Please read this manual carefully before operating
your set and retain it for future reference.
Write the model number and serial number from the
label on the back cabinet on the front or back of
this manual.
P/NO : MFL41469212 (0808-REV03)
Printed in Korea
www.lge.com
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
WARNING / CAUTION
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
1
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
1
Clean only with dry cloth.
2
Do not block any ventilation openings. Install in
3
accordance with the manufacturer’s instructions.
Protect the power cord from being walked on
6
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
7
the manufacturer.
Use only with the cart, stand, tripod, bracket,
8
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Do not install near any heat sources such as
4
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
Do not defeat the safety purpose of the polarized
5
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Unplug this apparatus during lighting storms or
9
when unused for long periods of time.
Refer all servicing to qualified service personnel.
10
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
2
Never touch this apparatus or antenna during a
11
thunder or lighting storm.
When mounting a TV on the wall, make sure not to
12
install the TV by the hanging power and signal
cables on the back of the TV.
Do not allow an impact shock or any objects to fall
13
into the product, and do not drop onto the screen
with something.
CAUTION concerning the Power Cord :
14
It is recommend that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the
TV.
WARNING - To reduce the risk of fire or electrical
15
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.
Do not expose to dripping or splashing and do not
16
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
GGRROOUUNNDDIINNGG
17
Ensure that you connect the earth ground wire to
prevent possible electric shock. (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding
methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.
Mains plug is the disconnecting device. The plug
must remain readily operable.
Power
Supply
Keep the product away from direct sunlight.
19
3
Cleaning
20
When cleaning, unplug the power cord and scrub
gently with a soft cloth to prevent scratching. Do not
spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
Moving
21
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.
Ventilation
22
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in
excessively dusty places.
If you smell smoke or other odors coming from the
23
TV or hear strange sounds, unplug the power cord
contact an authorized service center.
Do not press strongly upon the panel with a hand or
24
sharp object such as nail, pencil or pen, or make a
scratch on it.
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is
nothing wrong with TV.
■
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.
■
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.
c. Disposal of this product must be carried out in accordance to the regulations of your local authority.
6
PREPARATION
1.5V 1.5V
123
456
78
0
9
VOLVOL
CH
CH
EN
T
ER
M
EN
U
Q.V
IE
W
SL
EE
P
R
E
SO
UN
D
RA
T
IO
FA
V
MU
TE
OG
MEMORY
/ERASE
CA
PT
ION
IN
PU
T
123
456
78
0
9
VOLVOL
CH
CH
E
N
T
E
R
P
O
W
E
R
M
E
N
U
Q
.V
IE
W
S
L
E
E
P
R
A
T
I
O
M
T
S
F
A
V
M
U
T
E
A
.
P
R
O
G
CAPTION
T
V
IN
P
U
T
MEMORY/ERASE
S
O
U
N
D
P
I
C
T
U
R
E
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
PREPARATION
Owner’s ManualPower Cord
Remote Control,
Batteries
Cable Management Clip
Polishing Cloth
(This feature is not available
for all models.)
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stain. Please be
cautions of that excessive pressure may cause scratch or
discoloration.
Protection Cover
7
PREPARATION
FRONT PANEL INFORMATION
■
Image shown may differ from your TV.
■
PREPARATION
NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your product, use it).
INPUT
Button
INPUT
MENU
Button
MENU
ENTER
Button
ENTER
VOLUME
FF,GG
(
) Buttons
VOLCH
CHANNEL
EE,DD
(
) Buttons
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
Remote Control Sensor
POWER Button
8
BACK PANEL INFORMATION
■
Image shown may differ from your TV.
8
PREPARATION
1
HDMI/DVI IN
4
RS-232C IN
(CONTROL & SERVICE)
1
HDMI/DVI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI to
DVI cable (not included)
2
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red
and white for audio.
3
RGB(PC) IN
VIDEO
VIDEO
AUDIO
(RGB/DVI) IN
AV IN
AUDIO
(
)
MONO
COMPONENT IN
5
ANTENNA IN
Connect over-the air signals to this jack.
6
AV (Audio/Video) IN
Analog composite connection. Supports standard
definition video only (480i).
S-VIDEO
Better quality than standard composition.
Supports standard definition video only (480i).
7
Headphone INPUT
Plug the headphone into the headphone socket.
S-VIDEO
AUDIO
5
ANTENNA IN
6
H/P
7
2
3
RGB (PC) IN
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO (RGB/DVI) IN
1/8” headphone jack for analog PC audio input.
