Level One GEP-2682 User Manual
LevelOne
GEP-2681
GEP-2682
User’s Manual
i
26-Port L3 Lite Managed Gigabit PoE Switch
GEP-2681/GEP-2682
User's Manual
26-Port L3 Lite Managed Gigabit PoE Switch
Release 6.33
2016, Digital Data Communications GmbH, Germany. All rights reserved. All brand and product names are
trademarks or registered trademarks of Digital Data companies
ii
About This Manual
Copyright
Copyright © 2016 Digital Data Communications GmbH. All rights reserved.
The products and programs described in this User’s Manual are licensed products of Manufacture
Technology, This User’s Manual contains proprietary information protected by copyright, and this
User’s Manual and all accompanying hardware, software and documentation are copyrighted. No
parts of this User’s manual may be copied, photocopied, reproduced, translated or reduced to any
electronic medium or machine-readable from by any means by electronic or mechanical. Including
photocopying, recording, or information storage and retrieval systems, for any purpose other than
the purchaser’s personal use, and without the prior express written permission of Manufacture
Technology.
.
Purpose
This manual gives specific information on how to operate and use the management functions of
the GEP-2681/GEP-2682
Audience
The Manual is intended for use by network administrators who are responsible for operating and
maintaining network equipment; consequently, it assumes a basic working knowledge of general
switch functions, the Internet Protocol (IP), and Simple Network Management Protocol (SNMP).
CONVENTIONS
The following conventions are used throughout this manual to show information.
WARRANTY
See the Customer Support/ Warranty booklet included with the product. A copy of the specific
warranty terms applicable to your Manufacture products and replacement parts can be obtained
from your Manufacture Sales and Service Office authorized dealer.
Disclaimer
Manufacture Technology does not warrant that the hardware will work properly in all
environments and applications, and marks no warranty and representation, either implied or
expressed, with respect to the quality, performance, merchantability, or fitness for a particular
purpose. Manufacture disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a
commitment on the part of Manufacture. Manufacture assumes no responsibility for any
inaccuracies that may be contained in this User’s Manual. Manufacture makes no commitment to
update or keep current the information in this User’s Manual, and reserves the righter to make
improvements to this User’s Manual and /or to the products described in this User’s Manual, at
any time without notice.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the Instruction manual, may cause harmful interference to radio
communications.
FCC Caution
To assure continued compliance (example-use only shielded interface cables when connection
to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CE mark Warning
This is a Class B device, In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
ii
NOTE: Emphasizes important information or calls your attention to
related features or instructions.
WARNING: Alerts you to a potential hazard that could cause personal
injury.
CAUTION: Alerts you to a potential hazard that could cause loss of
data, or damage the system or equipment.
iv
Table of Contents
Revision History ............................................................................................................................................... x
INTRODUCTION .......................................................................................................................... 1
CHAPTER 1 OPERATION OF WEB-BASED MANAGEMENT ................................ 2
CHAPTER 2 SYSTEM CONFIGURATION ................................................................... 6
2-1 System .................................................................................................................................................... 6
2-1.1 Information ............................................................................................................................................. 6
2-1.2 IP .............................................................................................................................................................. 7
2-1.3 NTP ........................................................................................................................................................ 10
2-1.4 Time ................................................................................................................................................ 11
2-1.5 Log ......................................................................................................................................................... 14
2-2 Green Ethernet ..................................................................................................................................... 14
2-3 Ports Configuration ............................................................................................................................ 18
2-3.1 Ports ...................................................................................................................................................... 18
2-3.2 Ports Description ................................................................................................................................. 21
2-4 DHCP ...................................................................................................................................................... 22
2-4.1 Server .................................................................................................................................................... 22
2-4.1.1 Mode ............................................................................................................................................. 22
2-4.1.2 Excluded IP.................................................................................................................................... 24
2-4.1.3 Pool ....................................................................................................................................................... 25
2-4.2 Snooping .............................................................................................................................................. 27
2-4.3 Relay ...................................................................................................................................................... 29
2-5 Security ................................................................................................................................................. 31
2-5.1 Switch .................................................................................................................................................... 31
2-5.1.1 Users .............................................................................................................................................. 31
2-5.1.2 Privilege Level ............................................................................................................................... 33
2-5.1.3 Authentication Method ............................................................................................................... 35
2-5.1.4 SSH ................................................................................................................................................ 36
2-5.1.5 HTTPs ............................................................................................................................................. 37
2-5.1.6 Access Management ................................................................................................................... 38
2-5.1.7 SNMP ............................................................................................................................................. 40
2-5.1.8 RMON ............................................................................................................................................ 54
2-5.2 Network ................................................................................................................................................ 61
2-5.2.1 Limit Control ................................................................................................................................. 61
2-5.2.2 NAS ................................................................................................................................................ 64
2-5.2.3 ACL ................................................................................................................................................. 72
2-5.2.4 IP Source Guard ........................................................................................................................... 79
2-5.2.5 ARP Inspection ............................................................................................................................. 83
2-5.3 AAA ........................................................................................................................................................ 91
2-5.3.1 RADIUS .......................................................................................................................................... 91
2-5.3.2 TACACS+ ..................................................................................................................................................... 94
2-6 Aggregation ......................................................................................................................................... 96
