Lexmark LEXM05001 Users Manual

USER GUIDE for the PROXIMITY CARD READER (these instruction will be included in the host product
User Guide since the RF module will be preinstalled at the factory)

Your product may contain a built in dual interface card reader. The reader supports both contactless and
contact smart cards.
(tbd what types)

When the reader is working, the LED on the right is lighted green. Consult section (tbd) for troubleshooting.

For contact smart cards, insert the card with the contacts facing upwards into the reader. For contactless
operation, hold the card as close to the card reader slot as possible. The red LED on the right side of the
reader will come on indicating the reader is exchanging data with the card.

NOTICES:

Exposure to radio frequency radiation

The following notice is applicable if your product has an RFID Card Reader installed.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and
other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the
antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other
regulatory agencies.

Wireless device notices

In some environments, the use of wireless devices may be restricted. Such restrictions may apply aboard
airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy
that applies to the use of this device, ask for authorization to use it prior to turning it on.

Electronic emission notices

Federal Communications Commission (FCC) compliance information statement

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation. The FCC Class B limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your point of purchase or service representative for additional suggestions.

The manufacturer is not responsible for any radio or television interference caused by using other than
recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes
or modifications could void the user's authority to operate this equipment. To assure compliance with FCC
regulations on electromagnetic interference for a Class B computing device, use a properly shielded and
grounded cable such as Lexmark part number 1021294 for USB attach. Use of a substitute cable not properly
shielded and grounded may result in a violation of FCC regulations. Any questions regarding this compliance
information statement should be directed to:

Director of Lexmark Technology & Services
Lexmark International, Inc.

740 West New Circle Road
Lexington, KY 40550
[phone]

Industry Canada compliance statement

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Standard ICES-003.

Avis de conformité aux normes de l’industrie du Canada

Cet appareil numérique de classe B est conforme aux exigences de la norme canadienne relative aux
équipements pouvant causer des interférences NMB-003.

Industry Canada radio interference statement
Industry Canada (Canada)

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not
emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6,
obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb

.

The term "IC:" before the certification/registration number only signifies that the Industry Canada technical
specifications were met.

Industry Canada (Canada)

Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux
conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue,
y compris celles risquant d'altérer son fonctionnement.

Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de
manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population
par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web
de Santé Canada www.hc-sc.gc.ca/rpb

.

Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit

est conforme aux spécifications techniques d'Industry Canada.

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC,
2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States
relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain
voltage limits and on radio equipment and telecommunications terminal equipment.

Compliance is indicated by the CE marking.

A declaration of conformity with the requirements of the directives is available from the Director of
Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France.

This product satisfies the limits of EN 55022; safety requirements of EN 60950; radio spectrum requirements
of ETSI EN 300 330 and ETSI EN 302 291; and the EMC requirements of EN 55024, ETSI EN 301 489-1
and ETSI EN 301 489-3.

Others (tbd)