LG 32LG3DCUA User Manual

ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).

LCD TV
OWNER’S MANUAL

26LG3DC
26LC3DCH
32LG3DC
32LC3DCH

Please read this manual carefully before operating
your set.

Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.

As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the
ENERGY STAR guidelines
for energy efficiency.

P/NO : SAC30708026 (0801-REV00)

www.lgcommercial.com

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the litera­ture accompanying the appliance.

WARNING/CAUTION

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

1

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety

instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At the
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be
placed immediately adjacent to that safety instruction:

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

1

Clean only with dry cloth.

2

Do not block any ventilation openings. Install in

3

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

4

radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized

6

or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on

7

or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by

8

the manufacturer.

Unplug this apparatus when unused for long

9

periods of time.

When mounting a TV it on the wall, make sure

5

not to install TV by the hanging power and sig­nal cables on the back of the TV.

2

Use only with the cart, stand, tripod, bracket,

10

or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.

Never touch this apparatus or antenna during

11

a thunder or lighting storm.

Do not allow a impact shock or any objects to

12

fall into the product, and do not drop onto the
screen with something.

Refer all servicing to qualified service personnel.

13

Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has exposed to rain or moisture,
does not operate normally, or has been
dropped.

of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Outdoor use marking :

15

WARNING - To reduce the risk of fire or elec­tric shock, do not expose this appliance to rain
or moisture.

Wet Location Marking : Apparatus shall not be

16

exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.

CAUTION concerning the Power Cord :

14

Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates dam­age or deterioration, unplug it, discontinue use

GROUNDING

17

Ensure that you connect the earth ground wire
to prevent possible electric shock. If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.

Short-circuit

Breaker

DISCON N E C T I N G DEVICE FROM MAINS

18

Mains plug is the disconnecting device. The
plug must remain readily operable.

Power
Supply

3

CONTENTS

WARNING / CAUTION

SAFETY INSTRUCTIONS

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . . . . . . . . . . . . . . . . . . . . . . . . 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front Panel Information
Back Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Desktop Pedestal Installation
Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Protection Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Securing the TV to the wall to prevent falling

. . . . 14

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 15

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

VCR Setup
Other A/V Source Setup
PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PICTURE CONTROL

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 40

Preset Picture Settings

- Picture Mode - Preset

- Color Tone - Preset

Manual Picture Adjustment

- Picture Mode - User Mode

- Picture Mode - Expert Control

Picture Improvement Technology

Advanced Control - Black (Darkness) Level

Advanced Control - Real Cinema

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

. . . . . . . . . . . . . . . . . . . . . . . . 44

. . . . . . . . . . . . . . . . . . 45

. . . . . . . . . . . . . . . . . . . . . 46

. . . . . . . 47

. . . . . . . . . . . . . . . . . . . . . . 48

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Channel Setup

- Auto Scan (Auto Tuning)

- Add / Delete Channel (Manual Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 34

. . . . . . 35

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Channel Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4

SOUND & LANGUAGE CONTROL

APPENDIX

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 50

Clear Voice

Preset Sound Setting (Sound Mode)

Sound Setting Adjustment - User Mode

Balance

TV Speakers On/Off Setup

Audio Reset

Stereo/SAP Broadcasts Setup

Audio Language

On-Screen Menus Language Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

. . . . . . . . . . . . . . . . 52

. . . . . . . . . . . 53

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

. . . . . . . . . . . . . . . . . . . . . . . . . . 57

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

. . . . . . . . . . . . . . 59

Caption Mode

- Analog Broadcasting System Captions

- Digital Broadcasting System Captions

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

. . . . . . . 60

. . . . . . . . 61

TIME SETTING

Clock Setting

- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

- Manual Clock Setup

Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Sleep Timer Setting

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Maintenance
Product Specifications
IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Channel Blocking
Movie & TV Rating

Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

5

FEATURE OF THIS TV

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

6

PREPARATION

Copyright© 2007 LGE,
All Rights Reserved.

