Lexmark 12EZ, 9EZ, 18EZ User Manual

HW

9EZ 12EZ 18EZ

GB

User manual and installation guide

HIGH WALL AIR CONDITIONER

GB

THANK YOU

Thank you for choosing this innovative Amcor air conditioner. We suggest that you
keep this manual in a safe place for future reference. It describes the many benefits
and advanced features this unique product has to offer. Before you use your new air
conditioner you should carefully read these instructions to maximise this product’s
performance.

For over 50 years Amcor has specialised in complete indoor environmental control,
manufacturing and marketing; dehumidifiers, portable air conditioners, coolers, air
purifiers, ionisers and aroma therapy scent diffusers. These world class products
incorporate the latest technological developments.

SAFETY INSTRUCTIONS

IMPORTANT!

• The indoor unit is designed for indoor operation only.

• Rating: This unit must be connected to a 220 – 240 V / 50 Hz earthed outlet.

• The installation must be in accordance with regulations of the country where the
unit is used.

If you are in any doubt about the electrical installation, have it checked and if
necessary modified by a qualified electrician.

• The air conditioner is safe. However, as with other electrical appliances, use it
with care.

• Keep the remote control out of the reach of children.

• Do not clean the air conditioner by spraying it or immersing it in water.

• Do not insert any object into the opening of the air conditioner.

• Disconnect it from the mains before cleaning the unit or any of its components.

• Never connect the unit to an electrical outlet using an extension cord. If an outlet
is not available, one should be installed by a licensed electrician.

WARNING

• Never operate this appliance if it has a damaged cord or plug. Do not lead the
cord over sharp edges.

• A damaged supply cord should be replaced by the manufacturer, its service agent
or a qualified person in order to avoid a hazard.

• Any service other than regular cleaning or filter replacement should be performed
by an authorized service representative. Failure to do so could result in a loss of
warranty.

If you have any difficulties in connecting the refrigeration circuit please refer
to a professional air conditioning engineer.

2

Do not use your air conditioner when:

GB

the power cord is
damaged.

HOW IT WORKS

The compressor (6) in the exterior unit
compresses the refrigerant into a high­temperature, high-pressure gas. When
this gas flows along the cooling fins of the
condenser (7), heat is extracted and the
gas condenses into a liquid, which is led
to the evaporator (1) in the interior unit.
The liquid expands into a gas at a low
temperature and low pressure.
This gas absorbs the warmth of the air
in the room, the cooled air is blown back
into the room and the heat absorbed
by the refrigerant gas is led to the
compressor.

A fan (3) draws the air (a) over the
filter (2) and evaporator (1) and blows the
cooled air (b) back into the room.
A fan (8) draws air over the condenser
and blows warm air (d) away.

there is a chance
of liquids falling on
the unit.

there is a risk of
interference from
foreign objects.

a

1. evaporator 5. liquid line

2. filter 6. compressor

3. fan 7. condenser coil

4. gas line 8. fan

it a close to a heat
source.

1

2

3

b

This air conditioner
is not made for DIY
repair.

4

c

7

6

5

d

8

Heating (H-models only)

The system operates in reverse: the condenser works as an evaporator, the
evaporator as a condenser: warm air is blown into the room. This is ideal for cool
days when the main heating is not on, or to supplement the main central heating in
autumn and spring.

Dehumidifying

As with cooling, the moisture in the air condenses on the cold evaporator at room
temperature and is drained outdoors.

3

GB

REMOTE CONTROL

7 4

8

9

10

LCD display:

temperature
timer setting
timer on/off
fan

16

2
3

fan speed
louvre setting

or indication of active mode or

selected option

5

Buttons:

1. Temperature setting

2. ON/OFF

3. Swing

4. Air flow

5. Sleep

6. Mode

7. Fan speed

8. Timer

9. Turbo

10. Hold

NB Clean and Lamp buttons are not applicable
to this air conditioner.

