LG LCD TV, 42LD6 Series, 32LD6 Series, 37LD6 Series Owner's Manual
www.lg.com
OWNER’S MANUAL
LCD TV
Please read this manual carefully before operating
your set and retain it for future reference.
ENGLISH
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Separate purchase
Wall Mounting Bracket
(32LD6
***
)
LSW100B or
LSW100BG
(37/42LD6
***
)
LSW200B or
LSW200BG
I
CONTENTS
CONTENTS
PREPARATION
LCD TV Models : 32/37/42LD6
*** ...................A-1
EXTERNAL EQUIPMENT SETUP
Antenna Connection ............................................1
Connecting with a Component cable ..................2
Connecting with an HDMI cable .........................3
Connecting with an HDMI to DVI cable ..............4
Connecting with a Euro Scart cable ...................5
Usb setup ............................................................6
Connecting with AN RF Cable ............................6
Connecting with a D-sub 15 pin cable ................7
Speaker output Setup .........................................7
Insertion of A CI Module ......................................8
Headphone Setup ...............................................8
Digital audio out Setup ........................................9
Supported Display Resolution ...........................10
Screen Setup for PC mode ...............................12
Network setup ...................................................16
WATCHING TV / PROGRAMME CONTROL
Turning on the TV .............................................17
Initializing Setup ...............................................17
Programme Selection ........................................17
Volume Adjustment ...........................................17
Quick Menu .......................................................18
On Screen Menus Selection and adjustment ...19
Auto programme tuning ...................................21
Manual programme Tuning ...............................22
Programme Edit ...............................................26
Booster ..............................................................28
CI [Common Interface] Information ...................29
Selecting the Programme List ...........................30
Input List ............................................................31
Input Label ........................................................32
Data Service ......................................................33
SIMPLINK ..........................................................34
AV Mode ............................................................38
Initializing(Reset to original factory settings) ....39
TO USE A USB DEVICE
When connecting a USB device .......................40
Movie list ...........................................................42
Photo list ............................................................53
Music list ............................................................63
Extra Contents ..................................................72
DivX Registration Code .....................................73
Deactivation .......................................................74
EPG(ELECTRONIC PROGRAMME
GUIDE)(IN DIGITAL MODE)
Switch on/off EPG .............................................76
Select a programme ..........................................76
Button Function in NOW/NEXT Guide Mode ...76
Button Function in 8 Day Guide Mode .............77
Button Function in Date Change Mode ............78
Button Function in Extended Description Box ..78
PICTURE CONTROL
Picture Size (Aspect Ratio) Control ..................79
Picture Wizard ...................................................81
Energy Saving ...................................................82
Preset Picture Settings .....................................83
Manual Picture Adjustment ...............................84
Picture Improvement Technology ......................86
Expert Picture Control .......................................87
Picture Reset .....................................................90
Power Indicator .................................................91
II
CONTENTS
CONTENTS
SOUND & LANGUAGE CONTROL
Auto Volume Leveler .........................................92
Clear Voice II .....................................................93
Preset Sound Settings-Sound Mode ................94
Sound Setting Adjustment -User Mode ............95
Infinite Sound ....................................................95
Balance .............................................................96
DTV Audio Setting (in digital mode only) ..........97
Selecting Digital Audio out ................................98
Audio Reset .......................................................99
Audio Description (In digital mode only) .........100
I/II
Stereo/Dual Reception (In Analogue Mode Only) .101
NICAM Reception (In Analogue Mode Only) ..102
Speaker Sound Output Selection ...................102
On-Screen Menu Language / Country Selection ..103
Language Selection ........................................104
TIME SETTING
Clock Setup .....................................................106
Auto on/off time setting ...................................107
Sleep Timer setting .........................................108
Alarm setting ...................................................109
PARENTAL CONTROL / RATINGS
Set Password & Lock System.........................110
Block Programme ............................................111
Parental Control (In Digital Mode only) ...........112
External Input Blocking ...................................113
Key Lock..........................................................114
TELETEXT
Switch on/off ...................................................115
SIMPLE Text....................................................115
TOP Text..........................................................116
FASTEXT ........................................................116
Special Teletext Functions ..............................117
DIGITAL TELETEXT
Teletext within Digital Service .........................118
Teletext in Digital Service ................................118
APPENDIX
Troubleshooting ...............................................119
Maintenance ....................................................121
Product Specifications ...................................122
IR Codes .........................................................124
External Control Device Setup ........................125
Open source software notice ..........................132
A-1
PREPARATION
LCD TV MODELS : 32/37/42LD6
***
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please
contact the dealer where you purchased the TV.
