Leviton RTD01-10 Installation Instructions Manual

4 Speed Quiet Ceiling Fan/Light Control – Single Pole (One location)

Cat. No. RTDØ1-1Ø,

Fan Control

Rated: 1.5A-120VAC, 60Hz

Full Range Dimming Incandescent Lamp Load

Rated: 300W-120VAC, 60Hz

INSTALLATION INSTRUCTIONS

DI-000-RTD01-02B

Tools needed to install your Fan Speed
Control:

Slotted/Phillips Screwdriver Electrical Tape
Pliers Pencil
Cutters Ruler

Color Change Option:

If a color change kit is provided with your device,
proceed with the following step if you need to change
the color. Otherwise, proceed with the "Installing

Fan Speed/Light Control by itself or with other
devices" section.

Changing the color of your Fan Speed/
Light Control

Your Fan Speed Control includes two color options. The
Control ships with the White frame attached. To change
color of frame, proceed as follows:

Installing Fan Speed/Light Control by
itself or with other devices:

If installing Control in a single device application,
proceed with the MULTI-FAN CONTROL section. If
installing Control in a multi-device application,
proceed as follows:

MULTI-DEVICE APPLICATION

NOTE: There is NO derating necessary for multi-gang

installations of this Fan Speed Control.

MULTI-FAN CONTROL

Any number of fans of the same type may be
controlled by a single fan speed control provided that
the total amperage of the fans do not exceed the
amperage of the fan speed control.

INSTALLING YOUR FAN SPEED/LIGHT
CONTROL

NOTE: Use check boxes when Steps are

completed.

WARNING: To avoid fire, shock, or

death; TURN OFF POWER at circuit
breaker or fuse and test that power is off
before wiring!

Step 1

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFFONOFF

ONOFF

ONOFF

ONOFF

ONOFF

WARNINGS AND CAUTIONS:

•To be installed and/or used in accordance with appropriate electrical codes
and regulations.

• If you are unsure about any part of these instructions, consult a qualified
electrician.

•To avoid overheating and possible damage to this device and other equipment,
do not install to control a receptacle, fluorescent lighting, a motor- or a
transformer-operated appliance other than appropriate ceiling fans and
incandescent lamps.

WARNINGS AND CAUTIONS:

•To reduce the risk of fire or electrical shock, this control is to be used with
ceiling fans that are marked as suitable for use with solid-state fan speed control
and is rated 120VAC, total load 1.5 amperes maximum.

•For use on ceiling paddle fans with split-capacitor or shaded pole motors only.
Please refer to manufacture's instructions or rating label on the motor to
confirm type. Use with any other types of motors or equipment may cause
overheating and/or damage to the motors or equipment.

• Disconnect power at circuit breaker or fuse when servicing fixture.

• Use this device only with copper or copper clad wire. With aluminum wire use
only devices marked CO/ALR or CU/AL.

Strip 5/8"

(1.6 cm)

Cut

(if necessary)

√

Single-Pole Wiring Application:

Preparing wires:

Black

Red

Neutral

Green

Ground

Yellow

O

F

F

M

A

X

H

I

M

E

D

L

O

O

F

F

M

A

X

H

I

M

E

D

L

O

Push in side at tab
to release. Remove
frame and knob.

Press on knob. Line up
tabs on back of frame and
press in side to attach

Strip Gage

• Pull off pre-cut insulation from Control leads.

• Make sure that the ends of the wires from the
wall box are

straight (cut if necessary)

.

• Remove 5/8" (1.6 cm) of insulation from each
wire in the wall box (shown).

Step 3

Step 2

Insert wires

straight then twist

clockwise

Electrical

Tape

5/8"
(1.6 cm)

OPERATION

TROUBLESHOOTING

• Fan does not turn ON or does not run Multispeed

- Circuit breaker or fuse has tripped.

- Fan is not connected to line Neutral.

- Switch on Fan not set to HIGH position.

- Fan and light miswired.

• Light does not turn ON

- Circuit breaker or fuse has tripped.

- Bulb has burned out.

- Lamp is not connected to line Neutral.

- Switch on Fan unit controlling Light is not in
the ON position (if applicable).

- Fan and light miswired.

For non-standard wiring applications, refer

to Wire Nut and Conductor Size Chart

Connect wires per WIRING DIAGRAM as
follows: Screw wire nuts on clockwise making

sure no bare conductors show below the wire
connectors. Secure each connector with
electrical tape.

• Green control Ground lead to Green or bare
copper wire in wall box.

• Black control lead to Line (Hot) wall box wire
removed from old switch.

• Red control lead (motor Hot) to Black Fan wall
box wire.

• Yellow control lead (Light Hot) to Black Light
wall box wire.

• Proceed to Step 6.

Testing your Fan Speed/Light
Control prior to mounting in wall
box:

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal
and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned
prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York
11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper
environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or
implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied
warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation,
damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty,
whether based on contract, tort or otherwise.

Fan Speed/Light Control
Mounting:

TURN OFF POWER AT CIRCUIT

BREAKER OR FUSE.

Restore Power: Restore power at

circuit breaker or fuse. Installation is
complete.

Step 5

DI-000-RTD01-02B

Step 4

Step 6

WIRE NUT / # OF CONDUCTOR

COMBINATION CHART

1- #12 w/ 1 to 3 #14, #16 or #18
2- #12 w/ 1 or 2 #16 or #18
1- #14 w/ 1 to 4 #16 or #18
2- #14 w/ 1 to 3 #16 or #18

O

F

F

M

A

X

H

I

M

E

D

L

O

• Restore power at circuit breaker or
fuse.

• Carefully holding control as
shown, proceed as follows:

Dimmer: Rotate top knob control
clockwise and counter-clockwise.
Lights should turn DIM and BRIGHTEN
accordingly.

If light does not turn ON, refer to the
TROUBLESHOOTING section.

Fan Speed: Rotate bottom knob to the

MAX position. Fan should turn ON to
highest level. Rotate knob to the
remaining levels: HI, MED, and LO.
Fan speed should change accordingly.

If fan does not turn ON, refer to the
TROUBLESHOOTING section.

O

F

F

M

A

X

H

I

M

E

D

L

O

O

F

F

M

A

X

H

I

M

E

D

L

O

Installation may now be
completed by carefully
positioning
all wires to provide room
in wall box for control.
Mount control
into box with mounting
screws supplied. Attach
wallplate.

Dimmer:

ON

Rotate top control knob
clockwise – Lights will turn
ON at level set by knob.

OFF

Rotate top control knob fully
counter-clockwise – Lights
will turn OFF.

BRIGHTEN

Rotate top control knob
clockwise to desired brightness level.

DIM

Rotate top control knob counter-clockwise to desired
dim level.

Fan Speed:

ON

Rotate bottom control knob to each of the four levels:
MAX, HI, MED, and LO – Fan will increase or
decrease in speed respectively for desired level.

OFF

Rotate bottom control knob counter-clockwise to the
OFF position – Fan will turn OFF.

Hot (Black)

Neutral (White)

Fan

Light

Fan Speed/Dimmer

Black

Green

Ground

Black

Black

WhiteWhite

Red (Motor) Hot
Yellow (Light) Hot

Line

120VAC, 60Hz

O

F

F

M

A

X

H

I

M

E

D

L

O

PRODUCT INFORMATION

•For technical assistance, contact us at

1-800-824-3005

.

• Visit our website at

www.leviton.com

.

Step 4a
con’t

Single-Pole Wiring Application:

Step 7

Step 3a
con’t