Using the remote control

The remote control signal has a range of up to 8 m. Point the
remote control at the receiver in the indoor unit.
A beep confirms that the remote control signal has been received.

Replacing the batteries

• remove the cover

• replace the AAA batteries, + to + and – to -–

• install the cover

• press the on/off button; if no symbols appear on
the display, the batteries are empty or have been
incorrectly installed

4

OPERATION

General

• Turn the unit on with the ON/OFF BUTTON [2]. The last used operating mode is

• The ON/OFF BUTTON turns the appliance off; the operating mode active at this

• Set the temperature with the TEMP BUTTONS [1] – within the limits of the

• Use the FAN SPEED BUTTON [7] to set the fan speed at low , medium , high or

• Use the SWING BUTTON [3] to adjust the horizontal (up/down) air flow direction.

Mode selection

Press the MODE BUTTON [6] to select the operating mode. The symbol on the left
side of the display indicates the selected mode.

Auto

1. Press the MODE BUTTON [6] until the symbol appears next to AUTO.

2. The temperature is automatically set to 25 °C and can not be adjusted.

3. Use the FAN SPEED BUTTON [7] to set the fan speed.

4. Use the SWING BUTTON [3] to adjust the air flow direction.

GB

selected.

moment is stored in memory and will be used when the air conditioner is
switched back on again.

thermostat: 18 °C – 32 °C. Each press of the button makes a change of 1 °C.

automatic ( is flashing). The fan speed in the automatic setting is determined
by the difference between the set temperature and the room temperature.

Cool

1. Press the

MODE BUTTON [6] until the symbol appears next to COOL.

2. Set the desired temperature.

3. Use the FAN SPEED BUTTON [7] to set the fan speed.

4. Use the SWING BUTTON [3] to adjust the air flow direction.

Dry (dehumidify)

1. Press the

MODE BUTTON [6] until the symbol appears next to DRY.

2. The temperature is automatically set to 25 °C and can not be adjusted.

3. The fan speed is automatically set to low and can not be changed.

4. The air flow direction is automatically set to fixed and can not be adjusted.

Heat

1. Press the MODE BUTTON [6] until the symbol appears next to HEAT.

2. Set the desired temperature.

3. Use the FAN SPEED BUTTON [7] to set the fan speed.

4. Use the SWING BUTTON [3] to adjust the air flow direction.

5

GB

Fan mode

1. Press the MODE BUTTON [6] until the symbol appears next to FAN.

2. Use the FAN SPEED BUTTON [7] to set the fan speed.

3. Use the SWING BUTTON [3] and the AIR FLOW BUTTON [4] to adjust the air flow direction.

Sleep button

Press the
next to

SLEEP BUTTON [5], the symbol appears on the right hand side of the display

SLEEP. Press again to release the sleep mode.

In this mode the air flow sound is reduced. Use the sleep mode when you are going
to bed.
In

COOL mode operation, the room temperature will be raised gradually 2 °C higher

than the setting when SLEEP mode was activated.
In HEAT mode operation, the room temperature will be lowered gradually 5 °C lower
than the setting when SLEEP mode was activated.
When the SLEEP MODE is selected, the display on the unit will dim to be seen well in a
dark room without causing distraction to sleep.

Turbo button

During COOL or HEAT mode operation, the air flow rate (the amount of air circulating
through the room) can be increased. Press the TURBO BUTTON [9], the symbol
appears on the right hand side of the display next to TURBO. Press this button again
to cancel the turbo operation and return to the other air flow rates.

Timer button (timed switching off )

1.

Press the TIMER BUTTON [8] to enter the “timed” mode when the unit is switched on.

2. Press this button to set after how many hours the air conditioner should switch
off. The symbol in the display cycles through 1 2 ... 24 cancel (no
indication) 1... with each press of the button.

Once the set time has elapsed (the symbol shows the remaining number of
hours) the air conditioner will switch itself off. To cancel this function before the set
time has elapsed, press the TIMER BUTTON [8] again.