4
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
8
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
9
PREPARATION
STAND INSTALLATION
■
Image shown may differ from your TV
PREPARATION
Carefully place the TV screen side down on a
1
cushioned surface to protect the screen from
damage.
Assemble the parts of the
2
CCOOVVEERR BBAASSEE
BBOODDYY
Assemble the TV as shown.
3
CCOOVVEERR BBAASSEE
into a
SSTTAANNDDBBOODDYY
of the TV. Insert the
until clicking sound.
with
SSTTAANNDD
SSTTAANNDDBBOODDYY
CCOOVV EERRBBAASSEE
10
!
CABLE MANAGEMENT
■
Image shown may differ from your TV
Connect the cables as necessary.
1
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as
2
shown.
PREPARATION
CABLE MANAGEMENT CLIP
3
Fit the CABLE MANAGEMENT CLIP as shown.
How to remove the
CABLE MANAGEMENT CLIP
Hold the CABLE MANAGE-
GG
MENT CLIP with both hands
and pull it backward.
NOTE
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
GG
- If the TV is dropped, you may be injured or the product may be broken.
11
PREPARATION
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
PREPARATION
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
4 inches
CAUTION
4 inches
Ensure adequate ventilation by following the clearance recommendations.
GG
Do not mount near or above any type of heat source.
GG
4 inches
4 inches
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you
use an LG brand wall mount when mounting the TV to a wall.
4 inches
4 inches
12
4 inches
4 inches
4 inches
PROTECTION COVER
■
Image shown may differ from your TV.
Loose the bolts from TV.
1
PREPARATION
2
3
Bend the
Insert the
HHIINNGGEEBB OODD YY
PPRROO TT EECCTTIIOONNCCOOVVEERR
and pull it backward.
HHIINNGGEEBB OODD YY
into the TV.
PPRROO TT EECCTTIIOONNCCOOVVEE RR
Fix the 4 bolts securely using the holes in the
4
back of the TV.
13
PREPARATION
12
0
3
0
POSITIONING YOUR DISPLAY
■
Here shown may be somewhat different from your TV.
■
Adjust the position of the panel in various ways for maximum comfort.
PREPARATION
• Tilt range
KENSINGTON SECURITY SYSTEM
- The TV is equipped with a Kensington Security System connector on
the back panel. Connect the Kensington Security System cable as
shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington
Security System.
For further information, contact
the internet homepage of the Kensington company. Kensington sells
security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
■
ANTENNA IN
ANTENNA IN
ANTENNA IN
To prevent damage do not connect to the power outlet until all connections are made between the devices.
■
Image shown may differ from your TV.
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Antenna
Socket
Outdoor
RF Coaxial Wire (75 ohm)
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
2. Cable
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
PREPARATION
Copper Wire
Be careful not to bend the bronze wire
when connecting the antenna.
■
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
■
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■
If the antenna is not installed properly, contact your dealer for assistance.
UHF
Antenna
VHF
Signal
Amplifier
15
EXTERNAL EQUIPMENT SETUP
Y
P
B
P
R
L
R
ANTEN
RGB(PC) IN
IN
AUDIO
(RGB/DVI) IN
AUDIO
COMPONENT IN
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
H/P
S-VIDEO
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals with an external digital set-top box. If you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
EXTERNAL EQUIPMENT SETUP
Component Connection
1. How to connect
)
Connect the video outputs (Y, P B, PR
1
top box to the
CCOOMMPPOONNEE NNTT IINNVVII DD EEOO
the TV. Match the jack colors (Y = green, P
R = red).
P
of the digital set-
jacks on
B = blue, and
Connect the audio output of the digital set-top box to
2
the
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box. operation
■
Select the
IINNPPUUTT
Signal
480i
576i
480p
576p
720 p
1080i
10 8 0 p
CCOOMMPPOONNEE NNTT IINNAAUUDDIIOO
CCoommppoonneenntt
input source on the TV using the
button on the remote control.
Component
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(Only 50Hz, 60Hz)
(Only 50Hz, 60Hz)
jacks on the TV.
HDMI/DVI
No
No
Yes
Yes
Yes
Yes
Yes
1
2
)
16
HDMI Connection
RGB(PC) IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO
(RGB/DVI)
COMPONEN
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
HDMI/DVI IN
HDMI OUTPUT
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the digital set-top box to
1
jack on the TV.
No separate audio connection is necessary.
2
HDMI supports both audio and video.
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box.
■
Select the
IINNPPUUTT
HHDDMMII//DDVVII
input source on the TV using the
button on the remote control.
