LevelOne IGP-0101 User guide

1

IGP-0101

Industrial Gigabit POE Injector, 802.3at PoE+, 36W

User Manual

2

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received; including interference that may cause
undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date. Please check with your local distributors
for the latest information. No part of this document can be copied or reproduced in any
form without written consent from the company.

Trademarks:
All trade names and trademarks are the properties of their respective companies.

Copyright © 2013, All Rights Reserved.

3

NOTE:

Always make sure the total length of the TX cable DOES NOT exceed 100meter. Total length is
defined as length A + length B

PD

Remote Switch
A

B

Maximum total cable length is 100meter.

During 100Mbps transmission, the maximum total cable length is 100 meter.

During 1000Mbps speed transmission, recommend maximum cable length less than 90 meter is
more desired.

POE signal attenuates every meter, the built-in transformer allows the attenuation to reach 100
meter long to follow IEEE802.3af / at standard. the higher quality of PD you connected to, the
more reliable the network will be. When connect to a poor quality PD, it can not generate strong
signal to send to remote switch. Always make sure you have a high quality PD to perform a
desired network.

Length A + Length B < 100 meter

4

Power connection

The provided 4 pin terminal block can be connected with 48VDC to 56VDC power source. Always
Make sure your input voltage is within this supported voltage range.

To make power connection – Follow the printed polarity for V+, V-, Ground. Connect positive wire
to V+ , connect negative wire to V-, also connect neutral wire to ground. This unit can be
connected to two power input.
+V1- is for power input one connection,
+V2-(SW) is for power input two connection.

Wall mount bracket x 2

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall­mounted bracket are included.

Connecting procedure

STEP 1 –
Take out 4 pin terminal block located in the included mounting kit package.
STEP 2 –
Connect power wire to +V1- or Connect +V2- (SW) as shown above
STEP 3 –
Plug into terminal block socket shown above. Polarity needs to match the V+ and V-

WARNING -- Always SHUTS OFF power source to connect power wire.
WARNING – any exceeded input voltage will not make this unit function and may damage this unit.

(SW)
+ V1 - + V2 -

Din Rail Bracket x 1

4 pin Terminal Block x1

5

Mode A Green LED ON -­For End-Span POE power 1,2,3,6

LED indicator

PW—Power 1, Power 2

NOTE:
Mode B Green LED is only for Mode B End-Span
model. with pin assignment 4,5,7,8. This LED will
not lit on for this model.

6

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE802.3af for POE
IEEE802.3at for POE+

Network Connector :

1xRJ-45 10/100/1000BaseT(X) Data
1xRJ-45 10/100/1000BaseT(X) Data with POE
Output power

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Protocol

CSMA/CD

LED

PW1(power 1) Green: ON- power good, OFF­power failed
PW2(power 2) Green: ON- power good, OFF­power failed
POE: ON- POE Normal working,
FLASH- Overload,
OFF- NO POE power detected

POE Pin Assignment

Mode A model, V+, V+, V-, V- for pin 1, 2, 3, 6

Reverse polarity protection

Present

Overload current protection

Present

Power Supply

2 Redundant power source
48V~56V VDC Power Input

Power Consumption

1 W@48 VDC full load, Without POE

POE power

Maximum POE power 36watts at 56VDC input

7

Removable Terminal Block

Provide 4 pin terminal block
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm

Operating Temperature

-40℃~75℃fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L X W X D)mm

103.5mmx32mmx81.5mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

Certifications:

EN55022/24

ITE equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,
CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

8

Housing Dimension