Timer button (timed switching on)

The air conditioner is switched off (stand-by).

1. Press the TIMER BUTTON [8] to enter the “timed” mode.

2. Press this button to set after how many hours the air conditioner should switch
on. The symbol in the display cycles through 1 2 ... 24 cancel (no
indication) 1... with each press of the button.

3. Set the desired operation, temperature, fan speed, etc.

Once the set time has elapsed (the symbol shows the remaining number of
hours) the air conditioner will switch itself on. To cancel this function before the set
time has elapsed, press the

TIMER BUTTON [8] again.

Hold button

6

GB

Press the

HOLD BUTTON [10] to lock or to unlock the keys of the remote control. The

symbol on the right hand side of the display next to HOLD indicates locked keys.

Left/right air flow direction

Method 1: Manually adjust
Turn the air conditioner off. Adjust the fins by hand.

Method 2: Horizontal and vertical auto swing
Press the

AIR FLOW BUTTON [4] to let the fins swing constantly or leave them in a fixed

manual set postion.

IMPORTANT

Auto restart

The air conditioner will automatic restart when electricity is restored after a power
cut. If in doubt, check the settings.

Range of internal thermostat

The internal thermostat can be set at a desired temperature between 16 and 32 °C.
Note that whether the desired value is achieved depends on conditions in the room.

Range of heat pump function

The heat function can be used to supply low cost heat when the external
temperature is approximately 10 °C or higher.

Note that it may not operate properly at lower external temperatures, it will cycle
frequently to defrost the outdoor coil and stops operating at minus 5 °C.

Capacity

The required cooling or heating capacity depends greatly on the location and/or use
of the room where the air conditioner is installed. Strong sunlight and the presence
of people, lights or equipment create an additional heat load with resulting smaller
reduction in room temperature.
Normal living spaces require about 100 W per square metre of floor surface. In
strong sunlight or if other sources of heat are present, this may be as much as
350 W/m2.

Tip: on warm days, let the air conditioner cool the room as much as possible during
the night. Cold walls and furniture will help to keep the room pleasant during use.
Avoid strong sunlight.
Aim for a room temperature only up to 3–5 °C lower than ambient temperature to
save energy and shock to the body when moving out of the conditioned space. The
air conditioner will dry the air, making it more comfortable even if not very cold.

7

GB

Emergency start

In the event of a problem, or when the remote control is missing,
the air conditioner can be operated using the emergency button
under the panel in the indoor unit. Open the front panel and press
the button to switch on (in the mode last set) or to switch off.

FILTERS

Turn the air conditioner off and remove the plug from the mains outlet.

A

Opening: at the A recesses, pull the

front part up. The front part will stay
horizontal (turn up 90 °).

1. Hold the front part open (or put it in horizontal position) and remove the
filter(s).

2. Tap the filter gently or use a vacuum cleaner to remove dirt. If the dust filter
is very dirty, it may be washed in lukewarm water with a very small amount of
neutral detergent. Rinse well and allow to dry completely (not in direct sunlight or
near a source of heat).

3. Keep the grid panel open and reinstall the filter(s). Press the panel shut; a click
indicates it is closed properly.

4. Plug the appliance back in and turn it on.

A

B B

Closing: press the front part down at

the sides at B and in the middle at C.
Make sure it is properly closed (click).

C

8

CLEANING

Turn the air conditioner off and remove the plug from the mains outlet.

Indoor unit

Dust regularly with a dry cloth or slightly damp paper towel.
Never use chemicals or solvents. Never spray a liquid in or over the appliance.

Outdoor unit

Remove dirt and keep the air intake and exhaust openings free of leaves, etc.
Cleaning with chemicals may cause damage.

END OF PERIOD OF USE

If the air conditioner is not going to be used for an extended period:

• set in fan mode with temperature set at 30 °C (86 °F) so that the inside of the
appliance dries out.