2-6.1 Static ...................................................................................................................................................... 96
2-6.2 LACP ...................................................................................................................................................... 98
v
2-7 Loop Protection ................................................................................................................................. 100
2-8 Spanning Tree ................................................................................................................................................. 102
2-8.1 Bridge Setting .................................................................................................................................... 102
2-8.2 MSTI Mapping .................................................................................................................................... 105
2-8.3 MSTI Priorities .................................................................................................................................... 107
2-8.4 CIST Ports ............................................................................................................................................ 108
2-8.5 MSTI Ports .......................................................................................................................................... 111
2-9 IPMC Profile ....................................................................................................................................... 113
2-9.1 Profile Table ...................................................................................................................................................... 113
2-9.1.1 IPMC Profile Rule Settings Table ........................................................................................................ 114
2-9.2 Address Entry ..................................................................................................................................... 116
2-10 MVR.................................................................................................................................................... 118
2-11 IPMC .................................................................................................................................................. 121
2-11.1 IGMP Snooping ................................................................................................................................ 121
2-11.1.1 Basic Configuration ................................................................................................................. 121
2-11.1.2 VLAN Configuration ................................................................................................................ 124
2-11.1.3 Port Filtering Profile................................................................................................................. 126
2-11.2 MLD Snooping ................................................................................................................................. 128
2-11.2.1 Basic Configuration ................................................................................................................. 128
2-11.2.2 VLAN Configuration ................................................................................................................ 131
2-11.2.3 Port Group Filtering ................................................................................................................. 133
2-12 LLDP .................................................................................................................................................. 134
2-12.1 LLDP Configuration ......................................................................................................................... 134
2-12.2 LLDP-MED Configuration ............................................................................................................... 138
2- 13 PoE ................................................................................................................................................... 145
2- 13.1 Configuration .................................................................................................................................. 145
2- 13.2 Power Delay .................................................................................................................................... 148
2- 13.3 Scheduling ....................................................................................................................................... 149
2- 13.4 Auto Checking ................................................................................................................................ 151
2-14 MAC Table...................................................................................................................................................... 153
2-15 VLANs ............................................................................................................................................... 156
2-16 Private VLANs .................................................................................................................................. 160
2-16.1 VLAN Membership .......................................................................................................................... 160
2-16.2 Port Isolation .................................................................................................................................... 162
2-17 VCL .................................................................................................................................................... 163
2-17.1 MAC-based VLAN ............................................................................................................................ 163
2-17.2 Protocol -based VLAN .................................................................................................................... 165
2-17.2.1 Protocol to Group .................................................................................................................... 165
2-17.2.2 Group to VLAN ......................................................................................................................... 167
2-17.3 IP Subnet-based VLAN ................................................................................................................... 168
2-18 VOICE VLAN ..................................................................................................................................... 170
2-18.1 Configuration ................................................................................................................................... 170
2-18.2 OUI .................................................................................................................................................... 172
2-19 QoS .................................................................................................................................................... 173
vi
2-19.1 Port Classification ............................................................................................................................ 173
2-19.2 Port Policing ..................................................................................................................................... 176
2-19.3 Port Schedulers ................................................................................................................................ 178
2-19.4 Port Shaping ..................................................................................................................................... 181
2-19.5 Port Tag Remarking ......................................................................................................................... 184
2-19.6 Port DSCP ......................................................................................................................................... 187
2-19.7 DSCP-Based QoS ............................................................................................................................. 189
2-19.8 DSCP Translation ............................................................................................................................. 191
2-19.9 DSCP Classification .......................................................................................................................... 193
2-19.10 QoS Control List Configuration ................................................................................................... 195
2-19.11 Storm Control ................................................................................................................................. 200
2-20 Mirror ................................................................................................................................................ 201
2-21 UPnP ................................................................................................................................................. 203
2-22. GVRP ................................................................................................................................................ 205
2-22.1 Global Config ................................................................................................................................... 205
2-22.2 Port Config ....................................................................................................................................... 207
