LG 26LC7D-C, 26LC7DC-UK Service Manual

LCD TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LA75C

MODEL : 26LC7D(C)

26LC7D(C)-UK

website:http://biz.LGservice.com

Internal Use Only

LGE Internal Use Only

- 2 -

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ..................................................................................3

SPECIFICATION ........................................................................................6

ADJUSTMENT INSTRUCTION .................................................................9

TROUBLE SHOOTING ............................................................................14

BLOCK DIAGRAM...................................................................................17

EXPLODED VIEW .................................................................................. 18

REPLACEMENT PARTS LIST ............................................................... 20

SVC. SHEET ...............................................................................................

LGE Internal Use Only

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument’s exposed METALLIC PARTS

Good Earth Ground such as WATER PIPE, CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

LGE Internal Use Only

- 4 -

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500ºF to 600ºF.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500ºF to 600ºF) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500ºF to 600ºF)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS

LGE Internal Use Only

- 5 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

LGE Internal Use Only

- 6 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

4. General Specification(TV)

No. Item Specification Remark

1. Receiving System ATSC/64 & 256 QAM/ NTSC-M

2. Available Channel 1) VHF : 02~13

2) UHF : 14~69

3) DTV : 02-69

4) CATV : 01~135

5) CADTV : 01~135

3. Input Voltage 100 - 240V~, 50/60Hz

4. Market NORTH AMERICA

5. Screen Size 26 inch Wide - 26 inches (582.96 mm)

6. Aspect Ratio 16:9

7. Tuning System FS

8. LCD Module T260XW03V3

9. Operating Environment 1) Temp : 0 ~ 40 deg

2) Humidity : ~ 80 %

10. Storage Environment 1) Temp : -20 ~ 60 deg

2) Humidity : 0 ~ 90 %

1. Application Range.

This specification sheet is applied to the LCD TV used LA75C chassis.

2. Specification

Each part is tested as below without special appointment

2.1 Temperature : 25±5°C(77±9°F), CST : 40±5°C

2.2 Relative Humidity : 65±10%

2.3 Power Voltage : Standard input voltage (100-240V@ 50/60Hz)

• Standard Voltage of each products is marked by models

2.4 Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM .

2.5 The receiver must be operated for about 20 minutes prior to the adjustment.

3. Test method

3.1 Performance : LGE TV test method followed.

3.2 Demanded other specification Safety : UL, CSA, IEC specification

3.3 EMC : FCC, ICES, IEC specification

LGE Internal Use Only

- 7 -

5. Chroma & Luminance Specification

No Item Min Typ Max Unit Remark

1. White peak brightness 350 450 cd/m

HDMI input, full white,

Video Black level = High

400 500 cd/m

MODULE SPEC.

2. Contrast ratio 800:1 1000:1 Non dimming mode

3. Brightness uniformity 1.3

4. Color coordinate RED X 0.633 ± 0.03

Y 0.339 ± 0.03

GREEN X 0.286 ± 0.03

Y 0.610 ± 0.03

BLUE X 0.147 ± 0.03

Y 0.065 ± 0.03

WHITE X 0.276 ± 0.03

Y 0.283 ± 0.03

5. Viewing angle 178 R/L, U/D

6. Color Temperature Standard 8,300 9,300 10,300 <Test Signal>

Cool 10,000 11,000 12,000 HDMI input

Warm 5,500 6,500 7,500 Dynamic/ Cool 85 IRE

6. Component Video Input (Y, PB, PR)

No.

Specification

Remark

Resolution H-freq(kHz) V-freq(Hz)

