LevelOne IES-0823 User Manual

User Manual

v1.00 - 1206

IES-0823

6 GE + 2 SFP Unmanaged Switc h -20 to 60C , DIN-rail

Preface

A member of the growing family of rugged switches, this switch addresses a need for a
smaller switch. This switch provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications. Capable of operating at temperature

extremes of -20°C to +60°C, this is the switch of choice for harsh environments constrained
by space.

Plug-and-Play Solution:
The switch is a plug-and-play Gigabit Ethernet Switch in compact size. It doesn't have any
complicated software to set up.

This manual desc r ibes how to install and use the Industrial Gigabit Ethernet Switch. This
switch integrates full wire speed switching technology. This switch brings the answer to
complicated Industrial networking environments.

To get the most out of this manual, you should have an understanding of Ethernet
networking concepts.

In this manual, you will find:

• Features on the switch

• Illustrative LED functions

• Installation instructions

• Specifications

IES-0823 User Manual Page 2

Table of Contents

PREFACE ........................................................................................................................................................... 2

PRODUCT OVERVIEW ....................................................................................................................................... 4

INDUSTRIAL GIGABIT ETHERNET SWITCH ...................................................................................................................... 4

PACKAGE CONTENTS ................................................................................................................................................ 4

PRODUCT HIGHLIGHTS ............................................................................................................................................. 5

FRONT PANEL DISPLAY ............................................................................................................................................. 6

PHYSICAL PORTS ..................................................................................................................................................... 6

INSTALLATION .................................................................................................................................................. 7

SELECTING A SITE FOR THE SWITCH ............................................................................................................................. 7

DIN RAIL MOUNTING .............................................................................................................................................. 8

WIRING DIAGRAM .................................................................................................................................................. 9

CONNECTING TO POWER ........................................................................................................................................ 10

CONNECTING TO YOUR NETWORK ............................................................................................................................ 12

SPECIFICATIONS ............................................................................................................................................. 13

APPENDIX A – CONNECTOR PINOUTS ............................................................................................................ 14

IES-0823 User Manual Page 3

Product Overview

Industrial Gi gab it Ethernet Switch

Package Contents

When you unpack the product package, you shall find the items listed below. Please
inspect the contents, and report any apparent damage or missing items immediately to
your authorized reseller.

• IES-0823
6 GE + 2 SFP Unmanaged Switch -20 to 60C, DIN-rail

• Quick Installation Guide

• CD User Manual

IES-0823 User Manual Page 4

Product Highlights

Basic Features

• Meets EN61000-6-2 & EN61000-6-3 EMC Generic Standard Immunity for industrial
environment.

• Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x.

• 1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex.

• Auto-Negotiation, Auto MDI/MDIX.

• 1000Base-SX/LX: Multi mode, Single mode SC type. 1000Base-BX: WDM Single mode

SC type.

• IEEE802.1p Queue Supports 4 priority queues.

• 8192 MAC addresses.

• 1.125M bits buffer memory.

• Full wire-speed forwarding rate.

• Supports jumbo frame up to 9K Bytes.

• Alarms for power failure by relay output.

• Power Supplies: Redundant 9-32VDC Terminal Block power inputs and 12VDC DC JACK

with 100-240VAC external power supply.

• Field Wiring T erminal: Use Copper Conductors Only, 60/75℃, 12-24 AWG torque value 7
lb-in.

• Operating voltage and Max. current consumption: 0.6A @ 12VDC, 0.3A @ 24VDC.

• Power consumption: 7.2W Max.

• -20℃ to 60℃ operating temperature.

• Industrial aluminum case.

• Supports DIN-Rail or Panel Mounting installation.

IES-0823 User Manual Page 5

Front Panel Display

•Power Status (PW1, PW2, PW3)

These LEDs come on when the switch is properly connected to power and turned on.

‚Port Status LEDs

The LEDs display status for each respe ctive port.

LED State Indication
10/100Base-TX

LNK/ACT

(Green)

1000Base-T/SX/LX/BX

LNK/ACT

(Orange)

Steady A valid network connection established.

Flashing

Steady A valid network connection established.
Flashing

Transmitting or receiving da ta.
ACT stands for ACTIVITY.

Transmitting or receiving da ta.
ACT stands for ACTIVITY.

Physical Ports

This switch provides:

Eight 10/100/1000Base-TX ports
Seven 10/100/1000Base-TX por ts + one combo port
Six 10/100/1000Base-TX ports + two combo ports

<Note> Combo port: Either 1000Base-SX/LX port or 10/100/1000Base-TX port.
Connectivity

RJ-45 connectors
SC connector on 1000Base-SX/LX/BX fiber port

IES-0823 User Manual Page 6

Installation

This chapter gives step-by-step instructions about how to install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch where it will not be subjected to
extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you
select should meet the following requirements:

• The ambient temperature should be between -20 to 60 degrees Celsius.

• The relative humidity should be less than 95 percent, non-condensing.

• Surrounding electrical devices should not exceed the electromagnetic field (RFC)

standards.