2-23. sFlow ................................................................................................................................................ 208
2-24 Switch2go ........................................................................................................................................ 211
2-24.1 Switch2go setting ............................................................................................................................ 211
2-24.2 User Link Management ................................................................................................................... 213
2-24.3 Port Name Service ........................................................................................................................... 214
2-25 SMTP Configuration ....................................................................................................................... 215
CHAPTER 3. MONITOR ................................................................................. 217
3-1 System ................................................................................................................................................ 217
3-1.1 Information ......................................................................................................................................... 217
3-1.2 IP Status .............................................................................................................................................. 220
3-1.3 Log ....................................................................................................................................................... 222
3-1.4 Detailed Log ....................................................................................................................................... 224
3-2 Green Ethernet ................................................................................................................................... 225
3-2.1 Port Power Savings ............................................................................................................................ 225
3-3 Ports .................................................................................................................................................... 226
3-3.1 Traffic Overview ................................................................................................................................. 226
3-3.2 Qos Statistics ...................................................................................................................................... 228
3-3.3 QCL Status .......................................................................................................................................... 230
3-3.4 Detailed Statistics .............................................................................................................................. 232
3-3.5 SFP Information ................................................................................................................................. 236
3-4 DHCP ................................................................................................................................................... 238
3-4.1 Server .................................................................................................................................................... 238
3-4.1.1 Statistics ..................................................................................................................................... 238
3-4.1.2 Binding ........................................................................................................................................ 239
3-4.1.3 Declined IP ................................................................................................................................. 240
3-4.1 Snooping Table ................................................................................................................................................ 240
3-4.2 Relay Statistics .................................................................................................................................... 242
3-4.3 Detailed Statistics .............................................................................................................................. 243
3-5 Security ............................................................................................................................................... 245
vii
3-5.1 Access Management Statistics ......................................................................................................... 245
3-5.2 Network .............................................................................................................................................. 246
3-5.2.1 Port Security ............................................................................................................................... 246
3-5.2.2 NAS .............................................................................................................................................. 251
3-5.2.3 ARP Inspection ........................................................................................................................... 258
3-5.2.4 IP Source Guard ......................................................................................................................... 259
3-5.3 AAA ...................................................................................................................................................... 261
3-5.3.1 RADIUS Overview ....................................................................................................................... 261
3-5.3.2 RADIUS Details ........................................................................................................................... 263
3-5.4 Switch .................................................................................................................................................. 268
3-5.4.1 RMON .......................................................................................................................................... 268
3-6 LACP .................................................................................................................................................... 277
3-6.1 System Status ..................................................................................................................................... 277
3-6.2 Port Status .......................................................................................................................................... 278
3-6.3 Port Statistics ...................................................................................................................................... 280
3-7 Loop Protection ................................................................................................................................. 282
3-8 Spanning Tree ................................................................................................................................................. 283
3-8.1 Bridge Status ...................................................................................................................................... 283
3-8.2 Port Status .......................................................................................................................................... 285
3-8.3 Port Statistics ...................................................................................................................................... 287
3-9 MVR ..................................................................................................................................................... 289
3-9.1 Statistics .............................................................................................................................................. 289
3-9.2 MVR Channels Groups ...................................................................................................................... 291
3-9.3 MVR SFM Information....................................................................................................................... 293
3-10 IPMC .................................................................................................................................................. 295
3-10.1 IGMP Snooping ................................................................................................................................ 295
3-10.1.1 Status ................................................................................................................................................ 295
3-10.1.2 Group Information ................................................................................................................... 297
3-10.1.3 IPv4 SFM Information .............................................................................................................. 299
3-10.2 MLD Snooping ................................................................................................................................. 301
3-10.2.1 Status ................................................................................................................................................ 301
3-10.2.2 Group Information ................................................................................................................... 303
3-10.2.3 IPv6 SFM Information .............................................................................................................. 306
3-11 LLDP .................................................................................................................................................. 308
