OWNER’S MANUAL
Colour Television
Please read this manual carefully before operating your set. Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number |
: |
Serial number |
: |
P/NO.: MFL66681102-EN (CW91A)(1101-REV01) |
www.lg.com |
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and power plug.
Press the POWER button on the front panel or side panel to turn off the TV when the TV set is not being used for a long time.It is recommended to remove the plug from the wall outlet(Power point).
Disconnecting device from mains
Mains plug is the disconnecting device. The plug must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture.
Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.
Service
Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
Connection of external equipment
Aerial socket
1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel on a desired programme number using the ‘Auto programme tuning’ section.
4.Select the programme number where the VCR channel is stored.
5.Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
Euro scart socket (option)
1.Connect the Euro scart socket of the VCR to the Euro scart socket of the set.
2.Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when connected to Euro scart socket, the set will switch to AV 1 mode automatically. But if you want to keep on watching TV mode, press the D / E or NUMBER buttons.Otherwise press
the TV/AV button on the remote control handset to select AV 1 The VCR playback picture appears on the screen.
You can also record programmes received by the TV on video tape.
1.Connect the audio/video out sockets of the VCR Note : Signal type RGB, i.e. the signals red, green to audio/video in sockets of the set and in sock- and blue can only be selected for the Euro scart ets of the VCR to RF OUT sockets of the set. socket. These signals are transmitted, for exam-
2.If the VCR is connected to the AV sockets on the ple, by a pay TV decoder, game machine or photo
set, press the TV/AV button to select AV1 or AV2(option).
3.Press the PLAY button on the VCR.The VCR playback picture appears on the screen.
You can also record programmes received by the TV on video tape via audio/video out sockets.
Note :
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set.
And if connected to AV2(option),then you should select L+L mode by pressing the I/II/*(option) key. If the VCRs are connected to AV2(option) and Side AV(option) at the same time,only the Side AV program will be displayed.
Side AV and Component can’t be used at the same time.
CD unit, etc.
Component in sockets (option)
1.Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
COMPONENT (480i) to the COMPONENT INPUT sockets (Y PB PR) on the set.
2.Connect the audio cable from the COMPONENT to AUDIO IN sockets of AV IN1 or AV IN2(option).
3.Press the TV/AV button to select COMPONENT.
4.Press the PLAY button on the COMPONENT. The COMPONENT playback picture appears on the screen.
2
Location and function of controls
Remote control handset
Before you use the remote control handset, please install the batteries.
1 |
|
|
2 |
9 |
|
Q.VIEW |
10 |
|
|
11 |
|
3 |
|
|
4 |
12 |
|
|
|
|
5 |
|
|
6 |
|
|
7 |
13 |
|
8 |
||
14 |
||
|
1.POWER
Switches the set on from standby or off to standby.
2.MUTE
Switches the sound on or off.
3.NUMBER BUTTONS
Switches the set on from standby or directly select a number.
USB SELECT BUTTONS
Oprate USB function.
4.MENU
To display on-screen or exit from USB mode . Other local key is not available in USB mode.
5.D / E (Programme Up/Down)
Selects a programme or a menu item. Switches the set on from standby.
F / G (Volume Up/Down)
Adjusts the volume. Adjusts menu settings.
OK
Accepts your selection or displays the current mode.
6.TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
7.SLEEP
Sets the sleep timer.
8.USB BUTTON
Select the USB mode.
9.TV/AV
Selects TV or AV mode. Switches the set on from standby. Exits the Teletext mode.
10.Q.VIEW (or YELLOW)
Returns to the previously viewed programme.
11.LIST/* (option)
Displays the programme table.
12. FAVOURITE/*(option)
Selects a favorite programme.
13. I/II/*(option)
Selects the language during dual language broacast.
Selects the sound output (option).
14. EYE/* (option)
Switches the eye function on or off.
* : No function COLOURED BUTTONS :
These buttons are used for teletext (only TELETEXT models) or programme edit.
Battery installation
The remote control handset is powered by AAA type batteries. Install batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.
Note :
To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
or
Front panel
MAIN POWER (ON/OFF) switches the set on or off.
POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby mode.dims when the set is switched on.
REMOTE CONTROL SENSOR
Note : Only use the supplied remote control handset. (When you use others, they will not be able to function.)
MENU
selects a menu.
A/OK
accepts your selection or displays the current mode.
F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.
D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
AUDIO/VIDEO IN SOCKETS (AV IN2)(option)
Connect the audio/video out sockets of external equipment to these sockets.
Note :AV2 on side panel is the same as AV2 on the back cover.
EYE (option)
adjusts picture according to the surrounding conditions.
Note :
What is shown here may be somewhat different from your set or can not be supplied on your area.
3
Basic operation
On and off
1.Press the main power button to switch the set on.
2.If the set is in standby mode, press the POWER, D / E, TV/AV or NUMBER buttons on the remote control handset to switch it on fully.
3.Press the POWER button on the remote control handset.
The set reverts to standby mode.
4.Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains plug is replaced in the mains power socket.
Mute function
Press the MUTE button. The sound is switched off
and the display W appears.
You can cancel it by pressing the MUTE, F / G,
I/II/*(option), button.
On screen language selection(option)
The menu can be displayed on the screen in desired language. First select your language.
1.Press the MENU button and then D / E button to select the Special menu.
2.Press the Gor OK button to select Language.
3.Press the F / G button to select your desired language.
All the on screen displays will appear in the selected language.Press the MENU button to return to the Special menu.
4.Repeatedly press the MENU button to return to normal TV viewing.
Other functions
TV and AV modes
AV mode is used when a video cassette recorder (VCR), or other equipment is connected to the set.
Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the ‘Connection of external equipment’ section.
AV1 : VCR connected to the Euro scart socket or AV IN 1 sockets on the set
AV2 : VCR connected to the AV IN 2 sockets on the set (option).
COMPONENT : DVD Player connected to the COMPONENT sockets on the set (option).
Alternatively you can select the TV or AV mode by pressing the TV/AV button.
In AV mode, to return to TV mode, press the D / E or NUMBER buttons.
Auto AV switching (option)
If your VCR outputs switching voltage when it is switched to playback with the VCR connected to the Euro scart socket. The set is automatically switched to AV1 mode when an AV signal is input. But if you want to keep on watching TV mode, press the D / E or NUMBER buttons. Press the TV/AV button to return to AV modes.
Child lock
The TV can be set so that the remote control handset is needed to control it. This feature can be used to prevent unauthorized viewing.
With the lock on, the display Child lock on appears on the screen if any button on the front panel is pressed while viewing the TV.
Degaussing (option)
Due to the super large Tube in the set. The colour purity of the picture may be affected by other magnetic influences such as speakers. Stripes may appear on the screen or there may be colour patches.
Note : If you cannot adjust the screen condition by degaussing, try it again after about 4 minutes.
Sleep timer
You don’t have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time elapses.
Repeatedly press the SLEEP button to select the number of minutes. The display - - - will appear on the screen, followed by 10, 20, 30, 60, 90, 120,
180 and 240. The timer begins to count down from the number of minutes selected.
Note :
a.To view the remaining sleep time, press the SLEEP button once.
b.To cancel the sleep time, repeatedly press the SLEEP button until the display - - - appears.
c.When you switch the set off, the set releases the preset sleep time.
4