Lex 3I380D-D90, 3I380D Series, 3I380D-I12 User Manual

3I380D

Intel Bay Trail-I E3815 (Single Core) /

Intel Bay Trail-D J1900 (Quad Core) CPU, On Board /

Socket DDR3L, 4 x Intel I211AT LAN / USB / VGA / HDMI

All-In-One

Intel Bay Trail-I E3815 1.46 GHz / Intel Bay Trail-D

VGA, HDMI, COM, PCIe mini card

Multi-LAN Board , SATA, USB

NO. 3I380D_V0.1
Release date: Nov. 21. 2014

J1900 2.0GHz

Contents

3I380D

Warning!...................................................................................................................................

Hardware Notice Guide ......................................................................................................

CHAPTER 1 GENERAL INFORMATION .................................................................................

1-1 MAJOR FEATURE................................................................................................................

1-2 SPECIFICATION ..................................................................................................................

1-3 INSTALLING THE SO-DIMM (FOR 3I380D-D90) .................................................................

1-3-1.1 REMOVING THE SO-DIMM (FOR 3I380D-D90) ............................................................

1-4 DIRECTIONS FOR INSTALLING THE MINI CARD .............................................................

1-5 PACKING LIST (FOR 3I380D-D90) ......................................................................................

1-5-1 PACKING LIST (FOR 3I380D-I12) ....................................................................................

CHAPTER 2 HARDWARE INSTALLATION ............................................................................

2-1 UNPACKING PRECAUTION ................................................................................................

2-2 UNPACKING CHECKUP ......................................................................................................

2-3 DIMENSION (3I380D) ..........................................................................................................

2-4 LAYOUT (3I380D) ................................................................................................................

2-5 DIAGRAM (3I380D-D90) ......................................................................................................

2-5-1 BOTTOM SIDE DIAGRAM (3I380D-D90) .........................................................................

2-5-2 DIAGRAM (3I380D-I12) ....................................................................................................

2-5-3 BOTTOM SIDE DIAGRAM (3I380D-I12) ...........................................................................

2-6 INSTALL MEMORY ..............................................................................................................

2-7 LIST OF JUMPERS ..............................................................................................................

2-8 JUMPER SETTING DESCRIPTION .....................................................................................

2-9 COMS DATA CLEAR ............................................................................................................

2-10 JSC2: COM2 RS422/RS485 SELECT (OPTION) ...............................................................

CHAPTER 3 CONNECTION ..................................................................................................

3-1 LIST OF CONNECTORS.......................................................................................................

3-2 DC POWER INPUT ..............................................................................................................

3-3 BATTERY INPUT ..................................................................................................................

3-4 DC POWER OUTPUT ..........................................................................................................

3-5 FRONT PANEL & FAN ..........................................................................................................

3-6 DISPLAY INTERFACE .........................................................................................................

3-7 AUDIO INTERFACE (OPTION) ............................................................................................

3-8 I/O INTERFACE ....................................................................................................................

3-9 DIGITAL INPUT / OUTPUT (OPTION) ..................................................................................

2

3-10 I C Bus Interface .................................................................................................................

3-11 PS2 KB/MS (OPTION) ........................................................................................................

3-12 LAN INTERFACE ...............................................................................................................

3-13 USB INTERFACE ..............................................................................................................

1

2

4

5

6

7

9

10

11

12

13

13

14

15

16

17

18

19

20

21

22

22

23

24

25

25

26

27

27

28

29

30

30

32

33

33

33

34

i

3-14 SATA INTERFACE .......................................................................................................................

3-15 MICROSD CARD INTERFACE (SOCKET PUSH-PUSH) (OPTION) ..........................................

3-16 MODULE SOCKET ......................................................................................................................

3-17 SIM SOCKET ...............................................................................................................................

3-18 SODIMM SOCKET (OPTION) .....................................................................................................

3-19 CONNECTOR WAFER OF COMPATIBLE BRAND AND PART NUMBER LIST .........................

CHAPTER 4 INTRODUCTION OF BIOS ..........................................................................................

4-1 ENTER SETUP ..............................................................................................................................

