle.

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only the included screw.

Stand

1-Screw

(provided as parts of the product)

Desk

WARNING

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury.

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materi-

PREPARATION

als, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall.

Product Model

32LG700H

LCD TV

37LG700H

42LG700H

NOTE

Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount.

Standard dimensions for wall mount kits are shown in the table.

When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.

Do not use screws longer then the standard dimension, as they may cause damage to the inside to the TV.

For wall mounts that do not comply with the VESA

VESA

(A *B)

200 * 100

200 * 200

standard screw specifications, the length of the screws may differ depending on their specifications.

Do not use screws that do not comply with the VESA standard screw specifications.

Do not tighten the screws too much. It may damage the TV or allow the TV to a fall and cause personal injury. LG is not liable for these kinds of accidents.

LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installation instructions.

Standard Screw Quantity

CAUTION

Do not install your wall mount kit while the TV is plugged in. It may result in personal injury due to electric shock.

WARNING

To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.

SECURING THE TV TO THE WALL TO PREVENT FALLING

G G

WHEN THE TV IS USED ON A STAND

■

You should purchase necessary components to prevent TV from falling off of the stand.

■

Image shown may differ from your TV.

* This feature is not available for all models.

We recommend that you set the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert eye-bolts (or TV brackets and bolts) to attach the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with screws (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

PREPARATION

■

Use a sturdy rope or cord (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product (the less slack in the rope, the better).

NOTE

Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are the same.

ANTENNA IN

PREPARATION

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

ANTENNA OR CABLE CONNECTION

PREPARATION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection.

For optimum picture quality, adjust the direction if needed.

Wall

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Antenna Socket

Outdoor

RF Coaxial Wire (75 ohm)

Antenna (VHF, UHF)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

2. Cable

ANTENNA IN

Copper Wire

Be careful not to bend the copper wire when connecting the antenna.

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

MPI CARD SLOT / PPV CARD INSTALLATION

ANTENNA IN

M.PM.P.I.

M.P. I.

Card Slot

The MPI card is equipped with an RF jack for antenna/cable signal source connection. The MPI card slot is also available for installing a PPV (Pay-Per-View) card.

MPI Card Removal / PPV Card Installation

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

2. Detach RF cable.

3. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

4. Insert card all the way into the slot making sure it is fully seated into back plane connector.

5. Replace the two card retainer screws.

RF CABLE

RF cable needs to be disconnected to remove current card.

PREPARATION

EXTERNAL EQUIPMENT SETUP

COMP O NENT IN VIDEO

COMP O NENT I N A UDI O

Comp one n t

INP UT

UPDA

RESET

LAN

(SERVICE ONLY)

RGB IN

RGB(PC)

AUDIO

(RGB/DVI)

COMPONENT IN

VIDEO

AUDIO

Y L RP

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

This part of EXTERNAL EQUIPMENT SETUP mainly uses the picture for 42LG700H model.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,

PREPARATION

if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

Component Connection

1. How to connect

)

Connect the video outputs (Y, PB, PR

top box to the the TV. Match the jack colors (Y = green, P

R = red).

of the digital set-

jacks on

B = blue, and

2. How to use

■

Turn on the digital set-top box. (

Refer to the owner’s manual for the digital set-top box.

■

Select on the remote control.

Supported Resolutions

Signal

480i

480p

720p

10 8 0 i

10 8 0 p

Connect the audio output of the digital set-top box to the

jacks on the TV.

)

input source using the

button

Y, CB/PB, CR/PR

Component

Yes

HDMI

Resolution

720x480i

Yes

720x480p

1280x720p

Horizontal Vertical

Frequency(KHz)Frequency(Hz

15.73 59.94

15.73 60.00

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

)

1920x1080i

33.72 59.94

33.75 60.00

HDMI Connection

HDMI/ D VI IN

HD M I

INP UT

RGB IN

VID

HDMI/DVI IN

1(DVI)

RJP

INTERFACE

HDMI-DTV OUTPUT

1. How to connect

Connect the digital set-top box to

jack on the TV.

No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

■

Turn on the digital set-top box. (

Refer to the owner’s manual for the digital set-top box.

■

Select on the remote control.

input source with using the

)

button

HDMI-DTV

Resolution

Horizontal Vertical

Frequency(KHz)Frequency(Hz

EXTERNAL EQUIPMENT SETUP

)

720x480p

1280x720p

1920x1080i

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

EXTERNAL EQUIPMENT SETUP

RESET

LAN

(SERVICE ONLY)

RGB IN

RGB(PC)

COMPONENT IN

VIDEO

RJP

INTERFACE

AUDIO

(RGB/DVI)

HDMI/DVI IN

1(DVI)

DVI-DTV OUTPUT

HDMI /DVI I N

AUDI O (RG B /DV I )

HD M I

INPUT

DVI to HDMI Connection

1. How to connect

EXTERNAL EQUIPMENT SETUP

Connect the DVI output of the digital set-top box to

the

Connect the audio output of the digital set-top box to

the

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.

■

Select the button on the remote control.

NOTE

A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary.

jack on the TV.

input source on the TV using the

jack on the TV.

)

DVD SETUP

COMP O NENT I N V IDE O

COMP O NENT I N A UDI O

Comp one n t

INP UT

UPDAT

RESET

LAN

(SERVICE ONLY)

RGB IN

RGB(PC)

AUDIO

(RGB/DVI)

COMPONENT IN

VIDEO

AUDIO

(SE

Y L RP

Component Connection

1. How to connect

)

Connect the video outputs (Y, PB, PR

Match the jack colors (Y = green, P

jacks on the TV.

of the DVD to the

B = blue, and PR = red

Connect the audio outputs of the DVD to the

jacks on the TV.

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

input source on the TV using the

EXTERNAL EQUIPMENT SETUP

)

1 2

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

Video output ports

on DVD player

YPBP

B-Y

R-Y

EXTERNAL EQUIPMENT SETUP

HDMI /DVI I N

HDMI

INP UT

RGB IN

COM

VIDEO

HDMI/DVI IN

1(DVI)

RJP

INTERFACE

HDMI OUTPUT

HDMI Connection

1. How to connect

EXTERNAL EQUIPMENT SETUP

Connect the HDMI output of the DVD to the

No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

■

Select the

■

Refer to the DVD player's manual for operating instructions.

jack on the TV.

input source on the TV using the

button on the remote control.

+ 58 hidden pages