LG 26LH1DC3, 26LH1DC4, 26LH1DC5 User Manual

Page 1

Please read this manual carefully before operating your set.

Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require

service.

Installation and Operating Guide

26LH1DC3

26LH1DC4

26LH1DC5

www.lgcommercial.com

Page 2

WARNING / CAUTION

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IT IS FORBIDDEN TO CONNECT THIS TV TO ANY TELECOMMUNICATION NETWORK / TELEPHONE.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THIS PRODUCT MUST BE USED WITH UL LISTED MOUNTING BRACKET.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

NOTE TO CABLE TV INSTALLER

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

THE PARTY RESPONSIBLE FOR PRODUCT

COMPLIANCE

(LG Electronics U.S.A., Inc.,)

(2000 Millbrook Drive)

(TELEPHONE NO:1-847-941-8000)

Page 3

Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

CAUTION

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall not be placed on the apparatus.

WARNING

THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

CAUTION

When used outside of the U.S., it may be used HAR cord with fitting of an approved agency is employed. (When used outside of U.S., other power supply cords may be used if the cord is approved by the local regulating agency.)

CAUTION

YOUR PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH YOUR SAFETY IN MIND. HOWEVER, IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO YOUR NEW PRODUCT, PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING YOUR NEW PRODUCT, AND SAVE THEM FOR FUTURE REFERENCE. OBSERVING THE SIMPLE PRECAUTIONS DISCUSSED IN THIS MANUAL CAN HELP YOU GET MANY YEARS OF ENJOYMENT AND SAFE OPERATION THAT ARE BUILT INTO YOUR NEW PRODUCT.

IMPORTANT SAFEGUARDS FOR YOU AND YOUR NEW PRODUCT

Clean the exterior of this television by removing dust with a lint-free cloth. CAUTION: To avoid damage to the surface of the television, do not use abrasive or chemical cleaning agents.

CLEANING AND DISINFECTION

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with the TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TVs performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

NOTE

Page 4

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Fo llow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 .Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 . Only use attachments/accessories specified by the manufacturer. 12 .Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 . Unplug this apparatus during lightning storms or when unused for long periods of time. 14 .Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps Power Service Grounding

Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC - National Electrical Code

PORTABLE CART WARNING

Page 5

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . 10

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Digital Audio Output

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Screen Setup for PC mode

. . . . . . . . . . . . . . . . . . . . . . . . . . 21

DV I Hookup To RJP or DVD Player . . . . . . . . . . . . . . . 22

Computer PC Hookup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

EXTERNAL EQUIPMENT SETUP

User Remote Control Button Functions . . . . . . . . . 23

Installer Remote Control Button Functions . . . . 24

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . 25

Channel Search

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

WATCHING TV /CHANNEL CONTROL

Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Daylight Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Time Zone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TV Activation Time Settings

. . . . . . . . . . . . . . . . . . . 33

TV Deactivation Time Settings

. . . . . . . . . . . . . . . 33

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

TIME SETTING

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . 4

CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PREPARATION

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Movie & TV Ratings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PARENTAL CONTROL/RATINGS

Caption / Text

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Preset Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Sound Setting Adjustment-user Mode . . . . . 43

Sound Balance Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Digital Audio Output Settings . . . . . . . . . . . . . 44

Aautomatic Volume Control Settings . . . . 45

Analog Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . 45

Digital Audio Language Settings . . . . . . . . . . . . 46

Using External Speakers . . . . . . . . . . . . . . . . . . . . . . 46

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Menu Transparency Settings . . . . . . . . . . . . . . . . . . 48

Set ID

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

SOUND & LANGUAGE CONTROL

Preset Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Screen Format Adjustments . . . . . . . . . . . . . . . . . 50

Noise Reduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Film Mode Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

PICTURE CONTROL

Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Cloning Procedure Troubleshooting

. . . . . . . . . . . . . . .71

Clone Troubleshooting Flow Chart . . . . . . . . . . . . . . . .73

TV Operating Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Installer Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . 76

APPENDIX

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Commercial Mode Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Cloning Connections/Learning Setup . . . . . . . . . . . . .54

Clone Programmer/Learning Setup

. . . . . . . . . . . . . . .55

Cloning Connections/Teaching Setup

. . . . . . . . . . . . .56

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Peference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

COMMERCIAL MODE

Page 6

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.

User must use shielded signal interface cables with ferrite cores to maintain standard compliance for the product.

Owner’s Manual CD Manual

Power Co rd

Shown herein is an optional Installer remote control available for the 26LH1DC3/4/5 models only. The installer remote control is NOT included with the TV.

•However, the user's remote is included with the TV.

To perform a normal installation set up, you need an installer's remote and the LT2002 Quickset II Clone Programmer – both are shown and described in later sections. See your LG dealer if you wish to purchase the Installer remote and LT2002. The installer remote allows access to the Installer menus, User menus in the Manual Channel Set options on the Setup menu. The installer remote has Menu, Select, and Adjust Keys. The LT2002 Quickset II Clone Programmer is used to duplicate a TV's setup and install it on another identical TV.

Optional Installer Remote Control for Model No. Series 26LH1DC3/4/5

Purchase the Optional Installer's Remote and Clone Programmer

User Remote Control. Batteries

Installer Remote Control. Batteries (Optional )

POWERMUTE

TV/AV

PREVIEW

GUIDE

SAP INFO

123

456

TIMER

FLASHBK

VOL

ALARM

Design and specifications are subject to change without prior notice.

NOTE

PREPARATION

Page 7

PREPARATION

FRONT PANEL INFORMATION

On-Screen Displays

See descriptions on page 25. On-screen displays will appear when the feature is active or the function is being used.

Use the VV OO LL (Volume) Up/Down button to

adjust the sound level to your preference.

Use the CC HH (Channel) Up/Down button to cycle through the available channels.

Displays the current channel bank. Press again to change banks.

Press MMEE NNUU repeatedly to scroll through menus.

TV Operation Press the PP OOWWEE RR button to turn the TV on from standby mode.

Power / Standby Indicator Glows red in Standby mode. Glows green when the TV is turned on. Glows orange in Sleep Timer and/or Alarm mode.

/ I

LED Color Action/Status

RED Power is Off (Standby)

GREEN is flashing Power On sequence is processing

GREEN Power is On

ORANGE If Power is Off On Timer is set or Alarm is set

If Power is On Off Timer is set or Sleep Timer is set

CDE

■

Here shown may be somewhat different from your TV.

■

Using the front control panel to operate the TV.

Front Panel Controls

Remote Control Sensor

With Installer menu item 11 buttons Defeat set to 000 (the default setting), Menu and TT VV//AA VV buttons are disabled.

NOTE

/ I

Page 8

PREPARATION

Back Connection Panel

M.P.I. INTERFACE

Use with clone programmer.

FUTURE USE

DVI/PC AUDIO IN

PC IN

HDMI/DVI IN

DIGITAL AUDIO OUT (Optical)

RS-232C PORT

RS-232C SELECT SWITCH

UPDATE SWITCH

ANTENNA CABLE

Connect to an antenna or cable system.

S-VIDEO IN

AUDIO / VIDEO 1, 3 IN

Connect Audio / Video equipment to these jacks.

COMPONENT 1, 2 IN

AC IN

RJP INTERFACE

VIDEO2(SIDE AUTO-CAMPORT)

VIDEO IN AUDIO IN

AUDIO/ VIDEO 2 (SIDE AUTOCAMPORT)

PREPARATION

BACK PANEL INFORMATION

■

Here shown may be somewhat different from your TV.

RS-232C, Update Switch and RS-232C Select Switch are reserved for qualified and authorized service and technical support personal only.

NOTE

Page 9

PREPARATION

VESA WALL MAUNTING

There are several Vesa standard mounts available that can be used with this TV. The mount shown to the right would be installed on the TV back using required bolts in the four pre-threaded holes provided. Fo llow any instructions supplied with the Vesa mount if one is to be used for the TV installation.

Swivel Stand

- The TV can be conveniently swiveled on its stand 30° to the left or right to provide optimum viewing angles.

■

Here shown may be somewhat different from your TV.

TV Swivel Stand

Vesa Standard Mounting Holes

Typical Ves a Mount

Page 10

EXTERNAL EQUIPMENT SETUP

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.

For optimum picture quality, adjust antenna direction if needed.

Wall Antenna Socket

Outdoor Antenna (VHF, UHF)

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire when connecting the antenna.

Copper Wire

2. Cable

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

Antenna

UHF

Signal Amplifier

VHF

3. Using both cable and antenna

Cable TV Wall Jack

Antenna

RF Coaxial Wire (75 ohm)

Diplexer

(Signal

Combiner)

The TV will let you know when the analog, cable, and digital channel scans are complete.

NOTE

Page 11

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

L R Y PB PR

When connecting Component cable

1. How to connect

Connect the audio output of the digital set-top box to

the CCOO MMPPOO NN EENN TT(( DDVV DD // DD TT VV ))11 jacks on the set.

Connect the video outputs (Y, PB, PR) of the digital set

top box to the CCOO MM PP OO NNEE NN TT ((DD VVDD // DD TT VV ))11 jacks on the set. Match the jack colors

(Y = green, PB = blue, and PR = red).

2. How to use

■

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box. operation)

■

Select CCoommppoonn eenntt 11 input source by using the TT VV//AA VV

button on the remote control.

■

If connected to CC OO MM PPOONN EE NN TT (( DDVVDD//DDTTVV ))22 input, select CCoommppoonn eenntt 22 input source.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

Signal

480i

480p

720p

1080i

Component 1/2

Yes

HDMI1/DVI,

HDMI2

Yes

Page 12

EXTERNAL EQUIPMENT SETUP

When connecting HDMI cable

No separated audio connection is necessary. HDMI supports both audio and video.

Connect the digital set-top box to HH DDMM II // DDVV II IINN jack on the set.

1. How to connect

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

■

Select HH DD MM II input source by using the TT VV //AA VV button

on the remote control.

When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player output resolution will be automatically set to 720p.

If the device does not support Auto HDMI, you need to set the output resolution appropriately.

NOTE

Page 13

EXTERNAL EQUIPMENT SETUP

Connect the audio output of the digital set-top box to the DD VVII// PPCC AAUUDDIIOO IINN jack on the set.

Connect the DVI output of the digital set-top box to the HHDDMM II// DDVV II IINN jack on the set.

1. How to connect

■

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

■

Select HH DD MM II input source by using the TT VV //AA VV button

on the remote control.

2. How to use

When connecting HDMI to DVI cableWhen connecting HDMI to DVI cable

Page 14

EXTERNAL EQUIPMENT SETUP

DVD SETUP

When connecting Component cable

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component Input ports

Component ports on the TV

YPB PR

Video output ports

on DVD player

B-Y

R-Y

Connect the audio outputs of the DVD to the CC OO MM PPOONN EE NNTT (( DDVVDD//DD TTVV )) 11 jacks on the set.

Connect the video outputs (Y, PB, PR) of the DVD to the CCOO MMPPOO NN EENN TT(( DDVV DD // DD TT VV ))11 jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red).

1. How to connect

2. How to use

■

Tu rn on the DVD player, insert a DVD.

■

Select CCoommppoonn eenntt 11 input source by using the TT VV//AA VV

button on the remote control.

■

If connected to CCOO MMPP OO NN EE NN TT ((DD VVDD // DD TT VV ))22 input, select CCoommppoonn eenntt 22 input source.

■

Refer to the DVD player's manual for operating instructions.

L R Y PB PR

Page 15

EXTERNAL EQUIPMENT SETUP

When connecting with an S-Video cable

When connecting HDMI cable

No separated audio connection is necessary. HDMI supports both audio and video.

Connect the HDMI output of the DVD to the HHDDMM II// DDVV II IINN jack on the set.

1. How to connect

2. How to use

■

Select HH DD MMII input source by using the TT VV // AA VV button on

the remote control.

■

Refer to the DVD player's manual for operating instructions.

If the device does not support Auto HDMI, you need to set the

output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 720p.

NOTE

Connect the audio outputs of the VCR to the AAUU DD IIOO input jacks on the set.

Connect the S-VIDEO output of the VCR to the

SS--VV IIDD EE OO input on the set.

