Lexmark X656 MFP, X654 MFP, X651 MFP, X658 MFP, X652 MFP User Manual

5 (1)

T650n/dn/dtn, T652n/dn/dtn,

T654n/dn/dtn, X651 MFP,

X652 MFP, X654 MFP, X656 MFP,

X658 MFP

Technical Reference

May 2009

www.lexmark.com

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners.

© 2009 Lexmark International, Inc. All rights reserved.

740 West New Circle Road

Lexington, Kentucky 40550

Edition notice

May 2009

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.

For Lexmark technical support, visit support.lexmark.com.

For information on supplies and downloads, visit www.lexmark.com.

If you don't have access to the Internet, you can contact Lexmark by mail: Lexmark International, Inc.

Bldg 004-2/CSC

740 New Circle Road NW Lexington, KY 40550 USA

© 2009 Lexmark International, Inc. All rights reserved.

Trademarks

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. StapleSmart is a trademark of Lexmark International, Inc.

PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands. All other trademarks are the property of their respective owners.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.

Contents

 

Edition notice......................................................................................

2

Introduction........................................................................................

5

Understanding letters after model numbers...............................................................................................................

5

Learning about the printer...............................................................

7

Finding information about the printer...........................................................................................................................

7

Printer Control Language (PCL) page formatting........................

8

Printable areas.........................................................................................................................................................................

8

Supported paper and envelope dimensions...............................................................................................................

9

Printer Job Language (PJL).............................................................

11

PJL commands information.............................................................................................................................................

11

PostScript (PS) emulation...............................................................

12

Paper sizes supported........................................................................................................................................................

12

PostScript paper tray support.........................................................................................................................................

13

PostScript envelope size support..................................................................................................................................

14

PostScript envelope tray support..................................................................................................................................

16

Printer specifications......................................................................

18

Airflow requirement...........................................................................................................................................................

18

Noise emission levels.........................................................................................................................................................

18

Electrical specifications.....................................................................................................................................................

19

Power requirements...........................................................................................................................................................

19

Physical specifications.......................................................................................................................................................

20

Clearance requirements....................................................................................................................................................

22

Environmental conditions................................................................................................................................................

23

Altitude specifications and atmospheric pressure..................................................................................................

23

Appendix A: PCL support.................................................................

24

PCL emulation commands...............................................................................................................................................

24

GL/2 commands...................................................................................................................................................................

30

Contents

3

Appendix B: PJL support.................................................................

34

Common variables for both printer languages........................................................................................................

34

Printer-unique PJL variables for both printer languages......................................................................................

37

Common variables for PCL emulation.........................................................................................................................

46

Printer-unique variables for PCL emulation...............................................................................................................

47

Common variables for PostScript emulation............................................................................................................

47

Printer-unique variables for PostScript emulation..................................................................................................

48

Printer-unique LRESOURCE variables...........................................................................................................................

48

Status Readback commands...........................................................................................................................................

49

USTATUS unsolicited status variables..........................................................................................................................

49

PJL messages for auto-continuable conditions........................................................................................................

50

PJL messages for attendance conditions....................................................................................................................

56

PJL messages for paper handling..................................................................................................................................

64

PJL messages for paper jams...........................................................................................................................................

67

Service errors.........................................................................................................................................................................

74

Device attendance messages..........................................................................................................................................

74

Lexmark-unique PJL commands....................................................................................................................................

74

File and device protection commands........................................................................................................................

75

Appendix C: PostScript support.....................................................

77

Supplemental operators...................................................................................................................................................

77

Page device parameters....................................................................................................................................................

81

User interpreter parameters............................................................................................................................................

85

System interpreter parameters.......................................................................................................................................

86

Devices supported..............................................................................................................................................................

89

Device parameters..............................................................................................................................................................

92

Index.................................................................................................

103

Contents

4

Introduction

Overview

This edition of the Technical Reference contains information about the following printers or multifunction printers (MFPs):

T650n/dn/dtn

T652n/dn/dtn

T654n/dn/dtn X651 MFP X652 MFP X654 MFP X656 MFP X658 MFP

Understanding letters after model numbers

Some Lexmark printers may have one or more letters after the model name to indicate printer features:

 

Acronym

Meaning

 

d

duplex1

 

de

duplex and e-Task (electronic task) touch-screen interface

 

 

 

 

dfe

duplex, finisher/stapler, and e-Task touch-screen interface

 

 

 

 

dhe

duplex, high-capacity drawer, and e-Task touch-screen interface

 

 

 

 

dhn

duplex, high-capacity drawer, and network

 

 

 

 

dme

duplex, mailbox, and e-Task touch-screen interface

 

 

 

 

dn

duplex and network

 

 

 

 

dnf

duplex, network, and finisher/stapler

 

 

 

 

dnw or dw

duplex, network, and wireless

 

 

 

 

dt

duplex and additional tray2

 

dte

duplex, additional tray, and e-Task touch-screen interface

 

 

 

 

dtn

duplex, additional tray, and network

 

 

 

 

dttn

duplex, tandem tray module, and network

 

 

 

 

dtwe

duplex, additional tray, wireless, and e-Task touch-screen interface

 

 

 

 

e

e-Task touch-screen interface

 

 

 

1 Duplex printing (two-sided printing) accomplished by means of an optional duplex unit or an internal duplex unit based on the product.

2 The additional tray is part of a drawer.

Introduction

5

 

Acronym

Meaning

 

hdn

hard disk, duplex, and network

 

 

 

 

n

network

 

 

 

 

nl

network light model

 

 

 

 

ni

network and ImageQuick

 

 

 

 

tn

network and additional tray

 

 

 

1 Duplex printing (two-sided printing) accomplished by means of an optional duplex unit or an internal duplex unit based on the product.

2 The additional tray is part of a drawer.

Introduction

6

Learning abouttheprinter

Finding information about the printer

Setup information

Description

Where to find

The Setup information gives you instructions for setting

You can find the Setup information on the inside of the printer

up the printer. Follow the set of instructions for local,

box or on the Lexmark Web site at www.lexmark.com.

network, or wireless, depending on what you need.

 

 

 

Help

Description

Where to find

 

 

The Help gives you instructions for using the software. While in any Lexmark software program, click Help, Tips Help, or Help Help Topics.

Customer support

 

Description

Where to find (North America)

Where to find (rest of world)

 

Telephone support

Call us at

Telephone numbers and support hours vary by

 

 

US: 1-800-332-4120

country or region.

 

 

 

Monday–Friday (8:00 AM–11:00 PM ET)

Visit our Web site at www.lexmark.com. Select

 

 

 

Saturday (Noon–6:00 PM ET)

a country or region, and then select the

 

 

 

Customer Support link.

