LevelOne IES-0843 User Manual

IES-0843

4 x 802.3at PoE + 3 FE + 1 MM SC Web Smart Switch -10 to 60C, DIN-rail

User Manual

v1.00 - 1206

2

Preface

This manual describes how to install and use the Industrial Web-Smart PoE & High Power PoE
Ethernet Switch. This switch introduced here is designed to deliver full scalability with web-based
management functions. Capable of operating at temperature extremes of -40°C to +75°C, this is
the switch of choice for harsh environments constrained by space.

Port 1 to port 4 on this switch supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing
Equipment (PSE) and can detect an IEEE802.3af compliant Powered Device (PD). Using external
48VDC power inputs through Terminal Block or Power Jack, data and power can be transmitted to
a Powered Device (PD) over the same twisted-pair Ethernet cable through port 1 to port 4 on the
switch.

Port 1 to port 4 on this switch also supports High Power PoE Power Sourcing Equipment (PSE) and
can detect a Powered Device (PD). Using external 55VDC power inputs through Terminal Block or
Power Jack, data and power can be transmitted to a Powered Device (PD) over the same twisted­pair Ethernet cable through port 1 to port 4 on the switch.

To get the most out of this manual, you should have an understanding of Ethernet networking
concepts.

In this manual, you will find:

 Features
 Illustrative LED functions
 Installation instructions
 Management Configuration
 Specifications

3

Table of Contents

OVERVIEW ........................................................................................................................... 4

INDUSTRIAL WEB-SMART POE ETHERNET SWITCH ............................................................................................. 4

FEATURES ............................................................................................................................................................... 5

PACKAGE CONTENTS ............................................................................................................................................. 5

FRONT PANEL DISPLAY .......................................................................................................................................... 6

POWER INPUT ........................................................................................................................................................ 7

DIN RAIN MOUNT ................................................................................................................................................. 8

10/100BASE-TX CONNECTOR ............................................................................................................................ 9

WEB MANAGEMENT ......................................................................................................... 10

DEFAULT SETTING ............................................................................................................................................... 10

LOGGING ON TO THE SWITCH ............................................................................................................................. 11

BROWSER INTERFACE .......................................................................................................................................... 12

PoE ............................................................................................................................................................. 13

HIGH POWER POE OPERATION .......................................................................................................................... 14

Port Based VLAN ..................................................................................................................................... 15

Priority....................................................................................................................................................... 16

Diff Serv Code Point ............................................................................................................................... 17

System Setup ........................................................................................................................................... 18

Firmware Upgrade ................................................................................................................................. 19

SPECIFICATIONS ............................................................................................................... 20

4

Overview

Industrial Web-Smart PoE Ethernet Switch

LevelOne IES-0843 Industry Ethernet Switch provides 4 PoE ports of 10/100Base-TX plus 3 ports of
10/100Base-TX Ethernet plus 1 port 100FX Multimode SC fiber to enable high speed network at
mission-critical environment. This device is designed to be mounted on an industry standard DIN­rail, plus the clearly visible status LEDs provide simple monitoring of port link activity.

Cost Effective

This device operates under -10 to 60 Celsius (-14 to 140 Fahrenheit) temperature that offers
optimal suitability for industrial applications at low cost while maintaining all components built to
withstand harsh environment applications without compromise reliability and stability.

Web Management

Web-based GUI management features implementation of Port-based VLAN, IEEE802.1p QoS,
Prioritised DSCP, set up Admin Password with ease. Plus, the Power over Ethernet ports can be On /
Off and limits the power budget remotely

Power over Ethernet

This switch is Power Sourcing Equipment (PSE), and it is fully complied with IEEE 802.3at PoE
standard at maximum 30W power budget per port. It helps to save infrastructure wiring costs
dramatically by eliminating electric wiring and less UPS needed. Also, it is compatible with
IEEE802.3af standard PD devices.

Safety

This device has been tested under UL508 standard for Industrial Control Equipment to endurance
under test turn on and off 6,000 times while loaded, wi
safety measurement to ensure field hardened, especially for the harsh environment.

5

Features

 Complies with EN61000-6-2 & EN61000-6-3 EMC Generic standard immunity for Industrial

environment.

 Manageable via Web browser interface.
 Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
 High Power PoE design up to 30W (enhancement of IEEE802.3af PoE).
 Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps-full/half-duplex; Auto

MDI/MDIX.

 100Base-FX: Multi mode SC or ST type, Single mode SC or ST type. 100Base-BX: WDM Single

mode SC type.

 Supports 1024 MAC addresses. Provides 1M bits memory buffer.
 Store-and-forward mechanism.
 Full wire-speed forwarding rate.
 Alarms for power and port link failure by relay output.
 PoE: Redundant 48VDC Terminal Block power inputs and 48VDC DC JACK power input for

15.4W per PoE port. Operating voltage and Max. current consumption: 1.5A @ 48VDC. Power
consumption: 72W Max.

