LG 19EN33V, 20EN33V, 22EN33V, 24EN33V, 24EN33VW Owner's Manual

www.lg.com

OWNER’S MANUAL

LED LCD MONITOR

19EN33V
20EN33V
22EN33V
24EN33V
24EN33VW

Please read this manual carefully before operating
your set and retain it for future reference.

LED LCD MONITOR MODEL

ENGLISH

2

ENG

ENGLISH

TABLE OF CONTENTS

CONTENTS

3 ASSEMBLING AND PREPAR-

ING

3 Unpacking

4 Parts and buttons

5 Setting up the Monitor set

5 - Attaching the Stand Base

5 - Detaching the Stand Base

6 - Mounting on a table

6 - Using the cable holder

8 - Mounting on a wall

9 USING THE MONITOR SET

9 Connecting to a PC

9 - D-SUB connection

9 - DVI-D connection

9 - HDMI connection

11 CUSTOMIZING SETTINGS

12 Customizing Settings

12 - Menu Settings

13 - Picture

14 - Color

15 - Display

15 - Volume

16 - Others

17 MY KEY Setting

18 FUNC. Setting

18 - Picture Mode

19 - SUPER ENERGY SAVING

20 - DUAL DISPLAY

20 - DUAL WEB

21 - MY KEY Setting

22 TROUBLESHOOTING

24 SPECIFICATIONS

24 19EN33V

25 20EN33V

26 22EN33V

27 24EN33V/24EN33VW

28 Preset Modes (Resolution)

29 HDMI TIMING

29 Indicator

30 PROPER POSTURE

30 Proper posture for using the Monitor set.

3

ENG

ENGLISH

ASSEMBLING AND PREPARING

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.

y

Do not use any unapproved accessories to ensure the safety and product life span.

y

Any damages or injuries by using unapproved accessories are not covered by the warranty.

y

The accessories supplied with your product may vary depending on the model.

y

Product specifications or contents in this manual may be changed without prior notice due to upgrade
of product functions.

CAUTION

NOTE

Stand Body

Stand Base

CD(Owner's Manual) /

Card

D-SUB Cable

DVI-D Cable

(This cable is not included

in all countries.)

( Depending on the country ) ( Depending on the country )

Power Cord AC-DC Adapter AC-DC Adapter

or

4

ENG

ENGLISH

ASSEMBLING AND PREPARING

Parts and buttons

Power Indicator

y

Lighting On: Turned on

y

Lighting Off: Turned off

Connection panel (See p.9)

Button (See p.11)

(Power Button)

5

ENG

ENGLISH

ASSEMBLING AND PREPARING

Attach the

Stand Body

to the monitor set.

Attach the

Stand Base

.

Tighten the screw to the right with a coin.

Setting up the Monitor set

Attaching the Stand Base

1

Place the Monitor set with the screen side

down on a flat and cushioned surface.

Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.

CAUTION

2

Stand Base

Stand Body

1

2

3

y

This illustration depicts the general model of
connection. Your monitor may differ from the
items shown in the picture.

y

Do not carry the product upside down holding
only the stand base. The product may fall
and get damaged or injure your foot.

CAUTION

Detaching the Stand Base

1

Place the Monitor set with the screen side

down on a flat and cushioned surface.

2

Stand Base

Stand Base

Stand Body

Stand Body

Pull out the

Stand Body

and

Stand Base

from the monitor set.
Turn the screw to the left with a coin.
Pull out the

Stand Base

.

1

2

3

6

ENG

ENGLISH

ASSEMBLING AND PREPARING

Mounting on a table

1

Lift and tilt the Monitor set into its upright

position on a table.

Leave a 10 cm (minimum) space from the wall
for proper ventilation.

Using the cable holder

2

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

3

Press (Power) button on the bottom switch

panel to turn the power on.

10 cm

10 cm

10 cm

10 cm

Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.

CAUTION

Cable holder

or

7

ENG

ENGLISH

ASSEMBLING AND PREPARING

Using the Kensington security system

The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit

http://www.kensington.com

.

Connect the Kensington security system cable
between the Monitor set and a table.