■ Image shown may differ from your TV.
Owner’s Manual
Batteries
(AAA)
Remote Control
Polishing Cloth
Polishing cloth for
use on the screen.
This item is not included for all models.
* Lightly wipe any stains or
fingerprints on the surface
of the TV with the polishing cloth.
Do not use excessive
force. This may cause
scratching or discolouration.
AV MODE INPUT
ENERGY
SAVING
EXIT
OK
BACK
PORTAL
Q.MENU
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
[
9
wxyz
LIST
Q.VIEW
GUIDE
AD
ALARM
INFO
MARK
RATIO
MUTE
DELETE
CHAR/NUM
P
TV/
RAD
P
A
G
E
MENU
Ferrite Core
(
This item is not included
for all models.
)
Install the power plug closely.
Use of ferrite core (This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic
wave when connecting the power cord.
The closer the location of the ferrite core to the power
plug, the better it is.
Power Cord
1-screw for stand fixing
Protection cover
Bolts for stand assembly
(M4x20)
x 8
Protective Bracket and Bolt for Power Cord
(This feature is not available for all models.)
Cable Holder
Plug in type Holder
PREPARATION
A-2
PREPARATION
PREPARATION
FRONT PANEL CONTROLS
■ Image shown may differ from your TV.
NOTE
►TV can be placed in standby mode in order to reduce the power consumption. And TV should be
switched off using the power switch on the TV if it will not be watched for some time, as this will
reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of
brightness of the picture is reduced, and this will reduce the overall running cost.
CAUTION
► Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from frag-
ments of glass, or the TV may fall.
► Do not drag the TV. The floor or the product may be damaged.
SPEAKER
Power/Standby Indicator
(Can be adjusted using the Power
Indicator in the OPTION menu.)
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions.
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
A-3
PREPARATION
CABLE MANAGEMENT
AC IN
USB IN
USB IN
H/P
14
CABLE MANAGEMENT
AC IN
1
2
HDMI/DVI IN
(RGB)
LAN
USB IN
H/P
SPEAKER
OUT
VOLUME CONTROL
STEREO (8 )
8
11
7
1
9 10
ANTENNA IN
12
BACK PANEL INFORMATION
■ Image shown may differ from your TV.
Power Cord Socket
This TV operates on an AC power. The voltage is indicated on the Specifications page.
(► p.122 to 123) Never attempt to operate
the TV on DC power.
Antenna Input
Connect antenna or cable to this jack.
LAN
Network connection.
Also used for video, photo and music files on
a local network.
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
Component Input
Connect a component video/audio device to
these jacks.
Euro Scart Socket (AV1)
Connect scart socket input or output from an
external device to these jacks.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI
(VIDEO) signal to HDMI/DVI port with DVI to
HDMI cable.
RGB IN Input
Connect the output from a PC.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
SPEAKER OUTPUT(STEREO)
The phone socket for external speaker is on
this jack.
USB Input
Connect USB storage device to this jack.
PCMCIA (Personal Computer Memory
Card International Association) Card Slot
Insert the CI Module to PCMCIA CARD
SLOT.
(This feature is not available in all countries.)
Headphone Socket
Plug the headphone into the headphone
socket.
1
2
3
4
5
6
8
9
10
11
12
13
14
7
2
43
5
6
13
A-4
PREPARATION
PREPARATION
STAND INSTALLATION
Fix the 4 bolts securely using the holes in
the back of the TV.
■ Image shown may differ from your TV.
When assembling the desk type stand, check whether the bolt is fully tightened.
(If not tightened fully, the product can tilt forward after the product installation.)
If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening
part of the bolt.
4
Carefully place the TV screen side down
on a cushioned surface to protect the
screen from damage.
