Leviton D2MSD Installation Manual

Download

Page 1

GROUND

LOAD

LINE

To Light

From

Branch Circuit

Getting Started Guide

WEB VERSION

Cat. No. D2MSD

DI-000-D2MSD-02A

MOTION SENSING DIMMER

GEN

Easy Wi-Fi lighting control for the whole home

See the complete line of My LevitonTM app compatible

dimmers, switches, plug-ins, and controllers at:

leviton.com/decorasmart

Welcome

Leviton’s Decora Smart Wi-Fi 2nd Gen Motion Sensing Dimmer makes it easy and convenient to control lighting in your home automatically, with ON/OFF, Dim/Bright control, and built-in motion and ambient light detection.

To save energy, the dimmer can be set to turn lights on when motion is detected, and to turn lights off when the room is unoccupied. You can also have the lights come on at a lower level at night or utilize the guidelight feature to illuminate your way in the dark. You can even use the Motion Dimmer to control multiple Decora Smart devices in a room together, based on occupancy, with the My Leviton app.

Control lighting how you want with built-in sensing. Use your voice with Amazon Alexa, Google Assistant, or Apple Siri, or use the My Leviton app, even when you are away from home.

We are here to help

ONLINE

decorasmartsupport.leviton.com

dssupport@leviton.com

CHAT

www.leviton.com/support

CALL

1-8 00- 824 -30 05 ( USA )

1-800-405-5320 (Canada)

Your Motion Dimmer works with:

• Dimmable LED, dimmable CFL,

incandescent, and MLV lighting.

• For ON/OFF control of non-dimmable

bulbs, such as ﬂuorescent loads, select “Non-dimmable” bulb type in the My Leviton app, under device settings.

•

Do not use your dimmer with electronic low-voltage or motor loads.

• Not for use with aluminum wire.

• Installation in metal wall boxes or

with metal wall plates may result in poor RF performance.

• This device responds to temperature changes;

do not mount directly above a heat source or in a location where hot or cold drafts will blow directly on the sensor.

• For indoor use only.

•

For compatible LED bulbs, go to: leviton.com/LED

RATINGS

General Use 120VAC, 60Hz LED / CFL Incandescent 450W MLV 450VA Operating Temperature 0°C - 40°C (32°F - 104°F) Operating Humidity 10% - 90% non-condensing Storage Temperature Range -10°C – 85°C

NETWORK

Wi-Fi

Security

Bluetooth v5.0

MY LEVITON APP

iOS version 12.0 or later

oid version 8.0 or later

Andr

300W

802.11 b/g/n netw

2.4GHz only WPA, WPA2, or WPA3 security,

or open

orks -

At a glance

PIR Motion Sensor

• Detects motion to determine

occupancy status.

• Optional Red LED feedback

to indicate motion is detected (conﬁgurable in the My Lev iton app).

Status LED

• Provides

connectivity and device status feedback.

• Illuminates when

the lights are OFF so you can ﬁnd the dimmer in the dark (conﬁgurable in the My Leviton app).

Brightness indicator lights

•

Displays light level when adjusting brightness.

ON / OFF Button

• Press to toggle the lights

ON or OFF

OFF means OFF

• Ensures low-wattage LED

bulbs always turn OFF.

Guidelight

• Enable in the app to turn on

a guidelight at night instead of the room lights when motion is detected.

Air gap switch

•

Ambient Light Sensor

•

Dim/bright bar

•

This feature will stop power to the dimmer. Gently pull out the tab to remove power to the dimmer and lights. After servicing is complete, push back in for normal operation.

Detects amount of ambient light in the space.

Manually adjust light levels.

FCC COMPLIANCE STATEMENT

The enc losed devic e complies wit h Part 15 of the FCC Rules. O peration is subjec t to the following two co nditions: (i .) This de vice may not cau se harmful i nterferenc e (ii.) This de vice must accept any i nterferenc e received, in cluding inte rference that may cause u ndesired operat ion. Any change s or modiﬁcat ions not expre ssly approved by Levito n could void the user’s au thority t o operate this equip ment. This e quipment has be en tested and fo und to comply w ith the limit s for a Class B di gital device, pursu ant to part 15 of t he FCC Rules. The se limits are d esigned to p rovide reas onable protec tion again st harmful i nterferenc e in a resident ial install ation. This equip ment generates uses and can radiate radio frequen cy energy an d, if not instal led and used in accordance w ith the inst ruction s, may cause harmful i nterferenc e to radio commu nications. However, th ere is no guara ntee that inte rference will not occur in a part icular ins tallatio n. If this equi pment does ca use harmful i nterference to radio or television recept ion, which ca n be determin ed by turning t he equipmen t off and on, the us er is encoura ged to try to co rrect the in terference b y one or more of th e follow ing measures:

• Reorient or rel ocate the rec eiving antenna.