• remove the plug from the outlet (even when switched off the air conditioner will
consume about 5 W) and take the batteries out the remote control.

• clean the indoor and outdoor unit.

• clean the filters as well.

GB

START OF PERIOD OF USE

If the air conditioner is to be used again after an extended period:

• check that the air intake and exhaust openings of the indoor and outdoor unit are
not blocked. Remove all dirt and obstacles.

• check that there is a filter.

• check that the condensation outlet drains properly.

• install 2 AAA batteries in the remote control.

• dust the indoor unit.

• turn the appliance on, set the time and desired setting.

Note: make sure condensation is drained freely and that there is no obstacle such
as algae growth, otherwise leaks may occur.

9

GB

.BOZXJOEPXT
.VDITVOTIJOF
4PVUIGBDJOH

-FTTXJOEPXT

-FTTTVOTIJOF

/PSUIGBDJOH

INSTALLATION GUIDE

8IJDISPPNJTCFTUTVJUFEGPSUIF"JS$POEJUJPOFS

8N

8N





4J[FPGUIFSPPN
GMPPSBSFB



N



N



N



N

$PPMJOHDBQBDJUZ

"TVJUBCMFSPPNEFQFOETPOUIFDPPMJOHDBQBDJUZTVOMPDBUJPOXJOEPXBSFBQSFTFODFPG
IFBUTPVSDFTMBNQTBQQMJBODFTOVNCFSPGQFPQMFFUD5BLFUIJTJOUPBDDPVOU
3VMFPGUIVNCJOBWFSBHFTVOTIJOFDPOEJUJPOTBOEOPQSFTFODFPGPUIFSIFBUTPVSDFT
8QFSTRVBSFNFUSFUIVTBDPPMJOHDBQBDJUZPG8JTCFTUQMBDFEJOBN

8 8 88 8



SPPN

In case of a non quick coupling unit, make sure to have the professional after-sales
service person or authorized dealer to install the units.

• The units may not be installed in places where there might be leakage of
combustible gases: fire hazard.

• Make sure that an earth leakage circuit breaker is installed,
either as a plug in device or on the main board, instead of a
fuse.

• Check whether the connection of wires between indoor and
outdoor unit is not loose.

• Make sure that the air conditioner is properly grounded.

10

SAFETY ASPECTS

Check the network voltage.

Make sure that the existing network voltage corresponds to the value specified on
the type tag on the appliance.

Keep the work area tidy.

Carelessness in the work area can lead to accidents.

Use the right tools.

Do not use tools that are not sturdy enough for heavy work. Use reliable tools
suitable for the purpose for which they are intended.

Wear a mask and eye and ear protection.

When doing work which may produce splinters or dust and when working over your
head always wear eye protection and a well-fitting face mask. Wear ear mufflers in
noisy conditions.

Extension cord when working outdoors.

Only use approved and correspondingly marked extension leads and sockets during
work out of doors.

Check electrical equipment for any damage.

Never use equipment with a switch that does not work.

GB

Be careful when working on steps, ladders and scaffolding.

Be extra careful when working on an elevated surface. Make sure that stepladders,
steps, ladders and scaffolding are placed correctly and cannot slip.

Electrical cables, gas and water pipes etc.

Important safety aspect for work with drilling equipment:
Make sure that when drilling you cannot strike electrical cable, gas or water pipes.

Check the wall with a duct/cable detector before you start drilling.

Is everything clear?

Once you have familiarised yourself with the safety recommendations and have
learnt from the user’s manual how to use the tools, you can start working. By
following the instructions and recommendations of the manufacturers you can be
sure that you are working as safely as possible.

Keep these guidelines!

11

GB

SAFETY

Read the section on safety aspects and these instructions before you start.
Stick to the work sequence and working method shown here.

For technical or commercial reasons, the manufacturer may make changes to the
appliance or component parts, without general notification. You can consult your
supplier about this.