4-2 BIOS MENU SCREEN & FUNCTION KEYS .................................................................................

4-3 GENERAL HELP ...........................................................................................................................

4-4 MENU BARS .................................................................................................................................

4-5 MAIN ..............................................................................................................................................

4-6 ADVANCED ...................................................................................................................................

4-6-1 BOOT CONFIGURATION ...........................................................................................................

4-6-2 PCI EXPRESS CONFIGURATION .............................................................................................

4-6-2-1 PCI EXPRESS ROOT PORT 1/2/3/4 ......................................................................................

4-6-2-2 PCIE PORT 1/2/3/4 SPEED ....................................................................................................

4-6-2-3 PCIE PORT 1/2/3/4 OPTION ROM .........................................................................................

4-6-3 USB CONFIGURATION .............................................................................................................

4-6-4 VIDEO CONFIGURATION ..........................................................................................................

4-6-5 THERMAL CONFIGURATION ....................................................................................................

4-6-6 SATA CONFIGURATION ............................................................................................................

4-6-7 CONSOLE REDIRECTION ........................................................................................................

4-6-8 ACPI TABLE / FETURES CONTROL .........................................................................................

4-7 SECURITY .....................................................................................................................................

4-8 POWER .........................................................................................................................................

4-9 BOOT .............................................................................................................................................

4-9-1 LEGACY .....................................................................................................................................

4-10 EXIT .............................................................................................................................................

4-11 DEVICE MANAGER .....................................................................................................................

4-11-1 SIO FINTEK8180U ...................................................................................................................

CHAPTER 5 DRIVER INSTALLATION ............................................................................................

5-1 INF INSTALL INTEL BAYTRAIL CHIPSET DRIVER (EXAMPLE FOR WIN8 64BIT) ....................

5-2 VGA INSTALL INTEL BAYTRAIL VGA DRIVER (EXAMPLE FOR WIN8 64BIT) ...........................

5-3 SERIAL IO INSTALL DRIVER BAYTRAIL SERIAL IO DRIVER (FOR WINDOWS 7 ONLY) ..........

5-4 XHCI INSTALL INTEL USB 3.0 XHCI DRIVER (FOR WINDOWS 7 ONLY) ..................................

5-5 HD AUDIO INSTALL HIGH DEFINITION AUDIO DRIVER (EXAMPLE FOR WIN 64BIT) .............

5-6 MBI INSTALL INTEL MBI DRIVER (FOR WIN 8/8.1 ONLY) ..........................................................

5-7 TXE LNSTALL INTEL TXE DRIVER ...............................................................................................

5-7-1 TXE INSTALL FOR WIN8/WIN8.1 ..............................................................................................

5-7-2 TXE INSTALL FOR WIN7 ...........................................................................................................

36

36

37

38

38

39

40

40

41

42

42

43

44

45

46

47

48

49

50

51

53

54

55

56

57

58

59

60

62

63

64

66

68

70

72

74

76

77

79

79

81

ii

5-8 HOW TO UPDATE AMI BIOS .........................................................................................................

APPENDIX A:POWER CONSUMPTION TEST ..................................................................................

APPENDIX B:RESOLUTION LIST .......................................................................................................

APPENDIX C: F75111N I C DIO DECICE ............................................................................................

1-1 IO DEVICE : F75111 UNDER WINDOWS .....................................................................................

1-2 IO DEVICE : F75111 VB6 UNDER WINDOWS .............................................................................

1-3 IO DEVICE : F75111 UNDER LINUX .............................................................................................

2

83

84

86

87

87

90

92

iii

Copyright

This manual is copyrighted and all rights are reserved. It does not allow any non
authorization in copied, photocopied, translated or reproduced to any electronic or
machine readable form in whole or in part without prior written consent from the
manufacturer.

In general, the manufacturer will not be liable for any direct, indirect, special, incidental
or consequential damages arising from the use of inability to use the product or
documentation, even if advised of the possibility of such damages.

The manufacturer keeps the rights in the subject to change the contents of this
manual without prior notices in order to improve the function design, performance,
quality, and reliability. The author assumes no responsibility for any errors or omissions,
which may appear in this manual, nor does it make a commitment to update the
information contained herein.

