LG 14F9CB Owner’s Manual
Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number :
Serial number :
Contents
2
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of
thunderstorms or powercuts, please pull out the
aerial and mains plugs.
Warning
To prevent fire or shock hazard, do not expose the
set to rain or moisture.
Do not place anything containing liquid on top of
the set, this may cause a fire or could give an
electric shock.
Service
Never remove the back cover of the set as this
can expose you to very high voltage and other
hazards. If the set does not operate properly,
unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back
cover. For the best reception an outdoor aerial
should be used.
Location
Position your set so that no bright light or sunlight
falls directly onto the screen. Care should be
taken not to expose the set to any unnecessary
vibration, moisture, dust or heat. Also ensure that
the set is placed in a position to allow a free flow
of air. Do not cover the ventilation openings on the
back cover.
Installation
Installation.........................................................2
Connection of external equipment..................2
Location and function of controls...................3
Basic operation.................................................5
On screen menus..............................................5
Setting up TV stations......................................6
Picture adjustment............................................9
Sound adjustment...........................................10
Time setting.....................................................11
Other functions...............................................12
Troubleshooting check list............................13
Connection of external equipment
Aerial socket
1. Connect the RF out socket of the VCR to the
aerial socket on the back of the set.
2. Connect the aerial cable to the RF aerial in
socket of the VCR.
3. Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4. Select the programme number where the
VCR channel is stored.
5. Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1. Connect the audio/video out sockets of the
VCR to audio/video in sockets of the set and
in sockets of the VCR to out sockets of the
set.
2. If the VCR is connected to the AV sockets on
the set, press the TV/AV button to select
AV
(or AV 1 )
.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the
screen.
ANT IN
VCR
IN
OUT
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
1. POWER
switches the set on from standby or off to standby.
2. NUMBER BUTTONS
switches the set on from standby or directly select a number.
3. MENU
selects a menu.
4. EYE/*(option)
switches the eye function on or off.
5.
/
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
scans programmes automatically.
FF / GG
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current mode.
6. Q.VIEW
returns to the previously viewed programme.
7. SSM/*(Sound Status Memory) (option)
recalls your preferred sound setting.
8. PSM (Picture Status Memory)
recalls your preferred picture setting.
9. TURBO PICTURE / SOUND BUTTON (option)
selects Turbo picture and sound.
10. MUTE
switches the sound on or off.
11. TV/AV
selects TV or AV mode.
switches the set on from standby.
12. I/II/*(option)
selects the language during dual language broadcast.
selects the sound output.
13. LIST
displays the programme table.
14. SLEEP
sets the sleep timer.
15. FAVOURITE
selects a favorite programme.
16. SURROUND (ºº/*) (option)
selects surround sound.
Battery installation
The remote control handset is powered by two AAA type batteries. To load the batteries, turn the remote control handset over
and open the battery compartment. Install two batteries as indicated by the polarity symbols ( and ) marked inside the compartment.
Location and function of controls
3
( )
( )
+
-
Q.VIEW
LIST
PSM
SSM/
I II
SLEEP
SOUNDPICTURE
TURBO/
/
FAVOURITE
EYE
/
/
/
1
2
3
4
5
6
8
9
7
10
11
12
14
13
15
16
1. MAIN POWER (ON/OFF)
switches the set on or off.
2. POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby mode.
dims when the set is switched on.
3. REMOTE CONTROL SENSOR
Note : Only use the supplied remote control handset.
(When you use others, they’ll be not able to function.)
4. MENU
selects a menu.
5. OK
accepts your selection or displays the current mode.
FF / GG
(Volume Up/Down) (option)
adjusts the volume.
adjusts menu settings.
DD / EE
(Programme Up/Down) (option)
selects a programme or a menu item.
switches the set on from standby.
Note : Shown is a simplified representation of front or side panel. Here shown may be
somewhat different from your set.
Location and function of controls
4
ON/OFF
MENU OK
VOL
PR
1
2
4
3
5
Front panel
14F9 series
Basic operation
On and off
1. Press the main power button to switch the set
on.
2. If the set is in standby mode, press the
POWER,
DD / EE
, TV/AV or NUMBER buttons
on the remote control handset to switch it on
fully.
3. Press the POWER button on the remote con-
trol handset.
The set reverts to standby mode.
4. Press the main power button again to switch
the set off.
Note : If, while the set is switched on, the mains
plug is disconnected the set will switch to standby
or power on when the mains plug is replaced in
the mains power socket.
Programme selection
You can select a programme number with the
DD
/
EE
or NUMBER buttons.
Volume adjustment
Press the
FF / GG
button to adjust the volume.
Quick view
Press the Q.VIEW button to view the previous programme you were watching.
Mute function
Press the MUTE button. The sound is switched off
and the display >appears.
You can cancel it by pressing the MUTE,
FF / GG
,
SSM/*, I/II/*, TURBO SOUND button.
On screen language selection (option)
The menu can be displayed on the screen in
desired language. First select your language.
1. Press the MENU button and then
DD / EE
but-
ton to select the Special menu.
2. Press the GGbutton to select Language.
3. Press the GGbutton and then
DD / EE
button to
select your desired language.
All the on screen displays will appear in the
selected language.
Press the OK or
FF
button to select the Special
menu.
4. Repeatedly press the MENU button to return
to normal TV viewing.
5
On screen menus
The dialogue between you and your set takes
place on screen with an operator menu. The buttons required for the operating steps are also displayed.
Menu selection
1. Press the MENU button and then
DD / EE
button to
display each menu.
2. Press the GGbutton and then
DD / EE
button to
select a menu item.
3. Press the GGbutton to display the sub menu or
the pull-down menu.
4. Change the setting of an item in the sub or
pull-down menu with
FF / GG
or
DD / EE
.
You can move to the higher level menu with
OK or FFbutton and to move to the lower level
menu press the GGbutton.
Note :
a. In mono models, the Sound menu does not
appear.
b. In some models,
Turbo Pic. will not display in
the Picture menu.
c. In some models, Turbo.Snd., AV L , Balance,
Woofer, X-WAVE or Treble, Bass will not dis-
play in the Sound menu.
d. In some models, Language, Blue back,
Game, Booster will not display in the Special
menu.