Assemble the TV as shown.
1
3
Assemble the parts of the Stand Body with
the Stand Base of the TV.
2
Stand Body
Stand Base
Tighten the stand with the
four screws (provided as
parts of the TV).
x 4
M4 X 20
A-5
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■ Image shown may differ from your TV.
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the Protective
Bracket/Bolt or the Plug in type Holder. It
will help prevent the power cable from being
removed by accident.
AC IN
AC IN
Protective Bracket/Bolt
( This feature is not available
for all models.)
Plug in type Holder
AC IN
or
AC IN
AC IN
AC IN
Install the Cable Management Clip as
shown.
If your TV has the Cable Holder, install
it as shown and bundle the cables.
Cable Management Clip
AC IN
AC IN
Cable Holder
2
Put the cables inside the Cable
Management Clip and snap it closed.
3
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
AC IN
►Do not hold the Cable Management Clip
when moving the TV.
- If the TV is dropped, you may be injured or
the product may be broken.
►With some TVs, the Plug in type Holder
and the Cable Holder are included. If these
holders are inserted into the hole provided
on back of the TV, they cannot be removed.
NOTE
A-6
PREPARATION
PREPARATION
SWIVEL STAND
■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set
manually to the left or right direction by 20
degrees to suit your viewing position.
ATTACHING THE TV TO A
DESK
Desk
Stand
■ Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the product.
WARNING
►To prevent TV from falling over, the TV
should be securely attached to the floor/wall
per installation instructions. Tipping, shaking,
or rocking the machine may cause injury.
►Screws: M5 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
1-Screw ( provided as parts of the product)
■ Image shown may differ from your TV.
When installing the wall-mounted unit, use the
protection cover.
Insert the Protection Cover into the TV until
clicking sound.
NOT USING THE
DESK-TYPE STAND
Protection Cover
4-Screws
(not provided as parts of the product)
Desk
Stand
A-7
PREPARATION
■ This feature is not available for all models.
■ Image shown may differ from your TV.
KENSINGTON SECURITY
SYSTEM
CAREFUL INSTALLATION
ADVICE
■ You should purchase necessary components
to fix the TV safety and secure to the wall on
the market.
■ Position the TV close to the wall to avoid the
possibility of it falling when pushed.
■ The instructions shown below are a safer way
to set up the TV, by fixing it to the wall, avoiding the possibility of it falling forwards if pulled.
This will prevent the TV from falling forward
and causing injury. This will also prevent the
TV from damage. Ensure that children do not
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the
wall. Match the height of the bracket that is
mounted on the wall.
Use a sturdy rope to tie the product for alignment. It is safer to tie the rope so it becomes
horizontal between the wall and the product.
2
2
1
1
The TV is equipped with a Kensington Security
System connector on the back panel. Connect
the Kensington Security System cable as shown
below.
For the detailed installation and use of the
Kensington Security System, refer to the user’s
guide provided with the Kensington Security
System.
For further information, contact http://www.kensington.com, the internet homepage of the
Kensington
company. Kensington sells security systems for
expensive electronic equipment such as notebook PCs and LCD projectors.
1
2
3
NOTE
► When moving the TV undo the cords first.
► Use a platform or cabinet strong and large
enough to support the size and weight of the TV.
► To use the TV safely make sure that the height of
the bracket on the wall and on the TV is the
same.
NOTE
► The Kensington Security System is an optional
accessory.
► If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on.
This is normal
, there is nothing wrong with TV.
► Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
► Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortio
n
effects on the screen.
A-8
PREPARATION
PREPARATION
■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■ The TV is designed to be mounted horizontally.
Power
Supply
Circuit
breaker
EARTHING
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
WALL MOUNT: HORIZONTAL
INSTALLATION
■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■ We recommend that you purchase a wall mounting bracket which supports VESA standard.
■ LG recommends that wall mounting be performed by a qualified professional installer.
DESKTOP PEDESTAL
INSTALLATION
Model
VESA
(A * B)
Standard
Screw
Quantity
32LD6
***
37/42LD6
***
200 * 100
200 * 200
M4
M6
4
4
10 cm
10 cm
10 cm
10 cm
NOTE
►Should Install wall mount on a solid wall per-
pendicular to the floor.