IMPORTANT:

• This appliance must be connected to an earthed socket for 230 V/50 Hz, with a
13 A fuse.

• The connection to the national grid must be carried out in agreement with the
safety standards as regards the installation of electrical household appliances
applicable in the country of use.

If in doubt have the electrical installation checked and if necessary modified by a
qualified electrician

Ensure you have:

• a well lit and a work area clear of clutter.

• a well thought out and pre-arranged work plan.

• sound tools and reliable implements.

• protection: safety goggles, ear protection, mask, hard hat, work shoes and work
gloves.

The outdoor unit must be lifted and put in place by two people.

POSITION OF THE INDOOR UNIT

Install the indoor unit where there is:

• no influence from outdoor air,

• no blockage of air inlet or air outlet,

• no smoke or steam, and no generation, inflow, lingering or leakage of flammable
gases,

• no high-frequency facility (such as arc welder).

Avoid places where acid solutions or some special sprayers (sulfides) are frequently
used.

• The air from the indoor unit should reach every corner of the room.

• Do not install a fire alarming device near the air outlet, the alarm may
erroneously be triggered by the warm air from the unit.

12

Ceiling

At least 10 cm

GB

For operational convenience and
for safety, ensure there is enough

At least
15 cm

space between the unit and
walls, windows and ceiling.

Wall-mounting plate

Pipe lines can be connected in
the directions 1, 2, 3, 4 or 5 as indicated in Figure 3.
When connection 3, 4 or 5 is chosen, a groove for
the pipes has to be opened on the base stand.

Installation of the wall-mounting plate

Fix the wall-mounting plate firmly on the wall with
screws. Make sure the plate is level. A slanted
wall-mounting plate may jeopardize the smooth
discharge of the condensed water and cause the
indoor unit to leak.

Drill hole in the wall

Drill a hole slightly below the wall-mounting plate,
with a diameter of 65 mm and the outdoor edge
of the hole 5–10 mm lower (Figure 4) so that the
condensed water can smoothly flow out.
Cut the wall penetrating pipe to proper length
according to the thickness of the wall (i.e. 3–5 mm
longer than the wall thickness) and insert the pipe
as shown in Figure 4.

At least
15 cm

At least 230 cm

Floor

Installation of the drain pipe

Install the pipelines of the indoor unit in
accordance with the direction of the wall holes.
Wrap the drain pipe and the pipelines tightly with
tape. Make sure that the drain pipe is underneath
the pipelines (Figure 5).

Installation of the indoor unit

Pass the connection wires, connecting pipelines and drain pipe through the wall
hole. Hang the indoor unit on the hooks at the top of the wall-mounting plate
so that the hooks at the bottom of the indoor unit match the hooks of the wall­mounting plate (Figure 6).

13

GB

Inspections:

• See if the hooks at the top and bottom are firmly fixed.

• See if the position of the master unit is properly levelled.

• The drain pipe must not curve upward (Figure).

• The drain pipe must be at the lower part of the

Connecting
wires

wall pipes (Figure) to avoid possible restriction
to the water flow.

Drain pipe

POSITION OF THE OUTDOOR UNIT

• where the support can stand the load of the units weight and not cause
vibrations and noises

• where it is not exposed to rain or direct sunshine, but has good ventilation, no
restriction to the air flow

• where noises will not affect neighbouring places

• away from areas where generation, ingress, stagnant or leakage of inflammable
gases might occur.

Do not install on a non-metal frame.
Pay attention to the drainage of condensed water from the base plate during
operation. Avoid possible puddles or flow over surfaces which may become slippery
and a hazard to others.
Avoid the air outlet being directly against the wind.

Connecting pipe

Wall pipe

Drain pipe

Space requirements around the outdoor unit

At least
200 mm

At least 500 mm

At least
200 mm

14

At least
200 mm

At least
300 mm

At least 200 mm

At least
1000 mm

At least
200 mm

At least
500 mm

At least

At least 500 mm
Space for
maintenance

1000 mm

• use expansion bolts to fix the mounting supports on the wall

c

• use bolts and nuts to fix the outdoor unit firmly on the supports and keep on the
same level

• if the unit is installed on the wall or at the roof top, the supports have to be firmly
fixed to resist earthquake or strong wind.