HHDDMMII// DD VVIIII NN
)
HDMI-DTV
720x480p
Resolution
1
Horizontal Vertical
Frequency(kHz)Frequency(Hz)
31.4759.94
31.5060.00
720x576p
1280x720p
1920x1080i
1920x1080p
31.2550.00
44.9659.94
45.0060.00
37.5050.00
33.7259.94
33.7560.00
28.12550.00
67. 43259.94
67.5060.00
56.2550.00
17
EXTERNAL EQUIPMENT SETUP
!
RGB(PC) IN
RS-232C IN
S-VIDE
AUD
COMPONENT IN
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
HDMI/DVI IN
L
R
DVI OUTPUT
AUDIO
(RGB/DVI) IN
ANTENNA IN
AUDIO
H/P
DVI to HDMI Connection
1. How to connect
Connect the DVI output of the digital set-top box to the
EXTERNAL EQUIPMENT SETUP
1
HHDDMMII//DDVVIIIINN
jack on the TV.
Connect the audio output of the digital set-top box to
2
AAUUDDIIOO ((RR GG BB//DDVV II ))II NN
the
jack on the TV.
2. How to use
■
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top box. operation
■
Select the
IINNPPUUTT
HHDDMMII//DD VVII
input source on the TV using the
button on the remote control.
1
2
)
NOTE
A DVI to HDMI cable or adapter is required for this
GG
connection. DVI doesn't support audio, so a separate
audio connection is necessary.
HEADPHONE SETUP
You can listen to the sound through the headphone.
1. How to connect
1
2
Plug the headphone into the headphone socket.
To adjust the headphone volume, press the
button. If you press the
GG
from the headphone is switched off.
MMUUTT EE
button, the sound
VVOOLL
FF
or
18
DVD SETUP
Y
P
B
P
R
L
R
ANTEN
RGB(PC) IN
AUDIO
(RGB/DVI) IN
AUDIO
COMPONENT IN
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
H/P
S-VIDEO
IN
Component Connection
1. How to connect
Connect the video outputs (Y, P
1
CCOOMMPPOONNEE NNTT IINNVVIIDDEEOO
the
the jack colors (Y = green, P
)
of the DVD to
B, PR
jacks on the TV. Match
B = blue, and PR = red
EXTERNAL EQUIPMENT SETUP
)
.
Connect the audio outputs of the DVD to the
2
PPOONNEENNTTIINNAAUUDDIIOO
jacks on the TV.
CC OOMM--
1
2. How to use
■
Turn on the DVD player, insert a DVD.
■
Select the
IINNPPUUTT
■
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
CCoommppoonneenntt
input source on the TV using the
button on the remote control.
Video output ports
on DVD player
YPBPR
B-Y
Cb
Pb
PB
R-Y
Y
Y
Y
Y
P
R
Cr
Pr
2
19
EXTERNAL EQUIPMENT SETUP
S-VIDEO
ANTENNA I
RGB(PC) IN
AUDIO
(RGB/DVI) IN
S-VIDEO
COMPONENT IN
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
H/P
AUDIO
LR
AUDIO
RGB(PC) IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO
(RGB/DVI) IN
COMPONENT
VIDEO
VIDEO
AUDIO
MONO
( )
AV IN
HDMI/DVI IN
HDMI OUTPUT
S-Video Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the S-VIDEO output of the DVD to the
1
VVIIDDEEOO
input on the TV.
Connect the audio outputs of the DVD to the
2
input jacks on the TV.
2. How to use
■
Turn on the DVD player, insert a DVD.
■
Select the
AAVV
input source on the TV using the
button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
HDMI Connection
1. How to connect
Connect the HDMI output of the DVD to the
1
IINN
jack on the TV.
SS --
AAUUDDII OO
IINNPPUUTT
HHDDMMII//DDVVII
2
1
20
2. How to use
No separated audio connection is necessary.
2
HDMI supports both audio and video.
■
Select the
IINNPPUUTT
■
Refer to the DVD player's manual for operating instructions.
HHDDMMII//DD VVII
button on the remote control.
input source on the TV using the
1
VCR SETUP
LR
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
ANTENNA INANTENNA IN
N
S-VIDEO
AUDIO
IN
H/P
■
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■
If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.
This phenomenon is common to all TVs and is not covered by warranty.
Antenna Connection
1
2
Wall Jack
Antenna
EXTERNAL EQUIPMENT SETUP
1. How to connect
Connect the RF antenna out socket of the VCR to the
1
Connect the antenna cable to the RF antenna in socket of the VCR.
2
2. How to use
■
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
■
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
AANNTTEENNNNAAIINN
socket on the TV.
)
21
Loading...
+ 51 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.