LG 22MB65PM, 22MB65PM-B User Manual

ENGLISH

OWNER’S MANUAL

IPS LED MONITOR (LED LCD MONITOR)
Please read this manual carefully before operating your set and retain it for future reference.
22MB65PM 24MB65PM
www.lg.com
TABLE OF CONTENTS
2
ENGLISH
ENG

CONTENTS

3 ASSEMBLING AND PREPAR-
ING
3 Unpacking
4 Parts and buttons
5 Setting up the Monitor set
5 - Attaching the Stand Base
5 - Detaching the stand base
6 - Detaching the stand body
6 - Using the cable holder
7 - Mounting on a table
7 - Adjusting the angle
8 - Adjusting the stand height
8 - Using the Kensington locking device
9 - Swivel stand
9 - Using the Pivot function
10 - Mounting on a wall
22 TROUBLESHOOTING
24 SPECIFICATIONS
24 22MB65PM
25 24MB65PM
26 Preset Modes (Resolution)
26 Indicator
27 PROPER POSTURE
27 Proper posture for using the Monitor set.
11 USING THE MONITOR SET
11 Connecting to a PC
11 - D-SUB connection
11 - DVI-D connection
13 - Peripheral device connection
14 CUSTOMIZING SETTINGS
15 Customizing Settings
15 - Menu Settings
16 - Picture
17 - Color
18 - Display
19 - Others
20 READER SETTING
21 SUPER ENERGY SAVING SET-
TING

ASSEMBLING AND PREPARING

3
ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
CD(Owner's Manual) /
Card
D-SUB Cable
(This cable is not included in all
countries.)
(This cable is not included in all
DVI-D Cable
countries.)
ENGLISH
ENG
Power Cord
Audio Cable
( Depending on the country )
Stand Base
One Screw
Cable Holder
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
y
Any damages or injuries by using unapproved accessories are not covered by the warranty.
y
NOTE
The accessories supplied with your product may vary depending on the model.
y
Product specifications or contents in this manual may be changed without prior notice due to upgrade
y
of product functions.
ENGLISH
ENG
ASSEMBLING AND PREPARING
4

Parts and buttons

Power Indicator
LED On : Power is on
y
LED Off: Power is off
y
Front Side Buttons
Input Connectors (See p.11 to 13)See p.11 to 13) to 13)13))
(Power Button)
ASSEMBLING AND PREPARING
5

Setting up the Monitor set

Attaching the Stand Base

Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
CAUTION
To protect the screen from scratches, cover
y
the surface with a soft cloth.
Check the
2
the stand body, then mount the the
position (at the front and rear)
stand body
as shown in the figure.
Stand Body
stand base
of
on

Detaching the stand base

Place the monitor's screen face down.
1
To protect the screen from scratches, cover the surface with a soft cloth.
Using a coin, turn the screw in the stand base
2
counterclockwise. Detach the
stand body
the
.
stand base
Stand Body
ENGLISH
ENG
from
Using a coin, turn the screw clockwise to se-
3
cure the
stand base.
Stand Base
Stand Base
Stand Base
CAUTION
The components appearing in the illustra-
y
tions may look different from the actual prod­uct. Do not carry the monitor upside-down as this
y
may cause it to fall off its stand, resulting in damage or injury. To avoid damaging the screen when lifting
y
or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnec­essary pressure on the screen. Only remove the tape and the locking pin
y
when the monitor is mounted on the stand base and is in an upright position. Otherwise, the stand body may protrude, which may lead to injury.
ENGLISH
ENG
ASSEMBLING AND PREPARING
6

Detaching the stand body

Place the monitor's screen face down. To
1
protect the screen from scratches, cover the surface with a soft cloth.
Using a screwdriver, remove the four screws
2
and detach the stand from the monitor.

Using the cable holder

Fix the Knob (Cable holder) to the
1
Hole(Hingebody). Use one screw to fix the Cable Holder and
2
monitor set.
3
Close the Cable holder.
ASSEMBLING AND PREPARING
7

Mounting on a table

Lift the monitor and place it on the table in an
1
upright position.
Install at least ensure sufficient ventilation.
Connect the Power cord to the monitor, then
2
1
plug the power cord into the wall outlet. (Before connect please check the “ON/OFF” knob in “O” state).
2
Press the “ON/OFF” knob in “ ” state (Open the power).
10 cm
10 cm
away from the wall to
10 cm
10 cm
10 cm

Adjusting the angle

Place the monitor mounted on the stand base
1
in an upright position.
Adjust the angle of the screen. The angle of
2
the screen can be adjusted up to 5° forwards and 20° backwards for a comfortable viewing experience.
Front SideRear Side
WARNING
To avoid injury to the fingers when adjusting
y
the screen, do not hold the lower part of the monitor's frame as illustrated below.
ENGLISH
ENG
Press the (Power) button on the front of the
3
monitor to turn on the monitor.
CAUTION
Unplug the power cord prior to moving or
y
installing the monitor. There is risk of electric shock.
Be careful not to touch or press the screen
y
area when adjusting the angle of the monitor.
ASSEMBLING AND PREPARING
8
ENGLISH
ENG

Adjusting the stand height

Place the monitor mounted on the stand base
1
in an upright position.
Remove the
2
of the
pin.
Stand Body
tape
stand body,
attached at the bottom rear
then pull out the
Tape
Locking Pin
locking

Using the Kensington locking device

The connector for the Kensington lock is located on the rear of the monitor. For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http://www.kensington.com.
Connect the monitor to the table with the Kensing-
ton lock cable.
The height can be adjusted up to
3
120 mm
CAUTION
Once the pin is removed, it is not necessary
y
to re-insert it to adjust the height.
WARNING
Do not put your finger be-
y
tween the screen and the base (chassis) when adjust­ing the screen's height.
.
120.0mm
NOTE
Using the Kensington lock is optional. The
y
accessories can be purchased at your local electronics store.

Swivel stand

Image shown may differ from your Monitor
y
set.
Swivel 355 degrees and adjust the angle of the
1
Monitor set to suit your view.
ASSEMBLING AND PREPARING
Be careful with the cables when rotating the
3
screen.
9
ENGLISH
ENG

Using the Pivot function

The pivot function allows you to rotate the screen 90 degrees clockwise.
Lift the monitor to its highest height to utilize
1
the Pivot function.
Landscape & Portrait : You can rotate the panel
2
90° clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.
Head section
Stand section
Loading...
+ 19 hidden pages