3-11.1 Neighbour ........................................................................................................................................ 308
3-11.2 LLDP-MED Neighbour..................................................................................................................... 310
3-11.3 PoE ............................................................................................................................................................ 313
3-11.4EEE ...................................................................................................................................................... 315
3-11.5 Port Statistics.................................................................................................................................... 317
3-12 PoE Statistics .................................................................................................................................... 319
3-13 MAC Table...................................................................................................................................................... 321
3-14 VLANs ............................................................................................................................................... 323
3-14.1 VLAN Membership .......................................................................................................................... 323
3-14.2 VLAN Port ......................................................................................................................................... 325
3-15 VCL .................................................................................................................................................... 327
3-15.1 MAC-based VLAN ............................................................................................................................ 327
viii
3-15.2 Protocol-based VLAN ..................................................................................................................... 328
3-15.2.1 Protocol to Group .................................................................................................................... 328
3-15.2.2 Group to VLAN ......................................................................................................................... 330
3-15.3 IP Subnet-based VLAN ................................................................................................................... 331
3-16 sFlow ................................................................................................................................................. 332
CHAPTER 4. DIAGNOSTICS ......................................................................... 334
4-1 Ping ..................................................................................................................................................... 334
4-2 Ping6 ................................................................................................................................................... 336
4-3 VeriPHY ............................................................................................................................................... 338
4-4 Traceroute .......................................................................................................................................... 339
CHAPTER 5. MAINTENANCE ...................................................... 340
5-1 Restart Device .................................................................................................................................... 340
5-2 Factory Defaults ................................................................................................................................ 342
5-3 Software ............................................................................................................................................. 343
5-3.1 Download ........................................................................................................................................... 343
5-3.2 Software Image Select ...................................................................................................................... 345
5-4 Configuration .................................................................................................................................... 347
5-4.1 Save startup-config ........................................................................................................................... 347
5-4.2 Upload ................................................................................................................................................. 348
5-4.3 Download ........................................................................................................................................... 350
5-4.4 Activate ............................................................................................................................................... 352
5-4.5 Delete .................................................................................................................................................. 353
CHAPTER 6 DMS-MANAGEMENT ................................................................................ 354
6-1 Information ........................................................................................................................................ 354
6-2 Device List .......................................................................................................................................... 356
CHAPTER 7 DMS-GRAPHIC MONITORING ............................................................... 358
7-1 Topology View ................................................................................................................................... 358
7-2 Floor View .......................................................................................................................................... 361
7-3 Map View ............................................................................................................................................ 362
CHAPTER 8 DMS-MAINTENANCE................................................................................ 363
8-1 Floor Image ........................................................................................................................................ 363
8-2 Trouble shooting ............................................................................................................................... 364
8-3 Traffic Chart ....................................................................................................................................... 365
x
Revision History
Release
Date
Revision
V6.33
08/1/2016
A1
1
INTRODUCTION
Overview
In this user’s manual, it will not only tell you how to install and connect your network system but
configure and monitor GEP-2681/GEP-2682 through the web by (RJ-45) serial interface and Ethernet
ports step-by-step. Many explanations in detail of hardware and software functions are shown as well
as the examples of the operation for web-based interface.
The next generation Web managed switches from Manufacture, is a portfolio of affordable
managed switches that provides a reliable infrastructure for your business network. These switches
deliver more intelligent features you need to improve the availability of your critical business
applications, protect your sensitive information, and optimize your network bandwidth to deliver
information and applications more effectively. It provides the ideal combination of affordability and
capabilities for entry level networking includes small business or enterprise application and helps you
create a more efficient, better-connected workforce.
GEP-2681/GEP-2682 Web Managed Switches provide 26 ports in a single device; the
specification is highlighted as follows.
L3 Lite features provide better manageability, security, QoS, and performance.
Support IPv4/IPv6 dual stack management
Support SSH/SSL secured management
Support SNMP v1/v2c/v3
Support RMON groups 1,2,3,9
Support sFlow
Support IGMP v1/v2/v3 Snooping
Support MLD v1/v2 Snooping
Support RADIUS and TACACS+ authentication
Support IP Source Guard
Support DHCP Relay (Option 82)
Support DHCP Snooping
Support ACL and QCL for traffic filtering
Support 802.1d(STP), 802.1w(RSTP) and 802.1s(MSTP)
Support LACP and static link aggregation
Support Q-in-Q double tag VLAN
Support GVRP dynamic VLAN
Overview of this user’s manual
Chapter 1 “Operation of Web-based Management”
Chapter 2 “System Configuration”
Chapter 3 “Configuration”
Chapter 4 “Security”
Chapter 5 “Maintenance”
2
Initial
Configuration
This chapter instructs you how to configure and manage the GEP-2681/GEP-2682
through the web user interface. With this facility, you can easily access and monitor
through any one port of the switch all the status of the switch, including MIBs status,
each port activity, Spanning tree status, port aggregation status, multicast traffic, VLAN
and priority status, even illegal access record and so on.
The default values of GEP-2681/GEP-2682 are listed in the table below:
IP Address
192.168.1.1
Subnet Mask
255.255.255.0
Default Gateway
192.168.1.254
Username
admin
Password
admin
After GEP-2681/GEP-2682 has been finished configuration the it interface, you can
browse it. For instance, type http://192.168.1.1 in the address row in a browser, it will
show the following screen and ask you inputting username and password in order to
login and access authentication.
