Page 1
bitwise™
WEB VERSION
INSTALLATION GUIDE
ENGLISH
© 2015 Leviton Mfg. Co., Inc.
BWRMT
000-BWRMT-000Cat. No.
DI-000-BWRMT-05A
WARNINGS & CAUTIONS
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never push objects of any
kind into this product through openings, as they may touch dangerous voltages.
• WARNING: TO AVOID DEATH OR SERIOUS PERSONAL INJURY never touch uninsulated
wires or terminals unless the wiring has been disconnected at the network interface.
•
Read and understand all instructions. Follow all warnings and instructions marked on the product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or laundry tub,
in a wet basement, or near a swimming pool.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the components are
designed specifically for use in wet locations.
• Use caution when installing or modifying communications wiring or components.
• SAVE THESE INSTRUCTIONS.
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that
products manufactured by Leviton under the Leviton brand name (“Product”) will be free from
defects in material and workmanship for the time periods indicated below, whichever is shorter:
• OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date.
• OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture
date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture
date. • Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date
of purchase. Note: Primary (non-rechargeable) batteries shipped in products are not warranted.
Products with Windows
corrupted operating systems to factory default at no charge, provided that the product has been used
as originally intended. Installation of non-Leviton software or modification of the operating system voids
this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement,
at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves
the right to replace product under this Limited Warranty with new or remanufactured product. Leviton
will not be responsible for labor costs of removal or reinstallation of Product. The repaired or
replaced product is then warranted under the terms of this Limited Warranty for the remainder of the
Limited Warranty time period or ninety (90) days, whichever is longer. This Limited Warranty does
not cover PC-based software products. Leviton is not responsible for conditions or applications
beyond Leviton’s control. Leviton is not responsible for issues related to improper installation,
including failure to follow written Installation and operation instructions, normal wear and
tear, catastrophe, fault or negligence of the user or other problems external to the Product. To
view complete warranty and instructions for returning product, please visit us at www.leviton.com.
For Technical Assistance Call: 800-824-3005 - www.leviton.com
LEVITON LIMITED WARRANTY
®
Operating Systems: During the warranty period, Leviton will restore
FCC COMPLIANCE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC STATEMENT: This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation
DI-000-BWRMT-05A
of the device.
FOR CANADA ONLY: For warranty information and/or product returns, residents of Canada should
contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
TRADEMARK DISCLAIMER: Use herein of third party trademarks, service marks, trade names, brand
names and/or product names are for informational purposes only, are/may be the trademarks of their
© 2015 Leviton Mfg. Co., Inc.
respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
Page 2
OVERVIEW
WEB VERSION
The Room Remote can be added to a Leviton® bitwise™ system utilizing iOS®/Android® Devices
for control or can be used as the sole point of control. Each system needs at least one RF receiver
and a compatible Leviton bitwise Controller (see Requirements for details). This document will guide
you through connecting the required hardware. For programming, please refer to the Room Remote
Programming Guide.
REQUIREMENTS
Hardware
• Room Remote - BWRMT
• RF to Serial Receiver – BWRRR
• Compatible Leviton bitwise Controller - BWBC1,BWBC2, Gen 2 BWBC4
(Not compatible with Gen1 BWBC4)
Software
• Project Editor - v1.9.60 or later
• BWBC1 Firmware - v131115-0.1fw
• BWBC2 Firmware - v131115-0.1fw
• BWBC4 Firmware – v1.3.16
CONNECT THE RF RECEIVER TO THE CONTROLLER SERIAL PORT
Each RF Receiver is capable of supporting up to 255 RF Room Remotes. The RF Receiver connects
via RS232 to a compatible Leviton bitwise Controller. In most cases, it will be easiest to use a serial
port with terminal connectors rather than the DB-9. The remaining instructions assume you are using a
serial port with terminal block connections.
ROOM REMOTE WIRE BITWISE CONTROLLER RS232 PORT
Black GND - Ground
White RXD - Receive
Red 4+12 VDC - Power
NOTE: If you need to extend the cable for the RF Receiver we recommend using 3 conductor shielded
cable or 2 pairs of Cat5/6 network cable. If using Cat5/6, use the Orange pair for signal and ground
and the Green pair for Power and ground. (Yes, connect ground to one conductor of each pair).
RF RECEIVER PLACEMENT
Try to place the RF Receiver in a central location close to where the remote(s) will be used, away
from sources of RF noise and large amounts of metal (refrigerators, furnaces etc…). The antenna
whip should be vertical in most cases but may be adjusted as necessary for optimal reception.
ADDRESS THE REMOTE(S)
1. Hold the “OK” and “B” buttons until the res status LED turns solid red (figure 1).
2. Enter a THREE digit address (001-255) using the numeric keys.
3. Press the “OK” key.
The LED will blink twice if the process was successful and 5 times if an invalid sequence was entered
or the procedure timed out.
CONTACT
Technical Support: 1-800-824-3005
Email: sabw@leviton.com
support@bitwisecontrols.com
Web: www.leviton.com/automation
DI-000-BWRMT-05A
© 2015 Leviton Mfg. Co., Inc.
FIGURE 1
Press and Hold
at the same time
Loading...