LG 141K TX, 3828VA0565M, MF056B User Manual

PLASMA TV

OWNER’S MANUAL

Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.

Model number : Serial number :

P/NO : 3828VA0565M (MF056B, 141K TX)

2 PLASMA TV

Safety Warnings

Safety Instructions

Do not place the set in direct sunlight or near heat sources such as heat registers, stove and so on.

- This may cause a fire.

Do not use the set in damp place such as a bathroom or any place where it is likely to get wet.

- This may cause a fire or could give an electric shock.

Bend antenna cable between inside and outside building to prevent rain from flowing in.

- This may cause water damaged inside the set and could give an electric shock.

Earth wire should be connected.

- If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage.

- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.

- Do not connect ground to telephone wires, lightning rods or gas pipe.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

- This may cause a fire or could give an electric shock.

Do not insert any object into the exhaust vent.

- This may cause a fire or could give an electric shock.

Do not place heavy objects on the set.

- This may cause serious injury to a child or adult.

Do not use water while cleaning the set.

- This may cause damaged the set or could give an electric shock.

In case of smoke or strange smell from the set, switch it off ,unplug it from the wall outlet and contact your dealer or service centre.

- This may cause a fire or could give an electric shock.

Do not attempt to service the set yourself. Contact your dealer or service centre.

- This may cause damaged the set or could give an electric shock.

During storm activity, unplug the set from the wall outlet and don’t touch the antenna cable.

- This may cause damaged the set or could give an electric shock.

DISCONNECTING DEVICE FROM MAINS

- Mains plug is the disconnecting device. The plug must remain readily operable.

WARNING

Short-circuit

breaker

Power

supplier

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Owner’s Manual 3

ENGLISH

Safety Warnings

Never touch the power plug with a wet hand.

- This may cause an electric shock.

Disconnect from the mains and remove all connections before moving.

Do not place the set in a built-in installation such as a bookcase or rack.

- Ventilation required.

When installing the set on a table, be careful not to place the edge of its stand on the end of the table.

- This may cause the set to fall, causing serious injury to a child or adult, and serious damage to the set.

Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.

- This may cause an electric shock.

There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.

- This may cause an electric shock.

Do not pull the plug not the cord when disconnecting.

- This may cause a fire.

Ensure the power cord doesn’t trail across any hot objects like a heater.

- This may cause a fire or an electric shock.

Do not plug in unit if power cord or plug is damaged or the connecting part of the power outlet is loose.

- This may cause a fire or an electric shock.

Dispose of used batteries carefully to prevent a child from eating them.

- In case of a child eating them, contact doctor immediately.

When moving the set assembled with speakers do not carry holding the speakers.

- This may cause the set to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

- This may cause damage the set or could give an electric shock.

Contact the service centre once a year to clean the internal part of the set.

- Accumulated dust can cause mechanical failure.

The distance between eyes and the screen should be approx. 5 ~ 7 times the diagonal length of the screen away.

- If not, eyes will strain.

Unplug the set from the wall outlet when it is left unattended and unused for long periods of time or in the occurrance of a state of emergency.

- Accumulated dust may cause a fire or an electric shock from deterioration through electric leakage.

NOTES

Safety instructions have two kinds of information, and each meaning of it is as below.

Take care of danger that may happen under specific condition.

The violation of this instruction may cause serious injuries and even death. The violation of this instruction may cause light injuries or damage of the

product.

WARNING

NOTES

4 PLASMA TV

Contents

After reading this manual, keep it in a place where the user can refer to easily.