The default username is “admin” and password is“admin”. For the first time to use,
please enter the default username and password, and then click the <Login> button.
The login process now is completed. In this login menu, you have to input the complete
username and password respectively, the GEP-2681/GEP-2682 will not give you a
shortcut to username automatically. This looks inconvenient, but safer.
In GEP-2681/GEP-2682, allowed two or more users using administrator’s identity to
manage this switch, which administrator to do the last setting, it will be an available
configuration to effect the system.
NOTE:
When you login the Switch WEB/CLI to manager. You must first type the
Username of the admin. Password was blank, so when you type after the end
Username, please press enter. Management page to enter WEB/CLI.
When you login GEP-2681/GEP-2682 switch Web UI management, you can use
both ipv4 ipv6 login to manage
To optimize the display effect, we recommend you use Microsoft IE 6.0 above,
Netscape V7.1 above or FireFox V1.00 above and have the resolution
1024x768. The switch supported neutral web browser interface
Chapter 1
Operation of Web-based Management
5
Figure 1 The login page
6
Chapter 2 System Configuration
This chapter describes the entire basic configuration tasks which includes the System Information and
any manage of the Switch (e.g. Time, Account, IP, Syslog and NTP.)
2-1 System
You can identify the system by configuring the contact information, name, and location of the
switch.
2-1.1 Information
The switch system’s contact information is provided here.
Web interface
To configure System Information in the web interface:
1. Click Configuration, System, and Information.
2. Write System Contact, System Name, System Location information in this page.
3. Click Apply
Figure 2-1.1: System Information
Parameter description:
System Contact:
The textual identification of the contact person for this managed node, together with
information on how to contact this person. The allowed string length is 0 to 128, and the
allowed content is the ASCII characters from 32 to 126.
System name:
An administratively assigned name for this managed node. By convention, this is the node's
7
fully-qualified domain name. A domain name is a text string drawn from the alphabet
(A-Za-z), digits (0-9), minus sign (-). No space characters are permitted as part of a name.
The first character must be an alpha character. And the first or last character must not be a
minus sign. The allowed string length is 0 to 128.
System Location:
The physical location of this node(e.g., telephone closet, 3rd floor). The allowed string
length is 0 to 128, and the allowed content is the ASCII characters from 32 to 126.
7
2-1.2 IP
The IPv4 address for the switch could be obtained via DHCP Server for VLAN 1. To manually
configure an address, you need to change the switch's default settings to values that are
compatible with your network. You may also need to establish a default gateway between the
switch and management stations that exist on another network segment.
Configure the switch-managed IP information on this page
Configure IP basic settings, control IP interfaces and IP routes.
The maximum number of interfaces supported is 8 and the maximum number of routes is 32.
Web Interface
To configure an IP address in the web interface:
1. Click Configuration, System, IP.
2. Click Add Interface then you can create new Interface on the switch.
3. Click Add Route then you can create new Route on the switch
4. Click Apply
Figure2-1.2: The IP configuration
8
Parameter description:
IP Configuration
Mode:
Configure whether the IP stack should act as a Host or a Router. In Host mode, IP traffic
between interfaces will not be routed. In Router mode traffic is routed between all interfaces.
DNS Server
This setting controls the DNS name resolution done by the switch. The following modes are
supported:
• From any DHCP interfaces
The first DNS server offered from a DHCP lease to a DHCP-enabled interface will be
used.
• No DNS server
No DNS server will be used.
• Configured
Explicitly provide the IP address of the DNS Server in dotted decimal notation.
• From this DHCP interface
Specify from which DHCP-enabled interface a provided DNS server should be
preferred.
DNS Proxy
When DNS proxy is enabled, system will relay DNS requests to the currently configured DNS
server, and reply as a DNS resolver to the client devices on the network.
IP Interfaces
Delete
Select this option to delete an existing IP interface.
VLAN
The VLAN associated with the IP interface. Only ports in this VLAN will be able to access the
IP interface. This field is only available for input when creating an new interface.
IPv4 DHCP Enabled
Enable the DHCP client by checking this box. If this option is enabled, the system will
configure the IPv4 address and mask of the interface using the DHCP protocol. The DHCP
client will announce the configured System Name as hostname to provide DNS lookup.
IPv4 DHCP Fallback Timeout
The number of seconds for trying to obtain a DHCP lease. After this period expires, a
configured IPv4 address will be used as IPv4 interface address. A value of zero disables the
fallback mechanism, such that DHCP will keep retrying until a valid lease is obtained. Legal
values are 0 to 4294967295 seconds.