1. How to connect

Page 16

EXTERNAL EQUIPMENT SETUP

VCR SETUP

When connecting with an antenna

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon.

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

Connect the antenna cable to the RF antenna in socket of the VCR.

Connect the RF antenna out socket of the VCR to the AA NN TT EE NN NN AA//CCAA BBLLEE socket on the set.

1. How to connect

■

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

2. How to use

Page 17

EXTERNAL EQUIPMENT SETUP

When connecting with a RCA cable

Connect the VVII DDEE OO11 jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

■

Select AA VV 11 input source by using the TTVV// AA VV button on

the remote control.

■

If connected to VVIIDD EEOO 33, select AA VV33 input source.

When connecting with an S-Video cable

Connect the audio outputs of the VCR to the AA UU DD IIOO II NN jacks on the set.

Connect the S-VIDEO output of the VCR to the SS--VV IIDD EE OO input on the set.

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

■

Select SS-- VV II DD EE OO input source by using the TT VV //AAVV but-

ton on the remote control.

1 2

The picture quality is improved: compared to normal composite (RCA cable) input.

NOTE

Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.

CAUTION

Page 18

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

Connect the VVII DDEE OO22 jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)

1. How to connect

2. How to use

■

Select AA VV 22 input source by using the TT VV //AA VV

button on the remote control.

■

Operate the corresponding external equipment.

■

Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.

Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.

Set the “Digital Output - Dolby Digital” in the Sound menu. (G p.44). See the external audio equipment instruction manual for operation.

Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.

1. How to connect

DIGITAL AUDIO OUTPUT

When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p.46)

NOTE

Do not look into the optical output port. Looking at the laser beam may damage your vision.

CAUTION

Camcorder

Video Game Set

ex) TV Model

Page 19

EXTERNAL EQUIPMENT SETUP

When connecting HDMI to DVI cable

Connect the PC audio output to the DD VVII// PPCC AA UUDDIIOO II NN jack on the set.

Connect the DVI output of the PC to the HH DDMM II //DD VVII II NN jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select HH DD MMII input source by using the TT VV // AA VV button on the remote control.

When connecting D-sub 15pin cable

Connect the PC audio output to the DD VVII// PPCC AA UUDDIIOO II NN jack on the set.

Connect the RGB output of the PC to the PP CC IINN jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select PPCC input source by using the TT VV//AA VV button on the

remote control.

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

PC SETUP

Page 20

EXTERNAL EQUIPMENT SETUP

To get the the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the

VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen.

The synchronization input form for Horizontal and Vertical frequencies is separate.

RGB-PC, HDMI1/DVI-PC mode

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.469 70.08

31.469 59.94

37. 879 60.31

48.363 60.00

47. 776 59.87

47. 720 59.799

47. 130 59.65

Resolution

720x400

13 6 0x768

640x350

* RGB-PC mode only: 640x350, 720X400

640x480

800x600

10 2 4x768

HDMI1/DVI-DTV,

HDMI2-DTV mode

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.469 59.94

31.500 60.00

44.960 59.94

45.000 60.00

33.720 59.94

33.750 60.00

Resolution

720x480

12 8 0x720

19 2 0x1080i

12 8 0x768

13 6 6x768

Supported Display Specifications

NOTE

Page 21

EXTERNAL EQUIPMENT SETUP

SCREEN SETUP FOR PC MODE

When the RGB input of the set is connected to a PC output, select the RGB-PC as the main input mode. When HDMI/DVI connect to PC output and select HDMI/DVI input, this function is used. After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality. When you change the resolution, select the proper resolution in pre-sent input to see the best picture appearance.

Overview

Position

Frequency 50 Phase 98 Auto

--:-- --

--. -- ----

F G Move OK Select Menu Back

Position

Frequency Phase Auto

--:-- --

--. -- ----

DEF G Move Menu Back

Time V-Chip

Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Adjustment for screen Position, Frequency, Phase and Auto

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight PP CC and press the OO KK (( EE nn ttee rr)) button.

Use the AA DDJJ D or E button to highlight PPoossii ttii oonn, FFrree qq uueennccyy,PPhh aa ss ee,AAuu tt oo and press the OO KK ((EE nn ttee rr)) button.

Use the AA DDJJ DEF G button to make appropriate adjustment. When finished, press OO KK (( EE nnttee rr)) button.

■

The FFrreeqquueennccyy, PP hh aa ss ee adjustment range is 00~1100 00.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 22

EXTERNAL EQUIPMENT SETUP

DVI HOOKUP TO RJP OR DVD PLAYER

Connect a DVI cable between the RJP and DVI in port on the TV.

Locate the DVI out port on the RJP (Remote Jack Pack) or DVI device.

1. How to connect

If required, make Audio connections as indicated to the right.

After all connections have been made, select the DVI source to display the DVI image on the TV.

COMPUTER PC HOOKUPCOMPUTER PC HOOKUP

Locate the computer out port on the computer.

1. How to connect

Make PC Audio connections as indicated to the right.

After all connections have been made, select the PC source to display the PC image on the TV.

Connect a computer cable between the computer and PC

In on the TV.

Computer Output

Back of

Computer

Audio Out

Page 23

WATCHING TV / CHANNEL CONTROL

USER REMOTE CONTROL BUTTON FUNCTIONS

POWERMUTE

TV/AV

PREVIEW

GUIDE

SAP INFO

123

456

TIMER

FLASHBK

VOL

ALARM

User

Remote Control

MUTE

Turns sound Off and On, while the picture remains.

CHANNEL PREVIEW

Displays available TV channels, and (if active) the Guest Parental Control menu: set V-Chip blocks to restrict both analog and digital programming.

• Aux Channel allows the guest to select the Audio / Video inputs. (Use the A/V jacks on the back of the TV as a source).

[-] BUTTON

When selecting a digital broadcast channel, key in the Main channel number followed by the -> [-] -> then the sub channel number. Analog channels do not contain a sub channel number.

INFO

Check the current program information, screen status, multi-sound status and time. Press with Guide onscreen for more Program information.

Press to activate English subtitles.

POWER

Turns TV On or Off.

FLASHBK (FLASHBACK)

Use to return to the last channel viewed.

NUMBER BUTTONS

Use for direct channel entry.

GUIDE

Use to view DTV program information. Press INFO for additional information.

ALARM

Use to go to the Alarm menu. Set a time for the TV to turn itself on.

TIMER

Press repeatedly to select a preset time to automatically shut the TV off.

VOLUME / CHANNEL / OK (Enter)

Increase or decrease the volume / Change channels. Select on-screen menu items and change menu values.

SAP

Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.

TV/AV

Displays a menu of all available input sources.

A brief list of the buttons on the optional user’s remote and what they do.

Page 24

WATCHING TV / CHANNEL CONTROL

INSTALLER REMOTE CONTROL BUTTON FUNCTIONS

A brief list of the buttons on the optional installer’s remote and what they do.

Installer

Remote Control

POWER

Turns TV On or Off.

TV/FM

Not application

VOLUME (-/+)

Decreases/increases sound level.

CC (Closed Captioning)

Press to access closed captions.

TIMER

Press repeatedly to select a preset time to automatically shut the TV off.

NUMBER KEYPAD

When selecting a digital broadcast channel, key in the Main channel number followed by the -> [-] -> then the sub channel number. Analog channels do not contain a sub channel number.

MENU/SELECT/ADJ (Adjust)

Press to display the main on-screen menu. Use SELECT to choose an option and ADJ (adjust) Left/Right to change the selected option.

FLASHBK (Flashback)

Returns to the previous channel viewed.

CHANNEL (-/+)

Tunes to next available channel.

MUTE

Turns sound Off and On, while the picture remains.

CHANNEL PREVIEW

Displays available TV channels, and (if active) the Guest Parental Control menu: set V-Chip blocks to restrict both analog and digital programming.

• Aux Channel allows the guest to select the Audio / Video inputs. (Use the A/V jacks on the back of the TV as a source).

ALARM

Use to go to the Alarm menu. Set a time for the TV to turn itself on.

ENTER (OK)

Press to view the Channel/Time display or to remove any on-screen display or menu.

Page 25

WATCHING TV / CHANNEL CONTROL

Use the remote keys indicated below to access these menus and displays. In this manual, the OSD (On Screen Displays shown) may be different. The following are just generic examples to familiarize you with the TVs options.

ON-SCREEN MENUS SELECTION

Volume Display

Press VOLUME. Shows currently selected sound setting.

Sleep Timer Menu

Press TIMER. Sets a time to automatically turn the TV off and shows remaining time before TV shutoff.

SAP Display

Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.

Caption Display

Press the CC. Turns selected option on or off. See Closed Captions page to select options.

Alarm Timer

Current Time 11:17 AM

Exit

AdjustMove

Hr.

Off

Min.

Alarm Display

Press the ALARM. Set a time for the TV to turn itself on.

Guide Display

Press the GUIDE to view DTV program information.

Channel Preview

Press the CH PREVIEW. Displays available TV channels.

V-Chip

Press the CC. Move to the V-Chip menu.

INFO

Press the INFO. Check the current program information.

SAP

Stereo

TIMER

Off

CAPTION

OFF

Page 26

WATCHING TV / CHANNEL CONTROL

WATCHING TV /CHANNEL CONTROL

Auto Program finds channels being received by the TV’s analog and digital tuners.

Cable will not work unless you subscribe to a cable service.

NOTE

CHANNEL SEARCH

With the optional Installer remote control in hand and press the PPOOWWEE RR button to turn the TV on.

Use Auto Program to automatically find and store all of the channels available in the selected Tuning Band.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the CC hhaa nnnnee ll menu and press the OOKK (( EEnn tt ee rr)) button.

Press the OO KK ((EE nnttee rr )) button to highlight AAuuttoo pprr ooggrraamm.

Press the OO KK (( EE nnttee rr)) button to start the channel search. After finding all available channels, a display appears briefly showing the number of analog and digital channels found.

Auto Program (Channel Search)

Tuning Band must be set before doing the channel search. See Installer menu item 003 Band/AFC. Default setting is 1, for CATV. When Auto Program is run, any assigned channel labels are automatically removed.

NOTE

Antenna

Auto Program G

Channel Label Channel List Fine Tune Auto Signal Strength

--:-- --

--. -- ----

Antenna

Auto Program

Channel Label Channel List

Fine Tune Signal Strength

--:-- --

--. -- ----

Antenna

Auto Program

Channel Label Channel List Fine Tune

Signal Strength

--:-- --

--. -- ----

Press OK to Search

Yes

Move OK Select Menu Back

F G Move OK Select Menu Back

Menu Back

Page 27

WATCHING TV / CHANNEL CONTROL

If you delete a found channel, it isn’t gone forever.

Simply re-enter the Channel List menu and re-add the channel

to show the check mark.

NOTE

After the channel search, remove unwanted channels.

Channel List

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the CC hhaa nnnnee ll menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight CChh aannnn eell LLii sstt and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight the channel you wish to delete and press the AA DD JJ G button. The AA DD JJ G button toggles the check mark on and off. If the check mark appears next to the channel number, the channel appears in the channel scan.

When finished, press MMEE NN UU repeatedly to remove the menus.

Antenna Auto Program Channel Label

Channel List

Fine Tune Signal Strength

--:-- --

--. -- ----

Antenna Auto Program Channel Label

Channel List

Fine Tune Auto Signal Strength

--:-- --

--. -- ----

Move OK Select Menu Back

DEMove G Add/Del OK View Menu Back

Page 28

WATCHING TV / CHANNEL CONTROL

WATCHING TV /CHANNEL CONTROL

Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the Channel Labels option highlighted, use the AA DDJJ

DD EE FF GG

buttons to scroll through the available channel labels, such as, A&E, AMC, ESPN, HBO, etc. These are a series of preset labels from which you can choose the more common networks. Use any of these to label the channels in the TV’s memory.

Channel Labels Setup

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the CC hhaa nnnnee ll menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight CC hhaa nnnnee ll LL aa bb ee ll and press the OOKK (( EE nnttee rr)) button. This action displays the CC hhaa nnnnee ll LL aa bb eell menu.

Use CChhaannnn eell D or E (+ / -) button to select channels and the AA DD JJ DEF Gbuttons to navigate the labels menu.

When the label is highlighted you want for the channel shown in the screen and press OO KK (( EE nn ttee rr)) button to add the label to the channel.