Safety Warnings

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .2~3

Introduction

Remote Control Key Functions . . . . . . . . . . . . . . . .5

Location and Function of Controls . . . . . . . . . . . 6~7

Installation

External Equipment Viewing Setups . . . . . . . . . . . .8

Displayable Monitor Specification . . . . . . . . . . . . . .9

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installation Options . . . . . . . . . . . . . . . . . . . . . . .12

Operation

Turning on the Set . . . . . . . . . . . . . . . . . . . . . . . .13

On-Screen Menu Language Selection (option) . . .13

On screen menus . . . . . . . . . . . . . . . . . . . . . . . .14

Channel Menu Options

Auto Programme Tuning . . . . . . . . . . . . . . . . . . .15

Manual Programme Tuning . . . . . . . . . . . . . . . . .15

Fine Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Assigning a Station Name . . . . . . . . . . . . . . . . . .16

Booster (option) . . . . . . . . . . . . . . . . . . . . . . . . . .16

Programme Edit . . . . . . . . . . . . . . . . . . . . . . . . . .16

Favourite Programme . . . . . . . . . . . . . . . . . . . . .16

Calling up the Programme Table . . . . . . . . . . . . .16

Picture Menu Options

PSM (Picture Status Memory) . . . . . . . . . . . . . . .17

CSM (Colour Status Memory) . . . . . . . . . . . . . . .17

Manual Colour Temperature Control . . . . . . . . . .17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

ACM (Active Colour Management) . . . . . . . . . . . .17

Manual Picture Control . . . . . . . . . . . . . . . . . . . .17

Sound Menu Options

SSM (Sound Status Memory) . . . . . . . . . . . . . . . .17

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

AVL(Auto Volume Leveler) . . . . . . . . . . . . . . . . .17

Adjusting Sound Control . . . . . . . . . . . . . . . . . . .17

TV speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Stereo/Dual Reception . . . . . . . . . . . . . . . . . . . . .18

NICAM Reception (option) . . . . . . . . . . . . . . . . . .18

Time Menu Options

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .18

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . .18

Auto Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Special Menu Options

Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ISM (Image Sticking Minimization) Method . . . . . .19

Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Screen Menu Options

Auto Configure . . . . . . . . . . . . . . . . . . . . . . . . . .19

Manual Configure . . . . . . . . . . . . . . . . . . . . . . . .19

Selecting Wide VGA/XGA mode . . . . . . . . . . . . . 19

Setting Picture Format . . . . . . . . . . . . . . . . . . . . .20

Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . . . .20

Screen Position . . . . . . . . . . . . . . . . . . . . . . . . . .20

Cinema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

NR (Noise Reduction) . . . . . . . . . . . . . . . . . . . . .20

Initializing (Reset to original factory value) . . . . . .20

Teletext (option)

Teletext Language Selection

. . . . . . . . . . . . . . . .20

Switch on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

SIMPLE Text (option) . . . . . . . . . . . . . . . . . . . . . .21

TOP Text (option) . . . . . . . . . . . . . . . . . . . . . . . . .21

FASTEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Special Teletext Functions . . . . . . . . . . . . . . . . . .21

PIP (Picture-in-Picture) Feature

Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Programme Selection for Sub Picture . . . . . . . . . .22

Selecting an Input Signal Source for the PIP . . . .22

Moving the PIP (PIP mode only) . . . . . . . . . . . . .22

POP (Picture-out-of-Picture: Channel Scan) . . . . .22

Picture Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Adjusting the screen for the PIP . . . . . . . . . . . . . .22

Adjusting PIP Transparency (PIP mode only) . . . .22

Notes on Memory Card . . . . . . . . . . . . . . . . .23~25

JPEG File Viewing Options . . . . . . . . . . . . . .26~30

MP3 File Playing Operation . . . . . . . . . . . . . .31~34

Miscellaneous

Programming the Remote (option) . . . . . . . . . . . .35

Programming Codes (option) . . . . . . . . . . . . .36~37

Troubleshooting Checklist . . . . . . . . . . . . . . . . . .38

Product Specifications . . . . . . . . . . . . . . . . . . . . .39

Contents

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

Owner’s Manual 5

Introduction

ENGLISH

Remote Control Key Functions

- When using the remote control aim it at the remote control sensor of the set.

- There maybe a defect in consecutive operation of remote control in a specified brightness according to this set.

• Open the battery compartment cover on the back side and insert the batteries with correct polarity.