Trademarks

Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
All other trademarks, products and or product's name mentioned here are for
identifi cation purposes only, and may be trademarks and/or registered trademarks
of their respective companies or owners.

© Copyright 2014
All Rights Reserved.
User Manual edition 0.1, Apr. 22. 2014

1. Battery
Batteries on board are consumables.

The life time of them are not guaranteed.

2. Fless solution with HDD
The specifi cation & limitation of HDD should be considered carefully when

the fanless solution is implemented.

3. We will not give further notifi cation in case of changes of

product information and manual.

4. SATA interface does not support Hot SWAP function.

5. There might be a 20% inaccuracy of WDT at room temperature.

6. Please make sure the voltage specifi cation meets the requirement

of equipment before plugging in.

7. There are two types of SSD, commercial grade and industrial grade, which

provide different read/write speed performance, operation temperature and
life cycle. Please contact sales for further information before making orders.

8. Caution! Please notice that the heat dissipation problem could cause the MB

system unstable. Please deal with heat dissipation properly when
buying single MB set.

Warning !

9. Please avoid approaching the heat sink area to prevent users from

being scalded with fanless products.

10. If users repair, modify or destroy any component of product unauthorizedly,
We will not take responsibility or provide warranty anymore.

11. DO NOT apply any other material which may reduce cooling

performance onto the thermal pad.

12. It is important to install a system fan toward the CPU to decrease

the possibility of overheating / system hanging up issues,
or customer is suggested to have a fi ne cooling system to dissipate heat
from CPU.

1

Hardware Notice Guide

*

1. Before linking power supply with the motherboard, please attach DC-in adapter to
the motherboard fi rst. Then plug the adapter power to AC outlet.
Always shut down the computer normally before you move the system unit or
remove the power supply from the motherboard. Please unplug the DC-in adapter fi rst
and then unplug the adapter from the AC outlet.
Please refer photo 1 as standard procedures.

2. In case of using DIRECT DC-in (without adapter), please check the allowed range
for voltage & current of cables. And make sure you have the safety protection for
outer issues such as short/broken circuit, overvoltage, surge, lightning strike.

3. In case of using DC-out to an external device, please make sure its voltage and
current comply with the motherboard specifi cation.

4. The total power consumption is determined by various conditions
(CPU/motherboard type, device, application, etc.). Be cautious to the power cable
you use for the system, one with UL standard will be highly recommended.

5. It’s highly possible to burn out the CPU if you change/ modify any parts of
the CPU cooler.

6. Please wear wrist strap and attach it to a metal part of the system unit
before handling a component. You can also touch an object which is
ground connected or attached with metal surface if you don't have wrist strap.

7. Please be careful to handle & don't touch the sharp-pointed components on
the bottom of PCBA.

8. Remove or change any components form the motherboard will VOID the warranty of
the motherboard.

9. Before you install/remove any components or even make any jumper setting
on the motherboard, please make sure to disconnect the power supply fi rst.
(follow the aforementioned instruction guide)

10. "POWERON after PWR-Fair” function must be used carefully as below:
When the DC power adaptor runs out of power, unplug it from the DC current;
Once power returns, plug it back after 5 seconds.
If there is a power outage, unplug it from the AC current, once power returns,
plug it back after 30 seconds. Otherwise it will cause system locked or made
a severe damage.

Remark 1:
Always insert/unplug the DC-in horizontally & directly to/from the motherboard.
DO NOT twist, it is designed to fi t snugly.
Moreover, erratic pull / push action might cause an unpredictable damage to the
component & system unit.

2

Photo 1 Insert

1

2

3

Unplug

3

2

1

3

Chapter-1

General Information

The 3I380D is built to be an all-in-one networking control board. It’s designed to combines
all necessary input and output interfaces, which make them to be ideal control board for
thin client, fi rewall or server applications. 3I380D is the perfect platforms for whole range
of small form factor, low-power devices.