IPv4 DHCP Current Lease
For DHCP interfaces with an active lease, this column show the current interface address, as
provided by the DHCP server.
IPv4 Address
The IPv4 address of the interface in dotted decimal notation.
If DHCP is enabled, this field is not used. The field may also be left blank if IPv4 operation
on the interface is not desired.
IPv4 Mask
9
The IPv4 network mask, in number of bits (prefix length). Valid values are between 0 and 30
bits for a IPv4 address.
If DHCP is enabled, this field is not used. The field may also be left blank if IPv4 operation
on the interface is not desired.
IPv6 Address
The IPv6 address of the interface. A IPv6 address is in 128-bit records represented as eight
fields of up to four hexadecimal digits with a colon separating each field (:). For example,
fe80::215:c5ff:fe03:4dc7. The symbol :: is a special syntax that can be used as a shorthand
way of representing multiple 16-bit groups of contiguous zeros; but it can appear only once.
It can also represent a legally valid IPv4 address. For example, ::192.1.2.34.
The field may be left blank if IPv6 operation on the interface is not desired.
IPv6 Mask
The IPv6 network mask, in number of bits (prefix length). Valid values are between 1 and
128 bits for a IPv6 address.
The field may be left blank if IPv6 operation on the interface is not desired.
IP Routes
Delete
Select this option to delete an existing IP route.
Network
The destination IP network or host address of this route. Valid format is dotted decimal
notationor a valid IPv6 notation. A default route can use the value 0.0.0.0or IPv6 :: notation.
Mask Length
The destination IP network or host mask, in number of bits (prefix length). It defines how
much of a network address that must match, in order to qualify for this route. Valid values
are between 0 and 32 bits respectively 128 for IPv6 routes. Only a default route will have a
mask length of 0 (as it will match anything).
Gateway
The IP address of the IP gateway. Valid format is dotted decimal notationor a valid IPv6
notation. Gateway and Network must be of the same type.
Next Hop VLAN (Only for IPv6)
The VLAN ID (VID) of the specific IPv6 interface associated with the gateway.
The given VID ranges from 1 to 4094 and will be effective only when the corresponding
IPv6 interface is valid.
If the IPv6 gateway address is link-local, it must specify the next hop VLAN for the gateway.
If the IPv6 gateway address is not link-local, system ignores the next hop VLAN for the
gateway.
Buttons
Add Interface:
Click to add a new IP interface. A maximum of 8 interfaces is supported.
Add Route:
Click to add a new IP route. A maximum of 32 routes is supported.
Apply:
Click to save changes.
Reset:
Click to undo any changes made locally and revert to previously saved values.
10
2-1.3 NTP
NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean
Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an
user-defined NTP server as well as Time Zone, the switch will sync the time in a short after
pressing <Apply> button. Though it synchronizes the time automatically, NTP does not update
the time periodically without user’s processing.
Time Zone is an offset time off GMT. You have to select the time zone first and then perform
time sync via NTP because the switch will combine this time zone offset and updated NTP time
to come out the local time, otherwise, you will not able to get the correct time. The switch
supports configurable time zone from –12 to +13 step 1 hour.
Default Time zone: +8 Hrs.
Web Interface
To configure NTP in the web interface:
1. Click Configuration, System, NTP.
2. Specify the Time parameter in manual parameters.
3. Click Apply.
Figure 2-1.3: The NTP configuration
Parameter description:
Mode :
Indicates the NTP mode operation. Possible modes are:
Enabled: Enable NTP client mode operation.
Disabled: Disable NTP client mode operation.
Server 1 to 5 :
Provide the NTP IPv4 or IPv6 address of this switch. IPv6 address is in 128-bit records
represented as eight fields of up to four hexadecimal digits with a colon separating each field
(:). For example, 'fe80::215:c5ff:fe03:4dc7'. The symbol '::' is a special syntax that can be
11
used as a shorthand way of representing multiple 16-bit groups of contiguous zeros; but it
can only appear once. It can also represent a legally valid IPv4 address. For example,
'::192.1.2.34'.
Buttons
These buttons are displayed on the NTP page:
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
11
2-1.4 Time
The switch provides manual and automatic ways to set the system time via NTP. Manual
setting is simple and you just input “Year”, “Month”, “Day”, “Hour” and “Minute” within the
valid value range indicated in each item.
Web Interface
To configure Time in the web interface:
1. Click Configuration, System and Time
2. Specify the Time parameter.
3. Click Apply.
Figure 2-1.4: The time configuration
12
Parameter description:
Time Configuration
Clock Source:
There are two modes for configuring how the Clock Source from. Select "Use Local Settings" :
Clock Source from Local Time. Select "Use NTP Server" : Clock Source from NTP Server.