• Conne ct the equi pment into an outlet on a circuit dif ferent from that to which the

eceiver is connected.

• Increa se the sepa ration between the equip ment and receiver.

• Consult the de aler or an exper ienced radio/TV tec hnician for h elp.

C CAUTIO N

Any cha nges or modiﬁc ations not exp ressly approved by Lev iton Manufac turing Co., Inc., co uld void the user ’s authority to operate th e equipment.

FCC SUPPLIER’S DECLARATION OF CONFORMITY

Model D2MSD Wi-Fi Mot ion Sensing Dimmer is man ufactured by L eviton Manufactur ing Co., Inc. 201 N. Se rvice Road, Melville, NY 11747. www.levit on.com This de vice complie s with part 15 of the FCC Rules. Op eration is subject to the follow ing two cond itions: (1) This dev ice may not cause harmful interference, and (2) this d evice must ac cept any inter ference rece ived, includ ing interfe rence that may cause undesired operation.

IC STAT EME NT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is s ubject to th e following t wo conditio ns: (1) this d evice may not cause i nterference, and (2) thi s device mus t accept any interference, in cluding inter ference that m ay cause undesired o peration of the device.

RF EXP OSURE AND CO -LOCATION

To comply wit h FCC OET Bullet in 65 and ISED RF ex posure limit s for general po pulation and unc ontrolled e xposure, th is device shall be in stalled an d operated w ith a minimum dist ance of 7.9 inches (20 cm) betw een the radia tor and your body. Also, mu st not be co-lo cated or opera ted in conjunctio n with any oth er antenna or transm itter.

Decora and Decora Smart are the registered trademarks of Leviton Manufacturing Co., Inc., registered in the U.S., Canada, Mexico and China.

Google and Google Play are trademarks of Google LLC. Alexa, and related logos are trademarks of Amazon.com, Inc. or its afﬁliates. Apple trademarks of Apple Inc., registered in the U.S. and other countries.

Use of the Works with Apple badge means that an accessory has been designed to work speciﬁcally with the technology identiﬁed in the badge and has been certiﬁed by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Use herein of other third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their respective owners; such use is not meant to imply afﬁliation, sponsorship, or endorsement. No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.

Patents covering this product, if any, can be found on Leviton.com/patents.

Levito n Manufactu ring Co., Inc. 201 North Serv ice Road, Melville, NY 11747

, HomeKit®, and Siri® are

1 2 3 4

Features Before you installMotion Sensing

• Hands-free; automatically turns lights ON/OFF

when motion is detected.

• Voice control works with Hey Google, Amazon

Alexa, or Apple Siri.

• Easy app-based conﬁguration of motion sensor

settings and modes.

•

Allows other connected Decora Smart Wi-Fi devices in a room to be activated based on room occupancy.

• Supports 3-Way/Multi-location with Wired

Companions and Wireless Anywhere Companions.

• Use the app to enable a Guidelight, that turns

ON when motion is detected at night, to illuminate your way in the dark.

• Advanced settings for:

• Fade rates

• Pre-set light level or Return to last level

• Minimum dim / Maximum brightness

• Bulb types including non-dimmable loads

For more information and features, visit:

leviton.com/decorasmart.

• The D2MSD’s PIR Motion Sensor has a 180° ﬁeld-of-

view, with a maximum sensor coverage area of 900 sq. ft. (30 x 30 ft).

• Motion Sensor Calibration: can be used in the My

Leviton app to test the Motion Sensor’s coverage area, customize the sensor sensitivity, and enable ambient light settings.

Horizontal field of view

15 FT.

10 FT.

15 FT.

Wall

Vertical field of view

Floor

20 FT.

30 FT.

20 FT. 30 FT.

Major motion coverage 900 ft

Minor motion coverage 400 ft

NOTE: Device should be installed on the wall, 40-48

inches above the ﬂoor. Sensor modes can be conﬁgured under device

settings in the My Leviton app:

• Occupancy Mode: will automatically turn lights on

when motion is detected, and will turn lights off when no motion is detected.