Select the next channel to label with CChhaannnn eell D or E (+ / -) button to or if finished channel labeling.

Antenna Auto Program

Channel Label

Channel List Fine Tune Auto

Signal Strength

--:-- --

--. -- ----

Move OK Select Menu Back

Move

Change Ch. Add/DeleteCH

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 29

WATCHING TV / CHANNEL CONTROL

If a dashed line or no color appears, the screen is unstable, therefore try channel adjustments. (This is only available for analog broadcasting.)

Unstable Screen

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the CC hhaa nnnnee ll menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight FF iinnee TTuu nn ee and press the OO KK ((EE nnttee rr)) button.

Press the AA DDJJ F or G button to adjust.

When finished, press MMEE NN UU repeatedly to remove the menus.

This shows the current digital signal strength as a picture. (This is only available for digital broadcasting.)

Checking the Strength of the Digital Signal

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the CC hhaa nnnnee ll menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight SSiigg nn aa ll SStt rree nn ggtthh and press the OO KK (( EE nnttee rr)) button.

View the on-screen signal strength monitor to see the quality of the signal being received.

When finished, press MMEE NN UU repeatedly to remove the menus.

Antenna Auto Program Channel Label Channel List

Fine Tune Auto

Signal Strength

--:-- --

--. -- ----

Move OK Select Menu Back

Antenna Auto Program Channel Label Channel List Fine Tune

Signal Strength G

--:-- --

--. -- ----

Move OK Select Menu Back

Antenna Auto Program

Channel Label Channel List

Fine Tune

Signal Strength

--:-- --

--. -- ----

F G Adjust Menu Back

Antenna Auto Program

Channel Label Channel List

Fine Tune

Signal Strength

--:-- --

--. -- ----

Menu Back

Page 30

TIME SETTING

CLOCK SETTING

Use the AA DDJJ DEF Gbuttons to set the year, month, day, hours and minutes.

Manual Time Settings

OOnn--OO ffff TT ii mmeerrss SS eettuu pp

Set the On-Off Timers using the procedures described above.

--:-- --

--. -- ----

Clock Manual G

Manual Clock Daylight Saving Time Zone On Timer Off Timer Auto Off Off

--:-- --

--. -- ----

Clock

Manual Clock

Daylight Saving Time Zone On Timer Off Timer Auto Off

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

--:-- --

--. -- ----

If you intend to use the On-Off Timers, it is best to set the clock manually.

NOTE

Move OK Select Menu Back

--:-- --

--. -- ----

Clock Manual

Manual Clock

Daylight Saving Time Zone On Timer Off Timer Auto Off Off

Move OK Select Menu Back

--:-- --

--. -- ----

Clock

Manual Clock Daylight Saving Time Zone On Timer Off Timer Auto Off

Auto Manual

DE Select Menu Back

DEAdjust F G Move Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk. Manual or Auto will appear on the menu next to clock. If manual is selected, on the menu use the AADD JJ D or E button to highlight MMaann uuaall and press the OO KK (( EE nn ttee rr)) button.

Use the AA DDJJ DEF Gbuttons to set the year, month, day, hours and minutes.

Use the AA DDJJ D or E button to highlight MMaannuuaa ll CC lloocckk and press the OO KK (( EE nnttee rr))button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 31

TIME SETTING

Mini glossary

If you select auto time setting, time will be set from the digital broadcast information.

Automatic Time Settings

Caution: Some digital channels may change the time incorrectly using the Automatic Clock Set feature.

In this event, the Alarm may not function as intended and the TV may not turn on at the expected time.

If the end user will have access to the Alarm, it may be best to use the Manual Clock Set mode and set the clock to local time manually.

NOTE

A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.

First two digits that are entered when setting the clock or the wake-up alarm.

TIME

HOURS

The last two digits that are entered when setting the clock, or the wake-up alarm.

MINUTES

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

--:-- --

--. -- ----

Move OK Select Menu Back

--:-- --

--. -- ----

Clock Manual G

Manual Clock Daylight Saving Time Zone On Timer Off Timer Auto Off Off

Move OK Select Menu Back

--:-- --

--. -- ----

Auto Off

Clock

Manual Clock Daylight Saving

Time Zone On Timer Off Timer

Auto Manual

DE Select Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk. Manual or Auto will appear on the menu next to clock. Select Auto on the sub-menu with the AA DD JJ D or E button and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ DEF Gbuttons to set the Daylight Savings and Time Zone options for your local area. See the next page.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 32

TIME SETTING

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

11:20 PM

Sep.11, 2006

Clock Manual Clock

Daylight Saving

Time Zone On Timer Off Timer Auto Off

No Yes

DE Select Menu Back

11:20 PM

Sep.11, 2006

Clock Manual Clock Daylight Saving

Time Zone

On Timer Off Timer Auto Off

Easten

F G Select Menu Back

Daylight Saving

Installer can select to use Daylight Savings to adjust the clock time. This is operated from the Automatic Time Settings.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk.

Use the AA DDJJ D or E button to highlight the DD aa yy llii gg hh tt SSaa vv ii nn gg and press the OO KK (( EEnn tt ee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Use the AA DDJJ D or E button to choose YYee ss or NN oo.

Installer can set the Time Zone. This is operated from the Automatic Time Settings.

Time Zone Settings

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk.

Use the AA DDJJ D or E button to highlight TT iimmee ZZoonnee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ F or G butt on to select the TT iimmee ZZ oo nnee and press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 33

TIME SETTING

11:20 PM

Sep.11, 2006

Clock Manual Clock Daylight Saving Time Zone On Timer

Off Timer

Auto Off

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

11:20 PM

Sep.11, 2006

Clock Manual Clock Daylight Saving Time Zone

On Timer

Off Timer Auto Off

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

DE Adjust F G Move Menu Back

TV Activation Time Settings

You can set a time for the TV to automatically turn-on.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk.

Use the AA DDJJ D or E button to highlight OO nn TT ii mmeerr and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ DEF Gbuttons to choose AA MM // PPMM, HHoouu rrss,MMii nnuu tt ee ss and time period to turn-on.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk.

Use the AA DDJJ D or E button to highlight OO ff ff TT iimmee rr and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ DEF Gbuttons to choose AA MM // PPMM, HHoouu rrss,MMii nnuu tt ee ss and time period to turn-off.

When finished, press MMEE NN UU repeatedly to remove the menus.

TV Deactivation Time Settings

You can set a time for the TV to automatically turn-off.

Page 34

TIME SETTING

Auto Off

If there is no signal on the TV for 15 minutes or more, or if no button is pressed for more than 3 hours, this function turns off the TV automatically.

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

11:20 PM

Sep.11, 2006

Clock Manual Clock Daylight Saving Time Zone On Timer Off Timer

Auto Off

Off On

DE Select Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E butt on to the TT ii mm ee.

Use the AA DDJJ D or E button to highlight AAuu ttoo OOffff and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to choose OO nn or OO ff ff.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the OO KK (( EE nnttee rr)) button to highlight CClloocckk.

Page 35

PARENTAL CONTROL/RATINGS

SET PASSWORD & LOCK SYSTEM

This option sets up or changes the password for blocking program ra tings.

Entering a PIN (Password)

If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.

NOTE

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV --CC hh iipp and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight OO nn/OO ff ff and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight OO nn and press the OO KK (( EE nn ttee rr)) button.

Use the AA DDJJ D or E button to highlight CC hhaa nn gg iinngg PPIINN and press the OO KK (( EE nnttee rr)) button.

Enter the digits password. As soon as the 4 digits are entered, re-enter the same 4 digits on the CC oonnff iirrmm PPIINN.

If a password has been entered, key it in using the number keypad. If no password has been set, enter the 4 digits password (0-9) using the remote control. This is the PIN. Each time the menu is entered, the password will be required until the block time expires. The TV is set up with the default password “0-0-0-0”.

When finished, press MMEE NN UU repeatedly to remove the menus.

Time

V-Chip

PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

On/Off

Changing PIN Set Block Hour TVPG Rating

D/L Rating

MPAARating Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Off On

On/Off

Changing PIN

Set Block Hour TVPG Rating MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

On/Off On

Changing PIN

Set Block Hour 12 TVPG Rating

D/L Rating

MPAARating Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

DE Select Menu Back

Move OK Select Menu Back

0 ~ 9 Number Menu Back

Page 36

PARENTAL CONTROL/RATINGS

Set Block Hour.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV --CC hh iipp and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight SS eett BBlloocc kk HHoouurr and press the OOKK (( EE nn tt ee rr)) button.

Use the AA DDJJ D or E button to choose 11~11 22 hours and

press the OO KK ((EE nnttee rr)) button.

Enter the 4 digits password.

When finished, press MMEE NN UU repeatedly to remove the menus.

Time

V-Chip

PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

On/Off On Changing PIN

Set Block Hour 12

TVPG Rating MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

On/Off Changing PIN

Set Block Hour

TVPG Rating MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

DE Select Menu Back

Page 37

MOVIE & TV RATINGS

You can block programs based on the TV program rating.

TVPG Ratings

Description of the TV (FCC) Rating Codes:

TV (FCC) Age Categories TV-MA

Mature audiences only. This program may contain mature themes, profane language, graphic violence and explicit sexual content.

TV-14

Parents strongly cautioned. This program may contain sophisticated themes, sexual content, strong language and more intense violence.

TV-PG

Parental guidance suggested. The program may contain infrequent coarse language, limited violence, some suggestive sexual dialog and situations.

TV-G

General audience. This contains little or no violence, no strong language, and little or no sexual dialog or situations.

TV-Y7

Directed for older children. Themes and elements in this program may include mild physical or comedic violence, or may frighten children under the age of seven.

TV-Y

All children. The themes and elements in this program are specifically designed for a very young audience, including children from ages two – six.

TV (FCC) Content Sub-Categories: V Violence. S Violence. L Offensive language. V Violence. D Dialog...sexual innuendo. FV Fantasy or cartoon violence.

Enter the 4 digits password.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV --CC hh iipp and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight the TT VVPP GG RR aa ttii nngg and press the OO KK (( EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Use the AA DDJJ DEF G buttons to choose and set up the menu options for TT VV PPGG RR aa ttii nngg.

PARENTAL CONTROL/RATINGS

Time

V-Chip

PC Menu Language Menu Transparency Set ID

11:20 PM

Sep.11, 2006

On/Off Changing PIN Set Block Hour

TVPG Rating

MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Time

V-Chip

PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

On/Off On Changing PIN Set Block Hour 12

TVPG Rating

MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

0 ~ 9 Number Menu Back

DE F G Move OK Select Menu Back

Page 38

PARENTAL CONTROL/RATINGS

Restricting movies by their rating.

MPAA Ratings

Description of the MPAA and TV (FCC) Rating Codes:

The MPAA Rating System (Movies) G General Audience. No restrictions. PG Children under 13 should be accompanied by an adult. PG-13 Parental guidance suggested. Children under 13 should

be accompanied by an adult.

NC-17 Not classified. Viewers should be 17 or older. X Adults only.

• MPAA ratings: The selected rating will be locked. In addition,

any ratings that are more restrictive will also be blocked.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV --CC hh iipp and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ DEFGbuttons to choose and set up the menu options for MM PPAA AA RRaa tt ii nngg.

When finished, press MMEE NN UU repeatedly to remove the menus.

Use the AA DDJJ D or E button to highlight the MM PP AA AA RR aa tt ii nngg and press the OO KK (( EE nnttee rr)) button.

Enter the 4 digits password.

Time

V-Chip

PC Menu Language Menu Transparency Set ID

11:20 PM

Sep.11, 2006

On/Off Changing PIN Set Block Hour TVPG Rating

MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Time

V-Chip

PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

On/Off On Changing PIN Set Block Hour 12 TVPG Rating

D/L Rating

MPAARating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

0 ~ 9 Number Menu Back

DE F G Move OK Select Menu Back

Page 39

PARENTAL CONTROL/RATINGS

Canadian English Ratings

Canadian English Ratings E Expect No restriction. C Children C8+ Viewers should be 8 or older. G General Audience. PG Parental guidance suggested. Children under 14 should be

accompanied by an adult.