PIPELINES CONNECTION

Ordinary pipeline connection (suitable for non-quick coupler)

No dust, foreign objects, air or moisture should be allowed to enter the air
conditioning system. Careful attention should be paid when the pipeline connection
for the outdoor unit is made. Avoid (repeated) curves as much as possible,
otherwise hardening or cracks might be caused to the pipes. Suitable wrenches
should be used when the pipeline connection is done to ensure appropriate torque.
Excessive torque might damage the joints while too little torque might lead to
leakage.
For pipes vacuuming, see “Exhaust air” paragraph.

Diameter of the copper pipe Tightening torque

[“] / [mm] [kgf*m] [Lbs/feet]
1/4” / 6.35 mm 1.6 11.6
3/8” / 9.52 mm 3.0 21.7

Nut of
connecting pipe

GB

Torque wrench

Spanner

Joint

Connect the indoor connections (suitable for quick coupler)

Be aware that it is possible to connect the connectors only in one way. Follow the
procedure below:
a. Remove the 4 dust caps from indoor connectors

(unit and pipes).

b. Align the joint counter to the connecting pipe

with the proper joint, tighten the connecting nuts
manually. Then, make it secure with a wrench

Quick coupler

(wrapping with insulating

Low pressure valve

Valve core cap

High pressure valve

applying torque as shown in the table. If a torque
meter is not available, secure the connector with
1 turn after manual secure.

c. Connect the drain hose to the indoor drain outlet. Wrap the drain tube with the

refrigerant tubes tightly with tape. Make sure that the drain pipe is underneath
the pipelines.

d. Connect the electric plugs, and place it above tubing in the back side of the unit.

15

GB

EXHAUST AIR

Only applicable for non-quick coupler.

R410A: use pump vacuum to exhaust the air.
This procedure must be performed by a professional.

multiple gauge

pressure

vacual mercury column

main regulation
valve closed

to outdoor unit
industrial pipe

refrigerant charging diagram

POWER CABLE CONNECTION

1. Remove the cover from the outdoor unit.

2. Non-quick coupler:

connect the indoor power and control wires firmly with
the ones in the outdoor unit as shown in

Figure 11 - top.

Quick coupler:

directly connect the quick cable coupler from the indoor
unit with the one from the outdoor unit (Figure 11
– bottom).

3. Use a pressing plate to fix the wires firmly and replace
the cover.

Note: Incorrectly connected wires may lead to electric malfunction and can
damage the units. See safety instructions on pages 2 and 12 for electric installation
compliance and damaged cable.

Figure 11

high pressure
side gauge

hand regulation

valve closed
from high pressure side
maintenance point

R407C/R410A
container (brown)

wire pressing
plate

Drawer

Screw

FINISHING TOUCHES

• Use a thermal tube to wrap the joints and wrap the tube tightly with ethylene
tape.

• Fix the wrapped pipelines vertically on the external wall with
duct through and pipe clamps, available at DIY-stores.

Fill the gaps in the holes made for the pipeline to prevent

rain-water from entering.

• Lead the water drainage pipe to a suitable drainage point,
making sure that the water can flow through freely.

