Page 1
User Manual
v1.00 - 1206
IES-0510
4 FE + 1 MM SC Unmanaged Switc h -10 to 60, DIN-rail
Page 2
Preface
A member of the growing family of rugged switches, this switch addresses a need for a
smaller switch. This switch pro vides an affordable solutio n for rugged and outdoor
environment, transportation road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications. Capable of operating at temperature
extremes of -10°C to +60°C, this is the switch of choice for harsh environments constrained
by space.
Plug-and-Play Solution:
The switch is a p lug-and-play Fast Ethernet Switch in compact size. It doesn't have any
complicated software to set up.
This manual desc r ibes how to install and use the Industrial compact Ethernet Switch. This
switch integrates full wire speed switching technology. This switch brings the answer to
complicated Industrial networking environments.
To get the most out of this manual, you should have an understanding of Ethernet
networking concepts.
In this manual, you will find:
• Features on the switch
• Illustrative LED functions
• Installation instructions
• Specifications
IES-0510 User Manual Page 2
Page 3
Table of Contents
PREFACE ........................................................................................................................................................... 2
PRODUCT OVERVIEW ....................................................................................................................................... 4
INDUSTRIAL ETHERNET SWITCH .................................................................................................................................. 4
PACKAGE CONTENTS ................................................................................................................................................ 4
PRODUCT HIGHLIGHTS ............................................................................................................................................. 5
FRONT PANEL DISPLAY ............................................................................................................................................. 6
PHYSICAL PORTS ..................................................................................................................................................... 6
INSTALLATION .................................................................................................................................................. 7
SELECTING A SITE FOR THE SWITCH ............................................................................................................................. 7
DIN RAIL MOUNTING .............................................................................................................................................. 7
CONNECTING TO POWER .......................................................................................................................................... 8
CONNECTING TO YOUR NETWORK .............................................................................................................................. 9
SPECIFICATIONS ............................................................................................................................................. 11
APPENDIX A – CONNECTOR PINOUTS ............................................................................................................ 12
IES-0510 User Manual Page 3
Page 4
Product Overview
Industrial Ethernet Switch
Package Contents
When you unpack the product package, you shall find the items listed below. Please
inspect the contents, and report any apparent damage or missing items immediately to
your authorized reseller.
• IES-0510
4 FE + 1 MM SC Unmanaged Switch -10 to 60, DIN-rail
• Quick Installation Guide
• CD User Manual
IES-0510 User Manual Page 4
Page 5
Product Highlights
Basic Features
• 5-port 10/100Base-TX, 4-port 10/100Base-TX plus 1-port 100Base-FX, or 1-port
10/100Base-TX plus 1-port 100Base-FX.
• Available in media converter format with 1-port 10/100Base-TX and 1-port 100Base-FX.
• Support IEEE802.3/802.3u/802.3X.
• Auto-negotiation: 10/100Mbps, Full/half-duplex; Auto MDI/MDIX.
• Support 2048 MAC addresses, 384K bits buffer memory.
• Store-and-forward mechanism.
• Full wire-speed forwarding rate and non-blocking mechanism.
• Broadcast storm filtering.
• Operating voltage and Max. current consumption: 0.2A @ 12VDC, 0.1A @ 24VDC,
0.05A @ 48VDC.
• Power consumption: 2.4W Max.
• Power Su pply: DC Terminal Block power input, 12-48VDC with polarity protection.
• Plastic compact DIN-Rail Industrial case design.
• DIN-Rail mounting ability.
IES-0510 User Manual Page 5
Page 6
Front Panel Display
•Power Status (PWR)
This LED comes on when the switch is properly connected to power and turned on. ‚Port Status LEDs
The LEDs display status for each respective port.
LED State Indication
10/100TX or 100FX
A valid network connection established.
LNK stands for LINK.
Transmitting or receiving da ta.
ACT stands for ACTIVITY.
Light solid yellow for a port transferring at
100Mbps.
The port is tra nsferr in g at 10M bps I f this L ED is
dark.