1. 720*480 15.73 59.94 SDTV ,DVD 480I

2. 720*480 15.73 60.00 SDTV ,DVD 480I

3. 720*480 31.47 59.94 SDTV 480P

4. 720*480 31.50 60.00 SDTV 480P

5. 1280*720 44.96 59.94 HDTV 720P

6. 1280*720 45.00 60.00 HDTV 720P

7. 1920*1080 33.72 59.94 HDTV 1080I

8 1920*1080 33.75 60.00 HDTV 1080I

9 1920*1080 27 24 HDTV 1080P

10 1920*1080 26.97 23.976 HDTV 1080P

11 1920*1080 33.75 30 HDTV 1080P

12 1920*1080 33.71 29.97 HDTV 1080P

13 1920*1080 67.432 59.94 HDTV 1080P

14 1920*1080 67.500 60.00 HDTV 1080P

LGE Internal Use Only

- 8 -

7. RGB Input(PC)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark

PC DDC

1 640*350 31.469 70.08 25.17 DOS

2 720*400 31.469 70.08 28.32 DOS O

3 640*480 31.469 59.94 25.17 VESA(VGA) O

4 800*600 37.879 60.31 40.00 VESA(SVGA) O

5 1024*768 48.363 60.00 65.00 VESA(XGA) O

7 1280*768 47.776 59.87 79.50 CVT(WXGA) O

8 1360*768 47.720 59.799 84.75 CVT(WXGA) O

9 1366*768 47.13 59.65 72

8. HDMI Input (PC/DTV)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark

PC DDC

1. 640*480 31.469 59.94 25.17 VESA(VGA) O

2. 800*600 37.879 60.31 40.00 VESA(SVGA) O

3. 1024*768 48.363 60.00 65.00 VESA(XGA) O

4. 1280*768 47.776 59.87 79.50 CVT(WXGA) O

5. 1360*768 47.720 59.799 84.75 CVT(WXGA) O

6. 1366*768 47.13 59.65 72

DTV

1 720*480 31.50 60 27.027 SDTV 480P

2 720*480 31.47 59.94 27.00 SDTV 480P

3 1280*720 45.00 60.00 74.25 HDTV 720P

4 1280*720 44.96 59.94 74.176 HDTV 720P

5 1920*1080 33.75 60.00 74.25 HDTV 1080I

6 1920*1080 33.72 59.94 74.176 HDTV 1080I

7 1920*1080 67.500 60 148.50 HDTV 1080P

8 1920*1080 67.432 59.939 148.352 HDTV 1080P

9 1920*1080 27.000 24.000 74.25 HDTV 1080P

10 1920*1080 26.97 23.976 74.176 HDTV 1080P

11 1920*1080 33.75 30.000 74.25 HDTV 1080P

12 1920*1080 33.71 29.97 74.176 HDTV 1080P

LGE Internal Use Only

- 9 -

ADJUSTMENT INSTRUCTION

1. Application Range

These instructions are applied to all of the LCD TV, LA75C Chassis.

2. Notice

1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument.

2) Adjustment must be done in the correct order. But it is flexible when its factory local problem occurs.

3) The adjustment must be performed in the circumstance of 25±5°C of temperature and 65±10% of relative humidity if there is no specific designation.

2.4 The input voltage of the receiver must keep 100~220V, 50/60Hz.

2.5 Before adjustment, execute Heat-Run for 30 minutes.

O After Receive 100% Full white pattern (06CH) then

process Heat-run

(Or 6. White Pattern condition of Ez – Adjust)

O How to make set white pattern

A. Press Power ON button of Service Remocon B. Press ADJ button of Service remocon to enter “Ez-

Adjust”. Select "6. WHITE PATTERN" and press

key. And 100% Full White pattern appear.

In this status you can maintain Heat-Run useless any pattern generator.

Notice) If you maintain one picture over 20 minutes

(Especially sharp distinction black with white pattern – 13Ch, or Cross hatch pattern – 09Ch) then it can appear image stick near black level

3. MICOM Download(Option)

3-1. Required Test Equipment

(1) JIG-LEVER TYPE for adjusting: 1EA (2) PC & MONITOR: 2EA (3) BOARD for INTERFACE: IIC & ISP BOARD: 2EA (4) 15P D-SUB CABLE: 2EA (5) Using the 12/15 line of D-SUB 15P

12-SDA/15-SCL

3-2. JIG Connection

3-3. Establishment Program

(1) Establish LGE Monitor Tools v1.1 (2) The program work and it is opened program window as

seen below.

(3) Click the first icon shown in fig.9. The window seen in

fig.10 should appear.

connection

to PC

connection

to PC

- 10 -

3-4. Set Method

(1) MCU Select: MTV412M128 (2) Option

R/W Option: Auto Write(Verity) Jig Option: Myson Transmit Speed: Medium

(3) Check: Just do it with blank micom. (4) PORT

Chose Parallel Port (normal LPT1) Attention: You must chose EPP when select Rom BIAS at LPT

3-5. Download Method

(1) Click the Load File.

(2) Locate and select the correct file from your computer.

(*.hex).

(3) Click the Send.

(4) When you see (ISP COMPLETE) the download is

complete.

4. Using RS-232C

(1) Necessary items before Adjustment items

- Pattern Generator : (MSPG-925FA)

- Adjust 480i Comp1 (MSPG-925FA:model :209 , pattern :65)

- Adjust 1080p Comp1/RGB (MSPG-925FA : model : 225, pattern :65)

(2) Adjustment sequence

- ad 00 00 : Enter the ADC Adjustment mode.