System Date:
Show the current time of the system. The year of system date limits between 2011 and 2037.
Time Zone Configuration
Time Zone:
Lists various Time Zones world wide. Select appropriate Time Zone from the drop down and
click Apply to set.
Acronym:
User can set the acronym of the time zone. This is a User configurable acronym to identify
the time zone. ( Range : Up to 16 characters )
Daylight Saving Time Configuration
Daylight Saving Time:
This is used to set the clock forward or backward according to the configurations set below
for a defined Daylight Saving Time duration. Select 'Disable' to disable the Daylight Saving
Time configuration. Select 'Recurring' and configure the Daylight Saving Time duration to
repeat the configuration every year. Select 'Non-Recurring' and configure the Daylight
Saving Time duration for single time configuration. ( Default : Disabled ).
13
Recurring Configuration
Start time settings:
Week - Select the starting week number.
Day - Select the starting day.
Month - Select the starting month.
Hours - Select the starting hour.
Minutes - Select the starting minute.
End time settings:
Week - Select the ending week number.
Day - Select the ending day.
Month - Select the ending month.
Hours - Select the ending hour.
Minutes - Select the ending minute.
Offset settings:
Offset - Enter the number of minutes to add during Daylight Saving Time. ( Range: 1 to
1440 )
NOTE: The under “Start Time Settings” and “End Time Settings” was
displayed what you set on the “Start Time Settings” and “End Time
Settings” field information.
Buttons
These buttons are displayed on the NTP page:
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
14
2-1.5 Log
The log is a standard for logging program messages . It allows separation of the software that
generates messages from the system that stores them and the software that reports and
analyzes them. It can be used as well a generalized informational, analysis and debugging
messages. It is supported by a wide variety of devices and receivers across multiple platforms.
Web Interface
To configure log configuration in the web interface:
1. Click Configuration, System and log.
2. Specify the syslog parameters include IP Address of Syslog server and Port number.
3. Evoke the Syslog to enable it.
4. Click Apply.
Figure2-1.5: The System Log configuration
Parameter description:
Server Mode :
Indicate the server mode operation. When the mode operation is enabled, the syslog
message will send out to syslog server. The syslog protocol is based on UDP communication
and received on UDP port 514 and the syslog server will not send acknowledgments back
sender since UDP is a connectionless protocol and it does not provide acknowledgments.
The syslog packet will always send out even if the syslog server does not exist. Possible modes
are:
Enabled: Enable server mode operation.
Disabled: Disable server mode operation.
Server Address :
Indicates the IPv4 hosts address of syslog server. If the switch provide DNS feature, it also
can be a host name.
Buttons
These buttons are displayed on the NTP page:
Apply – Click to save changes.
Reset - Click to undo any changes made locally and revert to previously saved values.
2-2 Green Ethernet
EEE is a power saving option that reduces the power usage when there is low or no traffic
utilization.
15
EEE works by powering down circuits when there is no traffic. When a port gets data to be
transmitted all circuits are powered up. The time it takes to power up the circuits is named
wakeup time. The default wakeup time is 17 us for 1Gbit links and 30 us for other link speeds.
EEE devices must agree upon the value of the wakeup time in order to make sure that both the
receiving and transmitting device has all circuits powered up when traffic is transmitted. The
devices can exchange wakeup time information using the LLDP protocol.
EEE works for ports in auto-negotiation mode, where the port is negotiated to either 1G or 100
Mbit full duplex mode.
For ports that are not EEE-capable the corresponding EEE checkboxes are grayed out and thus
impossible to enable EEE for.
When a port is powered down for saving power, outgoing traffic is stored in a buffer until the
port is powered up again. Because there are some overhead in turning the port down and up,
more power can be saved if the traffic can be buffered up until a large burst of traffic can be
transmitted. Buffering traffic will give some latency in the traffic.
Web Interface
To configure a Port Power Saving Configuration in the web interface:
1. Click Configuration, Green Ethernet
2. Evoke to enable or disable the ActiPHY, PerfectReach, EEE and EEE Urgent Queues .
3. Click Apply.
Figure 2-2.1: The Port Power Saving Configuration
16
Parameter description:
Optimize EEE for
The switch can be set to optimize EEE for either best power saving or least traffic latency.
Port:
The switch port number of the logical port.
ActiPHY :
Link down power savings enabled.
ActiPHY works by lowering the power for a port when there is no link. The port is power up
for short moment in order to determine if cable is inserted.
PerfectReach :
Cable length power savings enabled.
