Level One IFS-0503 operation manual

Port Fast Ethernet Industrial Switch,

1 Port SC Single

Quick Installation Guide

LED Status

Description

10/100

/

Base-TX

Fiber

IFS-0503

5-

-Mode Fiber, 30km

Overview

The LevelOne IFS-0503 Industrial Fast Ethernet Switch
provides four ports at 10/100M TX and one single-mode fiber
port at 100M FX SC to enable high speed networks in mission­critical environments. With an industrial standard DIN-rail
mount, this switch can be installed in a cabinet, and clearly
visible status LEDs provide simple monitoring of port link
activity. The single-mode fiber port allows for large-scale
connections of up to 30km. The switch is housed in a solid
metal case rated at IP30, keeping it safe from dust, vibration,
heat and humidity, while an operational temperature range of ­40°C to +75°C makes it suitable for deployment in a lmost any
environment.

High Reliability

All components are built to withstand harsh environment
applications without compromise where humidity, temperature
variation and even shock vibration are concerns, including
Electric & Utility, Critical Infrastructure, Transportation and
Surveillance Security. This device operates under -40 to 75
Celsius (-40 to 167 Fahrenheit) temperature.

Plug & Play

This unmanaged Industrial Ethernet Switch is designed for the
demanding industrial environments at businesses in need of
instant connectivity with no setup or configure required, truly
plug and play.

Features

• Meets NEMA TS1/TS2 Environmental requirements such as temperature,
shock, and vibration for traffic control equipment

• Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for
industrial environment

• Supports 1024 MAC addresses. Provides 1M bits memory buffer

• Provides one Port SC Single-Mode Fiber with a maximum networking

range of 30km.

• Store-and-forward mechanism. Full wire-speed forwarding rate.

• Power Supply: 9~56VDC Terminal Block power input.

• 3.76W power consumption 48VDC full load

• -40℃ to 75℃ (-40℉ to 167℉) operating temperature range.

• Tested for functional operation @ -40℃ to 85℃ (-40℉ to 185℉).

• Metal case design and compliant with IP30 standard

Package Contents

 IFS-0503
 Din rail*1, wall mount*2, terminal block*1, screw*4
 Quick Installation Guide

v1.0

IFS-0503 Page 1

LED Status

PWR 1, 2

SW (relay)

LNK(1 ~ 4)

ON Power On
OFF Power Off
ON both PW1 and PW2 are connected
OFF only PW1 or PW2 is connected

ON TX link is detected
OFF TX port is not detected
Flashing TX port is active

IFS-0503 Page 2

ON FX fiber is detected

F5

IFS-0503 Page 3

OFF FX fiber is not detected
Flashing FX fiber is active

Power Input

+

–

+

–

Pin Standard Port

Uplink Port

PW1

PW2

Terminal Block

Relay Output

44–56VDC
Power Ground
44–56VDC
Power Ground
1A @ 24VDC

DIN Rail Mount

• Assembly: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place

• Start-up: Connect the supply voltage to start up the switch
via the terminal block (or DC JACK)

• Dismantling: Pull out the lower edge and then remove the
switch from the DIN rail.

IFS-0503 Page 4

10/100Base-TX Connector

The following lists the pin-out of 10/100Base-TX ports.

1 Output Transmit Data + Input Receive Data +
2 Output Transmit Data - Input Receive Data ­3 Input Receive Data + Output Transmit Data +
4 NC NC
5 NC NC
6 Input Receive Data - Output Transmit Data ­7 NC NC
8 NC NC

IFS-0503 Page 5

IFS-0503 Page 6