Level One GSW-0809 operation manual

LevelOne

User Manual

GSW-0509 / GSW-0809

5/8-Port Gigabit Switch w/ Internal Power

V1.0

FCC Certifications

This Equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to pro vide reasonable protection ag ainst
harmful interference when the equipment is operated in a
commercial environment. This equipm ent gener ates, u ses, and c an
radiate radio frequency energ y and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a r esidential area is lik ely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.

This device complies with Part 1 5 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.

CE Marking Warning

This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE, the
essential protection requirement of Council Directive 89/336/EEC on
the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of up grading its products and it
may be possible that information in this docum ent is not up-t o-date.
Please check with your local distribut ors for the latest information.
No part of this document can be copied or reproduced in an y form
without written consent from the company.

Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright © 2008, All Rights Reserved.

2

Introduction

The device is a powerful, high-performance Gigabit Ethernet switch,
with all ports capable of 10, 100 or 1000Mbps auto-negotiation
operation (NWay), which means the switch could automatically
negotiate with the connected partners on the n etwork speed and
duplex mode. It is ideal for micro- segmenting large networks into
smaller, connected subnets for improved performanc e, enabling the
bandwidth demanding multimedia and imaging applications.
Moreover, the 10/100/1000Mbps auto-sensing ability provides an
easy way to migrate 10/100Mbps to 1000Mbps network with no pain.
Compared to the shared 10Mbps or 100Mbps networks , the switch
delivers a dedicated 10/100/1000Mbps connection to every attached
client with no bandwidth congestion issue. This switch also supports
auto MDI / MDI-X function. Each p ort could be used t o connect to
another switch or hub with no crossover RJ-45 cable.

Store-and-forward switching mode promises the low latency plus
eliminates all the network errors, including runt and CRC error
packets. To work under full-duplex mode, transmission and
reception of the frames can occur s imultaneously without causing
collisions as well as double the network bandwidth.

The switch provides 9K bytes jumbo frames, which means the
frames size is larger than normal 1.5K. With the Jumbo frame
function, you can get better network performance, because the
switch can send more data at the same time.

The switch is plug-n-play without an y software to c o nf ig ure an d also
fully compliant with all kinds of network protocols.

Before you start to install the switch, chec k the f ollo wing c ontents in
this package：

z GSW-0509/GSW-0809 Switch
z One power cord
z User’s manual

3

LED Definition

GSW-0509 Front Panel

GSW-0809 Front Panel

LED Status Operation

Steady Green Power is on

Power

Off Power is off
Steady Green Port connected

Link/ACT

Blinking Green The port is transmitting/receiving data

Rear Panel

The rear panel of the GSW-0509/GSW-0809 switch consists
of a DC power connector and 5/8 10/100/1000Mbps RJ45
Ports. The following figure shows the rear panel of the Switch.

y GSW-0509

y GSW-0809

4

Stations Connection

Connect each station to the switch by twisted-pair cable. Plug
one RJ-45 connector into a RJ-45 port of the switch, and plug
the other RJ-45 connector into the station’s network adapter.
Power on the switch and then system is ready.
For cable selection, refer to the following table.

Switches Connection

In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As all
the ports support auto MDI / MDI-X function, using a straight
cable to make a switch-to-switch connection is allowed.
For cable selection, refer to the following table：

Network Speed Cable Type Max. Length

10Mbps Cat. 3, 4, 5 UTP/STP 100 meters

100Mbps Cat. 5 UTP/STP 100 meters

1000Mbps Cat. 5e/6 UTP/STP 100 meters

5

Specification

Standard y IEEE 802.3 10BASE-T

Interface y 5/8 * 10/100/1000Mbps RJ-45 Gigabit Ethernet

y IEEE 802.3u 100BASE-TX
y IEEE 802.3ab 1000BASE-T
y IEEE 802.3x Full Duplex Operation & Flow

Control

Ports (GSW-0509/GSW-0809)

NWay Protocol
Support

MAC Address
Table

Buffer Memory y 104KBytes (GSW-0509)

Jumbo Frame y 9K Byte (GSW-0509/GSW-0809)

Power Supply y Internal Power Supply 100-240 VAC 5V/2A

Temperature y Operating Temperature: 0 40~℃℃

Humidity y Operating Humidity: 10%~90% (non-condensing)

EMI y CE and FCC class A

y 10Mbps: Full/Half duplex
y 100Mbps: Full/Half duplex
y 1000Mbps: Full duplex only
y 1K MAC Address entries (GSW-0509)
y 4K MAC Address entries (GSW-0809)

y 128KBytes (GSW-0809)

y Storage Temperature : -10Ԩ~70Ԩ

y Storage Temperature: 5%~95%

6

Technical Support

Thank you for selecting LevelOne products. LeveOne’s
website contains the latest user documentation and soft-ware
updates for LevelOne products.
Please contact LevelOne Technical Support through our
website.

World Wide Web

http://global.level1.com/

7