LG 26LC7DC, 32LC4D, 42LC4D User Manual

Please read this manual carefully before operating your set.
Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
LCD TV MODELS
26LC7D 26LC7DC 32LC4D 42LC4D
www.lgusa.com / www.lg.ca / www.lgcommercial.com
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).
1

WARNING / CAUTION

WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
2
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus.
This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus when unused for long periods of time.
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner ManualOwner Manual
1
2
3
4
5
6
7
8
Owner Manual
3
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Never touch this apparatus or antenna during a thunder or lighting storm.
Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.
CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates dam­age or deterioration, unplug it, discontinue use
of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Outdoor use marking : WARNING - To reduce the risk of fire or elec-
tric shock, do not expose this appliance to rain or moisture.
Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus.
GGRROOUU NNDDIINNGG
Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DDIISS CCOONNNNEE CCTTIINNGG DDEEVVIICC EE FFRROOMM MMAAII NN SS
Mains plug is the disconnecting device. The plug must remain readily operable.
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
9
12
10
11
13
14
15
16
17
Power Supply
Short-circuit
Breaker
4

CONTENTS

WARNING / CAUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY INSTRUCTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTRODUCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Feature of this TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
PREPARATION
Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back Panel Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Cover for Wire Arrangement
. . . . . . . . . . . . . . . . . . . . . 12
Attaching the TV to a Wall
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Stand Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VESA Wall Mounting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Desktop Pedestal Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Antenna or Cable Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . 16
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
DVD Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Other A/V Source Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
AV Out Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Digital Audio Output
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
WATCHING TV / CHANNEL CONTROL
Remote Control Key Functions
. . . . . . . . . . . . . . . . . . . . . . . . . 30
Turning On TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Channel Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Volume Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
On-Screen Menus Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
- Auto Scan (EZ Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
- Add / Delete Channel (Manual Scan)
. . . . . . . . . 35
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DTV Signal Strength
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Input Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Input Label
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
SimpLink
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 42
Preset Picture Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
- EZ Picture - Preset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
- Color Tone - Preset.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Manual Picture Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
- EZ Picture - User Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
- Color Tone - User Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . 47
XD - Picture Improvement Technology
. . . . . . . . . . . . . 48
Advanced - Cinema 3:2 Pulldown Mode
. . . . . . . . . . .
49
Advanced - Black (Darkness) Level
. . . . . . . . . . . . . . . . . . . 50
Picture Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
SOUND & LANGUAGE CONTROL
Preset Sound Setting (EZ Sound)
. . . . . . . . . . . . . . . . . . . . . 52
Sound Setting Adjustment - User Mode
. . . . . . . . . . . 53
Balance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
TV Speakers On/Off Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Stereo/SAP Broadcasts Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . 56
Audio Language
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
On-Screen Menus Language Selection
. . . . . . . . . . . . . . 58
Caption/Text
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
- Analog Broadcasting System Captions
. . . . . . .
59
- Digital Broadcasting System Captions
. . . . . . . . 60
Caption Option
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
5
TIME SETTING
Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
- Auto Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
- Manual Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Auto On/Off Timer Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Auto Shut-off Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
- Setting up Your Password
. . . . . . . . . . . . . . . . . . . . . . . . . 67
- Set Password
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
- Lock System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Channel Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
External Input Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Movie & TV Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
- Movie Rating (MPAA)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
- TV Rating Children & General
(for USA only) . . 71
- TV Rating English & French
(for Canada only) . . 72
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Maintenance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Product Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Programming the Remote Control
. . . . . . . . . . . . . . . . . . . 77
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
External Control Through RS-232C . . . . . . . . . . . . . . . . . .82
6

FEATURE OF THIS TV

INTRODUCTION

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is noth­ing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. c. Disposal of this product must be carried out in accordance to the regulations of your local authority.
LG's own special digital image generator, consisting of a full digital image processor, six different main picture quality factors.
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
With HDMI CEC support of LG’s audio/video device connected to the HDMI (high-definition multimedia interface), LG TV with this logo works easily with one remote control.
Manufactured under license from Dolby Laboratories. “
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
It has 2 HDMI ports that connect audio and video devices with one cable and produces the highest quality digital images and sound.

