<![endif]>ENGLISH
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODEL
22EA53R
23EA53R
www.lg.com
<![endif]>ENGLISH
2 TABLE OF CONTENTS
3 |
ASSEMBLING AND PREPAR- |
24 |
SPECIFICATIONS |
||
|
ING |
|
|
|
|
|
24 |
22EA53R |
|||
|
|
||||
3 |
Unpacking |
25 |
23EA53R |
||
4 |
Parts and buttons |
26 |
Preset Modes (Resolution) |
||
5 |
Setting up the Monitor set |
26 |
Indicator |
||
5 |
- Attaching the Stand Base |
27 |
|
||
5 |
- Detaching the Stand Base |
PROPER POSTURE |
|||
6 |
- Mounting on a table |
||||
|
|
|
|||
27 |
Proper posture for using the Monitor set. |
||||
6 |
- Using the cable holder |
||||
|
|
|
8- Mounting on a wall
9USING THE MONITOR SET
9 Connecting to a PC
9 - D-SUB connection
9 - DVI-D connection
11 CUSTOMIZING SETTINGS
12Customizing Settings
12- Menu Settings
13-Picture
14-Color
15-Display
16-Others
17MY KEY Setting
18FUNC. Setting
18-Picture Mode
19-SUPER ENERGY SAVING
20-DUAL DISPLAY
20-DUAL WEB
21-MY KEY Setting
22 TROUBLESHOOTING
ASSEMBLING AND PREPARING 3
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
<![endif]>ENGLISH
CD(Owner's Manual) / |
D-SUB Cable |
|
Card |
||
|
Power Cord |
AC-DC Adapter |
( Depending on the country )
DVI-D Cable
(This cable is not included in all countries.)
or
AC-DC Adapter
( Depending on the country )
Stand Body |
Stand Base |
CAUTION
yyDo not use any unapproved accessories to ensure the safety and product life span.
yyAny damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
yyThe accessories supplied with your product may vary depending on the model.
yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4 ASSEMBLING AND PREPARING
<![endif]>ENGLISH
Power Indicator yyLighting On: Turned on yyLighting Off: Turned off
(Power Button)
Button (See p.11)
Connection panel (See p.9)
ASSEMBLING AND PREPARING 5
1Place the Monitor set with the screen side down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.
21 Attach the Stand Body to the monitor set.
2 Attach the Stand Base.
3 Tighten the screw to the right with a coin.
1Place the Monitor set with the screen side down on a flat and cushioned surface.
21 Pull out the Stand Body and Stand Base from the monitor set.
2Turn the screw to the left with a coin.
3Pull out the Stand Base.
Stand Body
Stand Body
Stand Base
Stand Body
Stand Base |
Stand Base |
CAUTION
yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 ASSEMBLING AND PREPARING
1Lift and tilt the Monitor set into its upright position on a table.
Leave a 10 cm (minimum) space from the wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
3Press (Power) button on the bottom switch panel to turn the power on.
CAUTION
Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.
2 Connect the AC-DC Adapter and Power Cord to a wall outlet.
Cable holder
or
|
|
ASSEMBLING AND PREPARING 7 |
||
WARNING |
|
|
||
|
Using the Kensington security system |
|
When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.
Do
Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.
NOTE
+20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.
Connect the Kensington security system cable between the Monitor set and a table.
NOTE
The Kensington security system is optional. You can obtain it from most electronics stores.
<![endif]>ENGLISH
Front |
Rear |
<![endif]>ENGLISH
8 ASSEMBLING AND PREPARING
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
10 cm
10 cm
10 cm
10 cm
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.
1Please, Use the screw and wall mount interface in accordance with VESA Standards.
2If you use screw longer than standard, the monitor might be damaged internally.
3If you use improper screw, the product might be damaged and drop from mounted position. In
this case, LG Electronics is not responsible for it.
4VESA compatible.
5Please use VESA standard as below.
yy784.8 mm (30.9 inch) and under
*Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
yy787.4 mm (31.0 inch) and above
*Please use VESA standard wall mount pad and screws.
Model |
22EA53R |
|
23EA53R |
VESA (A x B) |
75 x 75 |
Standard screw |
M4 |
Number of screws |
4 |
CAUTION
yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.
yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.
yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel.
yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.
yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper
accessory are not covered by the warranty.
NOTE
yyUse the screws that are listed on the VESA standard screw specifications.
yyThe wall mount kit will include an installation manual and necessary parts.
yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.
yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.
yyFor more information, refer to the instructions supplied with the wall mount.
USING THE MONITOR SET 9
yyYour Monitor set supports Plug & Play*.
*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.
Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.
Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.
NOTE
yyWhen using a D-Sub signal input cable connector for Macintosh
yyMac adapter
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.
<![endif]>ENGLISH