1.5V 1.5V

123

456

78

0-

9

VO

L

CH

E

NT

E

R

PO

W

E

R

MUTE

MENU

A

D
J

U
S

T

R
E

T
U

R
N

CC

SAP

FL
A

SHBK

PI
C

T
UR

E

S
O

U
N

D

R

A

T
IO

T
V

I
N

P
U

T

T

IM

E
R

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

PREPARATION

Owner’s Manual Power Cord

CD Manual

Remote Control,

Batteries

x 4 x 4

Bolts for stand assembly

(Refer to P.14)

* Wipe spots on the exterior only with the polishing cloth.

Polishing Cloth

(This feature is not available

for all models.)

* Do not wipe roughly when removing stain. Please be

75ohm Round Cable

cautions of that excessive pressure may cause scratch or
discoloration.

Screw for stand fixing

(Refer to P.18)

Option Extras

When using the VGA (D-sub 15 pin cable)
PC connection, the user must use shielded
signal interface cables with ferrite cores to
maintain standards compliance.

D-sub 15 pin Cable

Protection Cover

(Refer to P.20)

7

PREPARATION

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

■

PREPARATION

NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using

the OPTION menu.

Remote Control Sensor

POWER Button

Po w er Ind i cator

p.85

)

G

CH

VOL

ENTER

CHANNEL(+, -)
Buttons

VOLUME (+, -)
Buttons

ENTER Button

in

MENU

MENU Button

INPUT

INPUT Button

8

BACK PANEL INFORMATION

AUDIO IN
(RGB/DVI)

VIDEO

AUDIO

HDMI/DVI IN

USB IN

SERVUCE ONLY

AV IN 1

VIDEO

MONO

( )

AUDIO

S-VIDEO

COMPONENT

IN

RGB IN (PC)

RESET

UPDATE

RS-232C IN

(SERVICE ONLY)

REMOTE

CONTROL OUT

SPEAKER OUT

8

AV IN 2

L/MONO

R

AUDIO

VIDEO

H/P

■

Image shown may differ from your TV.

12

PREPARATION

11

1

3

2

1

7

1

AV (Audio/Video) IN

Connect audio/video output from an external
device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

2

HDMI/DVI IN

Digital Connection. Supports HD video and Digital
audio. Doesn’t support 480i.

Accepts DVI video using an adapter or HDMI to
DVI cable (not included)

USB IN SERVICE ONLY

3

Used for software updates.

4

UPDATE / RESET

RS-232C IN (SERVICE ONLY)

5

Used by third party devices.

6

RGB IN (PC)

Connect the output from a PC. Connect over-the
air signals to this jack.

4

5

6

9

8

10

Connect cable signals to this jack.

7

COMPONENT IN

Connect a component video/audio device to
these jacks.

AUDIO IN (RGB/DVI)

8

Connect the audio from a PC or DTV.

9

REMOTE CONTROL OUT

10

SPEAKER OUT 8

11

H/P

Plug the headphone into the headphone socket.

12

Power Cord Socket

Ω

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

9

PREPARATION

STAND INSTALLATION (Only 42PG10/20/20C)

■

Image shown may differ from your TV.

PREPARATION

Carefully place the TV screen side down on a

1

cushioned surface to protect the screen from
damage.

Assemble the parts of the

2

3

4

COVER BASE

with
as shown.

Assemble the TV as shown.

Fix the 4 bolts securely using the holes in the
back of the TV.

of the TV.Assemble the TV

STAND B O D Y

STAND B O D Y

COVER BASE

10

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.

1

To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as

2

shown.

PREPARATION

Put the cables inside the CABLE MANAGEMENT

3

CLIP and snap it closed.

CABLE MANAGEMENT CLIP

11

PREPARATION

DESKTOP PEDESTAL INSTALLATION

■

Image shown may differ from your TV.

PREPARATION

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

4 inches

4 inches

CAUTION

4 inches

Ensure adequate ventilation by following the clearance recommendations.

G

4 inches

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product. Use only an attached screw.

12

Stand

1-Screw

(provided as parts of the product)

Desk

WARNING

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation

G

instructions. Tipping, shaking, or rocking the machine may cause injury.

VESA WALL MOUNTING

!

This TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV. These
mounts are sold by third parties and not available from LG. Refer to the instructions included with the
mount for more info.

200 mm

100 mm

NOTE

Screw length needed depends on the wall mount used. For further information, refer to the instructions

G

included with the mount.