High-performance and power-efficient networking platform, the embedded motherboard
3I380D is specially designed for advanced embedded VPN or fi rewall applications where
the economical use of power is in high demand. With the sizable memory bandwidth of on
board 2GB DDR3L or DDR3L SODIMM socket or the fl exibility of expanding the memory
to 4GB DDR3L SODIMM socket, 3I380D ensures the high performance level required of
today's most popular fi rewall applications. 3I380D supports with four 10/100/1000 Mbps
Ethernet for seamless broadband connectivity. With Wake-On LAN function and the PXE
function in BIOS, these are perfect control board for networking devices. The built-in LAN
option includes four Intel I211AT LAN chipset for PCIe x 1 V2.1 interface with RJ45 for
10/100/1000 Mbps Ethernet. 3I380D also offers two COM ports (by wafer connection) to
meet the needs of COM port connectivity.

3I380D integrates PCIe mini card for mSATA & USB & SIM card interfaces. In addition,
with EHCI high-speed host controller interface; it ensures the high performance level and
also the powerful and fl exible expansion. Moreover, a single fl ash chip holds the system
BIOS, and you can change the fl ash BIOS by the Utility Update.

The 3I380D all-in-one motherboard is fully compatible with industrial standards, plus
technical enhancements and thousands of software applications developed for IBM PC/
AT compatible computers. The control logic provides high-speed performance for the most
advanced multi user and multitasking applications available today.

4

1-1 Major Feature

1. Intel Bay Trail-I E3815 1.46GHz / Intel Bay Trail-D J1900 2.0/2.42(Burst)GHz SOC

2. Intel Bay Trail-I Integrated Graphics chipset:

Bay Trail-I E3815 Graphics speed: 400MHz

Bay Trail-D J1900 Graphics speed: 688MHz/854MHz(Turbo)

3. 1 x DDR3L SO-DIMM socket or On board DDR3L SDRAM (max. 4GB)

4. On board SSD 4/8/16/32 GB (option)

5. Support 4 x 10/100/1000 Mbps LAN on Board

(Intel I211AT LAN chipset for PCIe x 1 V2.1 interface)

6. Support 1 pair LAN Bypass function when DC Power off (option)

7. Support 1 x SATA, 7 x USB

8. Support PCIe mini cards including one for USB & SIM card interfaces,

another one for USB & mSATA interface

9. On board DC +12V Power Supply (Note: -5V, -12V no support)

10. Compact PCB Dimension: 145 x 102 mm (3.5 inch)

11. One 3G SIM card reader (for 3G mini card use)

5

1-2 Specifi cation

1. SOC : Intel Bay Trail-I E3815 1.46GHz (Single core) /

Intel Bay Trail-D J1900 2.0/2.42(Burst)GHz (Quad core)

2. Memory : 1 x DDR3L SO-DIMM socket or On board DDR3L SDRAM (max. 4GB)

3. VGA : Intel Bay Trail-I Integrated Graphics chipset:

Bay Trail-I E3815 Graphics speed: 400MHz

Bay Trail-D J1900 Graphics speed: 688MHz/854MHz(Turbo)

4. I/O Chip : F81801U I/O chipset

5. SATA : One SATA port with independent DMA operation supported

6. NAND fl ash memory: On board SSD 4/8/16/32 GB (option)

7. LAN : 4 x Intel I211AT LAN chipset or Intel I210AT LAN chipset (option)

with 10/100/1000 Mbps for PCIe x 1 V2.1 interface

8. Serial Port : 2 x COM

9. USB : 6 x USB 2.0 (3 external + 3 internal) & 1 x USB 2.0/3.0 (internal)

10. Sound (option) : ALC886 HD Audio Specifi cation 1.0 Two channel sound

11. LAN Bypass (option) : support 100Mb LAN Bypass function when DC Power off

12. DIO (option) : Fintek F75111N chipset for 4DI/4DO

13. WDT (option): F81801U IO chipset for hardware watch dog timer support,

0~255 sec programmable

14. Expansion interface : 2 x PCIe mini card including one PCIe Mini card for

USB & SIM card interfaces, one PCIe Mini card for USB & mSATA interface

15. BIOS : Insyde UEFI BIOS

16. Dimension : 145 x 102 mm (3.5 inch)

17. Power : On board DC +12V (Note: -5V, -12V no support)

18. 3G Wireless : one 3G SIM card reader (for 3G mini card use)

6

1-3 Installing the SO-DIMM (for 3I380D-D90)

1. Align the SO-DIMM with the connector at a 45 degree angle.

2. Press the SO-DIMM into the connector until you hear a click.

7

Notices:

1.The connectors are designed to ensure the correct insertion. If you feel resistance,
check t h e connectors & golden fi nger direction, and realign the card.

