LG 14SR1RB User guide
Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number :
Serial number :
P/NO : MFL42377935-EN (MC059D)
BZ03
2
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and mains plugs.
Press the POWER button on the front panel or side panel
to turn off the TV when the TV set is not being used for a
long time.It is recommended to remove the plug from the
wall outlet(Power point).
Disconnecting device from mains
Mains plug is the disconnecting device. The plug
must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the
set to rain or moisture.
Do not place anything containing liquid on top of
the set, this may cause a fire or could give an
electric shock.
Service
Never remove the back cover of the set as this
can expose you to very high voltage and other
hazards. If the set does not operate properly,
unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.
Location
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.
Installation
Connection of external equipment
Aerial socket
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4. Select the programme number where the
VCR channel is stored.
5. Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the
VCR to audio/video in sockets of the set and
in sockets of the VCR to out sockets of the
set.
2. If the VCR is connected to the AV sockets on
the set, press the TV/AV button to select
AV
(or AV 1 )
.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
Location and function of controls
3
Remote control handset
1. POWER
switches the set on from standby or off to
standby.
2. MENU
selects a menu.
3. MUTE
switches the sound on or off.
4. NUMBER BUTTONS (option)
switches the set on from standby or directly
select a number.
5. Q.VIEW
returns to the previously viewed programme.
6.
DD / EE
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
scans programmes automatically.
FF / GG
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
VV
accepts your selection or displays the current
mode.
7. TV/AV
selects TV or AV mode.
switches the set on from standby.
COLOURED BUTTONS : These buttons are used
for programme edit.
Battery installation
The remote control handset is powered by AAA
type batteries. To load the batteries, turn the
remote control handset over and open the battery
compartment. Install batteries as indicated by the
polarity symbols ( and ) marked inside the
compartment.
Note : To avoid damage from possible battery
leakage, remove the batteries if you do not plan to
use the remote control handset for an extended
period of time .
Front panel
1. MAIN POWER (ON/OFF)
switches the set on or off.
2. REMOTE CONTROL SENSOR
Note : Only use the supplied remote control
handset. (When you use others, they’ll be
not able to function.)
3. POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby
mode.
dims when the set is switched on.
4. MENU
selects a menu.
5. OK
accepts your selection or displays the current
mode.
6. < VOL > (Volume Up/Down)
turns right or left about 10 degree to increase
or decrease volume level.
adjusts menu settings.
7. < PR > (Programme Up/Down)
turns right or left about 10 degree to select a
programme or a menu item.
switches the set on from standby.
Note:Do not apply force to the VOL and PR button.
It can be only adjusted to 10 degree to the right or
left.So you can adjust the program and volume by
swivelling it again and again.
7
5
4
6
1
3
2
+
-
3
4
5
6
1
7
2
Loading...