 

 

Canada: 1-800-539-6275

 

 

Note: For additional information about

 

 

 

Monday–Friday (8:00 AM–11:00 PM ET)

 

 

 

contacting Lexmark, see the printed warranty

 

 

 

Saturday (Noon–6:00 PM ET)

 

 

 

that came with your printer.

 

 

Mexico: 001-888-377-0063

 

 

 

 

Monday–Friday (8:00 AM–8:00 PM ET)

 

 

 

Note: Telephone numbers and support times

 

 

 

may change without notice. For the most recent

 

 

 

telephone numbers available, see the printed

 

 

 

warranty statement that came with your printer.

 

 

 

 

 

 

E-mail support

For e-mail support, visit our Web site:

E-mail support varies by country or region, and

 

 

www.lexmark.com.

may not be available in some instances.

 

 

1 Click SUPPORT.

Visit our Web site at www.lexmark.com. Select

 

 

2 Click Technical Support.

a country or region, and then select the

 

 

3 Select your printer type.

Customer Support link.

 

 

Note: For additional information about

 

 

4 Select your printer model.

 

 

contacting Lexmark, see the printed warranty

 

 

5 From the Support Tools section, click e-Mail

 

 

that came with your printer.

 

 

 

Support.

 

 

 

6 Complete the form, and then click Submit

 

 

 

 

Request.

 

 

 

 

 

 

Learning about the printer

7

Lexmark X656 MFP, X654 MFP, X651 MFP, X658 MFP, X652 MFP User Manual

Printer Control Language (PCL) page formatting

For more information on PCL, refer to the Printer Languages and Interfaces Technical Reference. It contains a complete listing with descriptions of PCL commands.

To determine which PCL commands your printer supports, see “Appendix A: PCL support” on page 24.

Printable areas

The printable areas and logical pages for PCL emulation (both portrait and landscape orientation) are illustrated below. See the legend that follows for definitions of areas A through I.

Legend:

A Portrait physical page width and landscape physical page length

B Portrait physical page length and landscape physical page width

C Portrait logical page width

D Landscape logical page width

E Distance between the side edge of the physical page and the logical page in portrait

F Distance between the side edge of the physical page and the logical page in landscape

G Distance between the top and bottom edge of the physical page and logical page

HDistance between the left and right edge of the physical page and the printable area in portrait, or distance between the top and bottom edge of the physical page and printable area in landscape

Printer Control Language (PCL) page formatting

8

Legend:

IDistance between the top and bottom edge of the physical page and the printable area in portrait, or distance between the left and right edge of the physical page and the printable area in landscape

Note: The tables that follow in this chapter list the page sizes and dimensions of each area labeled on the preceding diagram for all paper and envelope sizes your printer supports.

Supported paper and envelope dimensions

The following table lists the page sizes and print area dimensions for all supported paper and envelope sizes. For more information about the printable areas and logical pages for PCL emulation, see “Printable areas” on page 8.

 

Selection

 

Paper/envelope

Dimensions by area (pels)1

 

 

 

 

 

 

 

 

dimensions

 

 

 

 

 

 

 

 

 

 

 

Page size

Name

mm

inches

A

B

C

D

E

F

G

H

I

 

parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Paper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13, 613

A5

148 x 210

5.83 x 8.27

3496

4960

3196

4720

142

118

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12, 45, 612

JIS B5

182 x 257

7.2 x 10.1

4300

6070

4000

5830

150

120

0

100

100

 

 

Paper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26, 626

A4 (198

210 x 297

8.3 x 11.7

4960

7014

4676

6778

142

118

0

80

100

 

 

mm)3

 

 

 

 

 

 

 

 

 

 

 

 

26, 626

A4 (203

210 x 297

8.3 x 11.7

4960

7014

4800

6778

80

118

0

80

100

 

 

mm)3

 

 

 

 

 

 

 

 

 

 

 

 

24

A6

148 x 105

5.8 x 4.1

2480

3496

2199

3260

142

118

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1, 601

Executive

184 x 267

7.25 x 10.5

4350

6300

4050

6060

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2, 602

Letter

216 x 279

8.5 x 11

5100

6600

4800

6360

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3, 603

Legal

216 x 356

8.5 x 14

5100

8400

4800

8160

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 or 10

Folio

216 x 330

8.5 x 13

5100

7800

4800

7560

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

Statement

139.7 x 215.9

5.5 x 8.5

3300

5100

3000

4860

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

101

Universal

216 x 356

8.5 x 14

1800–

1800–

1500–

1500–

150

120

0

100

100

 

 

 

 

 

51004

85024

48004

82624

 

 

 

 

 

1 Pel dimensions are for 600 dpi.

2 Page Size Parameters are explained in the Page Control table in the PCL chapter in the Printer Language and Interfaces Technical Reference.

3 The width of the logical page for A4 paper can be changed from the printer control panel or your software application.

4 For the Universal paper size, the area dimensions are listed in pel ranges.

5 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.

Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter in the Printer Language and Interfaces Technical Reference.

Printer Control Language (PCL) page formatting

9

 

Selection

 

Paper/envelope

Dimensions by area (pels)1

 

 

 

 

 

 

 

 

dimensions

 

 

 

 

 

 

 

 

 

 

 

Page size

Name

mm

inches

A

B

C

D

E

F

G

H

I

 

parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

300

Oficio

216 x 340

8.5 x 13.4

5100

8040

4800

7800

150

120

0

100

100

 

 

(Mexico)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Envelope

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90

DL

220 x 110

8.66 x 4.33

2598

5196

2314

4960

142

118

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

91

C5

229 x 162

9.02 x 6.38

3826

5408

3542

5172

142

118

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

995, 100

B5

250 x 176

9.84 x 6.93

4156

5904

3872

5668

142

118

0

100

100

 

 

Envelope

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

600

Other

216 x 356

8.5 x 14

5100

8400

4800

8160

150

120

0

100

100

 

 

Envelope

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

89

9 (Com 9)

225 x 98

8.875 x 3.875

2324

5324

2024

5084

150

120

0

100

100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

81

10 (Com

241 x 105

9.5 x 4.125

2474

5700

2174

5460

150

120

0

100

100

 

 

10)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

80

7 3/4

98 x 191

3.875 x 7.5

2324

4500

2024

4260

150

120

0

100

100

 

 

(Monarch)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Pel dimensions are for 600 dpi.

2 Page Size Parameters are explained in the Page Control table in the PCL chapter in the Printer Language and Interfaces Technical Reference.

3 The width of the logical page for A4 paper can be changed from the printer control panel or your software application.

4 For the Universal paper size, the area dimensions are listed in pel ranges.

5 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.

Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item” in the PCL chapter in the Printer Language and Interfaces Technical Reference.