PREPARATION

PROTECTION COVER

■

Image shown may differ from your TV.

You can remove the stand before installing the TV on a
wall mount by performing the previous stand instruc­tions in reverse. After removing the stand, install the
included
stand.

Insert the
clicking sound.

protecti o n cover

PR O TECTI O N COVER

over the hole for the

into the TV until

13

PREPARATION

!

SECURING THE TV TO THE WALL TO PREVENT FALLING

■

PREPARATION

You should purchase necessary components to prevent TV from falling off of the stand.

■

Image shown may differ from your TV.

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately)
to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (not provided as parts of the product, must pur­chase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.

NOTE

Use a platform or cabinet strong enough and large enough to support the size

G

and weight of the TV.
To use the TV safely, make sure that the height of the bracket on the wall and the

G

one on the TV are the same.

14

ANTENNA/

CABLE IN

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.

For optimum picture quality, adjust antenna direction if needed.

Wall

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Antenna
Socket

Outdoor

RF Coaxial Wire (75 ohm)

Antenna
(VHF, UHF)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

2. Cable

Cable TV
Wall Jack

RF Coaxial Wire (75 ohm)

Copper Wire

Be careful not to bend the copper wire
when connecting the antenna.

ANTENNA/

CABLE IN

PREPARATION

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA/
CABLE IN

Antenna

UHF

Signal
Amplifier

VHF

15

EXTERNAL EQUIPMENT SETUP

A(RAUDIO IN

(RGB/DVI)

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

RGBRGB IN (PC)

UPDATE

RS-2

(SERVI

RS-232C IN

(SERVICE ONLY)

AV IN 1AV IN 1

VIDEO

AUDIO

COMPONENT

IN

Y L RPBP

R

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

EXTERNAL EQUIPMENT SETUP

Component Connection

1. How to connect

Connect the video outputs (Y, PB, PR

1

top box to the
the TV. Match the jack colors (Y = green, P
P

Connect the audio output of the digital set-top box to

2

the

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

■

Select
button on the remote control.

Supported Resolutions

Signal

480i

480p

720 p

10 8 0 i

COMPONE N T IN VIDEO

R = red).

COMPONEN T IN A U D I O

Component

input source with using the

Component

Yes

Yes

Yes

Yes

)

of the digital set-

B = blue, and

jacks on the TV.

HDMI

No

Yes

Yes

Yes

jacks on

)

INPUT

Y, CB/PB, CR/PR

Resolution

720x480i

720x480p

1280x720p

1920x1080i

1

2

Horizontal Vertical

Frequency(KHz)Frequency(Hz

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

)

16

HDMI Connection

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

UPUPDATE

AV IN 1AV IN 1

VIDEO

AU

COMPONENT

IN

HDMI-DTV OUTPUT

1. How to connect

EXTERNAL EQUIPMENT SETUP

Connect the digital set-top box to

1

jack on the TV.

No separate audio connection is necessary.

2

HDMI supports both audio and video.

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

■

HDMI/DVI

Select

input source with using the

button on the remote control.

HDMI/ D V I I N

)

INPUT

HDMI-DTV

Resolution

720x480p

1280x720p

1920x1080i

1

Horizontal Vertical

Frequency(KHz)Frequency(Hz

31.469 59.94

31.500 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

)

1920x1080p

67.50 60.00

17

EXTERNAL EQUIPMENT SETUP

AUDIO IN

(RGB/DVI)

AUDIO IN

(RGB/DVI)

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

RGB IN (PC)RGB IN (PC)

RESET

UPDATE

RS-232C IN

(SERVICE ONLY)

RS-232C IN

(SERVICE ONLY)

AV IN 1AV IN 1

VIDEO

AUDIO

COMPONENT

IN

LR

DVI-DTV OUTPUT

L

R

!

DVI to HDMI Connection

EXTERNAL EQUIPMENT SETUP

Connect the DVI output of the digital set-top box to

1

the

Connect the audio output of the digital set-top box to

2

the

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s man­ual for the digital set-top box.

■

Select the

INPU T

NOTE

A DVI to HDMI cable or adapter is required for this

G

connection. DVI doesn't support audio, so a separate
audio connection is necessary.