 High Power PoE: Redundant 55VDC Terminal Block power inputs and 55VDC DC JACK power

input for 30W per High Power PoE port. Operating voltage and Max. current consumption: 2.3A
@ 55VDC. Power consumption: 130W Max.

 -10℃ to 60℃ (14℉ to 140℉) operating temperature range. Tested for functional operation @ -

20℃ to 70℃ (-4℉ to 158℉).

 Reset button on front panel.
 Front panel port status LEDs.
 Industrial aluminum case.
 Supports DIN-Rail, Panel, or Rack Mounting installation.

Package Contents

When you unpack the product package, you shall find the items listed below. Please inspect the
contents, and report any apparent damage or missing items immediately to your authorized
reseller.

 IES-0843 Industrial Web-Smart PoE Ethernet Switch
 Quick Installation Guide

 CD User Manual

6

Front Panel Display

LED

Status

Description

PW 1,2,3
Steady

Power On

Off

Power Off

10/100Base-TX or 100Base-FX/BX

LNK/ACT
Steady

Network connection is established

Flashing

Transmitting or Receiving data

PoE
(High Power)

Steady

Power Device (PD) is connected

Off

Power Device (PD) is disconnected

7

Power Input

Terminal Block

PW1

+

48VDC

Power Ground

PW2

+

48VDC

Power Ground

Earth Ground

Relay Output

0.1A @ 24VDC

*Warning signal disable for following:

1. The relay contact closes if Power1 and Power2 are both failed but Power3
on.

2. The relay contact closes if Power3 is failed but Power1 and Power2 are
both on.

DC Jack

PW3

DC Jack

48VDC

Special Note:

The relay output is normal open position when there is no power to the switch. Please do not
connect any power source to this terminal to prevent shorting your power supply.

8

DIN rain Mount

 Fix the DIN rail attachment plate to the back panel of the switch.
 Installation: Place the switch on the DIN rail from above using the slot. Push the front of the

switch toward the mounting surface until it audibly snaps into place.

 Removal: Pull out the lower edge and then remove the switch from the DIN rail.

9

10/100Base-TX Connector

Pin

PoE Port (1 to 4)

Standard Port (5)

1

Output Transmit Data +

Input Receive Data +

2

Output Transmit Data -

Input Receive Data -

3

Input Receive Data +

Output Transmit Data +

4

Positive (VCC+)

NC 5 Positive (VCC+)

NC 6 Input Receive Data -

Output Transmit Data -

7

Negative (VCC-)

NC 8 Negative (VCC-)

NC

The following lists the pin-out of 10/100Base-TX ports.

10

Web Management

The switch provides a browser interface that lets you configure and manage the switch remotely.

applications directly in your web browser by entering the IP address of the switch. You can then
use your web browser to list and manage switch configuration parameters from one central

Web-Based Browser Management

The switch provides a web-based browser interface for configuring and managing the switch. This
interface allows you to access the switch using a preferred web browser.

This chapter describes how to configure the switch using its web-based browser interface.

Default Setting

IP address: 192.168.1.10
User Name: admin
Password: [Blank]

11

Logging on to the switch

Switch IP Address
In your web browser, specify the IP address of the switch. Default IP address is 192.168.1.10.

User name
Enter the factory default user name: admin.

Password
Enter the factory default password (no password).
Or enter a user-defined password if you followed the instructions later and changed the factory
default password.

OK switch.

12

Browser Interface

The web browser interface provides groups of point-and-click buttons at the left field of the screen
for configuring and managing the switch.

 POE
 PORT BASED VLAN
 PRIORITY
 DIFF SERV CODE POINT

Bit 0 ~ 31, Bit 32 ~ 63

 SYSTEM SETUP
 FIRMWARE UPGRADE

13

PoE

PoE

1. System power budget: System power budget and type a new system power
budget.

2. OK: OK button to update your settings.

3. Enable mode: C Enable mode drop-down menu to choose Enable or Disable

Enable mode drop-down list to enable or disable Port 1 ~ Port 4 to discover Powered Device

(PD) connected to Port 1 ~ Port 4 of the Switch.

4. Power limit by classification: Check or uncheck Power limit by classification to enable or
disable Port 1 ~ Port 4 to provide power to PD according to classification of maximum power
range used by PD.

5. Fixed power limit(W): First uncheck Power limit by classification to disable Port 1 ~ Port 4 to
provide power to PD according to classification of maximum power range used by PD. Then
c Fixed power limit(W) fixed power limit for Port 1 ~ Port 4 to
provide power to PD.

6. Power priority: C Power priority drop-down menu to choose Low , Middle, or High

Power priority drop-down list to determine power priority of Port 1 ~ Port 4.

7. OK: OK button to update your settings.

14

High Power PoE Operation

This Industrial Web-Smart PoE & High Power PoE Ethernet switch is compliant with the 802.3af and

802.3at High Power standard, providing 30W of pure power to power demanding devices such as

pan-tilt-zoom (PTZ) network cameras, wireless access bridge/routers and large-screen network
video phones et cetera.