Printer Control Language (PCL) page formatting

10

Printer JobLanguage(PJL)

PJL commands information

Your printer supports complete PJL commands, including certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS).

For a complete listing with descriptions of PJL commands, see the Printer Languages and Interfaces Technical Reference.

To determine which commands your printer supports, see “Appendix B: PJL support” on page 34.

Printer Job Language (PJL)

11

PostScript(PS)emulation

Your printer supports complete PostScript emulation supplemental operators. For full descriptions in detail for these operators, refer to the PostScript emulation chapter in the Printer Languages and Interfaces Technical Reference.

To determine which commands your printer supports, see “Appendix C: PostScript support” on page 77.

Paper sizes supported

 

= Supported

 

 

 

 

 

 

X = Not supported

 

 

 

 

 

 

Paper sizes

 

 

 

 

Printer models

 

Size

 

Literal name

Size (mm)

Size (inches)

Size (points)

T650n/dn/dtn,

X651 MFP,

 

 

 

 

 

 

 

T652n/dn/dtn,

X652 MFP,

 

 

 

 

 

 

 

T654n/dn/dtn

X654 MFP,

 

 

 

 

 

 

 

 

X656 MFP,

 

 

 

 

 

 

 

 

X658 MFP

 

Letter

 

letter

215.9 x 279.4

8.5 x 11.0

612 x 792

 

 

 

 

 

 

 

 

 

 

 

 

Legal

 

legal

215.9 x 355.6

8.5 x 14.0

612 x 1008

 

 

 

 

 

 

 

 

 

 

 

 

JIS B5

 

b5*

182.0 x 257.0

7.2 x 10.1

516 x 729

 

 

 

 

 

 

 

 

 

 

 

 

A4

 

a4

210.0 x 297.0

8.3 x 11.7

595 x 842

 

 

 

 

 

 

 

 

 

 

 

 

Executive

 

executivepage

184.2 x 266.7

7.25 x 10.5

522 x 756

 

 

 

 

 

 

 

 

 

 

 

 

A5

 

a5

148.0 x 210.0

5.83 x 8.27

419 x 595

 

 

 

 

 

 

 

 

 

 

 

 

Oficio

 

oficio

215.9 x 340.4

8.5 x 13.4

612 x 965

 

 

 

 

 

 

 

 

(Lexmark unique

 

 

 

 

 

 

 

 

size)

 

 

 

 

 

 

 

 

612 x 972 (official

 

 

 

 

 

 

 

 

Postscript size)

 

 

 

 

 

 

 

 

 

 

 

 

Folio

 

folio

215.9 x 330.2

8.5 x 13.0

612 x 936

 

 

 

 

 

 

 

 

 

 

 

 

Statement

 

statement

139.7 x 215.9

5.5 x 8.5

396 x 612

 

 

 

 

 

 

 

 

 

 

 

 

A6

 

a6

105.0 x 148.0

4.13 x 5.83

297 x 419

 

 

 

 

 

 

 

 

 

 

 

 

Universal

 

universal

216 x 356

8.5 x 14

612 x 1008

 

 

 

 

 

 

 

 

 

 

 

 

Custom

 

custom

215.9 x 355.6

8.5 x 14.0

612 x 1020

 

 

 

 

 

 

 

 

 

 

 

 

Custom

 

custom

297 x 431.8

11.7 x 17

842 x 1224

X

X

 

 

 

 

 

 

 

 

 

 

Custom

 

custom

320 x 559

12.6 x 22

908 x 1584

X

X

 

 

 

 

 

 

 

 

 

* This is a Japanese Industry Standard (JIS) paper size. The same named designation is used by JIS and International Standards Organization (ISO) for different paper sizes.

PostScript (PS) emulation

12

 

= Supported

 

 

 

 

 

 

X = Not supported

 

 

 

 

 

 

Paper sizes

 

 

 

 

Printer models

 

Size

 

Literal name

Size (mm)

Size (inches)

Size (points)

T650n/dn/dtn,

X651 MFP,

 

 

 

 

 

 

 

T652n/dn/dtn,

X652 MFP,

 

 

 

 

 

 

 

T654n/dn/dtn

X654 MFP,

 

 

 

 

 

 

 

 

X656 MFP,

 

 

 

 

 

 

 

 

X658 MFP

 

Custom

 

custom

297 x 914

11.7 x 36

842 x 2592

X

X

 

 

 

 

 

 

 

 

 

* This is a Japanese Industry Standard (JIS) paper size. The same named designation is used by JIS and International Standards Organization (ISO) for different paper sizes.

PostScript paper tray support

When the printer receives one of the operators listed in “Tray selected with tray operators” on page 14, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray.

The printer checks the value of manualfeed in statusdict and the ManualFeed page device parameter. If either one is true, the printer sends a message to load the requested size in the manual feed tray or multipurpose feeder.

The PageSize Policy is set to 0 by means of setpagedevice.

The printer checks the paper size loaded in the current active source to determine if it matches the requested size. If the sizes match, the paper is fed from the active source.

Note: The current active tray is the last source that was selected from the printer control panel or by the printer language.

If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.

If the requested media size is not found by the previous search, the following search order is used:

Tray 1

Tray 2

Tray 3

Multipurpose Feeder

Tray 4

Tray 5

If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed.

For printers that support automatic duplexing:

Automatic duplexing is not supported for custom-size paper or for envelopes in the multipurpose feeder. Automatic duplexing is supported from the multipurpose feeder for all other papers.

If the paper source is changed before the back side of a duplexed page prints, a blank back page prints, the paper source changes, and the information for the back side of the page is printed on the front side of a page sent from the new paper source.

When these operators are used, it is equivalent to executing the following PostScript emulation sequence:

<< /PageSize [x y]/ImagingBBox null /Policies << /PageSize 0>> >>

PostScript (PS) emulation

13

setpagedevice

where x y are the PageSize in points.

Tray selected with tray operators

 

= Supported

 

 

 

X = Not supported

Printer models

 

Operator

Tray selected (corresponding

T650n/dn/dtn, T652n/dn/dtn,

X651 MFP, X652 MFP,

 

 

image size is set)

T654n/dn/dtn

X654 MFP, X656 MFP,

 

 

 

 

X658 MFP

 

a4tray

tray with A4-size paper

 

 

 

 

 

 

 

 

a5tray

tray with A5-size paper

 

 

 

 

 

 

 

 

b5tray

tray with B5-size paper

 

 

 

 

 

 

 

 

customtray

tray with custom-size paper

X

X

 

 

 

 

 

 

executivetray

tray with executive-size paper

 

 

 

 

 

 

 

 

foliotray

tray with folio-size paper

 

 

 

 

 

 

 

 

legaltray

tray with legal-size paper

 

 

 

 

 

 

 

 

lettertray

tray with letter-size paper

 

 

 

 

 

 

 

 

oficiotray

tray with oficio-size paper

 

 

 

 

 

 

 

 

statementtray

tray with statement-size paper

 

 

 

 

 

 

 

PostScript envelope size support

The literal names in “Envelope sizes supported” on page 15 are also supported as operators in userdict. These operators change the image size, but do not change the active paper source. Therefore, when these operators are used, part of the image may be clipped.