EEE :
PerfectReach works by determining the cable length and lowering the power for ports with
short cables.
Controls whether EEE is enabled for this switch port.
For maximizing power savings, the circuit isn't started at once transmit data is ready for a
port, but is instead queued until a burst of data is ready to be transmitted. This will give some
traffic latency.
If desired it is possible to minimize the latency for specific frames, by mapping the frames to
a specific queue (done with QOS), and then mark the queue as an urgent queue. When an
urgent queue gets data to be transmitted, the circuits will be powered up at once and the
latency will be reduced to the wakeup time.
EEE Urgent Queues :
Queues set will activate transmission of frames as soon as data is available. Otherwise the
queue will postpone transmission until a burst of frames can be transmitted.
2-3 Ports Configuration
The section describes to configure the Port detail parameters of the switch. Others you could
using the Port configure to enable or disable the Port of the switch. Monitor the ports content
or status in the function.
2-3.1 Ports
This page displays current port configurations. Ports can also be configured here.
Web Interface
To configure a Current Port Configuration in the web interface:
1. Click Configuration, Ports Configuration, and Ports
2. Specify the Speed Configured, Flow Control, Maximum Frame size, Excessive Collision mode
and Power Control.
3. Click Apply.
Figure 2-3.1: The Port Configuration
Parameter description:
Port :
This is the logical port number for this row.
19
Link :
The current link state is displayed graphically. Green indicates the link is up and red that it is
down.
Current Link Speed :
Provides the current link speed of the port.
Configured Link Speed :
Selects any available link speed for the given switch port. Only speeds supported by the
specific port is shown. Possible speeds are:
Disabled - Disables the switch port operation.
Auto - Port auto negotiating speed with the link partner and selects the highest speed that
is compatible with the link partner.
10Mbps HDX - Forces the cu port in 10Mbps half duplex mode.
10Mbps FDX - Forces the cu port in 10Mbps full duplex mode.
100Mbps HDX - Forces the cu port in 100Mbps half duplex mode.
100Mbps FDX - Forces the cu port in 100Mbps full duplex mode.
1Gbps FDX - Forces the port in 1Gbps full duplex
2.5Gbps FDX - Forces the Serdes port in 2.5Gbps full duplex mode.
SFP_Auto_AMS - Automatically determines the speed of the SFP. Note: There is no
standardized way to do SFP auto detect, so here it is done by reading the SFP rom. Due to
the missing standardized way of doing SFP auto detect some SFPs might not be detectable.
The port is set in AMS mode. Cu port is set in Auto mode.
100-FX - SFP port in 100-FX speed. Cu port disabled.
100-FX_AMS - Port in AMS mode. SFP port in 100-FX speed. Cu port in Auto mode.
1000-X - SFP port in 1000-X speed. Cu port disabled.
1000-X_AMS - Port in AMS mode. SFP port in 1000-X speed. Cu port in Auto mode. Ports in
AMS mode with 1000-X speed has Cu port preferred. Ports in AMS mode with 100-FX speed
has fiber port preferred.
Flow Control :
When Auto Speed is selected on a port, this section indicates the flow control capability that
is advertised to the link partner. When a fixed-speed setting is selected, that is what is used.
The Current Rx column indicates whether pause frames on the port are obeyed, and the
Current Tx column indicates whether pause frames on the port are transmitted. The Rx and
Tx settings are determined by the result of the last Auto-Negotiation.
Check the configured column to use flow control. This setting is related to the setting for
Configured Link Speed.
Maximum Frame Size :
Enter the maximum frame size allowed for the switch port, including FCS.
Excessive Collision Mode :
Configure port transmit collision behavior.
Discard: Discard frame after 16 collisions (default).
Restart: Restart backoff algorithm after 16 collisions.
Buttons
20
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved values.
Upper right icon (Refresh)
You can click them for refresh the Port link Status by manual
21
2-3.2 Ports Description
The section describes to configure the Port’s alias or any descriptions for the Port Identity. It
provides user to write down an alphanumeric string describing the full name and version
identification for the system’s hardware type, software version, and networking application
Web Interface
To configure a Port Description in the web interface:
1. Click Configuration, Port, then Port Description
2. Specify the detail Port alias or description an alphanumeric string describing the full name
and version identification for the system’s hardware type, software version, and networking
application.
3. Click Apply.
Figure 2-3.2: The Port Configuration
Parameter description:
Port :
This is the logical port number for this row.
Description :
Enter up to 47 characters to be descriptive name for identifies this port.
Buttons
Apply – Click to save changes.
Reset- Click to undo any changes made locally and revert to previously saved values.
Loading...