LNK/ACT
(Green)
100
(Yellow)
Steady
Flashing
Steady
Off
Physical Ports
This switch provides:
Five 10/100Base-TX ports
Four 10/100Base-TX ports + one 100Base-FX port
One 10/100Base-TX port + one 100Base-FX port
Connectivity
RJ-45 connectors
SC or ST connector on 100Base-FX fiber port
IES-0510 User Manual Page 6
Page 7
Installation
This chapter gives step-by-step instructions about how to install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch where it will not be subjected to
extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you
select should meet the following requirements:
• The ambient temperature should be between -10 to 60 degrees Celsius.
• The relative humidity should be less than 95 percent, non-condensing.
• Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.
• Make sure that the switch receives adequate ventilation. Do not block the ventilation
holes on each side of the switch
• The power outlet should be within 1.8 meters of the switch.
DIN Rail Mounting
Installation: Place the switch on the DIN rail from above using the slot. Push the front of
the switch toward the mounting surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch from the DIN rail.
IES-0510 User Manual Page 7
Page 8
Connecting to Power
DC Terminal Block Power Inputs
Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and
then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.
The T erminal Block
PWR Power Input
GND Power Ground
Earth Ground
IES-0510 User Manual Page 8
Page 9
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the switch to your
network. Use appropriate cables that meet your speed and cabling requirements.
Cable Specifications
Speed Connector Port Speed
Half/Full
Duplex
10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP Cat. 3, 4, 5 100 m
100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP Cat. 5 100 m
100Base-FX SC, ST 100/200 Mbps MMF (50 or 62.5μm) 2 km
100Base-FX SC, ST 100/200 Mbps SMF (9 or 10μm) 15, 40, or 75 km
Cable Max.
Distance
IES-0510 User Manual Page 9
Page 10
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a
straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on connectors and
speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired
device.
Step 5: Once the connections between two end devices are made successfully, turn on
the power and the switch is operational.
IES-0510 User Manual Page 10
Page 11
Specifications
Humidity
5%-95% non-condensing
Industrial Compact Switch 10/100Base-TX auto-negotiating ports with RJ-45 connectors,
100Base-FX fiber ports
Applicable Standa rd s IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX
Switching Method
Forwarding Rate
10Base-T:
100Base-TX/FX:
Performance
Cable
10Base-T:
100Base-TX:
100Base-FX:
LED Indicator s
Dimensions
Net Weight
Power Terminal Block: 12-48VDC
Operating Voltage &
Max. Current
Consumption
Power Consumption
Operating Temperature
Storage Temperature
Store-and-Forward
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
148,80pps for 10Mbps
148,810pps for 100Mbps
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
Per unit – Power status (PWR)
Per port – 10/100TX or 100FX -
LNK/ACT (Green), 100 (Yellow)
26mm (W) × 70mm (D) × 110mm (H)
(1.02” (W) × 2.76” (D) × 4.33” (H))
0.2Kg (0.44lb.)
0.2A @ 12VDC, 0.1A @ 24VDC, 0.05A @ 48VDC
2.4W Max.
-10℃ to 60℃ (14℉ to 140℉)
-25℃ to 85℃ (-13℉ to 185℉)
Safety
EMI
EMS
Environmental Test
Compliance
UL60950-1, EN60950-1, IEC60950-1
FCC Part 15, Class A
EN61000-6-3:
EN55022, EN61000-3-2, EN61000-3-3
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
EN61000-4-11 (Voltage Dips Standards)
IEC60068-2-6 Fc (Vibration Re sistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)
IES-0510 User Manual Page 11
Page 12
Appendix A – Connector Pinouts
RJ-45 Connector and Cable Pins
The following table lists the pinout of 10/100Base-TX ports.
Pin Regular Ports Uplink port
1 Output Transmit Data + Input Receive Data +
2 Output Transmit Data - Input Receive Data 3 Input Receive Data + Output Transmit Data +
4 NC NC
5 NC NC
6 Input Receive Data - Output Transmit Data 7 NC NC
8 NC NC
IES-0510 User Manual Page 12
Loading...