• Install two 1.5V alkaline batteries of AA type. Don’t mix used batteries with new batteries.

Installing Batteries

MODE

INPUT

DVD

VCR

AUDIO

PIP PR -

PIP PR +

SWAP

PIP INPUT

STB

MUTE

SIZE POSITION INDEX

HOLD

TIME REVEAL MIX

MODE

SLEEP I/II

PIP

M/C EJECT

PSM SSM ARC

TEXT

Q.VIEWLIST

FAV

VOL PR

MULTIMEDIA

POWER

CABLE

EXIT

INFO i

MARK

MULTIMEDIA

Selects the Component, RGB or HDMI modes. switches the set on from standby.

POWER

switches the set on from standby or off to standby.

MARK

Selects the wanted functions.

Brings up the menu to select the Photo or Music mode of Xstudio for memory cards.

EXIT

Clears all on-screen displays and returns to TV viewing from any menu.

Q.VIEW

Returns to the previously viewed programme.

M/C EJECT

Remove the Memory Card.

ARC

Changes the picture format.

FAV

selects a favourite programme.

TEXT

These buttons are used for teletext. For further details, see the ‘Teletext’ section.

Note : In teletext mode, the PIP PR +/-, SWAP and PIP INPUT buttons are used

for teletext function.

PIP

Switches the sub picture on or off. Selects PIP, POP or DW modes.

PIP PR + /-

Selects a programme for the sub picture.

SWAP

Alternates between main and sub picture.

PIP INPUT

Selects the input mode for the sub picture.

SIZE

Adjusts the sub picture size.

POSITION

Moves the sub picture to

DD/ EE

or FF/

direction.

INPUT

Selects the TV, AV1, AV2, S-Video, AV3, AV4,

AV5, Component, RGB or HDMI modes.

switches the set on from standby.

MODE

Selects another device.

VCR BUTTONS

Controls a video cassette recorder.

These buttons are used for X-Studio.

For further details, see the ‘X-Studio’ section.

Displays on screen menus one by one.

Exits the current menu.

Memorizes menu changes.

INFO

Displays information on top of the screen

whilst watching the TV.

MUTE

Switches the sound on or off.

NUMBER buttons

LIST

Displays the programme table.

PSM

Adjusts the factory preset picture according

to the room.

SSM

To select the sound appropriate to your

viewing programme.

SLEEP

Sets the sleep timer.

I/II

Selects the language during dual language

broadcast.

Selects the sound output.

VOL

DD / EE

(Volume Up/Down)

Increases/decreases sound level.

DD / EE

(Programme Up/Down)

Selects a programme.

accepts your selection or displays the

current mode.

DD/ EE

or FF/

Adjusts menu settings.

Selects menu item.

6 PLASMA TV

Introduction

Location and Function of Controls

1. Remote Control Sensor

2. Power Button

Switches the set on from standby or off to standby.

3. INPUT Button

Selects the TV, AV1, AV2, S-Video, AV3, AV4, AV5, Component, RGB or HDMI modes.switches the set on from standby.

4. MENU

Displays on screen menus one by one. Exits the current menu. Memorizes menu changes.

5. OK

Accepts your selection or displays the current mode.

6.DD/ EE(Programme Up/Down)

Selects a programme or a menu item. Switches the set on from standby.

FF/ GG

(Volume Up/Down)

Adjusts the volume. Adjusts menu settings.

7. INDEX

Switches FRONT Display on or off.

8. Power Indicator

Illuminates red in standby mode, illuminates green when the set is turned on.

9. Intelligent Eye

Adjusts picture according to the surrounding conditions.

10. Memory Card Slots 1, 2

- Shown is a simplified representation of the set.

- Here shown may be somewhat different from your set.