2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of
the card fi rmly.

8

1-3-1.1 Removing the SO-DIMM (for 3I380D-D90)

1. Release the SO-DIMM by pulling outward the two retaining clips and
the SO-DIMM pops up slightly.

2. Lift the SO-DIMM out of its connector carefully.

9

1-4 Directions for installing the Mini Card

1. Unscrew the screw on the board

3. Gently push down the Mini Card and screw the screw back.

2. Plug in the Mini Card in a 45 angle

10

1-5 Packing List ( For 3I380D-D90)

Material Code Description Detail Specifi cation Quantit

7G1901-1481001-0 MB-3I380D-D90-00-001 LF,3I380D-D90-00,Rev.:001 1

1

6G8006-2347-0100 LEX Product Driver DVD LF, Intel Baytrail Driver 1

2

6G5212-0601-0200 60W Power Adapter,12V/5A,2.5 LF,L Type,FSP060-DBAE1,FSP 1

3

6G8001-2191-0400 Manual LF,M/B,3I380D 1

4

6G6003-7330-0100 Power Cable LF,L=9cm,2.0 1*4/DC JK 1

5

*The packing list above is for the users who purchase single motherboard. The users

who purchase the board with chassis may refer to the packing list in the Assembly Guide.

Please contact with your dealer if any of these items is missing or damaged

on delivery. And please keep all parts of the delivery package with packing

materials in case if you need to deliver or store the product in the future.

11

1-5-1 Packing List ( For 3I380D-I12)

Material Code Description Detail Specifi cation Quantit

7G1901-1480001-0 MB-3I380D-I12-00-001 LF,3I380D-I12-00,Rev.:001 1

1

6G8006-2347-0100 LEX Product Driver DVD LF, Intel Baytrail Driver 1

2

6G5212-0601-0200 60W Power Adapter,12V/5A,2.5 LF,L Type,FSP060-DBAE1,FSP 1

3

6G8001-2191-0400 Manual LF,M/B,3I380D 1

4

6G6003-7330-0100 Power Cable LF,L=9cm,2.0 1*4/DC JK 1

5

*The packing list above is for the users who purchase single motherboard. The users

who purchase the board with chassis may refer to the packing list in the Assembly Guide.

Please contact with your dealer if any of these items is missing or damaged

on delivery. And please keep all parts of the delivery package with packing

materials in case if you need to deliver or store the product in the future.

12

Chapter-2

Hardware Installation

2-1 Unpacking Precaution

This chapter provides the information how to install the hardware of 3I380D
Please follow section 1-5,1-5-1, 2-1 and 2-2 to check the delivery package and unpack
carefully. Please follow the jumper setting procedure.

NOTE!

1. Do not touch the board or any other sensitive components without all necessary
anti-static protection.

2. Please pay attention to the voltage limitation of DC-IN12 V 5 %.
Overuse of DC-IN voltage limitation or change to another power adapter
( not provided with this system ) will VOID warranty.

You should follow these
steps to protect the board from the static electric
discharge whenever you handle the board:

1. Ground yourself by a grounded wrist strap at all times when you
handle the 3I380D.
Well secure the ALLIGATOR clip of the strap to the end of the shielded wire lead from
a grounded object. Please put on and connect the strap before handling the
3I380D for harmlessly discharge any static electricity
through the strap.

2. Please use anti-static pad to put any components, parts, or tools on the pad whenever
you work on them outside the computer. You may also use the anti-static bag instead of
the pad. Please ask your local supplier for necessary parts on anti-static requirement.

3. Do not plug any connector or set any jumper when the power is on.

13

2-2 Unpacking checkup

First of all, please follow all necessary steps of section 2-1 to protect 3I380D

from electricity discharge. With reference to section 1-5,1-5-1

please check the delivery package again with following steps:

1. Unpack the 3I380D board and keep all

packing material, manual and driver disc etc, do not dispose !