• Vacancy Mode*: requires you to manually turn

lights on, but will still turn the lights off when no motion is detected.

• Guidelight: can be enabled to turn on at night and

softly illuminate a space when motion is detected, instead of turning on the room lights.

* Pro Tip: Vacancy mode can be used to comply

with 2019 Title 24, Part 6 Vacancy Control Device Requirements.

65 7 8

Installation requires electrical knowledge. If you are unsure of any steps, consult an electrician.

Things to consider:

To control the motion dimmer from more than one location, such as in a 3-way or multi-way, you will need either a wired DD00R or DD0SR Companion device, or a wire-free DAWDC or DAWSC Anywhere

Companion device (see page 14).

Learn more about Companion devices and ﬁnd connection instructions at

leviton.com/decorasmart

What you need to make it work:

A 2.4GHz Wi-Fi network with high-speed internet.

An iOS (Version 12.0 or later) or Android (Version

8.0 or later) mobile device.

NOTE: Make sure Wi-Fi and Bluetooth are enabled

on your mobile device.

A My Leviton cloud account (set up through the My Leviton app).

Identify your wires

WARNING: TO AVOID FIRE, SHOCK, OR DEATH, turn off power at the circuit breaker.

Check your wall box:

1. Remove wallplate and disconnect existing switch.

2. Restore power. Carefully test wires with voltage

tester to ﬁnd the Line (Hot) wire.

3. Turn off power at the circuit breaker.

4. Mark the wires as shown below. Please note Neutral

wires are required to operate this device.

Quick tip: Neutral wires are typically white and will

be found bundled inside the electrical box.

To Light

LOAD

LINE

From Branch Circuit

If your wall box looks different,

call an electrician.

NEUTRAL

GROUND

Page 2

Wire your Motion

GROUND

LOAD

To Light

LINE

GROUND

TRAVELER

From

Branch Circuit

WEB VERSION

Dimmer

Single pole installation:

1. Work only one connection at a time.

2. Connect wires as shown, using the included

wire connectors.

NOTES:

• Neutral connection is required.

• The YELLOW/RED Traveler wire is only used in hard-

wired 3-way applications. Remember to put a wire connector on the YELLOW/RED Traveler even if not in use.

To Light

LOAD

LINE

NEUTRAL

GND

TRAV

TRAVELER

If your wall box contains a different wiring

conﬁguration, contact Leviton’s Technical

Support team or consult an electrician.

LINE

NEUTRAL

GROUND

From Branch Circuit

NEUTRAL

GROUND

Test and install

1. Restore power. Status LED should ﬂash GREEN.

This will indicate that your Motion Dimmer is ready to be enrolled.

2. After powering on

the Motion Dimmer to conﬁrm it is receiving power, turn the power back off again at the breaker. Do this prior to completing the installation.

Turn off power at the circuit breaker before screwing in your Motion Dimmer.

3. Gently push wires

into wall box. Screw Motion Dimmer to box.

4. Snap on Decora

and restore power.

Once power is restored, the status LED will blink GREEN, indicating your device is in Setup mode. See page 16 if your status LED is not blinking GREEN.

Your Decora Smart Motion Sensing

Dimmer is ready to control your lights.

wallplate

Congratulations!

Get the app Device setup

visit my.leviton.com and select the link, or s

To download the app,

can

the QR code below for your device.

Changing Sensor mode

You can use the My Leviton app to adjust all Motion Sensor settings. If you do not have Wi-Fi available, you can switch between Occupancy and Vacancy mode on the device if needed. The Motion Sensing Dimmer is defaulted to Occupancy mode.

NOTE: The default Vacancy settings can be used to

comply with 2019 Title 24, Part 6 Vacancy Control Device requirements.

1. Press the ON/OFF button 7 times in sequence.

2. The device will change Sensor mode and the Status

LED will brieﬂy ﬂash:

• GREEN, if in Occupancy mode

• RED, if in Vaccancy mode

• The Decora Smart Wi-Fi 2nd Gen Motion Sensing

Dimmer can be connected to the My Leviton service, Apple HomeKit, or both.

• For voice control with Amazon Alexa or Google

Assistant, you will need to set up the device with My Leviton.