PREPARATION

7
PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.
Twist Holder
Arrange the wires with the
twist holder.
OOppttiioonn EExxttrraass
FFoorr 2266//3322 iinncchheess
4-Bolts for stand assembly
(Refer to p.14)
FFoorr 2266//4422 iinncchheess
Polishing Cloth
Cable Management
2- TV Bracket Bolts
(Refer to p.13)
2- TV Brackets,
2- Wall Brackets
(Refer to p.13)
* Slightly wipe stained spot on the exterior only with the polishing
cloth for the product exterior if there is stain or fingerprint on surface of the exterior.
* Do not wipe roughly when removing stain. Please be cautions of
that excessive pressure may cause scratch or discoloration.
D-sub 15 pin Cable
Owner's Manual
1.5V 1.5V
Owner’s Manual CD Manual
ENTER
T V
I N
P U
T
M
O D E
D
V D
R A
T IO
E X
IT
V O
L
S OUN
D
A
DJU
ST
PICTU
RE
F A V
M U
T E
C H
T I M
E
R
C C
S
A P
M
E N
U
V C
R
P O
W E
R
123
456
789
0
B
A C
K
C O
M
P 1
H
D M
I 1
RGB-PC
S I M P
L I N
K
ENTER
T V
T
V
IN
P U
T
IN
P
U T
M
O D
E
D
V D
R A
T IO
E X
IT
V O
L
S OU
ND
AD
JUS
T
PICT
UR
E
F A V
M U T E
C H
T
IM E
R
C C
S
A
P
M E
N U
V C
R
P
O W
E R
123
456
789
0
B A
C K
C
O M
P 1
H D
M I1
RGB-PC
S
IM P
L IN
K
**
Remote Control,
Batteries
Power Cord
LCD TV PLASMA TV
Owner's Manual
http://www.lgusa.com
www.lg.ca
Copyright© 2007 LGE, All Rights Reserved.
75ohm Round Cable
PREPARATION
8

FRONT PANEL INFORMATION

PREPARATION
Here shown may be somewhat different from your TV.
NOTE: If your product has a protection tape attached, remove the tape. And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).

Front Panel Controls (26 inches)

CH
VOL
ENTER
MENU
INPUT
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode. When the TV is turned on, the indicator blinks green and then illuminates green before the picture is displayed.
CHANNEL (DD,EE)Buttons
VOLUME (
FF,GG
)Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
PREPARATION
9

Front Panel Controls (32/42 inches)

R
CH
VOL
ENTER
MENU
INPUT
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode. When the TV is turned on, the indicator blinks green and then illuminates green before the picture is displayed.
CHANNEL (DD,EE)Buttons
VOLUME (FF,GG)Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
PREPARATION
10

BACK PANEL INFORMATION

PREPARATION
26/32 inches model
Back Connection Panel
R
HDMI IN
HDMI/DVI IN
VIDEO
AUDIO
VIDEO
AUDIO
MONO
( )
S-VIDEO
ANTENNA/
CABLE IN
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
DIGITAL AUDIO
OUT
OPTICAL
1
2
SERVICE
COMPONENT IN
AV OUT
AV IN 1
2
1
8
3
7
6
9
5
10
4
42 inches model
AV IN 2
L/ MONO
R
AUDIO
VIDEO
S-VIDEO
R
HDMI IN
HDMI/DVI IN
VIDEO
AUDIO
VIDEO
AUDIO
MONO
( )
S-VIDEO
ANTENNA/
CABLE IN
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
DIGITAL AUDIO
OUT
OPTICAL
1
2
SERVICE
COMPONENT IN
AV OUT
AV IN 1
2
1
12
8
3
7
6
9
5
10
4
11
Here shown may be somewhat different from your TV.
PREPARATION
11
COMPONENT IN
Connect a component video/audio device to these jacks.
AV OUT
Connect a second TV or monitor.
AV (Audio/Video) IN 1
Connect audio/video output from an external device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
ANTENNA/CABLE IN
Connect over-the air signals to this jack. Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.
HDMI/DVI IN 1, HDMI IN 2
Connect a HDMI (DVI) connection to either input.
RGB IN (PC)
Connect the output from a PC.
AUDIO IN (RGB/DVI)
Connect the audio from a PC or DTV.
Remote Control Port
Connect a wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
For external control devices.
SERVICE
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
AV (Audio/Video) IN 2
Connect audio/video output from an external device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
1
7
8
9
10
11
12
2
3
4
5
6
PREPARATION
12