When these literal names are used as operators, it is equivalent to executing the following PostScript emulation sequence. The following example uses a 3.875 x 7.5 envelope.

<</Policies <</PageSize 7>> /PageSize [279 540]>> >>setpagedevice

PostScript (PS) emulation

14

Envelope sizes supported

 

= Supported

 

 

 

 

 

 

 

X = Not supported

 

 

 

 

 

 

Envelope sizes

 

 

 

 

Printer models

 

Size name

Literal name

Size (mm)

Size (inches)

Size

T650n/dn/dtn,

X651 MFP,

 

 

 

 

 

(points)

T652n/dn/dtn,

X652 MFP,

 

 

 

 

 

 

T654n/dn/dtn

X654 MFP,

 

 

 

 

 

 

 

X656 MFP,

 

 

 

 

 

 

 

X658 MFP

 

7 3/4

3.875x7.5envelope

98.4 x 190.5

3.875 x 7.5

279 x 540

 

 

 

 

 

 

 

 

 

 

 

Commercial 9

3.875x8.875envelope

98.4 x 225.4

3.875 x 8.875

279 x 639

 

 

 

 

 

 

 

 

 

 

 

Commercial 10

4.125x9.5envelope

104.8 x 241.3

4.125 x 9.5

297 x 684

 

 

 

 

 

 

 

 

 

 

 

International DL

110x220envelope

110 x 220

4.33 x 8.66

312 x 624

 

 

 

 

 

 

 

 

 

 

 

International C5

162x229envelope

162 x 229

6.38 x 9.01

459 x 649

 

 

 

 

 

 

 

 

 

 

 

International B5

176x250envelope

176 x 250

6.93 x 9.84

499 x 708

 

 

 

 

 

 

 

 

 

 

 

Other envelope

otherenvelope

296.93 x 427.48

11.69 x 16.83

841 x 842

X

X

 

 

 

 

 

 

 

 

 

otherenvelope*

Other

229.11 x 355.6

9.02 x 14

612 x 996

 

 

 

 

 

 

 

 

 

 

* For other envelopes, the page is formatted to 216 x 356 mm (8.5 x 14 in.) unless a size is specified by your software program.

Literal names supported

= Supported

 

X = Not Supported

 

Literal names

Printer models

Literal name

Compatible literal name

T650n/dn/dtn, T652n/dn/dtn,

X651 MFP, X652 MFP,

 

 

T654n/dn/dtn

X654 MFP, X656 MFP,

 

 

 

X658 MFP

monarchenvelope

3.875x7.5envelope

 

 

com10envelope

4.125x9.5envelope

 

 

dlenvelope

110x220envelope

 

 

c5envelope

162x229envelope

 

 

b5envelope

176x250envelope

 

 

PostScript (PS) emulation

15

PostScript envelope tray support

If manualfeed in statusdict and the ManualFeed page device parameter are false when the printer receives one of the envelopetray operators listed in “Envelopetray operator selections” on page 16, then the printer:

Sets the PageSize Policy to 0.

Checks the active source to see if it matches the requested envelope size. If the sizes match, the envelope is fed from the active source.

Note: The active source is the last source selected from the printer control panel or data stream.

If the requested size and the size loaded in the active source do not match, the sources are searched in the order defined by the Priority array in the InputAttributes dictionary in the pagedevice dictionary.

If the requested media size is not found by the previous search, the following search order is used:

Envelope Feeder

Multipurpose Feeder

If the requested size andtype are not availablefrom any automatic source, you are prompted to load therequested envelope size and type in the manual feed source.

If the size is still not available, a configurationerror is issued and the print job is flushed.

If manualfeed or ManualFeed is true, the printer prompts you to load the requested size manually. If no manual feed exists on the printer, a rangecheck error message is generated

The envelope tray the printer selects when it receives an envelopetray operator is listed in “Envelopetray operator selections” on page 16. These operators are equivalent to executing the following PostScript emulation sequence:

<</PageSize [x y] /ImagingBBox null /Policies<</PageSize 0>> >> setpagedevice

where x y are the PageSize in points.

Envelopetray operator selections

 

= Supported

 

 

 

 

 

X = Not supported

 

 

 

 

 

Tray operators

 

 

Printer models

 

Operator

Tray selected (Corresponding

T650n/dn/dtn,

 

X651 MFP, X652 MFP,

 

 

image size is set)

T652n/dn/dtn,

 

X654 MFP, X656 MFP,

 

 

 

T654n/dn/dtn

 

X658 MFP

 

110x220envelopetray

tray with 110 x 220 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

dlenvelopetray

tray with 110 x 220 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

162x229envelopetray

tray with 162 x 229 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

c5envelopetray

tray with 162 x 229 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

176x250envelopetray

tray with 176 x 250 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

PostScript (PS) emulation

16

 

= Supported

 

 

 

 

 

X = Not supported

 

 

 

 

 

Tray operators

 

 

Printer models

 

Operator

Tray selected (Corresponding

T650n/dn/dtn,

 

X651 MFP, X652 MFP,

 

 

image size is set)

T652n/dn/dtn,

 

X654 MFP, X656 MFP,

 

 

 

T654n/dn/dtn

 

X658 MFP

 

b5envelopetray

tray with 176 x 250 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

3.875x7.5envelopetray

tray with 3.875 x 7.5 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

monarcenvelopetray

tray with 3.875 x 7.5 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

3.875x8.875envelopetray

tray with 3.875 x 8.875 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

4.125x9.5envelopetray

tray with 4.125 x 9.5 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

com10envelopetray

tray with 4.125 x 9.5 size

 

 

 

 

 

envelopes

 

 

 

 

 

 

 

 

 

 

otherenvelopetray

tray with other size envelopes

 

 

 

 

 

 

 

 

 

PostScript (PS) emulation

17

Printer specifications

This chapter lists printer specifications and information about hardware, environmental conditions, and power requirements.

Airflow requirement

The room should meet ASHRAE 62—1989 standards.

Noise emission levels

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

 

 

 

 

1-meter average sound pressure, dBA

 

 

 

Status

T650n

T652n/dn

T654n/dn

X651 MFP,

X654 MFP,

X658 MFP

 

 

 

 

 

 

X652 MFP

X656 MFP

 

 

Printing

53

(simplex)

54

(simplex)

55

(simplex)

54

(simplex)

56

(simplex)

55

(simplex)

 

56

(duplex)

54

(duplex)

56

(duplex)

54

(duplex)

56

(duplex)

55

(duplex)

 

 

 

 

 

 

 

 

 

 

Scanning

Not applicable

Not applicable

Not applicable

56

 

55

 

55

 

 

 

 

 

 

 

 

 

 

 

Copying

Not applicable

Not applicable

Not applicable

55

 

56

 

55

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quiet Mode

47

 

51

 

51

 

51

 

52

 

50

 

printing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standby (Idle

26

 

30

 

30

 

29

 

29

 

28

 

without Power

 

 

 

 

 

 

 

 

 

 

 

 

Saver)

 

 

 

 

 

 

 

 

 

 

 

 

Note: Measurements apply to 300-dpi, 600-dpi, and 1200-dpi printing.

 

 

 

 

 

Declared sound power level, Bels

 

 

 

 

Status

T650n

T652n/dn

T654n/dn

X651 MFP,

X654 MFP,

X658 MFP

 

 

 

 

 

 

X652 MFP

X656 MFP

 

 

Printing

6.8

(simplex)

7.0

(simplex)

7.1

(simplex)

6.9

(simplex)

7.1

(simplex)

7.1

(simplex)

 

7.1

(duplex)

7.0

(duplex)

7.2

(duplex)

6.9

(duplex)

7.1

(duplex)

7.1

(duplex)

 

 

 

 

 

 

 

 

 

 

 

 

 

Idle (Standby

4.1

 

4.5

 

4.5

 

4.5

 

4.5

 

4.5

 

mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Scanning

Not applicable

Not applicable

Not applicable

7.2

 

7.2

 

7.2

 

 

 

 

 

 

 

 

 

 

 

Copying

Not applicable

Not applicable

Not applicable

7.0

 

7.1

 

7.2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quiet Mode

6.2

 

6.7

 

6.7

 

6.7

 

6.7

 

6.6

 

printing

 

 

 

 

 

 

 

 

 

 

 

 

Note: Measurements apply to 300-dpi, 600-dpi, and 1200-dpi printing.

Printer specifications

18

Electrical specifications

Printer model

Electrical specification

T65x low voltage models*

100–127 V at 47–63 Hz, nominal

 

90–137 V, extreme

 

 

T65x high voltage models

220–240 V at 47–63 Hz, nominal (not available in all countries)

 

198–254 V, extreme

 

 

X65x MFP low voltage models

100–127 V at 50–60 Hz, nominal

 

90–137 V, extreme

 

 

X65x MFP high voltage models

220–240 V at 50–60 Hz, nominal (not available in all countries)

 

198–259 V, extreme

* Using a 220–110 power converter with 110 V printer is not recommended.

Warning—Potential Damage: Lexmark recommends that you do not use voltage converters with printers.

Power requirements

The following tables list the nominal average power requirements (including fuser power).

Lexmark T65x nominal average power requirements

 

Printing states

T650n

T652n

T654n

 

Average power while printing continuously

 

 

 

 

 

 

 

 

 

1-sided (simplex)

640 W

725 W

740 W

 

2-sided (duplex)

540 W

565 W

575 W

 

 

 

 

 

 

Average power while idle

 

 

 

 

 

 

 

 

 

Power Saver on

12 W

13 W

14 W

 

Ready mode

80 W

85 W

85 W

 

 

 

 

 

 

Max current while printing

 

 

 

 

 

 

 

 

 

100–110 V

8.7 A

8.7 A

8.7 A

 

110–127 V

7.6 A

7.6 A

7.6 A

 

220–240 V

4.1 A

4.1 A

4.1 A

 

 

 

 

 

Lexmark X65x nominal average power requirements

 

Printing states

X651 MFP, X652 MFP

X654 MFP, X656 MFP

X658 MFP

 

Printing continuously

700 W

800 W

800 W

 

 

 

 

 

 

Copying continuously

765 W

875 W

875 W

 

 

 

 

 

 

Scanning continuously

165 W

165 W

165 W

 

 

 

 

 

Printer specifications

19

 

Printing states

X651 MFP, X652 MFP

X654 MFP, X656 MFP

X658 MFP

 

Average power while idle

 

 

 

 

 

 

 

 

 

Power Saver on

24 W

28 W

30 W

 

Ready (Standby mode)

105 W

105 W

105 W

 

 

 

 

 

 

Average current while printing

 

 

 

 

 

 

 

 

 

100 V

9.8 A

9.8 A

9.9 A

 

120 V

8.1 A

8.1 A

8.5 A

 

230 V

4.3 A

4.3 A

4.5 A

 

 

 

 

 

Physical specifications

Lexmark T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn dimensions

 

 

Height

Width

Depth

Weight

 

T650n base printer

348 mm (13.7 in.)

425 mm (16.7 in.)

493 mm (19.4 in.)

18.4 kg (40.6 lb)

 

 

 

 

 

 

 

T650dn configured with an optional duplex

402 mm (15.8 in.)

425 mm (16.7 in.)

640 mm (25.2 in.)

23.4 kg (51.6 lb)

 

unit

 

 

 

 

 

 

 

 

 

 

 

T650dn configured with an additional

533 mm (24.2 in.)

425 mm (16.7 in.)

640 mm (25.2 in.)

27.4 kg (60.4 lb)

 

550-sheet drawer

 

 

 

 

 

 

 

 

 

 

 

T652n/dn base printer

425 mm (16.7 in.)

425 mm (16.7 in.)

510 mm (20.1 in.)

23 kg (50.7 lb)

 

 

 

 

 

 

 

T652dn configured with an additional

557 mm (21.7 in.)

425 mm (16.7 in.)

510 mm (20.1 in.)

59.5 kg (27 lb)

 

550-sheet drawer

 

 

 

 

 

 

 

 

 

 

 

T654n/dn base printer

438 mm (17.2 in.)

425 mm (16.7 in.)

510 mm (20.1 in.)

23.4 kg (51.6 lb)

 

 

 

 

 

 

 

T654dn configured with an additional

568 mm (22.4 in.)

425 mm (16.7 in.)

510 mm (20.1 in.)

60.4 kg (27.4 lb)

 

550-sheet drawer

 

 

 

 

 

 

 

 

 

 

Input options for Lexmark T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

Option name

Height

Width

Depth

Weight

Duplex unit (attached to the T650 only)

54 mm (2.1 in.)

421 mm (16.6 in.)

640 mm (25.2 in.)

5 kg (11 lb)

 

 

 

 

 

550-sheet drawer

130 mm (5.1 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

4 kg (8.8 lb)

 

 

 

 

 

550-sheet tray

121 mm (4.8 in.)

421 mm (16.6 in.)

506 mm (19.9 in.)

1.4 kg (3.1 lb)

 

 

 

 

 

250-sheet drawer

90 mm (3.5 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

3.2 kg (7.1 lb)

 

 

 

 

 

250-sheet tray

56 mm (2.2 in.)

421 mm (16.6 in.)

488 mm (19.2 in.)

0.9 kg (2 lb)

 

 

 

 

 

2000-sheet drawer

357 mm (14.1 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

16.8 kg (37 lb)

 

 

 

 

 

200-sheet universally adjustable drawer

90 mm (3.5 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

3.2 kg (7.1 lb)

 

 

 

 

 

200-sheet universally adjustable tray

56 mm (2.2 in.)

421 mm (16.6 in.)

488 mm (19.2 in.)

0.9 kg (2 lb)

 

 

 

 

 

400-sheet universally adjustable drawer

130 mm (5.1 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

4 kg (8.8 lb)

* The envelope feeder fits within the height and width of the printer.

Printer specifications

20

Option name

Height

Width

Depth

Weight

400-sheet universally adjustable tray

121 mm (4.8 in.)

421 mm (16.6 in.)

506 mm (19.9 in.)

1.4 kg (3.1 lb)

 

 

 

 

 

Envelope feeder (closed position)

*

*

233 mm (9.2 in.)

2 kg (4.4 lb)

 

 

 

 

 

Envelope feeder (support fully extended)

*

*

350 mm (13.8 in.)

2 kg (4.4 lb)

* The envelope feeder fits within the height and width of the printer.

Output options for Lexmark T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

 

Option name

Height

Width

Depth

Weight

 

Output expander

160 mm (6.2 in.)

421 mm (16.6 in.)

378 mm (14.9 in.)

2.8 kg (5.7 lb)

 

 

 

 

 

 

 

5-bin mailbox

315 mm (12.4 in.)

421 mm (16.6 in.)

330 mm (12.9 in.)

5.2 kg (11.5 lb)

 

 

 

 

 

 

 

High capacity output stacker

323 mm (12.7 in.)

421 mm (16.6 in.)

378 mm (14.9 in.)

4.5 kg (9.9 lb)

 

 

 

 

 

 

 

StapleSmartTM II

320.4 mm (12.6 in.)

433 mm (17.1 in.)

403 mm (15.9 in.)

7.2 kg (15.9 lb)

Furniture for Lexmark T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

 

Furniture name

Height

Width

Depth

Weight

 

Spacer

130 mm (5.1 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

3.4 kg (7.5 lb)

 

 

 

 

 

 

 

T65x caster base

107 mm (4.2 in.)

768 mm (30.2 in.)

801 mm (31.5 in.)

38.5 kg (84.9 lb)

 

 

 

 

 

 

Lexmark X651de MFP, X652de MFP, X654de MFP, X656de MFP dimensions - unpackaged

 

 

Height

Width

Depth

Weight with cartridge

 

Base MFP

755 mm (29.7 in.)

548 mm (21.6 in.)

611 mm (24.1 in.)

45.4 kg (100 lb)

 

 

 

 

 

 

 

550-sheet drawer

130.4 mm (5.1 in.)

421 mm (16.6 in.)

510.2 mm (20.1 in.)

4.1 kg (9 lb)

 

 

 

 

 

 

 

250-sheet drawer

89.6 mm (3.5 in.)

421 mm (16.6 in.)

510.2 mm (20.1 in.)

3.2 kg (7 lb)

 

 

 

 

 

 

 

2000-sheet drawer

357 mm (14.1 in.)

421 mm (16.6 in.)

510.2 mm (20.1 in.)

16.8 kg (37 lb)

 

 

 

 

 

 

 

Caster base

107.5 mm (4.2 in.)

778 mm (30.6 in.)

803 mm (31.6 in.)

36.3 kg (80 lb)

 

 

 

 

 

 

Lexmark X656dte MFP preconfigured dimensions - unpackaged

 

 

Height

Width

Depth

Weight with cartridge

 

dte

885.4 mm (34.8 in.)

548 mm (21.6 in.)

611 mm (24.1 in.)

49.5 kg (109 lb)

 

 

 

 

 

 

 

250-sheet drawer

89.6 mm (3.5 in.)

421 mm (16.6 in.)

510.2 mm (20.1 in.)

4.1 kg (9 lb)

 

 

 

 

 

 

 

550-sheet drawer

130.4 mm (5.1 in.)

421 mm (16.6 in.)

510.2 mm (20.1 in.)

4.1 kg (9 lb)

 

 

 

 

 

 

 

2000-sheet drawer

357 mm (14.1 in.)

421 mm (16.6 in.)

510 mm (20.1 in.)

16.8 kg (37 lb)

 

 

 

 

 

 

 

Caster base

107.5 mm (4.2 in.)

778 mm (30.6 in.)

803 mm (31.6 in.)

36.3 kg (80 lb)

 

 

 

 

 

 

Printer specifications

21

X658dxe MFP dimensions - unpackaged

 

Height

Width

Depth

Weight with cartridge

de, dfe, dme

1114 mm (43.9 in.)

548 mm (21.6 in.)*

596 mm (23.5 in.)*

de: 75 kg (165.3 lb)

 

 

 

 

dfe: 75.1 kg (165.5 lb)

 

 

 

 

dme: 72.8 kg (160.6 lb)

 

 

 

 

 

Models configured with an

1246 mm (49.1 in.)

548 mm (21.6 in.)*

596 mm (23.5 in.)*

de: 80 kg (176.3 lb)

additional drawer

 

 

 

dfe: 80.1 kg (176.5 lb)

 

 

 

 

dme: 77.8 kg (171.5 lb)

 

 

 

 

 

MFP with all options - maximum

1378 mm (54.3 in.)

548 mm (21.6 in.)*

596 mm (23.5 in.)*

de: 85 kg (187.3 lb)

dimensions

 

 

 

dfe: 85.1 kg (187.5 lb)

 

 

 

 

 

 

 

 

dme: 82.8 kg (182.6 lb)

 

 

 

 

 

550-sheet drawer option

132 mm (5.2 in.)

548 mm (21.6 in.)

548 mm (21.6 in.)

5 kg (11 lb)

 

 

 

 

 

Optional envelope feeder (closed

193 mm (7.6 in.)

421 mm (16.6 in.)

233 mm (9.2 in.)

2 kg (4.4 lb)

position)

 

 

 

 

 

 

 

 

 

Optional envelope feeder (support

193 mm (7.6 in.)

421 mm (16.6 in.)

350 mm (13.8 in.)

2 kg (4.4 lb)

fully extended)

 

 

 

 

 

 

 

 

 

Caster base

89 mm (3.5 in.)*

915 mm (36 in.)

771 mm (30.4 in.)

13.6 kg (30 lb)

* The bottom drawer fits 43 mm (1.7 in.) into the base.

Physical dimensions with extensions in open positions

 

Printer model

Height

Width

Depth

 

X651de, X652de, X654de, X656de

755 mm (29.7 in.)

548 mm (21.6 in.)

790 mm (31.1 in.)

 

 

 

 

 

 

X656dte

885.4 mm (34.8 in.)

548 mm (21.6 in.)

790 mm (31.1 in.)

 

 

 

 

 

 

X658de/dfe/dme

1114 mm (43.9 in.)

548 mm (21.6 in.)

787 mm (31 in.)

 

 

 

 

 

 

X658dte/dtfe/dtme

1246 mm (49.1 in.)

548 mm (21.6 in.)

787 mm (31 in.)

 

 

 

 

 

Clearance requirements

Lexmark T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

Model

Left side

Right side

Front

Rear

Top

T650n/dn/dtn, T652n/dn/dtn,

305 mm (12 in.)

305 mm (12 in.)

508 mm (20 in.)

305 mm (12 in.)

115 mm (4.5 in.)

T654n/dn/dtn

 

 

 

 

 

 

 

 

 

 

 

Lexmark X651 MFP, X652 MFP, X654 MFP, X656 MFP, X658 MFP

Model

Left side

Right side

Front

Rear

Top

X651 MFP, X652 MFP,

304.8 mm (12 in.)

203.2 mm (8 in.)

508 mm (20 in.)

203.2 mm (8 in.)

304.8 mm (12 in.)

X654 MFP, X656 MFP,

 

 

 

 

 

X658 MFP

 

 

 

 

 

 

 

 

 

 

 

Printer specifications

22

Environmental conditions

Note: When shipping or storing printers, always pack the printer supplies (cartridges and photoconductors, for example) separately.

Air temperature ranges

 

Printer model

Operating value

Shipping value

Storage (unpacked)

 

T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

15.6–32.2°C (60–90°F)

-40–43.3°C (-40–110°F)

0–40°C (32–104°F)

 

 

 

 

 

 

X651 MFP, X652 MFP, X654 MFP, X656 MFP,

15.6–32.2°C (60–90°F)

-40–43.3°C (-40–110°F)

0–40°C (32–104°F)

 

X658 MFP

 

 

 

 

 

 

 

 

Humidity ranges

Printer model

Operating value

Shipping value

Storage value

T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

8%–80%*

5%–95%

5%–80%

 

 

 

 

X651 MFP, X652 MFP, X654 MFP, X656 MFP, X658 MFP

8%–80%*

5%–95%

8%–80%

* Approaching 32°C (90°F) the maximum relative humidity is 60%.

Altitude specifications and atmospheric pressure

Altitude specifications

 

 

 

Altitude (above sea level)

 

Printer model

Operating

Shipping/storage

 

T650n/dn/dtn, T652n/dn/dtn, T654n/dn/dtn

0–3048 M (10,000 ft.)

0.25 atmospheric pressure (equal to 10,300 M

 

 

 

[34,000 ft.]

 

 

 

 

 

X651 MFP, X652 MFP, X654 MFP, X656 MFP,

0–3048 M (10,000 ft.)

Less than 10,300 M (34,000 ft.)

 

X658 MFP

 

 

 

 

 

 

Atmospheric Pressure

74.6 kPa

Printer specifications

23

Appendix A:PCLsupport

PCL emulation commands

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESCE

Printer Reset

 

 

ESCY

Display Functions-On

 

 

ESCZ

Display Functions-Off

 

 

ESCz

Print Test Page

X

X

ESC&a#C

Horizontal Cursor Position

 

 

 

(in Columns)

 

 

ESC&a#G

Duplex Page Side Selection

 

 

ESC&a#H

Horizontal Cursor Position

 

 

 

(in Decipoints)

 

 

ESC&a#L

Set Left Margin

 

 

ESC&a#M

Set Right Margin

 

 

ESC&a#N

Negative Motion

X

X

ESC&a#P

Print Direction

 

 

ESC&a#R

Vertical Cursor Position (in Rows)

 

 

ESC&a#V

Vertical Cursor Position

 

 

 

(in Decipoints)

 

 

ESC&b#M

Monochrome Print Mode

 

 

ESC&b#W[data]

Configuration Command

X

X

ESC&c#T

Character Text Path Direction

 

 

ESC&d@

Underline-Disable

 

 

ESC&d#A

Number of Collated Copies

 

 

ESC&d#D

Underline-Enable

 

 

ESC&f#F

Set Universal Height

 

 

Appendix A: PCL support

24

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESC&f#G

Set Universal Width

 

 

ESC&f#O

Set Universal Feed Direction

 

 

ESC&f#W

Set Universal Custom Name

 

 

ESC&f#S

Push / Pop Cursor Position

 

 

ESC&f#X

Macro Control

 

 

ESC&f#Y

Set Macro ID

 

 

ESC&k#G

Set Line Termination

 

 

ESC&k#H

Set Horizontal Motion Index

 

 

ESC&k#S

Select Primary and Secondary Pitch

 

 

ESC&k#W

Text Scale Mode

 

 

ESC&l#A

Set Page Size

 

 

ESC&l#C

Set Vertical Motion Index

 

 

ESC&l#D

Set Line Spacing

 

 

ESC&l#E

Set Top Margin

 

 

ESC&l#F

Set Text Length

 

 

ESC&l#G

Set Output Bin

 

 

ESC&l#H

Paper Source

 

 

ESC&l#L

Skip Perforation

 

 

ESC&l#O

Select Orientation

 

 

ESC&l#M(b)

Paper Type

X

X

ESC&l#P

Set Page Length

 

 

ESC&l#S

Simplex/Duplex Print

 

 

ESC&l1T

Job Separation

X

X

ESC&l#U

Long-Edge Offset Registration

 

 

ESC&l#X

Number of Copies

 

 

Appendix A: PCL support

25

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESC&l#Z

Short-Edge Offset Registration

 

 

ESC&n#W [operation] [string id]

Alphanumeric ID

 

 

ESC&p#C

Palette Control

 

 

ESC&p#I

Palette Control ID

 

 

ESC&p#S

Select Palette

 

 

ESC&p#X[data]

Transparent Print Data

 

 

ESC&r#F

Flush All Pages

 

 

ESC&s#C

End-Of-Line Text Wrap

 

 

ESC&t#P

Text Parsing Method

 

 

ESC&u#D

Unit of Measure

 

 

ESC(#

Primary Font Symbol Set

 

 

ESC(#X

Select Primary Download Font

 

 

 

(by Font ID)

 

 

ESC(3@

Select Default Primary Font

 

 

ESC(f#W[data]

Define Symbol Set

 

 