• For voice control with Siri, you will need to connect

your device to Apple HomeKit. See page 15 for instructions on how to add your device to Apple HomeKit.

Add your device to My Leviton

1. Make sure the device is in Setup mode (status LED

should be blinking GREEN). If the status LED is not blinking GREEN, see page 16 for instructions on how to put the device in Setup mode.

2. Launch the My Leviton app.

3. Log in or choose “Sign Up” to create a new account.

4. Follow the instructions on the screen.

5. Once logged in, tap the “+” in the upper right corner

and select “Add Device.”

6. Follow the app instructions to add your device and

to connect it to your home Wi-Fi network.

Test My Leviton app control

1. Open the My Leviton app.

2. Tap icon to turn the

Motion Sensing Dimmer ON/OFF.

Quick tips

• The My Leviton app includes many features such

as: room occupancy based on motion, room scenes, whole-house activities, remote control, Vacation mode, and advanced options for bulb type, fade rates, preset light level, and minimum dim/maximum brightness.

• Self-service support options can be found in the My

Leviton app or at decorasmartsupport.leviton.com.

9 10 11 12 13

Connect to My Leviton partners (optional)

works with

Hey Google

Visit my.leviton.com for a complete list of

compatible smart home products.

1. Tap menu icon in

lower right corner.

2. Tap Integrations, locate the

desired service, select it, and follow the instructions.

Pair an Anywhere Companion

1. Place the Anywhere Companion in Pairing

mode by pressing the top rocker 5 times. Its Status LED will blink GREEN.

2. Place the primary Decora Smart Wi-Fi Motion

Sensing Dimmer into Pairing mode by pressing the ON/OFF button 5 times. The Status LED will ﬂash GREEN/AMBER.

3. The Decora Smart Wi-Fi Motion Sensing

Dimmer will automatically pair to the Anywhere Companion in Pairing mode in wireless RF range. Once paired, the Status LED will quickly ﬂash GREEN to show a successful connection.

Learn more about Companion devices and ﬁnd connection instructions at leviton.com/decorasmart.

Add your device to Apple HomeKit (optional)

NOTE: Skip Step 1 if your device is already enrolled in

My Leviton and on your Wi-Fi network.

1. Make sure the device is in Setup mode (status LED

should be blinking GREEN). If the status LED is not blinking GREEN, see page 16 for instructions on how to put the device into setup mode.

Using an iOS device, open the Apple Home app and select “Add Accessory”

3. Locate and scan the HomeKit setup code on your

device or on the front page of this Getting Started Guide.

4. Follow the instructions in the Apple Home app.

5. Once the device is set up, you will be able to voice

control your Decora Smart Wi-Fi Motion Sensing Dimmer with Apple Siri.

Diagnostic LED

If your device is not connecting to the My Leviton app, the Status LED can be used as a diagnostic tool. Press the ON/OFF button for at least 2 seconds (but no more than 7 seconds), and then release. The Status LED will blink a diagnostic code for 2 seconds.

CO L O R STAT U S

Amber Not connected to Wi-Fi.

Green/Amber, Alternating

Green

Connected to Wi-Fi, but unable to connect to the My Leviton cloud.

Connected to Wi-Fi and My Leviton cloud, but unable to set the time from the internet.

Connected to Wi-Fi, and the My Leviton cloud is working properly.

1514 16 17

Status LED

COLOR ACTIVITY STATUS

Green Flashing

Green Slow Blink

Green or Off

Amber Slow Blink

Green/ Amber

Red Blink

Green/Red/ Amber

Solid

Alternating Blink

In Setup mode and r to a Wi-Fi network.

Connecting to a Wi-Fi network on power up.

Normal operation. Can be conﬁgured in a setup.

Device is not connected to the WiFi network, but is attempting to reconnect.

Device is in wireless Anywhere Companion Pairing mode.

Wireless Anywhere Companion devices have unpaired or are at max number of paired devices.

Identify feature triggered from the My Leviton app.

eady to be added

Setup mode

Hold the ON/OFF button for 7 seconds until the status light turns AMBER. Then release.

2. The status light will ﬂash GREEN.

The device is now in Setup mode.

NOTE: To exit, hold ON/OFF button

for 7 seconds while in Setup mode.

Factory default reset

Hold the ON/OFF button for 14 seconds.

2. After the ﬁrst 7 seconds, the status light will turn

AMBER. Continue to hold.