BACK COVER FOR WIRE ARRANGEMENT

PREPARATION
Connect the cables as necessary. To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT as shown.
How to remove the CABLE MANAGEMENT
GG
Hold the CABLE MANAGEMENT with both hands and pull it backward.
CABLE MANAGEMENT
TWIST HOLDER
GG
Do not hold the CABLE MANAGEMENT when moving the product.
- If the product is dropped, you may be injured or the product may be broken.
NOTE
!
1
2
Bundle the cables using the supplied TWIST HOLDER.
3
Here shown may be somewhat different from your TV.
PREPARATION
13

ATTACHING THE TV TO A WALL

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
Insert the TV brackets and bolts to tighten the product to the wall as shown in the picture.
* Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (not provided as parts of the product, must pur­chase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
PREPARATION
14

STAND INSTALLATION (Only 26/32 inches LCD TV models)

PREPARATION
Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.
Assemble the product stand with the product as shown.
Securely install the 4 bolts provided.
1
2
3
PREPARATION
15

VESA WALL MOUNTING

For proper ventilation, allow a clearance of 4inches on all four sides from the wall.
4 inches
4 inches
4 inches
4 inches
Ensure adequate ventilation by following the clearance recommendations.
CAUTION

DESKTOP PEDESTAL INSTALLATION

GG
Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide.
NOTE
!
R
This product accepts a VESA-compliant mounting interface pad. (optional) There 4 threaded holes are available for attaching the bracket.
100 mm
200 mm
R
400 mm
600 mm
26/32 inches 42 inches
PREPARATION
16

ANTENNA OR CABLE CONNECTION

PREPARATION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wall Antenna Socket
Outdoor Antenna (VHF, UHF)
Cable TV Wall Jack
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the bronze wire when connecting the antenna.
Copper Wire
R
ANTENNA/
CABLE IN
R
ANTENNA/
CABLE IN
R
( )
ANTENNA/
CABLE IN
GG
The TV will let you know when the analog, cable, and digital channel scans are complete.
NOTE
!
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
Antenna
UHF
Signal Amplifier
VHF
3. Using both cable and antenna
Cable TV Wall Jack
Antenna
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
R
ANTENNA/
CABLE IN
Diplexer
(Signal
Combiner)
R

EXTERNAL EQUIPMENT SETUP

17

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
DIGITAL AUDIO
OUT
OPTICAL
AV OUT
AV IN 1
VIDEO
AUDIO
MONO
( )
S-VIDEO
COMPONENT IN
VIDEO
AUDIO
Y L RPB PR

When connecting Component cable

1 2
1. How to connect
Connect the video outputs (Y, P
B, PR
)
of the digital set
top box to the
CC OO MMPP OO NN EENNTT IINN VVIIDD EE OO 11
jacks on
the set. Match the jack colors (Y = green, P
B = blue, and PR = red).
Connect the audio output of the digital set-top box to the
CC OO MMPP OO NN EENNTT IINN AAUUDDIIOO 11
jacks on the set.
2
1
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box. operation
)
Select
CC oo mmpp oonn ee nntt 11
input source by using the
IINNPPUUTT
button on the remote control.
If connected to
CC OO MMPP OO NNEENNTT IINN 22
input, select
CC oo mmpp oonn ee nntt 22
input source.
Signal
480i
480p
720p
10 8 0 i
10 8 0 p
Component 1/2
Yes
Yes
Yes
Yes
Yes
HDMI1/DVI,
HDMI2
No
Yes
Yes
Yes
Yes
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
This part of EXTERNAL EQUIPMENT SETUP mainly use picture for the 42 inches models.
EXTERNAL EQUIPMENT SETUP
18
EXTERNAL EQUIPMENT SETUP

When connecting HDMI cable

Connect the digital set-top box to
HHDDMM II//DD VVII IINN 11
or
HHDDMMII II NN 22
jack on the set.
No separated audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select
HHDDMMII11 //DDVVII
or
HHDD MMII22
input source by using the
IINNPPUUTT
button on the remote control.
2
1
REMOTE
CONTROL
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
SERVICE
ANTENNA/
CABLE IN
HDMI IN
HDMI/DVI IN
1
2
HDMI-DTV OUTPUT
1
GG
When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player output resolution will be automatically set to 720p.
GG
If the device does not support Auto HDMI, you need to set the output resolution appropriately.
NOTE
!
EXTERNAL EQUIPMENT SETUP
19
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN (RGB/DVI)
DIGITAL AUDIO
OUT
OPTICAL
SERVICE
COMPONENT IN
AV OUT
AV IN 1
VIDEO
AUDIO
MONO
( )
S-VIDEO
ANTENNA/
CABLE IN
HDMI IN
HDMI/DVI IN
1
2
L R
DVI-DTV OUTPUT
VIDEO
AUDIO
Connect the DVI output of the digital set-top box to the
HHDDMMII// DDVVII IINN 11
jack on the set.
Connect the audio output of the digital set-top box to the
AAUUDDII OO IINN ((RR GG BB //DD VVII
))
jack on the set.
1. How to connect
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.
)
Select
HHDDMMII11 //DDVVII
input source by using the
IINNPPUUTT
button on the remote control.
2. How to use
2
1
1
2

When connecting HDMI to DVI cable

EXTERNAL EQUIPMENT SETUP
20

DVD SETUP

EXTERNAL EQUIPMENT SETUP

When connecting Component cable

DIGITAL AUDIO
OUT
OPTICAL
AV OUT
AV IN 1
VIDEO
AUDI O
MONO
( )
S-VIDEO
COMPONENT IN
VIDEO
AUDIO
Y L RPB PR
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
YPB PR
Video output ports
on DVD player
Y
Y
Y
Y
P
B
B-Y
Cb
Pb
P
R
R-Y
Cr
Pr
Connect the video outputs (Y, PB
, PR
)
of the DVD to
the
CC OO MMPP OO NN EENNTT II NN VV II DD EE OO 11
jacks on the set.
Match the jack colors (
Y = green, P
B = blue, and PR = red
)
.
Connect the audio outputs of the DVD to the CC OO MMPP OO NN EENNTT II NN AAUUDDIIOO 11
jacks on the set.
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select
CC oo mmpp oonn ee nntt 11
input source by using the
IINNPPUUTT
button on the remote control.
If connected to
CC OO MMPP OO NNEENNTT II NN 22
input, select
CC oo mmpp oonn ee nntt 22
input source.
Refer to the DVD player's manual for operating instructions.
2
1
1 2
EXTERNAL EQUIPMENT SETUP
21

When connecting with an S-Video cable

DIGITAL AUDIO
OUT
OPTICAL
COMPONENT IN
AV OUT
AV IN 1
VIDEO
S-VIDEO
AUDIOUDIO
MONO
( )
VIDEO
AUDIO
L R
S-VIDEO
AUDIO
1
2
REMOT
CONTROL
RS-232C IN
(CONTROL & SERVICE
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
SERVICE
ANTENNA/
CABLE IN
HDMI IN
HDMI/DVI IN
1
2
HDMI-DVD OUTPUT
1
Connect the S-VIDEO output of the DVD to the
SS -- VV II DDEEOO
input on the set.
Connect the audio outputs of the DVD to the
AA UUDD II OO
input jacks on the set.
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select
AA VV 11
input source by using the
IINNPPUUTT
button on the
remote control.
If connected to
AAVV IINN22
, select
AA VV 22
input source.
Refer to the DVD player's manual for operating instructions.

When connecting HDMI cable

Connect the HDMI output of the DVD to the
HHDDMM II//DD VVII IINN 11
or
HHDDMMII II NN 22
jack on the set.
No separated audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Select
HHDDMMII11 //DDVVII
or
HHDD MMII22
input source with using
the
IINNPPUUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
2
1
2
1
GG
When connected, the TV will tell a connected device what resolution it supports and the resolution it prefers. If the device supports this Auto HDMI function, the player out­put resolution will be automatically set to 720p.
GG
If the device does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the DVD to 720p.
NOTE
!
EXTERNAL EQUIPMENT SETUP
22