• Make sure that the switch receives adequate ventilation. Do not block the ventilation
holes on the switch

• The power outlet should be within 1.8 meters of the switch.

IES-0823 User Manual Page 7

DIN Rail Mounting

Fix the DIN rail attachment plate to the back panel of the switch.
Installation: Place the switch on the DIN rail from above using the slot. Push the front of

the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch from the DIN rail.

IES-0823 User Manual Page 8

Wiring Diagram

IES-0823 User Manual Page 9

Connecting to Power

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs can be used to power up this device. You only need to
have one power input connected to run the switch.

Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and
then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the switch.

12VDC DC Jack

Step 1: Connect the supplied AC to DC power adapter to the receptacle on the topside of
the switch.

Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a
standard AC outlet with the appropriate AC voltage.

IES-0823 User Manual Page 10

Alarms for Power Failure

Step 1: There are two pins on the terminal block are used for power failure detection. It
provides the normally closed output when the power source is active. Use this as a dry
contact application to send a signal for power failure detection.

Power Input Assignment
Power3 12VDC ,3A DC Jack

＋

Power2

Power1

Relay Output Rating 30 VDC, 1A
Relay Alarm Assignment

FAULT

Special note:
The relay output is normal open position when there is no power to the switch.
Please do not connect any power source to this terminal to prevent the shortage to
your power supply.

1.5A@24VDC(9-32VDC)

－

Power Ground

＋

1.5A@24VDC(9-32VDC)

－

Power Ground
Earth Ground

*Warning signal disable for following:
The relay contact closes if Power1 and Power2 are
both failed but Power3 on.
The relay contact closes if Power3 is failed but
Power1 and Power2 are both on.

Terminal Block

IES-0823 User Manual Page 11

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the switch to your
network. Use appropriate cables that meet your speed and cabling requirements.

Cable Specifications

Speed Connector Port Speed

Half/Full Duplex

10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP Cat. 3, 4, 5 100 m
100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP Cat. 5 100 m
1000Base-T RJ-45 2000 Mbps 4-pair UTP/STP Cat. 5, 5e 100 m
1000Base-SX SC 2000 Mbps MMF (50 or 62.5μm) 550 m
1000Base-LX SC 2000 Mbps SMF (9 or 10μm) 10, 20, or 50 km
1000Base-BX SC 2000 Mbps SMF (9 or 10μm) 20 km

Cabling

Cable Max.

Distance

Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a

straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on connectors and

speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired

device.
Step 5: Once the connections between two end devices are made successfully, turn on

the power and the switch is operational.

IES-0823 User Manual Page 12

Specifications

Forwarding Rate

Performance

148,80pps for 10Mbps

Cable

Operating V oltage &

EMI

EMS

Industrial Gigabit Ethernet Switch

Applicable Standards IEEE802.3 10Base-T

Switching Method

10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX/BX:

10Base-T:
100Base-TX:
1000Base-T:

1000Base-SX/LX/BX:

LED Indicators

Dimensions

Net Weight

Power T erm inal Blo ck: 9-32VDC

Max. Current Consumption
Power Consumption
Operating Temperature
Storage T empera ture
Humidity
Safety

Environmental Test
Compliance

IES-0823 User Manual Page 13

10/100/1000Base-TX auto-negotiating ports with RJ-45
connectors
1000Base-SX/LX/BX fiber ports

IEEE802.3u 100Bas e-TX
IEEE802.3ab 1000Base-T
IEEE802.3z 1000Base-SX/LX

Store-and-Forward

10 / 20Mbps Half / Full-duplex
100 / 200Mbps Half / Full-duplex
2000Mbps Full-duplex
2000Mbps Full-duplex

148,810pps for 100Mbps
1,488,100pps for 1000Mbps

2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5, 5e
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)

Per unit –

Power status (Power1, Power2, Power3)

Per port –

10/100Base-TX - Link/ACT (Green)
10/100/1000Base-TX or
1000Base-SX/LX/BX - Link/ACT (Orange)

58mm (W) × 110mm (D) × 135mm (H)
(2.29” (W) × 4.33” (D) × 5.31” (H))

0.8Kg (1.76lbs.)

DC Jack: 12VDC, External AC/DC required

0.6A @ 12VDC, 0.3A @ 24VDC

7.2W Max.

-20℃ to 60℃ (-4℉ to 140℉)

-40℃ to 85℃ (-40℉ to 185℉)
5%-95% non-condensing
UL508
FCC Part 15, Class A

EN61000-6-3:
EN55022, EN61000-3-2, EN61000-3-3

EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Stan dards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)

Appendix A – Connector Pinouts

Pin arrangement of RJ-45 connectors:

RJ-45 Connector and Cable Pi ns

The following table lists the pinout of 10/100/1000Base-TX ports.

Pin

1 TP0＋
2 TP0－
3 TP1＋
4 TP2＋
5 TP2－
6 TP1－
7 TP3＋
8 TP3－

Ports

IES-0823 User Manual Page 14