ESC(s#B

Primary Font Stroke Weight

 

 

ESC(s#H

Primary Font Pitch

 

 

ESC(s#P

Primary Font Spacing

 

 

ESC(s#S

Primary Font Style

 

 

ESC(s#T

Primary Font Typeface Selection

 

 

ESC(s#V

Primary Font Height (Point Size)

 

 

ESC(s#W[data]

Load Character

 

 

ESC)#

Secondary Font Symbol Set

 

 

ESC)#X

Select Secondary Download Font

 

 

 

(by Font ID)

 

 

ESC)3@

Select Default Secondary Font

 

 

Appendix A: PCL support

26

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESC)s#B

Secondary Font Stroke Weight

 

 

ESC)s#H

Secondary Font Pitch

 

 

ESC)s#P

Secondary Font Spacing

 

 

ESC)s#S

Secondary Font Style

 

 

ESC)s#T

Secondary Font Typeface Selection

 

 

ESC)s#V

Secondary Font Height (Point Size)

 

 

ESC)s#W[data]

Load Font Header

 

 

ESC*b#M

Set Raster Compression Mode

 

 

ESC*b#V[data]

Transfer Raster Data (by Plane)

 

 

ESC*b#W[data]

Transfer Raster Data (by Row / Block)

 

 

ESC*b#Y

Y Offset

 

 

ESC*c#A

Horizontal Rectangle Size

 

 

 

(in PCL Units)

 

 

ESC*c#B

Vertical Rectangle Size (in PCL Units)

 

 

ESC*c#D

Set Font ID

 

 

ESC*c#E

Set Character Code

 

 

ESC*c#F

Font Control

 

 

ESC*c#G

Area Fill ID

 

 

ESC*c#H

Horizontal Rectangle Size

 

 

 

(in Decipoints)

 

 

ESC*c#K

GL/2 Horizontal Plot Size (in Inches)

 

 

ESC*c#L

GL/2 Vertical Plot Size (in Inches)

 

 

ESC*c#P

Fill Rectangular Area

 

 

ESC*c#Q

Pattern Control

 

 

ESC*c#R

Symbol Set ID Code

 

 

ESC*c#S

Symbol Set Control

 

 

Appendix A: PCL support

27

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESC*c0T

Set Picture Frame Anchor Point

 

 

ESC*c#V

Vertical Rectangle Size (in Decipoints)

 

 

ESC*c#W[data]

User-Defined Pattern

 

 

ESC*c#X

Picture Frame Horizontal Size

 

 

 

(in Decipoints)

 

 

ESC*c#Y

Picture Frame Vertical Size

 

 

 

(in Decipoints)

 

 

ESC*l#O

Logical Operation

 

 

ESC*l#R

Pixel Placement

 

 

ESC*l#W[data]

Color Lookup Tables

X

X

ESC*m#W[data]

Download Dither Matrix

 

 

ESC*o#M(b)

Print Quality

 

 

ESC*o#Q

Mechanical Print Quality

X

X

ESC*o#W[data]

Driver Configuration Command

 

 

ESC*p#P

Push / Pop Palette

 

 

ESC*p#R

Set Pattern Reference Point

 

 

ESC*p#X

Horizontal Cursor Position

 

 

 

(in PCL Units)

 

 

ESC*p#Y

Vertical Cursor Position (in PCL Units)

 

 

ESC*r#A

Start Raster Graphics

 

 

ESC*r#F

Raster Graphics Presentation Mode

 

 

ESC*r#S

Raster Width (Source)

 

 

ESC*r#T

Raster Height (Source)

 

 

ESC*r#U

Simple Color

 

 

ESC*rB

End Raster Graphics (Version B)

 

 

ESC*rC

End Raster Graphics (Version C)

 

 

ESC*s#I

Inquire Status Readback Entity

 

 

Appendix A: PCL support

28

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

 

 

T652n/dn/dtn,

X656 MFP,

Command

Function

T654n/dn/dtn

X658 MFP

ESC*s1M

Free Space

 

 

ESC*s#T

Set Status Readback Location Type

 

 

ESC*s#U

Set Status Readback Location Unit

 

 

ESC*s#X

Echo

 

 

ESC*t#H

Raster Width Destination

 

 

ESC*t#I

Gamma Correction

 

 

ESC*t#J

Render Algorithm

X

X

ESC*t#K

Scale Algorithm

X

X

ESC*t#R

Raster Resolution

 

 

ESC*t#V

Raster Height Destination

 

 

ESC*g#W

Set Raster Configuration

 

 

ESC*v#A

Color Component One

 

 

ESC*v#B

Color Component Two

 

 

ESC*v#C

Color Component Three

 

 

ESC*v#I

Assign Color Index

 

 

ESC*v#N

Source Transparency Mode

 

 

ESC*v#O

Pattern Transparency Mode

 

 

ESC*v#S

Foreground Color

 

 

ESC*v#T

Select Current Pattern

 

 

ESC*v#W[data]

Configure Image Data

 

 

ESC*i#W[data]

Viewing Illuminant

X

X

ESC9

Clear Horizontal Margins

 

 

ESC=

Half Line-Feed

 

 

ESC%#A

Enter PCL Emulation

 

 

Appendix A: PCL support

29

 

= Supported

 

 

 

 

X = Not supported

 

Printer model

 

 

 

 

X651 MFP,

 

 

 

 

X652 MFP,

 

 

 

T650n/dn/dtn,

X654 MFP,

 

 

 

T652n/dn/dtn,

X656 MFP,

 

Command

Function

T654n/dn/dtn

X658 MFP

 

ESC%#B

Enter GL/2 Language

 

 

 

 

Note: The values of -1, 2, and 3 are not

 

 

 

 

supported by any of the printers

 

 

 

 

included in this document.

 

 

 

 

 

 

 

 

ESC% 12345X

Universal Exit Language (UEL) /

 

 

 

 

Start of PJL

 

 

 

 

 

 

 

GL/2 commands

= Supported

 

 

 

X = Not supported

 

Printer model

 

 

 

X651 MFP,

 

 

 

X652 MFP,

 

 

T650n/dn/dtn,

X654 MFP,

Command

Function

T652n/dn/dtn,

X656 MFP,

T654n/dn/dtn

X658 MFP

AA

Arc Absolute

 

 

AC

Anchor Corner

 

 

AD

Define Alternate Font

 

 

AR

Arc Relative

 

 

AT

Arc Absolute Three Point

 

 

BR

Bezier Relative

 

 

BZ

Bezier Absolute

 

 

CF

Character Fill

 

 

CI

Circle

 

 

CO

Comment

 

 

CP

Character Plot

 

 

CR

Color Range

 

 

DF

Default

 

 

Appendix A: PCL support

30

Loading...
+ 74 hidden pages