14+ Restricted. Viewers should be 14 or older. 18+ Restricted. Viewers should be 18 or older.

Canadian French Ratings E Expect No restriction. G For a l l 8+ Restricted. Viewers should be 8 or older. 13+ Restricted. Viewers should be 13 or older. 16+ Restricted. Viewers should be 16 or older. 18+ Restricted. Viewers should be 18 or older.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV -- CC hhii pp and press the OO KK ((EE nnttee rr)) button.

Enter the 4digits password.

Use the AA DDJJ D or E button to highlight the CC aann .. EEnn gg ll iiss hh RRaa tt ii nn gg and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ DEF Gbuttons to choose and set up the menu options for CC aa nn .. EEnn gg ll iiss hh RRaa tt iinn gg.

When finished, press MMEE NN UU repeatedly to remove the menus.

Canadian French Ratings

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV -- CC hhii pp and press the OO KK ((EE nnttee rr)) button.

Enter the 4digits password.

Use the AA DDJJ D or E button to highlight the CC aann.. FF rr eenncchh RR aa tt iinn gg and press the OO KK ((EE nn ttee rr)) button.

Use the AA DDJJ DEF Gbuttons to choose and set up the menu options for CC aann .. FF rreenncchh RR aa tt iinngg.

When finished, press MMEE NN UU repeatedly to remove the menus.

Time

V-Chip

PC Menu Language Menu Transparency Set ID

11:20 PM

Sep.11, 2006

Time

V-Chip

PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

0 ~ 9 Number Menu Back

On/Off Changing PIN

Set Block Hour TVPG Rating MPAARating

D/L Rating

Can. English Rating

Can. French Rating

11:20 PM

Sep.11, 2006

On/Off Changing PIN Set Block Hour TVPG Rating

MPAARating

D/L Rating

Can. English Rating

Can. French Rating

11:20 PM

Sep.11, 2006

DE F G Move OK Select Menu Back

Page 40

PARENTAL CONTROL/RATINGS

Downloadable Rating

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight VV --CC hh iipp and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E buttons to choose DDiimm 00, DDii mm 11, DDii mm 22 or DDii mm 33 and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E buttons to choose DD11 LL 11, DD 11LL22 or DD 11LL33.

Use the AA DDJJ D or E button to highlight the

DD//LL RRaa ttiinn gg and press the OO KK (( EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Enter the 4 digits password.

■

LL oocckk mmeennuu--DDooww nnllooaa dd aa bbll ee RR aattiinngg in the CD manual is added by the information presented here. Your TV’s OSD (On Screen Display) may differ slightly from what is shown in this manual.

Time

V-Chip

Menu Language Menu Transparency Set ID

11:20 PM

Sep.11, 2006

On/Off On Changing PIN

Set Block Hour 12 TVPG Rating

MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

On/Off Changing PIN Set Block Hour TVPG Rating MPAARating

D/L Rating

Can. English Rating Can. French Rating

11:20 PM

Sep.11, 2006

0 ~ 9 Number MENU Back

DEMove OK Select MENU Back

Time

V-Chip

Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

DEMove OK Select MENU Back

D/L Rating (1/1)

Dim0

Dim1

Dim2 Dim3

This function may become available in the future and will be available only for digital channel signal.

This function operates only when TV has received Region5 Rating data.

NOTE

DEMove OK Select MENU Back

Page 41

SOUND & LANGUAGE CONTROL

CAPTION / TEXT

Turn Captions On/Off

Analog Mode

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

CAPTIONS

TEXT

Mini glossary

On/Off

Off

Analog Mode Digital Mode

Digital Font Option

11:20 PM

Sep.11, 2006

On/Off

Analog Mode CC1

Digital Mode Digital Font Option

11:20 PM

Sep.11, 2006

11:20 PM

Sep.11, 2006

On/Off

Analog Mode Digital Mode Digital Font Option

Off On

11:20 PM

Sep.11, 2006

On/Off

Analog Mode

Digital Mode Digital Font Option

CC1 CC2 CC3 CC4 TEXT1 TEXT2 TEXT3 TEXT4

Move OK Select Menu Back

DE Select Menu Back

DESelect Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the CC aappttiioonn menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight OO nn/OO ff ff and press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Use the AA DDJJ D or E button to choose OO nn or OO ff ff.

Pressing CC on the remote to select a captions option will also turn closed captions on.

NOTE

Analog Captions will display on the screen whether the signal is from an RF channel or external equipment input.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the CC aappttiioonn menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight AA nn aall oogg MMooddee and press OO KK ((EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to choose CCCC 11--TTEEXXTT44 and

press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Pressing CC on the remote selects a captions option.

NOTE

Page 42

SOUND & LANGUAGE CONTROL

Digital Captions Mode

Digital Font Options

If the digital options custom settings are to be cloned, all menu options should be set to any option other than Default. If Default is left set for any one option, then all the options will be reset to default after cloning.

NOTE

On/Off

Analog Mode

CC1

Digital Mode

Service1 G

Digital Font Option

11:20 PM

Sep.11, 2006

On/Off

Analog Mode

CC1

Digital Mode

Service1

Digital Font Option

11:20 PM

Sep.11, 2006

Font Size Default

Font Style Default Foreground Color

Default

Background Color

Default

Edge Color

Default

Foreground Opacity

Default

Background Opacity

Default

Edge Style

Default

11:20 PM

Sep.11, 2006

Caption

11:20 PM

Sep.11, 2006

On/Off Analog Mode

Digital Mode

Digital Font Option

Service1 Service2 Service3 Service4 Service5 Service6

Move OK Select Menu Back

DE Select Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the CC aa ppttiioonn menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight DD ii gg iittaa ll MM ooddee and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ D or E button to choose SSeerrvviiccee 11--SSeerrvviiccee 66 and

press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Pressing CC on the remote selects a captions option.

NOTE

Digital Captions only appear on digital channels, tune in a digi-tal channel that is actually broadcasting digital captions.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the CC aa ppttiioonn menu and press the OOKK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight DDiiggii ttaall FFoonntt OOpptt ii oonn ss and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ DEF Gbuttons to customize each option: Font Size, Font Style, Foreground Color etc.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 43

SOUND & LANGUAGE CONTROL

Preset Sound Settings

Match the sound mode to the program’s character, Music, Movie, Sports, or News. (This is Feature operates only in DTV mode.)

Mode Standard G

Balance Digital Output Dolby Digital

Auto Volume On Multi-Track Stereo Internal Speaker

11:20 PM

Sep.11, 2006

Mode

Balance Digital Output Auto Volume Multi-Track Internal Speaker

11:20 PM

Sep.11, 2006

Adjust the sound to suit your taste and room situations.

Sound Setting Adjustment-User Mode

Manual G

Treble

Bass

F G Move G Select Menu Back

Mode

Balance Digital Output Auto Volume Multi-Track Internal Speaker

11:20 PM

Sep.11, 2006

Standard G

Treble

Bass

F G Move G Select Menu Back

Move OK Select Menu Back

Mode Manual G

Balance Digital Output Dolby Digital Auto Volume On Multi-Track Stereo Internal Speaker

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMoo ddee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ G button to customize each option: or choose a preset mode like Music, Movie, etc.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMoo ddee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ G button to choose MMaann uu aa ll and use AA DD JJ DEF Gbuttons to set your own settings for the options. When finished, press the OO KK ((EE nn tt ee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 44

SOUND & LANGUAGE CONTROL

Adjust the speaker balance for optimum sound quality.

Sound Balance Setup

Mode

Balance

Digital Output Auto Volume Multi-Track Internal Speaker

11:20 PM

Sep.11, 2006

Adjust left/Light balance.

Set the digital audio output as Dolby Digital or PCM.

Digital Audio Output Settings

This product is under license of Dolby Laboratories. The “Dolby” or D symbol is a trademark of Dolby Laboratories.

Mode Balance

Digital Output

Auto Volume Multi-Track Internal Speaker

11:20 PM

Sep.11, 2006

Dolby Digital PCM

Mode Standard

Balance G

Digital Output Dolby Digital Auto Volume On Multi-Track Stereo Internal Speaker

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Standard Balance

Digital Output Dolby Digital G

Auto Volume On Multi-Track English Internal Speaker

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

F G Adjust Menu Back

DESelect Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight BBaa ll aa nncc ee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ F or G button to move the sound more to the Left or Right.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight DD iigg ii ttaall OOuu ttppuu tt and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJDor Ebuttons to choose DDooll bbyy DD ii gg iittaa ll or PPCC MM.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 45

SOUND & LANGUAGE CONTROL

Mode Balance

Digital Output Auto Volume

Multi-Track

Internal Speaker

11:20 PM

Sep.11, 2006

Have the TV automatically maintain the sound level between different channels.

Automatic Volume Control Settings

Mode Balance

Digital Output

Auto Volume

Multi-Track Internal Speaker

11:20 PM

Sep.11, 2006

Off On

Mono Stereo SAP

Mode Standard Balance

Digital Output Dolby Digital

Auto Volume On

Multi-Track Stereo Internal Speaker

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Standard Balance

Digital Output Dolby Digital Auto Volume On

Multi-Track Stereo

Internal Speaker

11:20 PM

Sep.11, 2006

DE Move OK Select Menu Back

DE Select Menu Back

You can set analog audio settings.

Analog Audio Settings

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight AA uu tt oo VVooll uumm ee and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ Dor Ebutton to choose OO nn or OO ff ff.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MM uull tt ii--TT rr aacckk and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJDor Ebutton to choose Mono, Stereo or SAP and press the OO KK (( EEnn tt ee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 46

SOUND & LANGUAGE CONTROL

Set the internal speaker to Off to listen to the TV through an external audio system, the TV sound will not be heard.

Using External Speakers

You can set digital audio language.

Digital Audio Language Settings

Mode Balance

Digital Output Auto Volume

Multi-Track

Internal Speaker

11:20 PM

Sep.11, 2006

English Spanish French

Mode Standard Balance

Digital Output Dolby Digital Auto Volume On

Multi-Track English

Internal Speaker

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Standard Balance

Digital Output Dolby Digital Auto Volume On Multi-Track English

Internal Speaker

On G

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

DESelect Menu Back

Mode Balance

Digital Output Auto Volume Multi-Track

Internal Speaker

11:20 PM

Sep.11, 2006

Off On

DE Select Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MM uull tt ii--TT rr aacckk and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJDor Ebutton to choose English, Spanish or French and press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SSoouunndd menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight IInnttee rr nn aall SS ppee aa kk eerr and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ D or E button to choose OO nn or OO ff ff and press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 47

SOUND & LANGUAGE CONTROL

Menu Language

The menus can be shown on the screen inter selected language. First select your language.

11:20 PM

Sep.11, 2006

Time V-Chip PC

Menu Language

Menu Transparency Set ID

English Español Français

Time V-Chip PC

Menu Language English

Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

DE Select Menu Back

Time

V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMee nn uu LLaanngg uuaa ggee and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ D or E button to highlight and set the Menu Language: English, Español or Français.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 48

SOUND & LANGUAGE CONTROL

Menu Transparency Settings

Menu Transparency sets the background transparency of the menu.

11:20 PM

Sep.11, 2006

Time V-Chip

PC Menu Language

Menu Transparency

Set ID

Opaque Semi Opaque Semi Trans Transparent

Set ID

Use this function to specify a set ID number.

11:20 PM

Sep.11, 2006

Time V-Chip

PC Menu Language Menu Transparency

Set ID

Time V-Chip PC Menu Language English

Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Time V-Chip PC Menu Language English Menu Transparency

Semi Opaque

Set ID 1

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

DE Select Menu Back

DE Adjust Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMee nnuu TT rraa nn ssppaa rree nn cc yy and press the OO KK (( EEnn tt ee rr)) button.

Use the AA DDJJ D or E button to highlight and set the Menu Transparency: Opaque, Semi Opaque, Semi Trans, Transparent.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the SS eettuu pp menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight SS ee tt IIDD and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to adjust SS ee tt IIDD to choose the desired monitor ID number.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 49

PICTURE CONTROL

PRESET PICTURE SETTINGS

Set the picture mode to the program content, e.g. Dynamic or Mild etc.

Picture - Preset

Choose one of three automatic color adjust ment.