- kb 00 04 : Change the mode to Component1 (No actions)

- ad 00 10 : Adjust 480i Comp1(Change the mode and

adjustment action)

- kb 00 06 : Change to RGB-DTV mode(No action)

- ad 00 10 : Adjust 1080p Comp1/RGB(Change the mode and

adjustment action)

- ad 00 90 : End of the adjustment

(3) Adjustment protocol

LGE Internal Use Only

Order Command Set response

1. Inter the Adjustment mode ad 00 00 d 00 OK00x

2. Change the Source kb 00 04 b 00 OK04x (Adjust 480i Comp1)

kb 00 06 b 00 OK06x (Adjust 1080p Comp1/RGB)

3. Start Adjustment ad 00 10

4. Return the Response OKx ( Success condition )

NGx ( Failed condition )

5. Read Adjustment data (main) (main)

ad 00 20 000000000000000000000000007c007b006dx

(sub) (Sub)

ad 00 21 000000070000000000000000007c00830077x

6. Confirm Adjustment ad 00 99 NG 03 00x (Failed condition)

NG 03 01x (Failed condition)

NG 03 02x (Failed condition)

OK 03 03x (Success condition)

7. End of Adjustment ad 00 90 d 00 OK90x

- 11 -

5. ADC-Set adjustment

5-1. Synopsis

ADC-set is Gain and Black level setting at Analog to Digital converter, and compensate the RGB deviation

5-2. Test Equipment

Service R/C, 801GF(802V, 802F, 802R) or MSPG925FA Pattern Generator (It can output 480i/1080i horizontal 100% color bar pattern signal, and its output level must setting

0.7V±0.1V p-p correctly)’

5-3. Adjustment

(1) ADC 480i Component1 adjustment

1) Set Component 480i mode and 100% Horizontal Color Bar Pattern(HozTV31Bar), then set TV set to Component1 mode and its screen to "NORMAL"

2) After get the signal, wait more a second and enter the "Ez-Adjust" with press ADJ key of Service remocon. After then select "2.ADC 480i Comp1" with navigator button and press "Enter". It is automatically adjustment

3) You can see "ADC Component1 Success" message after Adjustment success Error Messages: When its adjustment is not correct, "ADC Component1 480i Fail" message displayed. If component is not connection "Component1 Not Connected", its format is not 480i then "Not Valid Format", its signal don’t out then "Check Signal Status" message displayed. These messages will be displayed just a second.

(2) ADC 1080p Component1 / RGB adjustment

- Check connection both of Component1 and RGB

- MSPG-925FA -> Model: 225, Pattern 65

1) Set Component 1080p mode and 100% Horizontal Color Bar Pattern(HozTV31Bar), then set TV set to Component1 mode and its screen to "NORMAL"

2) After get the signal, wait more a second and enter the "Ez-Adjust" with press ADJ key of Service remocon. After then select "4.ADC 1080p Comp1/RGB" with navigator button and press "Enter". First, it is automatically adjustment Component1.

3) If adjustment is correctly finished, "ADC Component1 Success" message will be displayed. But adjustment is not correctly finished, "ADC Component1 1080p Fail" message will be displayed.

4) After adjustment Component1 mode, move to RGB-DTV mode automatically and RGB adjustment start. After RGB Adjustment successfully finished, "ADC RGB 1080P Success" message will be displayed.

5) If Adjustment doesn’t success, check conditions all of the adjustment condition and adjustment again. See "Error Messages" sentence.

6) After adjustment finished, press "ADJ" key and exit from Adjustment mode.

6. EDID

(The Extended Display Identification Data)

DDC

(Display Data Channel)

Download

6-1. Summary

It is established in VESA, for communication between PC and Monitor without order from user for building user condition. It helps to make easily use realize "Plug and Play" function.

6-2. Write HDMI EDID data

(1) Using instruments

1) Jig. (PC Serial to D-Sub connection) for PC, DDC adjustment.

2) S/W for DDC recording (EDID data write and read)

3) D-sub jack

4) Additional HDMI cable connection Jig.

(2) Preparing and setting.

1) Set instruments and Jig. Like fig.4), then turn on PC and Jig.

2) Operate DDC write S/W (EDID write & read)

3) It will operate in the DOS mode.

LGE Internal Use Only

<Fig. 3> Device configuration diagram for HDMI EDID Data input

<Fig. 1> Adjustment Mode

<Fig. 2> Adjustment Pattern: 480i/1080P 60Hz HozTV30 Bar Pattern

LCD TV SET

(or Digital Board)

+ 25 hidden pages