16

PARTS

GB

Indoor unit

Air flow direction
adjusting

Air outlet

Drain tube

Air filter

Room temperature
detecting probe

Emergency
start/stop

RUN

Electric connection

• •

TIMER

Air inlet
side and rear

Outdoor unit

Refrigerant piping
connection

Air discharge

17

GB

TECHNICAL DATA

Model HW-9EZ HW-12EZ HW-18EZ

Cooling capacity

measured conform EN 14511

Heating capacity

Power supply 220 – 240 V • 50 Hz • 1Ph
Power consumption W 840/780 1100/1000 1600/1580
Current A 3.9/3.7 5.06/4.7 7.27/7.4
Dehumidification – max. L/24h 17 24 31
Air flow – at high fan speed m
Refrigerant R410A
Refrigerant load g 760 1080 1500
Room size – up to m
Fan speeds 3
Thermostat °C 16 – 32
Timer h 1 – 12
Dimensions (W x D x H)

– indoor unit
– outdoor unit

Weight
– indoor unit
– outdoor unit

Subject to modifications without prior notice. Please refer to the rating label for greater precision.

BTU/h 9200 12000 16500

kW 2.7 3.51 4.82

BTU/h 9500 12300 17400

kW 2.8 3.6 5.1

3

/h 500 600 729

2

mm

kg

27 35 47

790 x 180 x 270
700 x 225 x 500

9

27

790 x 180 x 270

795 x 255 x 540

10.5
36

940 x 180 x 270
850 x 295 x 605

14
45

18

ELECTRIC CONNECTION (UK ONLY)

For your safety please read the following information.

Warning: This appliance must be earthed.

The appliance must be connected to a 220-240 volts 50 cycle AC supply by means of a three pin socket,
suitably earthed and should be protected by a 13 amp fuse in the plug.

The appliance is supplied with a moulded 13 amp 3 pin mains plug fitted with a 13 amp fuse. Should the
fuse require replacement, it must be replaced with a fuse rated at 13 amp and approved to BS1362.

The plug contains a removable fuse cover that must be refitted when the fuse is replaced. In the event
of the fuse cover being lost or damaged, the plug must not be used until a replacement cover has been
obtained.

If the moulded mains plug is unsuitable for the socket outlet in your home or is removed for any other
reason, then the fuse should be removed and the cut off plug disposed of safely to prevent the hazard of
electric shock.

There is a danger of electric shock if the cut off plug is inserted into any 13 amp socket outlet.

How to wire a 13 amp plug.

Important

The wires in the mains lead on this appliance are coloured in
accordance with the following code:
Green and Yellow – Earth
Blue – Neutral
Brown – Live
The green and yellow wire must be connected to the terminal
in the plug which is marked with the letter E or with the earth
symbol
The blue wire must be connected to the terminal marked N
The brown wire must be connected to the terminal marked L.

.

GB

19

Hong Kong

Amcor Ltd
Suite 1010–1011, 10/F, Ocean Centre,
Harbour City, 5 Canton Road,
Tsim Sha Tsui, Kowloon,
Hong Kong
Tel: [phone]
Fax: [phone]
Email: [e-mail]

United Kingdom

Amcor Ltd
9 Ryan Drive, West Cross Centre,
Great West Road, Brentford,
Middlesex, TW8 9ER,
United Kingdom
Tel: [phone]
Fax: [phone]
Email: [e-mail]

USA

Amcor Inc.
685A Gotham Parkway, Carlstadt,
New Jersey 07072,
United States of America
Tel: [phone]
Fax: [phone]
Email: [e-mail]

The Netherlands

Amcor B.V.
Anton Philipsweg 9-11,
1422 AL Uithoorn,
The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Israel

Amcor International Ltd
1 Sapir St.,
P.O. Box 12001,
Hertzelia Pituach,
Israel
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Singapore

Amcor Investments (Singapore) Pte Ltd
545 Orchard Road,
#13-02, Far East Shopping Centre,
Singapore 238882
Tel: [phone]
Fax: [phone]
Email: [e-mail]

China

Shan Xia Industrial Development Zone,
Heng Li Town, Dongguan City,
Guangdong Province, China

Plant One - Amcor (China) Ltd

Tel: [phone]
Fax: [phone]
Email: [e-mail]

Plant Two - Amcor Appliances Ltd

Tel: [phone]
Fax: [phone]
Email: [e-mail]

HW-EZ 913126320