LG 21FU1RLM Owner’s Manual
Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number |
: |
Serial number |
: |
P/NO : MFL42111511 (CW81A/B, MKJ33981403/4/5/6 TX )
Contents
Installation.......................................................... |
2 |
Connection of external equipment.................. |
2 |
Location and function of controls................... |
3 |
Basic operation................................................. |
5 |
On screen menus.............................................. |
5 |
Setting up TV stations...................................... |
6 |
Picture adjustment............................................ |
7 |
Sound adjustment............................................. |
8 |
Time setting....................................................... |
9 |
Other functions................................................. |
9 |
PIP operation (option)..................................... |
10 |
Teletext (option)............................................... |
10 |
Troubleshooting check list |
|
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
DISCONNECTING DEVICE FROM MAINS
-Mains plug is the disconnecting device. The plug must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture.
Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.
Service
Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly,
unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
Note:
To remove dirt or fingerprint on the surface of your TV, please rub with a line-free cloth supplied in the accessory.Do not pose too much pressure in cleaning so as to prevent any risk of damage to the product.
Connection of external equipment
Aerial socket
1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel on the programme
number 0 using the ‘Manual programme tuning’ section.
4.Select the programme number where the VCR channel is stored.
5.Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1.Connect the audio/video out sockets of the VCR to audio/video in sockets of the set.
2.If the VCR is connected to the AV sockets on the set, press the TV/AV button to select AV
(or AV1), or AV 2.
3.Press the PLAY button on the VCR.
You can also record programmes received by the TV on video tape via audio/video out
sockets.
Euro scart socket (option)
1.Connect the Euro scart socket of the VCR to the Euro scart socket of the set.
2.Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when connected to Euro scart socket, the set will switch to AV (or AV1) mode automatically. But if you want to keep on watching TV mode,
press the D / E or NUMBER buttons.
Otherwise press the TV/AV button on the remote control handset to select AV (or AV1). You can also record programmes received by the TV on video tape.
Component in sockets (option)
1.Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the DVD player to the COMPONENT INPUT sockets (Y PB PR) on the set.
2.Connect the audio cable from the DVD player to AUDIO IN sockets of AV (or AV1).
3.Press the TV/AV button to select COMPONENT.
4.Press the PLAY button on the DVD player.
The COMPONENT playback picture appears on the screen.
S-video / Audio in sockets (S-AV) (option)
When connecting the S-video socket of the VCR to the S-VIDEO socket of the set, the picture quality will be further improved.
1.Connect the S-video socket of the VCR to the S-VIDEO socket of the set.
2.Connect the audio cable from the VCR to the
AUDIO sockets of the set.
3.Select AV2 by pressing the TV/AV button repeatedly.
4.Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If both S-VIDEO and VIDEO sockets have been connected to the VCR simultaneously, only the S-VIDEO can be received.
Headphone socket (option)
You can listen to the sound through the headphones. To adjust the headphone volume, press
the F / G button.
If you press the MUTE button, the sound from the headphone’s is switched off.
2
Location and function of controls
All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the front panel of the set.
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
1.POWER
switches the set on from standby or off to standby.
2.NUMBER BUTTONS
switches the set on from standby or directly select a number.
3.MENU
selects a menu.
4.D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby. scans programmes automatically.
F / G (Volume Up/Down) adjusts the volume. adjusts menu settings.
OK
accepts your selection or displays the current mode.
5.TELETEXT BUTTONS (option) these buttons are used for teletext.
for further details, see the ‘Teletext’ section.
6.SLEEP
sets the sleep timer.
7.PIP BUTTONS (option) PIP
switches the sub picture on or off.
PR +/-
selects a programme for the sub picture.
SWAP
alternates between main and sub picture.
INPUT
selects the input mode for the sub picture.
SIZE
adjusts the sub picture size.
STILL
freezes motion of the sub picture.
POSITION
relocates the sub picture in clockwise direction.
1 |
|
|
|
10 |
|
|
11 |
|
1 |
2 |
3 |
2 |
4 |
5 |
6 |
|
7 |
8 |
9 |
3 |
|
0 |
8 |
|
|
PR |
|
4 |
VOL |
OK |
VOL |
|
|
PR |
|
5 |
|
|
|
6 |
|
|
7 |
|
|
|
|
9 |
|
|
12 |
|
|
|
(With TELETEXT / PIP)
PR
VOL |
OK |
VOL |
|
PR |
|
|
UPDATE/ |
HOLD/ |
5
(With TELETEXT / Without PIP)
3
Location and function of controls
1 |
|
|
|
10 |
|
|
11 |
|
|
Q.VIEW |
13 |
|
|
LIST |
|
|
|
|
14 |
|
1 |
2 |
3 |
2 |
4 |
5 |
6 |
|
7 |
8 |
9 |
3 |
|
0 |
8 |
|
|
PR |
|
4 |
VOL |
OK |
VOL |
|
|
|
|
|
|
PR |
|
|
|
|
12 |
6 |
|
|
9 |
(Without TELETEXT / PIP)
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
|
0 |
|
|
PR |
|
VOL |
OK |
VOL |
|
PR |
|
7 |
|
|
(With PIP / Without TELETEXT)
8.FAVOURITE
selects a favorite programme.
9.EYE/* (option)
switches the eye function on or off.
10.MUTE 
switches the sound on or off.
11.TV/AV 
selects TV or AV or Component mode. switches the set on from standby. exits the Teletext mode.
12.I/II/*
selects the language during dual language broadcast. selects the sound output (option).
13.Q.VIEW (or YELLOW)
returns to the previously viewed programme.
14.LIST (or BLUE)
displays the programme table.
* : No function
COLOURED BUTTONS : These buttons are used for teletext (only TELETEXT models) or programme edit.
Battery installation
The remote control handset is powered by two AAA type batteries. To load the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.
Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
4
Loading...