LG 21FU3RG-TZ, 21SA1RG-T4, 21SA3RG-T4, 21SB4RG-T4, 21SC3RG-T4 Owner’s Manual

OWNER’S MANUAL

Colour Television

Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.

Model number : Serial number :

P/NO :MFL67020302-EN (CW81AB)(1010-REV00)

www.lg.com

Power

This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs. Press the POWER button on the front panel or side panel to turn off the TV when the TV set is not being used for a long time.It is recommended to remove the plug from the wall outlet(Power point).

Disconnecting device from mains

Mains plug is the disconnecting device. The plug must remain readily operable

Warning

To prevent fire or shock hazard, do not expose the set to rain or moisture.Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.

Service

Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.

Aerial

Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.

Location

Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.

Installation

Connection of external equipment

Aerial socket

1. Connect the RF out socket of the VCR to the aerial socket on the back of the set.

2. Connect the aerial cable to the RF aerial in socket of the VCR.

3. Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.

4. Select the programme number where the VCR channel is stored.

5. Press the PLAY button on the VCR.

Audio/Video in/out sockets (option)

1. Connect the audio/video out sockets of the VCR to audio/video in sockets of the set and in sockets of the VCR to RF OUT sockets of the set.

2. If the VCR is connected to the AV sockets on the set, press the TV/AVbutton to select AV1 or AV2.

3. Press the PLAY button on the VCR.The VCR playback picture appears on the screen. You can also record programmes received by the TV on video tape via audio/video out sockets.

Note : If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set.

Euro scart socket (option)

1. Connect the Euro scart socket of the VCR to the Euro scart socket of the set.

2. Press the PLAY button on the VCR. If your VCR outputs a switching voltage when connected to Euro scart socket, the set will switch to AV 1 mode automatically. But if you

want to keep on watching TV mode, press the

DD / EE

or NUMBER buttons.Otherwise press the TV/AV button on the remote control handset to select AV 1 The VCR playback pic- ture appears on the screen.

You can also record programmes received by the

TV on video tape.

Note : Signal type RGB, i.e. the signals red, green and blue can only be selected for the Euro scart socket. These signals are transmitted, for example, by a pay TV decoder, game machine or photo CD unit, etc.

Component in sockets (option)

1. Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or YB-Y R-Y) of the COMPONENT (480i) to the COMPONENT INPUT sockets (Y PB PR) on the set.

2. Connect the audio cable from the COMPONENT to AUDIO IN sockets of AV IN2.

3. Press the TV/AVbutton to select COMPONENT.

4. Press the PLAY button on the COMPONENT. The COMPONENT playback picture appears on the screen.

Headphone socket (option)

You can listen to the sound through the headphones. To adjust the headphone volume, press the F / G button. If you press the MUTE button, the sound from the headphone’s is switched off.

Location and function of controls

Battery installation

The remote control handset is powered by AAA type batteries.Install batteries as indicated by the polarity symbols ( and ) marked inside the compartment.

Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time

Remote control handset

Before you use the remote control handset, please install the batteries.

1. POWER

switches the set on from standby or off to standby.

2. NUMBER BUTTONS

Switches the set on from standby or directly select a number.

3. MENU

selects a menu.

DD / EE

(Programme Up/Down)

selects a programme or a menu item. switches the set on from standby.

FF / GG

(Volume Up/Down)

adjusts the volume. adjusts menu settings.

accepts your selection or displays the current mode.

5. TELETEXT BUTTONS (option)

These buttons are used for teletext. For further details, see the ‘Teletext’ section.

SLEEP

sets the sleep timer.

7. FAVOURITE

/*(option)

selects a favorite programme.

EYE/*(option)

switches the eye function on or off.

9. MUTE( )

switches the sound on or off.

10. TV/AV( )

selects TV or AV mode. switches the set on from standby. exits the Teletext mode.

11.

I/II/*(option)

selects the language during dual language broadcast. selects the sound output (option).

12. Q.VIEW (or YELLOW)

returns to the previously viewed programme.

13.

LIST/*(or BLUE)(option)

displays the programme table.

: No function

COLOURED BUTTONS : These buttons are

used for teletext (only TELETEXT models) or programme edit.

Front panel

MAIN POWER (ON/OFF)

switches the set on or off.

POWER/STANDBY INDICATOR

illuminates brightly when the set is in standby mode.dims when the set is switched on.

REMOTE CONTROL SENSOR

Note : Only use the supplied remote control

handset. (When you use others, they will not be able to function.)

selects a menu.

accepts your selection or displays the current mode.

FF / GG

(Volume Down/Up)

adjusts the volume. adjusts menu settings.

DD / EE

(Programme Up/Down)

selects a programme or a menu item. switches the set on from standby.

EYE (option)

adjusts picture according to the surrounding conditions.

Note :

What is shown here may be somewhat dif-

ferent from your set or can not be supplied on your area.

Location and function of controls

UPDATE/ HOLD/

LIST/

FAVOURITE/

5 6

+ 5 hidden pages