3. After 7 more seconds, the status light will quickly

ﬂash RED/AMBER.

4. Release the ON/OFF button and the device will reset.

What to do if...

When power is applied, the manual buttons do not control the lights and the lights do not turn ON when motion is present:

• Verify that the wiring connections are secure.

• For proper operation, the Motion Dimmer needs a Line (Hot),

Neutral, Load, and Ground connection.

When power is applied, the light turns ON, but Motion Dimmer is not able to change the light level:

• Conﬁrm that the white conductor is a Neutral.

• If using LED or CFL bulbs, make sure they are dimmable.

Motion Dimmer does not dim low enough, or begins to ﬂicker at the low end of the dimming range:

• Use the My Leviton app to increase the minimum dim level

to the point that it does not cause the LED bulb to ﬂicker.

Lights do not turn ON when motion is detected:

Motion may be beyond sensing range - move closer to device.

•

• Go to Motion Sensor Calibration in the My Leviton app to

increase the sensor sensitivity and coverage area, or adjust the ambient light settings.

• Make sure you are in Occupancy mode.

Lights always stay ON:

• Check app settings for how long the Motion Dimmer waits

before turning the lights OFF after no motion is detected.

• Check that Dimmer is not installed near a heat source or

detecting motion from an adjacent area (e.g., hallway trafﬁc)

• Make sure you are in Occupancy mode.

Intermittent dimmer operation:

• Conﬁrm that the Load does not exceed its ratings.

Not connected to Wi-Fi:

• If your device is set up in the My Leviton app, select your

device, and then select “Device Settings“. On the “Device Settings” screen, select “Reconﬁgure Wireless“. Follow prompts to reconﬁgure device and update Wi-Fi settings.

How do I clean my device?

• To clean use a damp cloth with mild soap. DO NOT use

disinfecting products, including foggers, sprays or other types of atomized cleaning agents.

Visit leviton.com/decorasmart or contact Technical Services for additional help.

Safety ﬁrst

WARNINGS:

• TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER a

breaker or fuse and test that power is off before wiring!

• TO AVOID FIRE, PERSONAL INJURY, OR PROPERTY DAMAGE,

NOT install to control a receptacle, a motor, or transformer

operated appliance.

• This product is to be installed and/or used in accordance with

lectrical codes and regulations.

• For indoor use only.

•

If you are unsure about any par t of these instructions, consult an electrician.

CAUTIONS:

• Use with compatible 120V dimmable LED/CFL bulbs, incandescent,

alogen, or magnetic low-voltage (MLV) ﬁxtures. For ON/OFF control of non-dimmable bulbs, such as ﬂuorescent li ghting, the non-dimmable bulb type must be selected in the My Lev iton app. Use a Leviton electronic low-voltage dimmer to control electronic (solid state) lowvoltage transformers. For a list of compatible LED and CFL bulbs, refer to www.leviton.com.

•

DO NOT mix bulb types when multiple bul bs are used with one dimmer. Using the same make/model of each bulb will enhance dimmer performance.

• The Decora Smar t D2MSD dimmer is not compatible with standard

3-way or 4-way switches. It must be used with up to 4 Decora DD00R-DL or DD0SR companions for wired multi-location dimming.

• Maximum wire length from dimmer to all installed companion dev ices

annot exceed 300 ft (90m).

• Save this instruction sheet. It contains impor tant technical data,

long with testing and troubleshooting information, which will be

useful after installation is complete.

• Dimmer may feel warm to the touch during normal operation.

• Recommended minimum wall box depth is 2-3/4 in.

• Use this dimmer with copper or copper-clad wire only.

• Leviton Wi-Fi enabled devices rely on Wi-Fi communication.

r customers looking to install a large number of devices, it is recommended to consult the wireless network’s access point speciﬁcations to determine the maximum number of supported Wi-Fi devices. In some cases, for example large installations, it may be necessar y to upgrade to newer high-performance wireless grade access points to ensure proper operation.

ADDITIONAL RATINGS:

• Purpose of Control: Operating Control

• Action Control Type: 1

• Pollution Degree: 2

• Impulse Voltage: 2500V

• Disconnection Type: Micro

t circuit

Smart

Limited 2 Year Warranty & Exclusions

For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty, call 1-800-824-3005.

FOR CANADA ONLY

For warranty informat ion and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC, to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9, or by telephone at 1-800-405-5320.

Leviton D2MSD Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual