LG 14SA3RB, 14SB1RB User guide

Colour Television

OWNER’S MANUAL

BZ03

Please read this manual carefully before operating your set. Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the back cover and quote this information to your dealer when you require service.

Model number	:
Serial number	:

P/NO : MFL61959405-EN (CW91B)

Installation

Power

This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.

Press the POWER button on the front panel or side panel to turn off the TV when the TV set is not being used for a long time.It is recommended to remove the plug from the wall outlet(Power point).

Disconnecting device from mains

Mains plug is the disconnecting device. The plug must remain readily operable

Warning

To prevent fire or shock hazard, do not expose the set to rain or moisture.

Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.

Service

Never remove the back cover of the set as this can

expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.

Aerial

Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.

Location

Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.

Note:

To remove dirt or fingerprint on the surface of your TV, please rub with a line-free cloth supplied in the accessory.Do not pose too much pressure in cleaning so as to prevent any risk of damage to the product.(option)

Connection of external equipment

Aerial socket

1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.

2.Connect the aerial cable to the RF aerial in socket of the VCR.

3.Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.

4.Select the programme number where the

VCR channel is stored.

5.Press the PLAY button on the VCR.

Audio/Video in/out sockets (option)

1.Connect the audio/video out sockets of the

VCR to audio/video in sockets of the set and

in sockets of the VCR to out sockets of the set.

2.If the VCR is connected to the AV sockets on the set, press the TV/AV button to select AV .

3.Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

ANTENNA

IN

IN

VIDEO AUDIO

VCR

Location and function of controls

Battery installation

The remote control handset is powered by AAA

type batteries.Install batteries as indicated by the

polarity symbols ( + and - ) marked inside the

compartment.

or

Note : To avoid damage from possible battery

leakage, remove the batteries if you do not plan to

use the remote control handset for an extended

period of time

2

Location and function of controls
Remote control handset			scans programmes automatically.
Before you use the remote control handset,			F / G (Volume Up/Down)
			adjusts the volume.
please install the batteries.			adjusts menu settings.
1			OK
			accepts your selection or displays the current
7	10
			mode.
		5.	SLEEP
			sets the sleep timer.
2		6.	EYE/* (option)
			switches the eye function on or off.
		7.	MUTE
3	8		switches the sound on or off.
		8.	TV/AV
			selects TV or AV mode.
4			switches the set on from standby.
			exits the Teletext mode.
		9.	I/II/*
			selects the language during dual language
5	6		broadcast.
			selects the sound output (option).
	9
		10.	Q.VIEW (or YELLOW)
1
			returns to the previously viewed programme.
7	8
	10	Front panel
			MAIN POWER (ON/OFF)
2			switches the set on or off.
			POWER/STANDBY INDICATOR
			illuminates brightly when the set is in standby
3			mode.dims when the set is switched on.
			REMOTE CONTROL SENSOR
			Note : Only use the supplied remote control
4			handset. (When you use others, they will not
			be able to function.)
			MENU
5	6		selects a menu.
			A/OK
	9		accepts your selection or displays the current
			mode.

1.POWER

switches the set on from standby or off to standby.

2.NUMBER BUTTONS

Switches the set on from standby or directly select a number.

3.MENU

selects a menu.

4.D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.

F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.

D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.

Note :

What is shown here may be somewhat different from your set or can not be supplied on your area.

3