VCR SETUP

EXTERNAL EQUIPMENT SETUP

When connecting with an antenna

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon.
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
DIGITAL AUDIO
OUT
OPTICAL
S-VID
VIDEO
AUDIO
( )
ANTENNA/
CABLE IN
HDMI IN
HDMI/DVI IN
1
2
L R
S-VIDEO VIDEO
OUTPUT SWITCH
ANT IN
ANT OUT
Wall Jack
Antenna
1
2
Connect the RF antenna out socket of the VCR to the
AANNTTEENNNNAA//CCAABBLL EE IINN
socket on the set.
Connect the antenna cable to the RF antenna in socket of the VCR.
1. How to connect
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
2. How to use
2
1
EXTERNAL EQUIPMENT SETUP
23
GG
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.
CAUTION

When connecting with a RCA cable

GG
The picture quality is improved: compared to normal composite (RCA cable) input.
NOTE
!
DIGITAL AUDIO
OUT
OPTICAL
COMPONENT IN
AV OUT
AV IN 1
S-VIDEO
VIDEO
AUDIO
MONO
( )
L R
S-VIDEO VIDEO
OUTPUT SWITCH
ANT IN
ANT OUT
VIDEO
AUDIO
VIDEO
AUDIO
( )
L R
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
DIGITAL AUDIO
OUT
OPTICAL
COMPONENT IN
AV OUT
AV IN 1
VIDEO
S-VIDEO
AUDIO
MONO
( )
VIDEO
AUDIO
Connect the
AA UUDD II OO/VV II DDEEOO
jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
1. How to connect
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
Select
AA VV 11
input source by using the
IINNPPUUTT
button on
the remote control.
If connected to
AAVV IINN22
, select
AA VV 22
input source.

When connecting with an S-Video cable

Connect the S-VIDEO output of the VCR to the
SS -- VVII DDEEOO
input on the set.
Connect the audio outputs of the VCR to the
AA UUDD II OO
input jacks on the set.
1. How to connect
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR. (
Refer to the VCR owner’s manual.
)
Select
AA VV 11
input source by using the
IINNPPUUTT
button on the
remote control.
If connected to
AAVV IINN22
, select
AA VV 22
input source.
1
2
1
GG
If you have a mono VCR, con­nect the audio cable from the VCR to the
AA UUDD II OO
LL//MM OO NN OO
jack of the set.
NOTE
!
1
1
2
EXTERNAL EQUIPMENT SETUP
24

OTHER A/V SOURCE SETUP

EXTERNAL EQUIPMENT SETUP
AV IN 2
L/ MONO
R
AUDIO
VIDEO
S-VIDEO
L R
VIDEO
Camcorder
Video Game Set
Connect the
AAUUDDIIOO/VVIIDDEEOO
jacks between TV and external equipment. Match the jack colors
.
(
Video = yellow, Audio Left = white, and
Audio Right = red
)
1. How to connect
2. How to use
Select
AA VV 22
input source by using the
IINNPPUUTT
button on the remote control.
If connected to
AAVV IINN11
input, select
AA VV 11
input source.
Operate the corresponding external equipment.
1
1
EXTERNAL EQUIPMENT SETUP
25

PC SETUP

When connecting HDMI to DVI cable

REMOTE
CONTROL
RS-232C IN
(CONTROL & SERVICE
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
DVI-PC OUTPUT AUDIO
ANTENNA/
CABLE IN
HDMI IN
HDMI/DVI IN
1
2
1
2
Connect the DVI output of the PC to the
HHDDMMII// DDVVII
IINN 11
jack on the set.
Connect the PC audio output to the
AAUUDDII OO II NN
((
RR GG BB //DD VVII
))
jack on the set.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select
HHDDMMII11 //DDVVII
input source by using the
IINNPPUUTT
button on the remote control.
2
1
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

When connecting D-sub 15pin cable

RGB OUTPUTAUDIO
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
RGB IN
(PC)
AUDIO IN (RGB/DVI)
DIGITAL AUDIO
OUT
OPTICAL
HDMI IN
1
2
Connect the RGB output of the PC to the
RR GG BB IINN
((
PP CC
))
jack on the set.
Connect the PC audio output to the
AAUUDDII OO IINN
((
RR GG BB //DD VVII
))
jack on the set.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select
RR GG BB -- PPCC
input source by using the
IINNPPUUTT
button
on the remote control.
2
1
1
2
Loading...
+ 63 hidden pages