VOL

MENUINPUT OK

2 3 4 5 6

Owner’s Manual 7

Introduction

ENGLISH

Location and Function of Controls

S-VIDEO

AAV5V5

AC INPUT

Antenna

AUDIO AUDIO

L R

VIDEO VIDEO

COMPONENTCOMPONENT

AUDIO AUDIO

V VARIABLE ARIAB LE AUDIO OUTAUDIO OUT

AUDIO AUDIO

(MONO)(MONO)

L R

S-VIDEOS-VIDEO VID EOVIDEO

AAV4V4

AAV1V 1

AAV2V 2

AAV3V 3

HDMI/ DVI(VIDEO)

AUDIO INPUT

RGB INPUT

RS-232C INPUT

(CONTROL/SERVICE)

REMOTE CONTROL

VIDEOAUDIOR

L/MONO

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT

Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket.

Note:

If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Filter core along with separate cable.

2. REMOTE CONTROL

3. RS-232C INPUT(CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

4. COMPONENT INPUT

Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of AUDIO INPUT.

AUDIO/VIDEO IN SOCKETS (AV4)

Connect the audio/video out sockets of external equipment to these sockets.

S-VIDEO/AUDIO IN SOCKETS

Connect the S-VIDEO out socket of an VCR to the S-VIDEO socket. Connect the audio out sockets of the VCR to the audio sockets as in AV4.

5. VARIABLE AUDIO OUTPUT

6. EURO SCART SOCKET

Connect the euro scart socket of the VCR to these sockets.

Note:

a. If you want to use the EURO scart cable, you have to use the signal shielded Euro scart cable. b. If the S-VIDEO(Y/C) signal is received through the Euro scart socket 2 (AV 2), you must change to the S-Video 2 (Y/C) mode.

7. ANTENNA INPUT

8. POWER CORD SOCKET

This Monitor operates on AC power. The voltage is indicated on the Specifications page. Never attempt to operate the set on DC power.

9. AUDIO/VIDEO INPUT (AV5) S-VIDEO/AUDIO IN SOCKETS

42 3 6 75 8

8 PLASMA TV

Installation

External Equipment V

iewing Setups

AV1AV1

Antenna

AUDIO A UDIO

L R

VIDEO VIDEO

COMPONENTCOMPONENT

AUDIO A UDIO

V VARIA BLE ARIAB LE AUDIO OUTAUDIO OU T

AUDIO A UDIO

(MONO)(MONO)

L R

S-VIDE OS-VIDE O VIDE OVIDEO

AAV4V4

AAV1V1

AAV2V2

AAV3V3

HDMI/ DVI(VIDEO)

AUDIO INPUT

RGB INPUT

RS-232C INPUT

(CONTROL/SERVICE)

REMOTE CONTROL

Connection to PC

Connection to AV equipment

Owner’s Manual 9

Installation

ENGLISH

Displayable Monitor Specification

RGB / HDMI mode

Resolution

640x350

720x400

640x480

848x480

800x600

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

852x480

832x624

1024x768

1360x768

1366x768

1152x864

1152x870

1280x960

1280x768

1280x1024

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

85.00

60.00

75.02

60.00

75.02

60.05

70.01

75.00

75.06

60.00

75.00

60.02

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

37.799

39.375

31.500

37.799

39.375

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.677

47.700

59.625

47.700

59.625

54.348

63.995

67.500

68.681

47.693

60.091

60.023

63.981

Resolution

640x350

720x400

640x480

848x480

800x600

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

852x480

832x624

1024x768

1360x768

1366x768

1152x864

1152x870

1280x960

1280x768

1280x1024

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

85.00

60.00

75.02

60.00

75.02

60.05

70.01

75.00

75.06

60.00

75.00

60.02

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

37.799

39.375

31.500

37.799

39.375

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.677

47.700

59.625

47.700

59.625

54.348

63.995

67.500

68.681

47.693

60.091

60.023

63.981

42PX4R / 42PX5R Series 50PX4R / 50PX5R Series

10 PLASMA TV

Installation

- HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.

- This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).

- This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.

- When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets the HDMI/DVI source devices automatically. After reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data (EDID) stored in the set is used. If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.

- When Source Devices have DVI Output Connector, you must connect audio with separated cable. (Refer to <How to connect>)

How to connect

1. When Source Devices (DVD Player or Set Top Box) support HDMI.

- If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the product).

- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution manually.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

- Because HDMI sends Digital Video and Audio with one cable, there is no need for a special Audio Cable when using a HDMI Cable.

2. When Source Devices (DVD Player or Set Top Box) supports DVI.

- If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).

- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in : 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution manually.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

- In this case, use another cable for audio. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.

3. When PC supports DVI.

- If PC have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).

- To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.

- Use the the set’s HDMI/DVI (VIDEO) for video connections, depending on your PC connector.

- If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or HDMI/DVI Input to display the PC on the set.

- If he graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input; (the other mode is set to Plug and Play automatically by the set.)

- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

- In this case, use another cable for audio. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.

Reference

Cable sample (not supplied with the product)

How to use

1. Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set.

2. Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.

3. Select HDMI/DVI Input source in Main Input option of PIP/DW menu.

4. Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.

- Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.

- When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit to Screen. As shown on page 29, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service centre.

- When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA-861B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service centre.

- In case HDMI/DVI Source Devices Cable is not connected or poor cable connection, "No Signal" OSD display will appear. And in case of Video Resolution not being supported by the set output in HDMI/DVI Source Devices, "No Signal" OSD display will appear. Refer to the Manual of HDMI/DVI Source Devices or contact your service centre.

HDMI to DVI Cable

Analog Audio Cable

(RCA type)

Analog Audio Cable

(Stereo to RCA type)

HDMI Cable

Owner’s Manual 11

Installation

ENGLISH

AS mark

LG TV

Owner’s Manual

1.5V

Alkaline batteries

Power Cord

MODE

TV/AV

DVD

VCR

PIP

ZOOM-

ZOOM+

MUTE

TEXT/

SLEEP

LIST

I/II

AUDIO

PIPPR-

PIPPR+

SWAP

PIPINPUT

STB

ARC

SSM

FAVOURITE

SIZE POSITION INDEX

HOLD

TIME REVEAL MIX

MODE

Q.VIEW

PSM

VOL PR

MULTIMEDIA

POWER

CABLE

EXIT

Remote Control handset

- Optional extras can be changed or modified for quality improvement. Without any notification, new optional extras can be added.

- Contract your dealer for the purchasing of these items.

Optional Extras

Accessories

Tilt wall mounting bracket

Video cables Audio cables

Ceiling mounting bracket

- Secure the set assembly by joining it to a wall by using the Eye Bolts/Wall brackets.

Joining the set assembly to the wall to prevent the set tumbling

• If the set is to be mounted on a desk top, insert the 2 Eye-Bolts and tighten them securely in the upper holes as shown. Install the wall brackets on the wall with 2 bolts*, (not supplied with the product), as shown. Match the height of the Eye-Bolts and the wall brackets. Check to be sure the Eye-Bolts and the brackets are tightened securely.

• Secure the set assembly to the wall with strong strings or wound wire cables,

(not supplied with the product), as shown.

2-Wall brackets

2-Eye Bolts

12 PLASMA TV

Installation

Installation Options

• The set can be installed in different ways such as on a wall, or on a desktop etc.

• Install this set only in a location where adequate ventilation is available.

Desktop Pedestal Installation

• The set can be mounted on a desk as shown above.

Wall Mount: Horizontal Installation

• The set can be installed on a wall as shown above. (For further information, refer to the optional ‘Wall Mounting Bracket Installation and Setup Guide’.)

Swivel function (option)

• After installing the set, you can adjust the set manually to the left or right direction by 20 degrees to suit your viewing position.

Note : Before adjusting the angle, you must loosen (to the left) the shaft bolt on the middle of stand’s back. And when the stand is level with set, you must close (to the right) the shaft bolt to set the hole.

To Mount on a Wall

Wall mount minimum allowable clearances for adequate ventilation.

To Install on a Desktop

Pedestal mount minimum allowable clearances for adequate ventilation.

10cm

3cm

10cm

+ 28 hidden pages