►Should use a special wall mount, if you want
to install it to ceiling or slanted wall.
►The surface that wall mount is to be mount-
ed on should be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.
►Installing screw type and length depends on
the wall mount used. Further information,
refer to the instructions included with the
mount.
►LG is not liable for any accidents or damage
to property or TV due to incorrect installation:
- Where a non-compliant VESA wall mount
is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause personal injury.
- Not following the recommended Installation
method.
10 cm
For adequate ventilation allow a clearance of 10
cm all around the TV.
10 cm
10 cm
10 cm
■ Image shown may differ from your TV.
A-9
PREPARATION
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
AV MODE INPUTENERGY
SAVING
EXIT
OK
BACK
PORTAL
Q.MENU
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
[
9
wxyz
LIST
Q.VIEW
GUIDE
AD
ALARM
INFO
MARK
RATIO
MUTE
DELETE
CHAR/NUM
P
TV/
RAD
P
A
G
E
MENU
(POWER)
ENERGY
SAVING
AV MODE
INPUT
TV/RAD
Switches the TV on from standby or off to standby.
Adjust the Energy Saving mode of the TV.(► p.82)
It helps you select and set images and sounds
when connecting AV devices.(► p.38)
External input mode rotate in regular sequence.
(
►
p.31)
Selects Radio, TV and DTV programme.
Shows programme guide. (►
p.75)
Displays and removes the hotel interactive menu.
Shows the present screen information.
Allows you to navigate the on-screen menus and
adjust the system settings to your preference.
Accepts your selection or displays the current
mode.
Selects a menu.
Clears all on-screen displays and returns to TV
viewing from any menu.(►
p.19)
Allows the user to move return one step in an interactive application, EPG or other user interaction
function.
Clears all on-screen displays and returns to TV
viewing from any menu.
GUIDE
PORTAL
INFO i
THUMBSTICK
(Up/Down/Left/Right)
OK
MENU
BACK
EXIT
Q. MENU
AD
ALARM
Select the desired quick menu source. (Aspect
Ratio, Clear Voice II , Picture Mode, Sound Mode,
Audio (or
Audio Language)
, Sleep Timer, Skip Off/
On, USB Device).(►
p.18)
Switches the Audio Description On or Off.
Sets the alarm function.
A-10
PREPARATION
PREPARATION
AV MODE INPUTENERGY
SAVING
EXIT
OK
BACK
PORTAL
Q.MENU
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
[
9
wxyz
LIST
Q.VIEW
GUIDE
AD
ALARM
INFO
MARK
RATIO
MUTE
DELETE
CHAR/NUM
P
TV/
RAD
P
A
G
E
MENU
1
TELETEXT
BUTTONS
SUBTITLE
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
(► p.115)
Recalls your preferred subtitle in digital mode.
1
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu
appears at the screen.(► p.34)
Coloured
buttons
These buttons are used for teletext (on TELETEXT
models only), Programme edit.
0 to 9 number
button
(Space)
LIST
Q.VIEW
Selects a programme.
Selects numbered items in a menu.
Opens an empty space on the screen keyboard.
Displays the programme table. (►
p.30)
Returns to the previously viewed programme.
]
A-11
PREPARATION
AV MODE INPUTENERGY
SAVING
EXIT
OK
BACK
PORTAL
Q.MENU
1
.,;@
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
0
[
9
wxyz
LIST
Q.VIEW
GUIDE
AD
ALARM
INFO
MARK
RATIO
MUTE
DELETE
CHAR/NUM
P
TV/
RAD
P
A
G
E
MENU
Installing Batteries
■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones.
■ Close cover.
■ To remove the batteries, perform the installation actions in
reverse.
SIMPLINK /
MY MEDIA
Menu
control buttons
Controls SIMPLINK or MY MEDIA menu (Photo List,
Music List and Movie List).
VOLUME UP
/DOWN
CHAR/NUM
MARK
RATIO
DELETE
MUTE
Programme
UP/DOWN
PAGE UP/
DOWN
Adjusts the volume.
Shifts the Character or Number.