The Kensington security system is optional.
You can obtain it from most electronics stores.

NOTE

When you adjust the angle, do not hold the
bottom of the Monitor set frame as shown on
the following illustration, as may injure your
fingers.

Do not touch or press the screen when
adjusting the angle of the monitor.

Do not hold this set like below picture.Monitor
screen can detach from stand base and injure
your body.

WARNING

Tilt from +20 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.

NOTE

Front Rear

8

ENG

ENGLISH

ASSEMBLING AND PREPARING

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.

If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.

1

Please, Use the screw and wall mount interface

in accordance with VESA Standards.

2

If you use screw longer than standard, the

monitor might be damaged internally.

3

If you use improper screw, the product might be

damaged and drop from mounted position. In
this case, LG Electronics is not responsible for
it.

4

VESA compatible.

5

Please use VESA standard as below.

y

784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

y

787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad

and screws.

10 cm

10 cm

10 cm

10 cm

y

Disconnect the power cord first, and then
move or install the Monitor set. Otherwise
electric shock may occur.

y

If you install the Monitor set on a ceiling or
slanted wall, it may fall and result in severe
injury.

y

Use only an authorized LG wall mount
and contact the local dealer or qualified
personnel.

y

Do not over tighten the screws as this may
cause damage to the Monitor set and void
your warranty.

y

Use only screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.

y

Use the screws that are listed on the VESA
standard screw specifications.

y

The wall mount kit will include an installation
manual and necessary parts.

y

The wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.

y

The length of screws may differ depending
on the wall mount. Be sure to use the proper
length.

y

For more information, refer to the
instructions supplied with the wall mount.

CAUTION

NOTE

Model

19EN33V
20EN33V
22EN33V

24EN33V

24EN33VW

VESA (A x B)

75 x 75 100 x 100

Standard
screw

M4

Number of
screws

4

9

ENG

ENGLISH

USING THE MONITOR SET

USING THE MONITOR SET

Connecting to a PC

y

Your Monitor set supports Plug & Play*.
*Plug & Play: A PC recognizes a connected

device that users connect to a PC and turn
on, without device configuration or user
intervention.

D-SUB connection

Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.

y

Mac adapter

For Apple Macintosh use, a separate plug
adapter is needed to change the 15 pin
high density (3 row) D-SUB VGA connector
on the supplied cable to a 15 pin 2 row
connector.

y

When using a D-Sub signal input cable
connector for Macintosh

y

If you use HDMI PC, it can cause compatibility
problem.

NOTE

NOTE

DVI-D connection

Transmits a digital video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with a DVI cable as shown in the following
illustrations.

HDMI connection

Transmits the digital video and audio signals from
your PC or A/V to the Monitor set. Connect the PC
or A/V and the Monitor set with the HDMI cable as
shown in the following illustrations.

10

ENG

ENGLISH

USING THE MONITOR SET

y

When you want to use two PC in our Monitor,
please connect the signal cable(D-SUB/
DVI-D) respectively in Monitor set.

y

If you turn the Monitor set on while it is cold,
the screen may flicker. This is normal.

y

Some red, green, or blue spots may appear
on the screen. This is normal.

y

"Self Image Setting" Function.

This function provides the user with optimal
display settings.When the user connects
the monitor for the first time, this function
automatically adjusts the display to optimal
settings for individual input signals.(Only
supported in Analog Mode)

y

‘AUTO’ Function.

When you encounter problems such as
blurry screen, blurred letters, screen flicker
or tilted screen while using the device or
after changing screen resolution, press the
AUTO function button to improve resolution.
(Only supported in Analog Mode)

NOTE NOTE

y

Connect the signal
input cable and tighten
it by turning the screws
clockwise.

y

Do not press the screen with your finger for
a long time as this may result in temporary
distortion on the screen.

y

Avoid displaying a fixed image on the
screen for a long period of time to prevent
image burn. Use a screensaver if possible.

CAUTION

Self Image Setting Function

Press the power button on the bottom panel to
turn the power on. When monitor power is turned
on, the "

Self Image Setting

" Function is executed

automatically. (Only supported in Analog Mode)