2. Is there any components lose or drops from the board?

DO NOT CONTINUE TO INSTALL THIS BOARD!

CONTACT THE DEALER YOU PURCHASED

THIS BOARD FROM, IMMEDIATELY.

3. Is there any visible damage on the board?

DO NOT CONTINUE TO INSTALL THIS BOARD!CONTACT

THE DEALER YOU PURCHASED THIS BOARD FROM, IMMEDIATELY.

4. Check your optional parts (i.e. DDR, CF etc.), all necessary jumpers

setting to jumper pin-set, and CMOS setup correctly.

Please also refer to all information of jumper settings in this manual.

5. Check your external devices (i.e. Add-On-Card, Driver Type etc.)

for complete add-in or connection and CMOS setup correctly.

Please also refer to all information of connector connection in this manual.

6. Please keep all necessary manual and driver disc in a good condition for future

re-installation if you change your Operating System.

14

2-3 Dimension-3I380D

0

3.07

36.38

66.6

89.71

97.49

98.32
102

146

137.18

83.82

35.43

2.99

0

Ŗ6

0

Ŗ

3.4

03

04

03

03
04
05

27.81

04
05

26.66

146

03

142

03
04

130.85

137.18

03
03
04

111.79

04

05

92.73

03
04

05

73.67

03
04
05

8.1

100.89

2.99
0

94.39

94.81
102

03

6.5

SIM CARD

117

15

2-4 Layout-3I380D

CU3

(Bottom side)

CL4

CU2

(Bottom side)

CL3

CU1

(Bottom side)

CL2

CL1

SIM1

(Bottom side)

JSC2

CC2

BAT1

CG1

CG11

JSB1

CC11

SWP1

CU43

CU5

CU44

MPCE1

CKM1

CO1

MPCE2

CIO1

SWP2

CFP1

CPO1

CA1

CU41

CU42

FAN1

SODIMM1

(FOR 3I380D-D90)

HDMI1

CPI2

CPI1

16

2-5 Diagram- 3I380D-D90

CL4

CC2

BAT1

CL3

CL2

CL1

CU43

CU5

CU44

MPCE1

CO1

MPCE2

CFP1

SWP2

CPO1

CU41
CU42

FAN1

SODIMM1

CG1

JSB1

CC11

HDMI1

CPI2

CPI1

17

2-5-1 Bottom Side Diagram- 3I380D-D90

SATA 1

CU3

CU2

CU1

SIM1

BACK Panel-3I380D-D90

LAN4

USB

LAN3

USB

LAN2

USB

LAN1

SIM

18

VGA

HDMI

2-5-2 Diagram- 3I380D-I12

CL4

CC2

BAT1

CL3

CL2

CL1

CU43

CU5

CU44

MPCE1

CO1

MPCE2

CFP1

SWP2

CPO1

CU41

CU42

FAN1

CG1

JSB1

CC11

HDMI1

CPI2

CPI1

19

2-5-3 Bottom Side Diagram- 3I380D-I12

SATA 1

CU3

CU2

CU1

SIM1

BACK Panel-3I380D-I12

LAN4

USB

LAN3

USB

LAN2

USB

20

LAN1

SIM

VGA

HDMI

2-6 Install Memory

This motherboard provides one 204-pin Small Outline Dual In-line Memory Module (SODIMM)

socket for memory expansion available maximum to of 2GB/4GB/8GB DDR3L SDRAM.

DDR3L clock supports: DDR3 1333/1066MT/S

Valid Memory Confi gurations

Total Memory

DIMM1

System Accept or Not

Max.

DS/SS Accept

8GB

SS: Single Sided DIMMDS: Double Sided DIMM

NOTE!

The detected memory size is less than actual installed memory size since

some memory has been allocated for system use.

That’s how PC works with system memory.

Please refer to page 7 for installation of memory module.