Color Temperature Settings

Mode Standard G

Color Temperature

Cool

Screen Format

16:9 Noise Reduction Off Film Mode

Off

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Standard

Color Temperature

Cool

Screen Format

16:9 Noise Reduction

Off Film Mode Off

11:20 PM

Sep.11, 2006

Mode

Color Temperature

Screen Format Noise Reduction Film Mode

11:20 PM

Sep.11, 2006

Norma Cool Warm

Mode

Color Temperature

Standard

Contrast

Brightness

Sharpness

Color

Tint

Screen Format Noise Reduction Film Mode

11:20 PM

Sep.11, 2006

F G Move G Select Menu Back

Move OK Select Menu Back

DE Select Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMoo ddee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ G button to choose a preset picture setup. When finished, press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to choose

CCooll oorr TTeemm ppee rr aattuu rree and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to choose Normal, Cool or Warm. When finished, press the OOKK (( EE nn ttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 50

PICTURE CONTROL

The user can choose preset formats for the picture on analog channels.

Screen Format Adjustments

To make custom picture settings, set the Mode to Manual on the menu. Use the Manual settings for the best presentation of movies. The patient will then be able to view movies with more realism.

Manual Picture Adjustment

Mode Standard G

Color Temperature

Cool

Screen Format

16:9

Noise Reduction

Off

Film Mode Off

11:20 PM

Sep.11, 2006

Mode Standard Color Temperature

Cool

Screen Format

16:9

Noise Reduction

Off

Film Mode Off

11:20 PM

Sep.11, 2006

Mode

Color Temperature

Manual

Contrast Brightness Sharpness Color Tint

Screen Format Noise Reduction Film Mode

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Color Temperature

Screen Format

Noise Reduction Film Mode

11:20 PM

Sep.11, 2006

Set By Program 16:9 Zoom1 Zoom2 4:3

DE Select Menu Back

F G Move G Select Menu Back

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight MMoo ddee and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJ G button to choose MMaann uu aa ll and use AA DD JJ DEF Gbuttons to set your own settings for the options. When finished, press the MM EE NN UU button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DDJJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to highlight SS ccrree eenn FF oorrmm aatt and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJDor Ebuttons to choose a preset screen format: Set By Program, 16:9, Zoom1, Zoom2 or 4:3. When finished, press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 51

PICTURE CONTROL

The user can watch movies with a more realistic picture on analog channels. Turn Film Mode On to view movies with optimum preset picture settings.

Film Mode Options

Noise Reduction

The user can watch movies with a more realistic picture on analog channels.

Mode Standard Color Temperature

Cool Screen Format

16:9

Noise Reduction

Off

Film Mode Off

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Picture

Mode Standard Color Temperature

Cool Screen Format

16:9 Noise Reduction

Off

Film Mode Off G

11:20 PM

Sep.11, 2006

Move OK Select Menu Back

Mode Color Temperature Screen Format

Noise Reduction

Film Mode

11:20 PM

Sep.11, 2006

Off On

Mode Color Temperature Screen Format Noise Reduction

Film Mode

11:20 PM

Sep.11, 2006

Off On

DESelect Menu Back

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to choose NNooiiss ee RR eedduucc tt iioonn and press the OO KK (( EE nnttee rr)) button.

Use the AA DDJJDor Ebutton to choose OO nn or OO ff ff. When finished, press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Press the MMEE NN UU butt on and then use the AA DD JJ D or E button to highlight the PP iicctt uurree menu and press the OO KK (( EEnn tt eerr)) button.

Use the AA DDJJ D or E button to choose FFii llmm MMooddee and press the OO KK ((EE nnttee rr)) button.

Use the AA DDJJ D or E button to choose OO nn or OO ff ff. When finished, press the OO KK ((EE nnttee rr)) button.

When finished, press MMEE NN UU repeatedly to remove the menus.

Page 52

COMMERCIAL MODE

INSTALLER OVERVIEW

Operating Installer Menu

To set up the controls for the TV you will need to know how to enter the 26LH1DC3/4/5 Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the 26LH1DC3/4/5 Installer menu and how to make and save changes in the menu.

Optional Installer Remote

You will need an Installer remote control similar to the one shown to the right.

The TV’s clonable features need to be set up before 2-5-5 + Menu is done. This is a critical step. If the Master TV display panel’s clonable features like: Clock Set, adding channel icons and channel labels, etc. are not done properly, then the cloned 26LH1DC3/4/5 TVs will all have problems. For example, do not do 2-5-5 + Menu more than once or the TV setup will become corrupted. If you need to start the procedure over, then begin by setting installer item 117 to 001, and pressing Enter to reset the TV to default values in the installer menu. You can do 2-5-4 + Menu mode more than once but this mode is limited to only editing channel icons and channel labels.

Refer to the appropriate section in the Manual for other TV features: Picture, Sound etc.

*Note: Digital Font options are available only after a channel search has

been run and when the TV is tuned to an active digital channel with digital captions.

LT 2002 Clone Programmer

As the cloning procedure is being performed, specific steps need to

be done at the indicated times to achieve the desired result. Be sure to do each cloning task as indicated. If a procedure or step is left out or not performed correctly, then the TV setup will be wrong and cloning may not work. At each step, pay attention to assure the TV screen shows the proper message(s) when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog

channel,

not a digital channel.

Following is the Commercial Mode Operation Setup.

QuickSet II Programmer

LT2002

LODGING PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA 09F1 PTC V1.00.000 CPU V1.01.00

Typical Installer Menu

Page 53

COMMERCIAL MODE

COMMERCIAL MODE SETUP

*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program (Channel search) is disabled if there is an Aux input active. *Note2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu.

Overview: Commercial Mode Setup Procedure

1. Set Installer Menu Items

(Enter Installer Menu, see page 42 for detailed instructions.)

a. Set Installer menu item 117 F A CT DEFAULT, to 001 and press ENTER.

(This clears all installer menu items, custom settings, channel labels/icons and reloads the factory default settings.)

b. Set Item 003 BAND/AFC.

- Broadcast: set to 000.- HRC: set to 002

- CATV: set to 001.- IRC: set to 003

c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,

Channel Labels and Channel List options in the Channel Menu.

d. Set other particular installer items that affect your TV programming

network. See pages 57 - 62.

e. After all required installer menu item settings have been adjusted, press

ENTER on the remote to remove Installer Menu.

2. Set Up TV Features

(See Picture, Sound, Setup menus etc. See TV Clonable options list on page 62.)

*Note: Digital Font options are only available after a channel search has been run and when the TV is tuned to an active digital channel with digital captions.

3. Run Auto Program

(Search for all available channels.) Go to the Channel menu and access the Auto Program option, follow on-screen instructions.

a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.

• Delete channels per your system requirements: do you want to delete any free channels so the guest cannot access them?

•Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel onscreen display. Add identifiable labels for the end user to readily know what common networks are available. In the Channel menu, select the Channel Label option, follow instructions on the bottom of the screen.

4. Transfer TV Setup to Controller Box: 2-5-5 + Menu

After the TV channel scan has been edited and channel label icons added, enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU on the remote. This transfers the TV setup to the internal controller box.

*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted. TV scans available channels and exits menu when transfer to controller is complete.

5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode

Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to the channel on-screen displays. (See page 62.) To remove menu press MENU.

*Note: 2-5-4 + MENU can be performed more than once.

Verify TV Setup

At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements. Set item 028 CH OVERIDE to 000 to lock the channel scan. After the preceding has been completed, the Master TV setup is ready to be copied to the LT2002 Clone Programmer, see next page.

This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed instructions at each step; how to access and use the Installer menu etc.

L26W56XA Installer Menu

L26W56XA Installer Menu Items

RJP (Remote Jack Pack) TV Setup

Custom Channel Label ‘WXYZ’ created in 2-5-4 +

Menu Add Channel Label Mode

After TV setup has been verified,

set item 028 Ch Overide back to 000.

LODGING PTC INSTALLER MENU

117FACT DEFAULT 00X

003 BAND/AFC 00X

028 CH.OVERIDE 001

073 CH. NOT AVBLE 001

• RJP Available? If you will use an RJP in your system, review installer items:

-004 Start Channel cannot be set to

000.

-Set 040 Auto Camport to 000.

-Set 093 RJP Available to 001.

004 STRT CHANNEL XXX

040 AUTO CAMPORT 000

093 RJP AVAILABLE 001

028 CH. OVERIDE 000

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA 09F1 PTC V1.00.000 CPU V1.01.00

WXYZ

DIGIT AL 19-3

MONO SAPSTEREO

WXYZ

ANALOG 2

MONO

Page 54

COMMERCIAL MODE

CLONING CONNECTIONS/LEARNING SETUP

*Note1: It is assumed that the 26LH1DC3/4/5 is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, the clone programmer LED is blinking the required heart beat pattern, see above and next page.

*Note2: Once the clone is connected, do not touch the unit or otherwise disturb it or the MPI connections. Any disturbance while the clone is operating may disrupt the master setup transfer or copying etc.

- Connections for the LT2002 Clone Programmer to Learn the 26LH1DC3/4/5 Master TV Setup

Clone Programmer

Master 26LH1DC3/4/5

THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX

THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK = XX:XX TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

QuickSet II Programmer

LT2002

Ferrite Core (TDK, ZCAT 2035-0930)

Antenna or CATV

Warning: Do not use LT2002 if a Lodge Net PPV card is installed in TV or clone programmer device will be damaged.

Before you begin cloning...

• The Master 26LH1DC3/4/5 should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.)

•Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.) WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable.

• Use an Installer’s remote to operate Learning and Teaching menus.

• Make sure that the batteries in the Clone programmer are fresh.

• If batteries are removed, the Clone Clock time will be lost.

•Decide if you want to set the time from the Clone

programmer TV which has the clock set to the current time.

•Setting the time and transferring it to the Clone or other device is a separate procedure.

•Follow the connection diagram above to connect the Clone to a Master 26LH1DC3/4/5 TV display panel. After learning is complete, to another identical 26LH1DC3/4/5 TV display panel to “teach” it the master setup.

•After the 26LH1DC3/4/5s setup has been copied to another identical 26LH1DC3/4/5, that identical unit with the copied setup, needs to be disconnected from power for about 15 seconds to activate the newly-copied setup.

•See the Clone Tr oubleshooting section to resolve problems.

Turn to the next page to continue Cloning Setup.

Page 55

COMMERCIAL MODE

Learn Setup from Master 26LH1DC3/4/5

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master 26LH1DC3/4/5’s setup in by pressing either Channel button repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master 26LH1DC3/4/5’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master 26LH1DC3/4/5’s setup.

CLONE PROGRAMMER LEARNING SETUP

Instructions for the Clone Programmer to Learn the Master 26LH1DC3/4/5 Setup.

Learning the Master TV Setup

Use MPI Cable to Connect LT2002 Clone Programmer to Master 26LH1DC3/4/5 MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any button on the Installer remote .

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a LG TV equipped with M.P.I. input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

*Note: When using the clone programmer for teaching or learning, be sure that the heartbeat pattern is shown on the LEDs. Both learning and teaching should take about 45 or more seconds depending on the complexity of the master setup. While the clone is functioning, do not move it or otherwise disturb the clone or wiring connections. If the clone finishes the function in less than 45 seconds, redo the function again. Press the reset button if the clone does not act normally.

LT 2002 Clone Programmer Communication Problems

•A slow flashing green light indicates there are communication problems between the 26LH1DC3/4/5 and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

• If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK= XX:XX TV CLOCK= XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

This menu should appear by itself after the LT 2002 is connected to the 26LH1DC3/4/5 MPI port.

CLONE SELECTION MENU (1) LEARN FROM TV

(2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAYTV SETUP (6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

Page 56

COMMERCIAL MODE

CLONING CONNECTIONS/TEACHING SETUP

- Connections for the LT2002 to Teach another 26LH1DC3/4/5 the Master Setup

Teaching the Master Setup to Another 26LH1DC3/4/5

Teach Master 26LH1DC3/4/5’s Setup to the target 26LH1DC3/4/5

After learning is complete, remove the M.P.I. cable from the master 26LH1DC3/4/5 and connect it to the target 26LH1DC3/4/5 that you want to copy the master 26LH1DC3/4/5’s setup into. With “THE CLONE HAS CONTROL OF TV” message displayed, press 2 to go to the “TEACH TO TV” option, press ON/OFF, POWER, or ENTER. Select the LT2002 memory that the new setup is in. Press On/Off to transfer the new setup and other information to the new 26LH1DC3/4/5. Teaching usually takes 2-3 minutes. After the “TEACHING COMPLETE” message is displayed, press any button to return to the Clone menu, then press ON/OFF, POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly cloned 26LH1DC3/4/5.