Select the input to apply the Picture Wizard
settings.
Check and un-check programmes in the USB
menu.
Selects your desired Aspect Ratio of picture.
(► p.79)
Deletes the entered character when entering the
character on the screen keyboard.
Switches the sound on or off.
Selects a programme.
Move from one full set of screen information to the
next one.
1
EXTERNAL EQUIPMENT SETUP
ANTENNA IN
EXTERNAL EQUIPMENT SETUP
ANTENNA CONNECTION
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■ To prevent damage do not connect to the mains outlet until all connections are made between the
devices.
Antenna
UHF
Signal
Amplifier
VHF
■ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier
to the antenna as shown above.
■ If signal needs to be split for two TVs, use an antenna signal splitter for connection.
CABLE MANAGEMENT
AC IN
USB IN
H/P
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
(VHF, UHF)
Wall
Antenna
Socket
RF Coaxial Wire (75 Ω)
ANTENNA IN
2
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A COMPONENT CABLE
■ To avoid damaging any equipment, never plug in any power cord until you have finished connecting
all equipment.
■ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 32/37/42LD6
***
models.
■ Image shown may differ from your TV.
This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do
receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as
shown below.
► HDMI Audio Supported format : Dolby Digital, PCM.
DTS Audio format is not supported.
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Signal Component HDMI
480i/576i O X
480p/576p O O
720p/1080i O O
1080p
O
(50 Hz / 60 Hz only)
O
(24 Hz / 30 Hz /
50 Hz / 60 Hz)
Component ports on the TV Y PB PR
Video output ports
on DVD player
Y PB PR
Y B-Y R-Y
Y Cb Cr
Y Pb Pr
1
Connect the video outputs (Y, PB, PR) of the
external equipment (digital set-top box, DVD,
etc.) to the COMPONENT IN VIDEO jacks on
the TV.
2
Connect the audio output of the external equipment (digital set-top box, DVD, etc.) to the
COMPONENT IN AUDIO jacks on the TV.
3
Turn on the external equipment.
(
Refer to the external equipment's manual for
operating instructions.)
4
Select the Component input source using the
INPUT button on the remote control.
1
2
HDMI/DVI IN
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
RJP
INTERFACE
STEREO (8 )
1
2
3
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI CABLE
NOTE
►The TV can receive video and audio signals simultaneously
when using an HDMI cable.
►If the DVD does not support Auto HDMI, you must set the
output resolution appropriately.
►Check that your HDMI cable is High Speed HDMI Cable. If
the HDMI cables are not High Speed HDMI Cable, flickering
or no screen display can result. Please use the High Speed
HDMI Cable.
1
Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1, HDMI/DVI IN 2 jack on
the TV.
2
Turn on the external equipment.
(Refer to the external equipment's manual for operating
instructions.)
3
Select HDMI1, HDMI2 input source using the INPUT button on
the remote control.
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
RJP
INTERFACE
STEREO (8 )
1
2
HDMI/DVI IN
1
4
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH AN HDMI TO DVI CABLE
1
Connect the digital set-top box or the DVI output of the PC to HDMI/DVI IN 1 or HDMI/DVI
IN 2 jack on the TV.
2
Connect the audio output of the digital set-top
box or the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the digital set-top box or the PC and
the TV.
(
Refer to the digital set-top box or the PC
manual for operating instructions.)
4
Select HDMI1 or HDMI2 input source using the
INPUT button on the remote control.
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
STEREO (8 )
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
RJP
INTERFACE
STEREO (8 )
1
2
HDMI/DVI IN
1
2
HDMI/DVI IN
1 2
or
5
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A EURO SCART CABLE
Scart
Input Output
Video Audio RGB Video, Audio
AV1
O O O
Analogue TV, Digital TV
NOTE
► Any Euro scart cable used must be signal shielded.
► TV Out : Outputs Analogue TV
or Digital TV signals.
1
Connect the Euro scart socket of the external
equipment (DVD, VCR, etc.) to the AV1 Euro
scart socket on the TV.
2
Turn on the external equipment.
(Refer to the external equipment's manual for
operating instructions.)
3
Select AV1 input source using the INPUT button on the remote control.