1. How to connect

HDMI/DVI IN

AUDIO IN(RGB/DVI)

jack on the TV.

jack on the TV.

)

HDMI/DVI

input source on the TV using the

button on the remote control.

1

2

18

DVD SETUP

A(AUDIO IN

(RGB/DVI)

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

RGBRGB IN (PC)

UPDATE

RS-

(SERV

RS-232C IN

(SERVICE ONLY)

AV IN 1AV IN 1

VIDEO

AUDIO

COMPONENT

IN

Y L RPBP

R

Component Connection

1. How to connect

)

Connect the video outputs (Y, PB, PR

1

COMPONE N T IN V I D E O

jacks on the TV.

Match the jack colors (Y = green, P

Connect the audio outputs of the DVD to the

2

COMPONEN T IN A U D I O

jacks on the TV.

of the DVD to the

B = blue, and PR = red

)

.

1

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

INPUT

■

Refer to the DVD player's manual for operating instructions.

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component

input source on the TV using the

button on the remote control.

EXTERNAL EQUIPMENT SETUP

2

Component ports on the TV

Video output ports

on DVD player

YPB PR

B-Y

Cb

PB

R-Y

Pb

Y

Y

Y

Y

PR

Cr

Pr

19

EXTERNAL EQUIPMENT SETUP

L

R

S-VIDEO

AUDIO

VIDEO

MONO

( )

AUDIO

AV IN 1

AV IN 1

VIDEO

AUDIO

COMPONENT

IN

S-VIDEO

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

AV IN 1AV IN 1

VIDEO

AUDIO

COMPONENT

IN

HDMI-DTV OUTPUT

S-Video Connection

EXTERNAL EQUIPMENT SETUP

1. How to connect

Connect the S-VIDEO output of the DVD to the

1

S -VIDEO

Connect the audio outputs of the DVD to the

2

input jacks on the TV.

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the
button on the remote control.

■

If connected to

■

Refer to the DVD player's manual for operating instructions.

HDMI Connection

1. How to connect

Connect the HDMI output of the DVD to the

1

HDMI/DVI IN

input on the TV.

AV 1

input source on the TV using the

AV IN2

, select

AV2

input source on the TV.

jack on the TV.

AUDIO

INPUT

1

2

20

2

2. How to use

■

■

No separate audio connection is necessary.
HDMI supports both audio and video.

Select the

INPUT

HDMI/DVI

input source on the TV using the

button on the remote control.

Refer to the DVD player's manual for operating instructions.

1

VCR SETUP

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

ANTENNA IN

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on
the screen. This phenomenon is common to all TVs and is not covered by warranty.

Antenna Connection

1. How to connect

Connect the RF antenna out socket of the

1

VCR to the
TV.

Connect the antenna cable to the RF

2

antenna in socket of the VCR.

2. How to use

ANT E NNA IN

socket on the

Wall Jack

1

2

EXTERNAL EQUIPMENT SETUP

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s

)

manual.

Antenna

21

EXTERNAL EQUIPMENT SETUP

!

L R

S-VIDEO VIDEO

VIDEO

MONO

( )

AUDIO

RGRGB IN (PC)

AV IN 1

AV IN 1

VIDEO

AUDIO

COMPONENT

IN

S-VIDEO

A(RAUDIO IN

(RGB/DVI)

VIDEO

MONO

( )

AUDIO

RGBRGB IN (PC)

AV IN 1

AV IN 1

VIDEO

AUDIO

COMPONENT

IN

S-VIDEO

L

R

S-VIDEO VIDEO

!

Composite (RCA) Connection

1. How to connect

Connect the

1

VCR. Match the jack colors (Video = yellow, Audio Left

EXTERNAL EQUIPMENT SETUP

= white, and Audio Right = red)

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

■

Select the
button on the remote control.

■

If connected to

NOTE

If you have a mono VCR, connect the audio cable

G

from the VCR to the
TV.