21

2-7 List of Jumpers

JSB1: CMOS clear select

JSC2: COM2 RS422/RS485 select (Option)

2-8 Jumper Setting Description

A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF

as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2,

and 3. You could connect either pin 1 and 2 or 2 and 3.The below fi gure 2.2 shows the

examples of different jumper settings in this manual.

Figure 2.2

All jumpers already have its default setting with the plastic cap inserted as ON,

or without the plastic cap as OFF. The default setting may be referred in this

manual with a " * " symbol .

22

2-9 CMOS Data Clear

A battery must be used to retain the motherboard confi guration in CMOS RAM.

Close Pin1 and pin 2 of JSB1 to store the CMOS data.

To clear the CMOS,follow the procedures below:

1. Turn off the system and unplug teh AC power

2. Remove DC 12V power cable from DC 12V power connector

3. Locate JSB1 and close pin 1-2 for few seconds

4. Return to default setting by close pin 1-2

5. Connect DC 12V power cable back to DC 12V Power connector

JSB1: CMOS Data Clear

JSB1 Description

1-2 Normal set

2-3 CMOS data clear

Note: Normal work is open jumper

JSB1

*Normal Clear Setting

Note: Do not clear CMOS unless

1. Troubleshooting

2. Forget password

3. You fail over-clocking system

11
22
33

23

2-10 JSC2:COM2 RS422/RS485 select (Option)

JSC2 Description

RS422

*1-2

RS485

3-4

Note: RS422/485 setting by both H/W jumper and
BIOS CMOS setting

JSC2

44
22

*Normal RS485

33
11

24

Chapter-3

Connection

This chapter provides all necessary information of the peripheral's connections,
switches and indicators. Always power off the board before you install the peripherals.

3-1 List of Connectors

CPI1: DC-in 1x4pin(2.0mm) Red wafer connector

DC-in 1x2 pin(2.0mm) Red wafer connector

CPI2

:

DC-in 2x4 pin(2.0mm) wafer connector (Option)

CPI11

:

Li 3V battery holder

BAT1

:

DC +5/+12V output 1x4 pin(2.0mm) Black wafer connector

CPO1

:

Front panel port 2x6 pin(2.00mm) wafer for LED

CFP1

:

Power Button /Power LED(Blue) (Option)

SWP1

:

Power Button 1x2 pin(2.0mm) wafer

SWP2

:

CPU fan 1x3 pin(2.54mm) wafer

FAN1

:

DSUB VGA connector

CG1

:

DSUB VGA wafer connector (Option)

CG11

:

HDMI1

CA1

CC1

CC11

CC2

CIO1

CO1

CKM1

CL1/CL2/CL3/CL4

CL11/CL21/CL31/CL41

CL32/CL42

CU1/CU2/CU3

CU41

CU42

CU5

CU43/CU44

SATA1

MPCE1/MPCE2

SIM1

MSD1

SODIM1

HDMI Type A 90° connector

:

Mic-in/Line out/Line in 2x5 pin(2.0mm) wafer connector (Option)

:

DB9 COM1 connector (Option)

:

COM1 2x5pin(2.0mm) wafer

:

COM2 2x5pin(2.0mm) wafer

:

DI port 0 ~ 3, DO port 0 ~ 3 2x5 pin (2.0mm) wafer (Option)

:

2

I C 4pin (1.25mm) wafer

:

KB/MS port 1x6 pin (1.25mm) wafer connector (Option)

:

LAN RJ45 connector

:

LAN3/4 port 2x4 pin(2.0mm) wafer connector (Option)

:

LAN3/4 LED port 1x4 pin(1.25mm) wafer connector (Option)

:

USB port 1/2/3 Type A connector

:

USB2.0 port 4pin(1.25mm) wafer (share with MPCE1 USB signal)

:

USB2.0 port 4pin(1.25mm) wafer (share with MPCE2 USB signal)

:

USB3.0 port 5pin(1.25mm)wafer (For CU001 use)

:

USB2.0 port 4pin(1.25mm) wafer

:

SATA port 0 (Gen III) connectors 7pin

:

Mini card port 1/2 sockets 52pin

:

SIM port 1 card socket(push-push)

:

MicroSD port socket(push-push) (Option)

:

SO-DIM DDR3L 1.35V DRAM Socket

:

25