This 802.3af High Power switchs PoE operation with 802.3at based PD is highly versatile and
adaptable. Normally, when an 802.3at PD is connected to an 802.3af High Power compliant switch,
the switch will detect that the PDs power requirement is based on class 4 classification outlined in
the IEEE802.3at standard, and only attempt to provide 15.4W of power, which is insufficient to
power a 30W 802.3at PD. This is due to the reason that the 30W of power in 802.3af High Power is
classified as class 0. However, this 802.3af High Power switch can support 30W 802.3at PD by
setting the switch explicitly to provide a fixed rate of 30W power to 30W 802.3at PD.

Power limit by classification: Uncheck Power limit by classification to disable Port 1 ~ Port 4 to
provide power to 30W 802.3at PD according to classification of maximum power range used by PD.
Fixed power limit(W): C Fixed power limit(W) and type a new fixed power limit 30W
for Port 1 ~ Port 4 to provide power to 30W 802.3at PD.
OK: OK button to update your settings.

15

Port Based VLAN

Port Based VLAN

1. VLAN.1 ~ VLAN.7: Click and choose Port 1 ~ Port 8 to be added into VLAN.1 ~ VLAN.7.

2. Cancel: Cancel button to cancel your settings.

3. OK: OK button to update your settings.

16

Priority

Priority

1. Ratio Scheme: Click and choose All High Before Low, 10:1, 5:1 , or 2:1 ratio scheme.

2. Port 1 ~ Port 8: Click and choose TOS, 802.1p, or Port Priority ( High or Low ) for Port 1 ~
Port 8.

3. 802.1p Level 7 ~ Level 0: Click and set High or Low priority to queue of 802.1p Level 7 ~
Level 0.

4. Cancel: Cancel button to cancel your settings.

5. OK: OK button to update your settings.

17

Diff Serv Code Point

Diff Serv Code Point
Bit 0 ~ 31:

1. Diff Serv Code Point: Check and set Bit 0 ~ 31 of Diff Serv Code Point to high priority.

2. Cancel: Cancel button to cancel your settings.

3. OK: OK button to update your settings.

Bit 32 ~ 63:

1. Diff Serv Code Point: Check and set Bit 32 ~ 63 of Diff Serv Code Point to high priority.

2. Cancel: Cancel button to cancel your settings.

3. OK: OK button to update your settings.

18

System Setup

System Setup
System Configuration:

1. DHCP Client: Click and choose Enable or Disable to enable or disable the Switch as DHCP
client to be automatically supplied an IP address, gateway address, and subnet mask from
DHCP server.

2. IP Address: C IP Address text box and type a new address to change the IP Address.

3. Subnet Mask: C Subnet Mask text box and type a new address to change the Subnet
Mask.

4. Default Gateway: C Default Gateway text box and type a new address to change the
Default Gateway.

5. Cancel: Cancel button to cancel your settings.

6. OK: OK button to update your settings.

Password Configuration:

1. Old Password: Old Password and type in the old password.

2. New Password: New Password and type in a new password.

3. Confirm Again: Confirm Again text box. Type the same password in New Password
text box again to verify it.

4. Cancel: Cancel button to cancel your settings.

5. OK: OK button to update your settings.

System Reset/Restore to default:

1. Load Default: Load Default button to restore the default settings of the Switch.

2. Reset System: Reset System button to restart the Switch.

19

Firmware Upgrade

Firmware Update

1. Cancel: C Cancel button to cancel firmware update request.

2. Update: C Update button and wait for firmware update request being processed.

20

Specifications

Applicable Standards

IEEE802.3 10Base-T
IEEE802.3u 100Base-TX/FX

Switching Method

Store-and-Forward

Forwarding Rate

10Base-T
100Base-TX
100Base-FX/BX

10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
200Mbps full-duplex

Performance

14,880pps for 10Mbps
148,810pps for 100Mbps

Cable

10Base-T
100Base-TX
100Base-FX
100Base-BX

4-pair UTP/STP Cat. 3, 4, 5 Up to 100m (328ft)
4-pair UTP/STP Cat. 5 Up to 100m (328ft)
MMF (50

LED Indicators

Per unit Power status (Power1, Power2, Power3)
Per port
PoE & High Power PoE: PoE, Link/ACT
10/100TX, 100FX: Link/ACT

Dimensions

62mm (W) x 110mm (D) x 135mm (H)

Net Weight

1Kg (2.2lbs.)

Power Input

Terminal Block: 48, 55VDC (High Power)
DC Jack: 48, 55VDC (High Power)

Operating Voltage &
Max. Current
Consumption

PoE: 1.5A @ 48VDC
High Power PoE: 2.3A @ 55VDC

Power Consumption

PoE: 72W Max.
High Power PoE: 130W Max.

Operating
Temperature

-10°C to 60℃ (14℉ to 140℉)
Tested for functional operation @

-20℃ to 70℃ (-4℉ to 158℉)

Storage Temperature

-40°C to 85℃ (-40℉ to 185℉)

Humidity

5%-95% non-condensing

EMI

FCC Part 15, Class A
EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3

EMS

EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

Environmental Test
Compliance

IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)