S-Video Connection

1. How to connect

Connect the S-VIDEO output of the VCR to the

1

S -VIDEO

AUDIO/VIDEO

AV 1

input source on the TV using the

AV I N2

, select

AV2

AUDIO L/MONO

input on the TV.

jacks between TV and

1

)

INPUT

input source on the TV.

jack of the

22

2. How to use

Connect the audio outputs of the VCR to the

2

input jacks on the TV.

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

■

Select the

AV 1

input source on the TV using the

)

button on the remote control.

NOTE

S-Video provides better quality than composite. Use

G

it when available.

AUDIO

INPUT

1

2

CAUTION

Do not connect to both Video

G

and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.

OTHER A/V SOURCE SETUP

AV IN 2

L/ MONO

R

AUDIO

VIDEO

H/P

L R

VIDEO

1. How to connect

Camcorder

Video Game Set

Connect the

1

between TV and external equipment.
Match the jack colors
(

Video = yellow, Audio Left = white, and

Audio Right = red

AUDIO/VIDEO

.

)

2. How to use

■

Select the
the

■

If connected to
input source on the TV.

■

Operate the corresponding external equipment.

INPUT

AV 2

input source on the TV using

button on the remote control.

AV I N 1

input, select the

jacks

EXTERNAL EQUIPMENT SETUP

1

AV 1

23

EXTERNAL EQUIPMENT SETUP

RGB OUTPUT

AUDIO

AUDIO IN

(RGB/DVI)

AUDIO INAUDIO IN

(RGB/DVI)

USB IN

VIDEO

RGB IN (PC)RGB IN (PC)RGB IN (PC)

RESET

UPDATE

RS-232C IN

(SERVICE ONLY)

RS-232C IN

(SERVICE ONLY)

REMOTE

CONTROL OUT

REMOTE

CONTROL OUT

SSPEAKER OUT

AUDIOAUDIO

AUDIO IN

(RGB/DVI)

AUDIO IN

(RGB/DVI)

AUDIO IN

(RGB/DVI)

HDMI/DVI IN

USB IN

SERVUCE ONLY

VIDEO

MONO

( )

AUDIO

S-VIDEO

RGB IN (PC)

UPDATE

RS-232C IN

(SERVICE ONLY

RS-232C IN

(SERVICE ONLY)

CONTROL OUT

VIDEOVIDEO

AUDIOAUDIO

COMPONENT

IN

DVI-PC OUTPUT AUDIO

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

EXTERNAL EQUIPMENT SETUP

1. How to connect

Connect the VGA output of the PC to the

1

I N(P C

Connect the PC audio output to the

2

(

2. How to use

■

Turn on the PC and the TV.

■

Select the

INPUT

DVI to HDMI Connection

1. How to connect

)

jack on the TV.

RGB/DVI

)

RGB-PC

jack on the TV.

input source on the TV using the

button on the remote control.

RG B

AUD I O

1

2

24

Connect the DVI output of the PC to the

1

IN

jack on the TV.

Connect the PC audio output to the

2

(RGB/DVI)

2. How to use

■

Turn on the PC and the TV.

■

Select the

INPUT

button on the remote control.

jack on the TV.

HDMI/DVI

HDMI/DVI

AUDIO I N

input source on the TV using the

1

2

!

Supported Display Specifications
(RGB-PC, HDMI-PC)

Resolution

640x350

720x400

640x480

800x600

1024x768

1280x768

1360x768

1366x768

Horizontal Vertical

Frequency(KHz)Frequency(Hz

31.469 70.08

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.776 59.87

47.712 60.01

47.720 59.799

47.130 59.65

* Only RGB-PC mode

NOTES

To get the the best picture quality, adjust the

)

G

PC graphics card to 1360x768.

Depending on the graphics card, DOS mode

G

may not work if a HDMI to DVI Cable is in use.

In PC mode, there may be noise associated

G

with the resolution, vertical pattern, contrast
or brightness. If noise is present, change the
PC output to another resolution, change the
refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu
until the picture is clear.

Avoid keeping a fixed image on the screen for a

G

long period of time. The fixed image could
become permanently imprinted on the screen.

The synchronization input form for Horizontal

G

and Vertical frequencies is separate.

Depending on the graphics card, some resolu-

G

tion settings may not allow the image to be
positioned on the screen properly.

EXTERNAL EQUIPMENT SETUP

25