Disconnect 26LH1DC3/4/5 Power for 15 Seconds

Unplug the AC power cord of the newly cloned 26LH1DC3/4/5 from the power outlet for about 15 seconds to activate the newlycopied setup.

Clone Programmer

Master 26LH1DC3/4/5

Ferrite Core (TDK, ZCAT 2035-0930)

Antenna or CATV

CLONE SELECTION MENU (1) LEARN FROM TV

(2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAYTV SETUP (6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

TEACHING IN PROGRESS,

PLEASE WAIT

TEACHING COMPLETE

This menu should appear after any key is pressed on the Installer remote.

This display will appear during Teaching function.

This display will appear after Teaching is complete.

Page 57

COMMERCIAL MODE

Accessing the Installer’s Menu

Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. Just press MENU repeatedly (at least 10 times) until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER to access the Installer’s menu. To remove the Installer’s menu, press ENTER again. Any changes you make will be stored in nonvolatile memory. (The menu also disappears automatically.)

The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow buttons to sequence through the available menu items. Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right arrow buttons. Or, enter a value directly.

Using the Installer’s Menu

Items 000 ~ 117 are immediately accessible only upon entering the

Installer’s Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages.

- Use the Installer’s Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages...

Installer Menu Items 000 through 117

Typical Installer Menu

LODGING PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA 09F1 PTC V1.00.000 CPU V1.01.00

Menu Item Function Value Range Default Value Brief Description of Function and Comments

000 INSTALLER SEQ 0 ~ 30 Leave default set to 0. 001 POWER MANAGE 0 ~ 70 Sets number of hours of no activity before auto shut Off.

002 AC ON 0 / 1 0 Set to 1 to enable auto turn On at power up. 003 BAND/AFC 0 ~ 31 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

004 STRT CHANNEL 0-125, 126, 127, 255 255 Channel at turn-on (Set 255 to return to last channel before power Off).

005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel. 007 STRT VOLUME 0 ~ 63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level). 008 MIN VOLUME 0 ~ 63 0Sets minimum allowable volume setting. 009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.

010MUTE DISABLE 0 / 1 0 Set to 1to disable mute function.

011 KEY DEFEAT 0 / 1 1 Set to 1 to disable menu navigation keys on display panel.

015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.

016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.

017 ALARM 0 / 1 1 Set to 1 to enable Alarm.

021V-CHIP 0 / 1 1 Set to 1 to enable V-Chip functions. 022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip (Parental Control) blocking hours.

023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting at power Off.

028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.

029 OLD OCV 0 / 1 0 Set to 1 to change M.P.I. operation to OCV.

030 ACK MASK 0 / 1 0 If set to 1, changes M.P.I. for some OCV boxes. 031 POLL RATE 20 ~ 16 994 Selects poll rate for M.P.I.

03 TIMING PULSE 186 ~ 227 207 Sets baud rate for M.P.I.

034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.

Page 58

COMMERCIAL MODE

INSTALLER MENU

- Installer Menu Items 035 through 117

Menu Item Function

Value Range

Default Value Brief Description of Function and Comments

035 COMPPORT EN. 0 / 1 1 Set to 1 to enable HDMI. Set to 0 to disable.

038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component 1 input jacks.

039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.

040AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport. 046 STRT AUX SRCE 1 ~ 7, 255255 Sets the starting AUX source.

047AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.

053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.

069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display. 070FOR. CH-TIME 0 ~ 72 Chooses custom foreground color for the Channel-Time display. 071 BCK. CH-TIME 0 ~ 72 Chooses custom background color for the Channel-Time display.

073 CH NOT AVBLE 0 / 1 0 If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed

when directly accessing a channel not in the favorite channel list.

075 REVERT CH 0 / 1 0 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel. 078 UPN MSB 0 ~ 2550 User programmable number, most significant byte. 079 UPN MSB-1 0 ~ 2550 User programmable number, most significant byte - 1. 080 UPN MSB-2 0 ~ 2550 User programmable number, most significant byte - 2. 081 UPN LSB 0 ~ 2550 User programmable number, least significant byte.

082 CHKSM ERROR 0 / 1 1 Enforces rigid M.P.I. checksum. 083 HANDSHK TIME 0 ~ 55Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.

084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.

087 REAR RGB EN. 0 / 1 1 Enables RGB1 input. Set to 1 to enable, set to 0 to disable.

088 EN NOISE MUTE 0 / 1 1 If set to 1, mutes audio if no signal is present.

090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.

091 YPrPb2 EN. 0 / 1 1 Set to 1 to enable Component 2 input jacks. 092RGB2 ENABLE 0 ~ 22

Enables Video 3 input. Set to 1 for Composite Video or 2 for S-Video. Set to 0 to disable.

093 RJP AVAILABLE 0 / 1 0 Set to 1 to enable.

094 SAP MENU EN 0 / 1 1

Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.

096 DEF. ASP. RATIO 0, 1, 2, 4, 5 2 Sets default aspect ratio at power up. See detailed descriptions and item 106. 10 2ATSC BAND 0 ~ 44 Selects ATSC band.

10 3ATSC TUNE MODE 0 / 1 1 Sets ATSC tuning mode. Set to 0 for virtual channels, set to 1 for physical channels. 10 4START MINOR CH 0 ~ 2550 Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.

10 6ASP RATIO LOCK 0 / 1 0

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.

107BANNER SELECT N/A N/A Not applicable.

116 VIDEO MUTE EN 0 / 1 0 Set to 0 for normal, set to 1 for Blank.

117FACT DEFAULT 0 / 1 0 0=Normal. 1=Loads factory default presets of all above settings.

Page 59

COMMERCIAL MODE

005 - CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if the system must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with START CHANNEL (Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the 26LH1DC3/4/5 will remain locked on Channel 3.

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the 26LH1DC3/4/5 is turned On. This feature is useful for an in-house information channel, since the 26LH1DC3/4/5 would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the 26LH1DC3/4/5 is turned Off; at turn On, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63 — change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every 26LH1DC3/4/5.

*Note: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others.

(Continued on next page)

*Note: For Items 007, 008 and 009

For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV.

To translate a TV volume level to the installer menu value, use the following formula: Installer Value = TV V

alue x 63 10 0

Enter only the whole number (disregard fractions).

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876 1 = 4321 2 = 1478 3 = 3698

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 - 7, with 1 - 7 representing the hours that the TV will remain On, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, allows the 26LH1DC3/4/5 to turn On just by applying AC power. Pressing the On button is not necessary. This is desirable if the 26LH1DC3/4/5 is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is Off, and 1 is On.

*Note: f set to 1 (On), the 26LH1DC3/4/5 does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

Selects the tuning band. There are 4 possible settings for this option:

0 = Broadcast 1 = CATV 2 = HRC 3 = IRC

If some channels were not found by Auto Program, select the appropriate Band setting here and add the channels using the Channel List option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial channel number when the 26LH1DC3/4/5 is turned On. This feature is useful for an in-house information channel, since the 26LH1DC3/4/5 would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the 26LH1DC3/4/5 was turned Off, to be the tuned to channel when the 26LH1DC3/4/5 is turned On again.

255 = Last channel 1-125 = Ch X 0 = Aux 12 6 = Map to Channel3. 127 = Map to Channel 4.

*Note: Item 004 STRT CHANNEL cannot be set to 0 if item 093 RJP AVAILABLE is set to “1”.

INSTALLER MENU

Page 60

COMMERCIAL MODE

029 - OLD OCV (On Command VideoTM)

Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. When set to 1, changes M.P.I. for some OCV boxes.

031 - POLL RATE

M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at default setting unless changed by Pay-Per- View provider. Step size of 16 ms.

032 - TIMING PULSE

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS.

034 - CAMPORT EN. (Camera Po rt Enable)

Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

035 - COMPPORT EN. (Computer Po rt Enable)

Enable/disables display panel HDMI input jack. Set to 0 to disable, set to 1 to enable.

*Note: The setting above is ignored if Installer item 093 RJP AVAIL ABLE, is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component Video 1 input. Set to 0 to disable display panel rear Component Video 1 input.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear AUX (Video 1) input. Set to 0 to disable display panel rear AUX (Video 1) input.

040 - AUTO CAMPORT

Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection.

*Note: This item must be set to 0 in order to enable item 093 RJP AVAILABLE to be set to 1.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting AUX source. Start source if start channel =0 1 = Video1 4 = RGB1 7 = Video 3 / S-Video 2 = Video2 5 = Component 2 255 = Last Aux 3 = HDMI 1 6 = Component 1

047 - AUX STATUS

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs.

(Continued on next page)

(Continued from previous page)

The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every 26LH1DC3/4/5.

*Note: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted, mute is disabled. If set to 0, sound can be muted.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, key defeat prevents the end user from accessing the onscreen menus with the display front panel—MENU, SELECT, and Left / Right arrow keys and TV/AV do not function. If set to 0, those keys do function.

*Note: The menus can always be accessed by pressing MENU on the Installer remote.

015 - SLEEP TIMER

If set to 1, the SLEEP TIMER feature may be used. If set to 0, the Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers)

If set to 1, Timer function is available to user. Set to 0 to disable On/Off Timer functions. (Clock must be set in order to use Timers.)

017 - ALARM

Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user. Set to 0 to disable the Alarm function.

*Note: Clock must be set before the Alarm function will work.

021 - V-CHIP (Parental Control)

Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to user; no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

023 - CAPTION LOCK

Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On. (Continued from previous page)

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel up/down or by direct keypad entry. If set to 0, only those channels that are added on the channel list can be selected.

Page 61

COMMERCIAL MODE

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red4 = Blue 7 = White 2 = Green 5 = Violet

*Note: If foreground and background colors are the same, menu background is transparent.

071 - BCK. CH-TIME (Channel-Time Display Background Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red4 = Blue 7 = White 2 = Green 5 = Violet

*Note: If foreground and background colors are the same, menu background is transparent.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel.

077 - QUICK SHUTOFF

Allows TV power off to be controlled by the pillow speaker channel selection button. User would press and hold button down for time required to have TV turn off. Value Range 0 - 17, each number represents 1/2 second. For example, if set to 4, TV would turn off if user held speaker channel button down for 2 seconds.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by M.P.I. command.

*Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by M.P.I. command. Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by M.P.I. command. Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by M.P.I. command. Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid M.P.I. checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on M.P.I. async port). SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time]).

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB1 Enable)

Controls access to rear RGB1 input on display panel. Set to 1 to enable RGB1 input for DTV. Set to 0 to disable RGB1 input.

*Note: The setting above is ignored if Installer item 093 RJP AVAILABLE, is set to 1. Then 087 - REAR RGB EN. above, always resets itself to PC (1) -- regardless of what value appears for item 087 on the Installer menu.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

090 - KEY LOCK

If set to 1, display panel keyboard is locked out, not available to end user. IR receiver remains functional.

091 - YPrPb2 EN. (Rear Component Video 2 Enable)

Set to 1 to enable display panel Component 2 input. Set to 0 to disable display panel Component 2 input.

092 - RGB2 ENABLE (Red-Green-Blue 2 Enable)

Set to 1 to enable display panel Video 3 input for Composite Video, set to 2 to enable for S-Video. Set to 0 to disable display panel Video 3 input.

093 - RJP AVAILABLE

Set to 1, remote jack pack is available. Set to 0, remote jack pack is not available.

*Note: This item can not be set to 1 if item 040 AUTO CAMPORT is set to 1.

(Continued on next page)

INSTALLER MENU

Page 62

COMMERCIAL MODE

(Continued from previous page)

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature, if available. Set to 0 to disable SAP feature.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up, see settings below.

10 2 - ATSC BAND

Sets up TV to receive different types of incoming signals: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.

10 3 - ATSC TUNE MODE

Selects ATSC tuning mode: 0=Virtual, 1=Physical. Note: The setting above is ignored if Installer item 102 ATSC BAND, is set to 1=CATV, 2=HRC, or 3=IRC. Then 10 3 - ATSC TUNE MODE above always resets itself to Physical (1), regardless of what value appears for item 10 3 on the Installer menu.

10 4 - START MINOR CHANNEL

Sets XX-XX minor starting channel at power up: 0=NTSC. If not 0, number selected is the Minor start channel number.

10 6 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power Off. Set to 0 to retain default aspect ratio with power Off. See item 96 Default Aspect Ratio above.

107 - BANNER SELECT

Not applicable.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for normal. Set to 1 for blank.

117 - FA CT DEFAULT (Factory Default)

Set to 0 for normal. Set to 1 to load default settings for all installer menu items.

WARNING: Setting this to 1 will reload the factory defaults and clear the channel list including erasing any assigned Channel Icons and Labels.

Set to 0 for set by program. Set to 1 for 4:3. Set to 2 for 16:9 (Factory Default). Set to 4 for Zoom 1 Set to 5 for Zoom 2

Page 63

COMMERCIAL MODE

Closable Menu Features

Channel

Auto Program (Active channels found with the channel search) Channel Labels Channel List Fine Tune

Picture

Mode Contrast Brightness Color Sharpness Tint Color Temperature Screen Format Film Mode

Sound

Mode Tr eble Bass Balance Auto Volume Multi-Track Internal Speaker

Setup

Time

Clock Auto Off

V-Chip

TVPG Rating

MPAA Rating Menu Language SET ID

Caption

On/Off Analog Mode Digital Mode Digital Font Option

*Note: For Digital Font Options, if any default setting is left unchanged prior to cloning, then all the digital font options wil be set to default settings. If you want custom digital font options to be clonable, set all digital font options to settings other than Default.

PEFERENCE

TV Features / Menus that can be Cloned

Page 64

COMMERCIAL MODE

Editing/Adding Channel ICONs and/or Labels

If there is no pre-assigned ICON, you can make a channel label of up to 7 characters to help in identifying the channel or network. At your option, channel labels can also be added in addition to a pre-assigned ICON. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

Editing and adding the labels can only be done if there are channels entered into the 26LH1DC3/4/5’s channel map either by using the method described in item 6 (page 64), by cloning or by the use of the master remote control from the PPV provider.

To Do Channel Editing/Labeling, proceed as follows

1. Enter 26LH1DC3/4/5 Installer menu.

2. After the installer menu appears, press ‘2’, ‘5’, ‘4’, ‘MENU’. This enters the channel label edit mode. Add your channel icons and channel labels in this menu, see below. (You can do this more than once.)

3. To exit the menu when done press “MENU”.

Adding Channel Icons and Labels in the 2-5-4 + Menu Mode

XYZ

NETWORK

(Label)

(Icon)

Changing a Channel’s ICON on Master TV

1. With Channel Up/Down, select the channel you want to change the Icon for.

2. With the Right or Left ADJ button, select the letter ‘I’ on the channel ID display.

3. With the Up or Down ADJ button, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter / Select.)

*Note: If no Icon is available, leave at or select the default blank icon display.

4. Proceed with Changing/Adding Labels orgo to the next channel.

Changing/Adding Channel Labels on Master TV

1. Channel Up/Down to select the desired channel.

2. Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character and so on.

3. With the Up or Down ADJ arrow, select the desired character.

4. Proceed to the next number position or use Channel Up/Down to go to the next channel.

Changing Source Labels on Master TV

1. Press “TV/AV” to select the desired Aux input source; Video 1, Component, S-Video etc.

2. Press the Right or Left ADJ arrow repeat-edly until the numbers 0 to 9 show up. The number shows the position of the character that can be changed.

3. Use the Up or Down ADJ arrow to select the desired character.

4. Press “TV/AV” for the next Aux source or proceed with Changing Icon or Changing/Adding Labels.

• CHANNEL Up/Down - Tunes in the next channel in

scan.

• Left/Right Arrows - Select the item to change. If “I”

is shown, the ICON can be changed. If a number is shown, it indicates the position of the character that can be changed.

•Up/Down Arrows - Select the ICON or the character

to be displayed.

•0 – 9 - Use to enter the index number of the ICON,

if known.

• OK (Enter/Select) - Changes the ICON after the

number has been entered.

• TV/AV - Changes the Aux input source for labeling.

This key is located on the side of the TV front and on Installer remote control.

•MENU - Exits the labeling/editing menu.

Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu

PEFERENCE

Procedures for adding Channel Label Icons/Custom Channel Labels (2-5-4 + MENU Mode)

Page 65

COMMERCIAL MODE

To set up a master TV you will need to know how to enter the 26LH1DC3/4/5 Installer menu and make changes to the default values

as required. If necessary, familiarize yourself with the 26LH1DC3/4/5 Installer menu and how to make and save changes in the menu, befor

e attempting

to clone the 26LH1DC3/4/5 Master TV setup.

You will also need an Installer remote control similar to the one shown in the front of this manual.

Finally, the TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel

labels are not correctly added, then the cloned 26LH1DC3/4/5s TVs will all have problems.

As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel.

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

Making a Master TV

Detailed Instructions

The following describes the procedure for preparing a Master 26LH1DC3/4/5 for cloning and the procedure for adding Channel Icons and/or Labels. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Program Scan is disabled if there is an Aux input active. Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu.

1. Enter the 26LH1DC3/4/5 installer menu.

a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been restored to factory default condition.

b. Within the Installer menu, set the Installer menu

items to the configuration required of your institution.

c. It is important to set the tuning band at this time,

see Installer menu item 03 BAND/AFC.

d. Set Installer menu item 28 – CH OVERIDE to 001

to allow access to the Auto Program and Channel List/Channel Label features in the Channel Menu. Exit the Installer menu.

2. Access the Master TV menus and set the clonable

options on the menus to the desired configuration. Refer to the Clonable Menu Features Chart on the see page 63.

3. Run Auto Program.

4. Enter the Channel List/Channel Label menu and edit

the channel line-up to include the Free-To-Guest

Channels only.

5. Assign ICONs to the channels using the Channel Label Menu. Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for channels without Icons.

6. Transfer the TV setup: Enter the 26LH1DC3/4/5 installer menu. Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the 26LH1DC3/4/5. Once the transfer is complete, the system will exit the Installer menu. Note: Only do 2-5-5 + MENU once. The TV setup may be corrupted if 255 + Menu is done more than one time.

7. Edit/Add Channel ICONs and Channel Labels as needed. Enter Installer menu. With menu displayed, press 25-4 + MENU. See page 62 for detailed instructions:

Editing/Adding Channel ICON and Labels on Master TV

Changing a Channel’s ICON on Master TV

Changing/Adding Channel Labels on Master TV

Changing Source Labels on Master TV

8. Verify Master TV setup and feature configuration:

• Did you add Channel ICONS?

• Did you add Channel Labels?

• Did you add Aux Source Labels?

• Did you adjust all TV menu options as required? The TV master setup is now ready to be cloned. Go to the master TV cloning section or continue on to page 52.

After verifying master setup, enter the 26LH1DC3/4/5 Installer menu and set Installer menu item 028 Ch Overide to 000.

PEFERENCE

Detailed Information For Making A Master TV

Page 66

COMMERCIAL MODE

The software version of the 26LH1DC3/4/5 may be checked by accessing the INSTALLER MENU. To do this, press the MENU button at least 10 times until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "OK (Enter/Select)".

Procedure to Check Software Version

Typical Installer Menu

LODGING PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA 09F1 PTC V1.00.000 CPU V1.01.00

PEFERENCE

Software Version Check

Page 67

COMMERCIAL MODE

The CAMPORT Auto Sense function is enabled when:

1. Installer Menu Item 34, CAMPORT EN is set to 1 AND

2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).

Selectable= Can be accessed with TV/AV key, direct access, etc. Auto Sense= Switches to this input when connector is inserted. The camport (Front Video) has the highest priority and will override any commands including tuning to the Start Channel.

Item 34

CAMPORT EN

0 0 1 1

Item 40

AUTO CAMPORT

0 1 0 1

Front Video

Operation

Disabled Disabled

Selectable

Auto Sense

CAMPORT (Front Video) Functionality Control

CAMPORT Operation (Stand-Alone)

When Camport Auto Sense is enabled as above, the TV’s source will switch to the front video whenever a plug is inserted into any of the front panel video inputs (either composite Video or S-Video).

When the plug is removed, the TV will switch back to the Previous channel or input source that the TV was using before the Plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source Keys (TV/AV) are ignored. Channel Up/Channel Down and Flashback Commands are not direct access tuning commands and they are also ignored.

CAMPORT Operation (PPV)

The operation will be similar to that of the Stand-Alone mode. However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command.

Previous State

Before Inserting

CAMPORT

Aux or RF Channel

Operation State

While CAMPORT

Is Active

None

Direct Access

Ch Up/Down,

Flashback

and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux

or RF Channel

Last Requested

RF or Aux Channel

Previous Aux

or RF Channel

Previous State

Before Inserting

CAMPORT

Aux or RF Channel

Operation

While CAMPORT

Is Active

None

Direct Access

Ch Up/Down,

Flashback

and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux

or RF Channel

Last Requested

RF or Aux Channel

Last Requested

Channel if PPV

translates it to direct

access tuning

command. Otherwise,

goes to Previous Aux

or RF Channel

PEFERENCE

26LH1DC3/4/5 Camport Auto Sense Operation

Page 68

COMMERCIAL MODE

26LH1DC3/4/5 Aux Input Configuration

DIRECT

ACCESS

Tuning

OLD_OCV

130 90

Video2 (Front)

CV ONLY

CAMPORT_EN

0x01 0

Video Front

(Camport)

0(VIDEO) 2

Video Front

(Camport)

131 91

Video1(Rear)

CV ONLY

DTV/PC

Auto

REAR_AUX_EN

0x02 1

Rear Video

(Aux)

0(VIDEO) 1

Rear Video

(Aux)

132 92

Component 2

YPrPb2 EN

0x04 2

S-Video

Rear

0(VIDEO) 5

S-Video

Rear

133 93

DVI/HDMI1

COMPORT EN

0x08 3

Front

Computer

0(VIDEO) 3

Front

Computer

DTV/PC

Auto

134 94

RGB1

REAR RGB EN

0x10 4

Computer 0(VIDEO) 4SVGA Rear

S-Video

135 95

Video 3

RGB2 ENABLE

0x20 5

NTSC Rear

Computer

0(VIDEO)

1(S-VIDEO)

NTSC Rear

Computer

136 96

Component1

YPrPb EN

0x40 6

Rear

YPrPb

component

video

0(VIDEO)

YUV

Component

OLD_OCV

Source Input Source Mode

Number

Value Value

Labeling LabelingLabeling

26LH1DC3/4/5

ENABLE

Installer Menu

MPI DATA

STATUS TYPE 0x41 SOURCES ENABLED (R/W)

DATA STATUS

TYPE 0xD2

CURRENT AV

SOURCE (R)

DATA

STATUS

TYPE 0X0D

AUX

SOURCE

(R)

MPI DATA

STATUS

AUX

SOURCE

ASSIGNMENT

PEFERENCE

26LH1DC3/4/5 Aux Input Configuration

Page 69

APPENDIX

TROUBLESHOOTING

Some quick and easy tips to resolving problems

Display Panel Picture

8 See troubleshooting flow chart.

No Power.

Power

Display panel is turned off.

Wrong tuning band.

Antenna/Cable not

connected.

Connections incorrect.

M.P.I. not connected.

Encrypted program.

8 Turn TV on.

8 Power failure?

8 Adjust Installer menu settings.

8 Connect Antenna/Cable signal source to 26LH1DC3/4/5.

8 Check connections on 26LH1DC3/4/5.

8 If applicable, connect M.P.I. cable to M.P.I. device.

8 Tr y a n o t h er channel.

No picture

Software Problems

8 Remove power cord for 5 minuts.

Software lockup.

TV not functions properly.

8 Start all over with item 117, set to 001, press Enter then redo Auto Program, Channel List, Clock, etc.

*Note: 2-5-4 + MENU can be done more than once.

2-5-5 + MENU performed

more than once.