N
SPEAKER
OUT
VOLUME CONTROL
STEREO (8 )
(RGB)
1
Output Type
Current
input mode
AV1
(TV Out)
AV1
(When DTV scheduled recording is in
progress using recording equipment.)
Digital TV Digital TV
O
Analogue TV, AV Analogue TV
O
(The input mode is converted to DTV.)
Component/RGB Analogue TV
HDMI X X
6
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
USB SETUP
1
Connect the USB device to the USB IN jack
on the TV.
2
After connecting the USB IN jack, you use the
USB function. (► p.40)
CONNECTING WITH AN RF CABLE
To avoid picture noise (interference), allow adequate distance between the VCR and TV.
1
Connect the ANT OUT socket of the VCR to
the ANTENNA IN socket on the TV.
2
Connect the antenna cable to the ANT IN
socket of the VCR.
3
Press the PLAY button on the VCR and match
the appropriate channel between the TV and
VCR for viewing.
ANTENNA IN
Wall Jack
Antenna
1
2
USB IN
1
or
7
EXTERNAL EQUIPMENT SETUP
CONNECTING WITH A D-SUB 15 PIN CABLE
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
1
Connect the RGB output of the PC to the RGB
IN (PC) jack on the TV.
2
Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV.
3
Turn on the PC and the TV
4
Select RGB input source using the INPUT button on the remote control.
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
RJP
INTERFACE
STEREO (8 )
1
2
HDMI/DVI IN
WIRELESS
CONTROL
2 1
SPEAKER OUTPUT SETUP
Connect the external speaker to the SPEAKER
OUTPUT(STEREO) jack on the TV.
1
1
1
Method of Volume control port
Cable
Spec.
GND / Up / Down
• Each Up/ Down pin is
pulled to 3.3V with CPU
GPIO.
• CPU detects transition
from 3.3V to GND level for
volume control.
8
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
USB IN
H/P
HEADPHONE SETUP
You can listen the sound through the headphone.
NOTE
► AUDIO menu items are disabled when connecting a headphone.
► When changing AV MODE with a headphone connected, the change is applied to video but not to audio.
► Optical Digital Audio Out is not available when connecting a headphone.
►Headphone impedance: 16 Ω
►Max audio output of headphone: 10 mW to 15 mW
1
Plug the headphone into the headphone socket.
2
To adjust the headphone volume, press the
+ or - button. If you press the MUTE button,
the sound from the headphone is switched off.
INSERTION OF A CI MODULE
To view the encrypted (pay) services in digital TV mode.
This feature is not available in all countries.
NOTE
► Check if the CI module is inserted into the PCMCIA card slot
in the right direction. If the module is not inserted properly,
this can cause damage to the TV and the PCMCIA card slot.
1
Insert the CI Module to PCMCIA (Personal
Computer Memory Card International
Association) CARD SLOT of TV as shown.
For further information, see p.29.
USB IN
USB IN
Check this point as
shown and insert the CI
Module.
9
EXTERNAL EQUIPMENT SETUP
DIGITAL AUDIO OUT SETUP
Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL
DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
CAUTION
► Do not look into the optical output port. Looking at the laser
beam may damage your vision.
1
Connect one end of an optical cable to the TV
Digital Audio (Optical) Output port.
2
Connect the other end of the optical cable to
the digital audio (Optical) input on the audio
equipment.
3
Refer to the external audio equipment instruction manual for operation.
(RGB)
LAN
SPEAKER
OUT
VOLUME CONTROL
RJP
INTERFACE
STEREO (8 )
1
2
10
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
SUPPORTED DISPLAY RESOLUTION
RGB-PC, HDMI/DVI-PC mode
HDMI/DVI-DTV mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
720x400 31.468 70.08
640x480 31.469 59.94
800x600 37.879 60.31
1024x768 48.363 60.00
1280x768 47.78 59.87
1360x768 47.72 59.80
1280x1024 63.595 60.00
1920x1080
(RGB-PC)
66.587 59.93
1920x1080
(HDMI-PC)
67.5 60.00
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
720x480
31.469
31.5
59.94
60
720x576 31.25 50
1280x720
37.5
44.96
45
50
59.94
60
1920x1080
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
11
EXTERNAL EQUIPMENT SETUP
NOTE
► Avoid keeping a fixed image on the set’s screen
for prolonged periods of time. The fixed image
may become permanently imprinted on the
screen; use a screen saver when possible.
► There may be interference relating to resolution,
vertical pattern, contrast or brightness in PC
mode. Change the PC mode to another resolution
or change the refresh rate to another rate or
adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of
the PC graphic card.
► The synchronization input waveform for Horizontal
and Vertical frequencies are separate.
► We recommend using 1360x768, 60 Hz(Only
32LD6
***
), 1920x1080, 60 Hz(Only 37/42LD6
***
)
for the PC mode, this should provide the best picture quality.
► Connect the signal cable from the monitor output
port of the PC to the RGB (PC) port of the TV or
the signal cable from the HDMI output port of the
PC to the HDMI IN (or HDMI/DVI IN) port on the
TV.
► Connect the audio cable from the PC to the Audio
input on the TV. (Audio cables are not included with
the TV).
► If using a sound card, adjust PC sound as required.
► If the graphic card on the PC does not output ana-
logue and digital RGB simultaneously, connect only
one of either RGB or HDMI IN (or HDMI/DVI IN) to
display the PC output on the TV.
► If the graphic card on the PC does output analogue
and digital RGB simultaneously, set the TV to either
RGB or HDMI; (the other mode is set to Plug and
Play automatically by the TV.)
► DOS mode may not work depending on the video
card if you use an HDMI to DVI cable.
► If you use too long an RGB-PC cable, there may be
interference on the screen. We recommend using
under 5m of cable. This provides the best picture
quality.
12
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
SCREEN SETUP FOR PC MODE
Returns Position, Size and Phase to the factory default settings.
This function works in the following mode : RGB[PC].
Screen Reset
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
1
Select PICTURE.
2
Select Screen.
3
Select Reset.
4
Select Yes.
5
Run Reset.
MENU
To Set
Auto Config.
SCREEN
Move
Prev.
Resolution
Position
Size
Phase
Reset
Yes No
OK
Move
PICTURE
• Brightness 50
• Sharpness 70
• Colour 60
• Tint 0
• Colour Temp. 0
• Advanced Control
• Picture Reset
• Screen
R G
W
C
►
• Screen
13
EXTERNAL EQUIPMENT SETUP
Automatically adjusts the picture position and minimizes image instability. After adjustment, if the
image is still not correct, your TV is functioning properly but needs further adjustment.
Auto configure
This function is for automatic adjustment of the screen position, size, and phase The displayed image
will be unstable for a few seconds while the auto configuration is in progress.
Auto Configure (RGB [PC] mode only)
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
• If the position of the image is still not correct,
try Auto adjustment again.
• If picture needs to be adjusted again after
Auto adjustment in RGB (PC), you can adjust
the Position, Size or Phase.
1
Select PICTURE.
2
Select Screen.
3
Select Auto Config..
4
Select Yes.
5
Run Auto Config..
MENU
Auto Config.
Auto Config.
SCREEN
Move
Prev.
Resolution
Position
Size
Phase
Reset
Yes No
OK
Move
PICTURE
►
• Brightness 50
• Sharpness 70
• Colour 60
• Tint 0
• Colour Temp. 0
• Advanced Control
• Picture Reset
• Screen
R G
W
C
• Screen
14
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
To view a normal picture, match the resolution of RGB mode and selection of PC mode.
This function works in the following mode: RGB[PC]
Selecting Resolution
• Press the MENU/EXIT button to return to normal TV viewing.
• Press the BACK button to move to the previous menu screen.
1
Select PICTURE.
2
Select Screen.
3
Select Resolution.
4
Select the desired resolution.
5
MENU
Auto Config.
SCREEN
Move
Prev.
Resolution
Position
Size
Phase
Reset
OK
Move
PICTURE
1024 x 768
1280 x 768
1360 x 768
►
• Brightness 50
• Sharpness 70
• Colour 60
• Tint 0
• Colour Temp. 0
• Advanced Control
• Picture Reset
• Screen
R G
W
C
• Screen
Loading...