Software Corrupted.

8 After 2-5-5 + MENU, only channels included in TV controller will appear.

If channel is available, redo channel scan. If it is not available it will not appear on the TV screen.

Channel not included

in channel scan in TV

controller.

Can not direct enter channel number

8 After Auto Program and Channel List, etc. press 2-5-5 + MENU to transfer channels and TV setup to

internal TV controller. Afterward, only Physical or only Virtual channels will appear in digital channel scan,

analog channel scan will be normal.

*Note: Be sure to set item 028 Ch Overide to 000.

2-5-5 + MENU not per-

formed.

Virtual and Physical channels appear in channel scan w/Channel Up/Down.

Page 70

APPENDIX

Remote Control

Picture Reception

Broadcast Tuning Mode Digital Channel OSD

*Note: For other problems not caused by the 26LH1DC3/4/5, refer to other devices’ operating guide.

Remote not in TV mode.

Not aimed at IR remote

sensor.

8 Use Mode key to select TV; puts remote into 26LH1DC3/4/5 mode.

Weak batteries.

8 Replace batteries.

Wrong battery polarity.

8 Check that “+” and “-” match in battery compartment.

Too much light in room.

8 Dim room light.

Incorrect Bed 1-2 setting.

8 Set correct Bed 1-2 setting.

8 Point remote at TV’s IR receiver on TV.

Remote too far from IR

sensor.

Remote too far from IR

sensor.

8 Move remote closer to TV’s IR receiver or darken room.

IR path to TV’s receiver

obstructed.

8 Remove obstructions.

Wrong Installer remote

control.

8 Requires compatible Installer remote, contact your LG dealer.

Remote doesn’t work.

8 Press MUTE or use Volume Up key to increase sound level.

Audio muted.

8 Tr y a different channel.

Broadcast problem.

8 Turn TV speakers on.

TV Speakers Off.

Normal picture, poor or no sound.

8 Set Item 103 to 0 for information to be added to virtual channel tuning digital OSD.

Item 103 set to 1 physical

channels tuning.

No Information available display.

Erratic Operation

8 Adjust Installer menu settings as required.

8 Remove TV power cord for 15 seconds.

Wrong Installer menu

settings.

Software problem.

Installer menu setup.

Page 71

APPENDIX

CLONING PROCEDURE TROUBLESHOOTING

Warning: Do not use LT2002 while a LodgeNet PPV card is installed in TV or clone programmer will be damaged.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

*Note: The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.)

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

8 Only use an appropriate Installer remote to operate clone programmer with 26LH1DC3/4/5.

Wrong Installer remote.

Remote does not operate clone.

8 Connect 26LH1DC3/4/5 to a reliable Analog channel signal source.

Weak signal.

Clone menu hard to read.

8 Set time on a TV, copy time to Clone Programmer.

Time not available.

No time set.

8 Connect M.P.I. cord.

M.P.I. cord not connected.

8 26 LH1DC3/4/5 must be powered On for clone to work.

26LH1DC3/4/5 not

turned on.

8 Install 4 fresh AA high-quality alkaline batteries.

Weak batteries.

LED does not blink

Page 72

APPENDIX

CLONING PROCEDURE TROUBLESHOOTING

• After cloning operations are complete, just unplug the LT2002 from the 26LH1DC3/4/5.

• If the 26LH1DC3/4/5 does not display a picture on the TV (blank screen) after a few seconds, just change channels.

Master and Other 26LH1DC3/4/5

8 Wait until procedure complete message is displayed.

Procedure interrupted.

8 Cloning is only possible with identical model TVs.

Different TV models.

8 Reread 54 - 55 - 56 pages to be sure all tasks were performed.

Step(s) omitted or not

performed.

8 Redo cloning and be sure learning/teaching time is about 1 min. and 5 to15 seconds (75 seconds).

Insufficient cloning time.

8 Reset Clone Programmer.

Cloning erratic.

Cloning did not work.

8 Batteries must remain installed to retain time settings.

Batteries were removed.

Clone time disappeared.

8 Disconnect newly cloned unit from power for 5 seconds.

26LH1DC3/4/5 not reset.

New Setup not present

8 Tr y a different LT2002 Clone programmer.

8 Reset Clone Programmer.

Clone programmer problem.

Clone not working

8 Retry cloning again.

Clone should only scan

channels once.

Clone Scans Channels more than once.

Page 73

APPENDIX

CLONE TROUBLESHOOTING FLOW CHART

Page 74

APPENDIX

TV OPERATING CHECK

Page 75

GLOSSARY OF TERMS

75 OHM RF CABLE

The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the Antenna/Cable threaded jack on the back of the 26LH1DC3/4/5.

300 TO 75 OHM ADAPTER

A small device that connects a two-wire 300ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.

ANALOG TELEVISION

Standard television broadcasting format in 4:3 picture aspect ratio.

A/V CABLES

Audio/Video cables. Three cables bunched together—right audio (red), left audio (white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE

Any device that produces video or sound (VCR, DVD, cable box, or television).

AMPLIFIER

An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other Audio/Video device.

ANTENNA

The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

CABLE

Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals. DVD, cable box, or television).

CATV

Programming provided by a cable service.

DIGITAL TELEVISION

High-resolution, cinema-quality television signals transmitted digitally.

DVI

Digital Video Interface Accommodates analog and digital interfaces with a single connector.

COMPOSITE VIDEO

Typical video jack, uses one wire for transporting three-color video signals.

COMPONENT VIDEO

Uses three wires for transporting three-color video signals. The end result is usually better video quality.

DELETED

Lets you remove channels from the list that the end user can scroll through using CH (Channel) Up/Down.

HDMI

High-definition multimedia interface.

HDTV

High-definition television. Refers to television signals that have higher resolution than ordinary analog TV signals.

HDSTB

High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher resolution than ordinary analog TV signals.

INPUT

Refers to the input jack that receives a signal from a TV, VCR, DVD Player or other Audio/Video device.

JACK

An input or output connector on the back of a TV, VCR, DVD Player or other Audio/Video device.

MONO SOUND

Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

OUTPUT

Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device.

PHYSICAL CHANNEL NUMBER

Actual digital major, dashed minor channel number that a station is broadcasting on.

RGB (Red, Green, Blue)

Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French.

SIGNAL

Picture and sound traveling through a cable, or over the air, to the TV.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio that’s divided into right and left sides.

TUNER

Device that picks up the broadcast signal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

The arbitrarily assigned digital dashed minor channel number that a station is broadcasting on.

A list of definitions for some of the words found in this guide

APPENDIX

Page 76

APPENDIX

INSTALLER QUICK SETUP GUIDE

Quick Setup Guide for Integrated Master TVs

See table of contents for more information.

Setup Instructions for Making a Master TV

1. Connect TV to signal source, connect power cord and turn TV power on.

2. Enter the TV installer menu.

*Note: If this is not a new setup, set Installer item 117 to 001 and press Enter to reset TV to default condition.

• Set Tuning Band. Set Installer menu item 003 BAND/AFC to CATV: 001, Broadcast: 000 etc.

• If necessary, set Installer menu item 028 CH OVERIDE to 001. In addition, set any other installer items as required of your system. Exit Installer menu.

3. Access the Master TV menus and set the closable options on the menus to

the desired configurations. Refer to the Closable Menu Features Chart for the TV. (Picture, Sound, Time etc.)

4. Do a Channel Search; run Auto Program. (aka EZ Scan.)

5. Enter the Channel Edit menu and delete channels per your requirements.

6. Enter the Channel Label menu and assign ICONs to the channels.

*Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 8, add Channel ICONS or custom text labels for channels which no Icons are available for.

7. Tr ansfer the TV setup. After all menu options and features are set to your

requirements, enter the installer menu. Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the PTC. After the transfer is complete, the system will exit the Installer menu.

8. Set any Channel Labels as needed. a. Enter Installer menu. b. Press ‘2’, ‘5’, ‘4’, ‘MENU’ to enter the menu. In this menu edit the assigned channel Icons, assign custom text labels for channels and assign labels for active Aux sources. Press ‘Menu’ to exit.

9. Enter the Installer menu. Set item 028 Ch Overide to 000 and exit menu.

LODGING PTC INSTALLER MENU

117FACT DEFAULT 00X

003 BAND/AFC 00X

028 CH.OVERIDE 001

028 CH.OVERIDE 000

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA 09F1 PTC V1.00.000 CPU V1.01.00

WXYZ

DIGIT AL 19-3

MONO SAPSTEREO

WXYZ

ANALOG 2

MONO

Antenna Wall Jack

AC Power Cord

RF Coaxial Wire

(75ohm)

Mode Standard G

Color Temperature

Cool

Noise Reduction Off

Screen Format

16:9

Film Mode

Off

11:20 PM

Sep.11, 2006

Antenna

Auto Program

Channel Label Channel List Fine Tune Auto Signal Strength

--:-- --

--.-- ----

Antenna

Auto Program

Channel Label Channel List Fine Tune Signal Strength

--:-- --

--.-- ----

11:20 PM

Sep.11, 2006

Mode

Color Temperature

Standard

Contrast 100 Brightness 79 Sharpness 65 Color 70 Tint 0

Screen Format Noise Reduction Film Mode

Move OK Select Menu Back

Menu Back

Page 77

NOTE

Page 78

NOTE

Page 79

PRODUCT SPECIFICATIONS

26LH1DC3/4/5

MODELS

27.01 x 22.0 x 9.97 inches / 686.0 x 558.7 x 253.2 mm

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 10 4°F (0 ~ 40°C)

Less than 80%

-4 ~ 14 0°F (-20 ~ 60°C)

Less than 85%

Dimensions

(Width x Height x Depth)

Weight

Power requirement

Television System

Program Coverage

External Antenna Impedance

Environment condition

33.95 pounds / 15.4 kg

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

The specifications shown above may be changed without prior notice for quality improvement.

Page 80

LG 26LH1DC3, 26LH1DC4, 26LH1DC5 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

WARNING / CAUTION

SAFETY INSTRUCTIONS

CONTENTS

PREPARATION

ACCESSORIES

FRONT PANEL INFORMATION

BACK PANEL INFORMATION

VESA WALL MAUNTING

EXTERNAL EQUIPMENT SETUP

ANTENNA OR CABLE CONNECTION

HD RECEIVER SETUP

DVD SETUP

VCR SETUP

OTHER A/V SOURCE SETUP

DIGITAL AUDIO OUTPUT

PC SETUP

SCREEN SETUP FOR PC MODE

DVI HOOKUP TO RJP OR DVD PLAYER

COMPUTER PC HOOKUPCOMPUTER PC HOOKUP

WATCHING TV / CHANNEL CONTROL

USER REMOTE CONTROL BUTTON FUNCTIONS

INSTALLER REMOTE CONTROL BUTTON FUNCTIONS

ON-SCREEN MENUS SELECTION

CHANNEL SEARCH

Auto Program (Channel Search)

Channel List

Channel Labels Setup

Unstable Screen

Checking the Strength of the Digital Signal

TIME SETTING

CLOCK SETTING

Manual Time Settings

Automatic Time Settings

Daylight Saving

Time Zone Settings

TV Activation Time Settings

TV Deactivation Time Settings

Auto Off

PARENTAL CONTROL/RATINGS

SET PASSWORD & LOCK SYSTEM

Entering a PIN (Password)

Set Block Hour.

MOVIE & TV RATINGS

TVPG Ratings

MPAA Ratings

Canadian English Ratings

Canadian French Ratings

Downloadable Rating

SOUND & LANGUAGE CONTROL

CAPTION / TEXT

Turn Captions On/Off

Analog Mode

Digital Captions Mode

Digital Font Options

Preset Sound Settings

Sound Setting Adjustment-User Mode

Sound Balance Setup

Digital Audio Output Settings

Automatic Volume Control Settings

Analog Audio Settings

Using External Speakers

Digital Audio Language Settings

Menu Language

Menu Transparency Settings

Set ID

PICTURE CONTROL

PRESET PICTURE SETTINGS

Picture - Preset

Color Temperature Settings

Screen Format Adjustments

Manual Picture Adjustment

Film Mode Options

Noise Reduction

COMMERCIAL MODE

INSTALLER OVERVIEW

COMMERCIAL MODE SETUP