Page 1
1
LevelOne
FUS-3101
USB MFP Server
User Manual
V1.0
Page 2
2
Table of Contents
CHAPTER1 INTRODUCTION................................ .......................................................................3
1.1 About the Printer Server Described in this Manual ............................... 3
1.2 Customer Support ................................................................ .................... 3
CHAPTER2 PRODUCT OVERVIEW ........................................................................................... 4
2.1 Package Contents ................................ .................................................... 4
2.2 Product CD................................................................................................ 4
2.2.1 Start-up Procedures ................................ .............................................. 4
2.3 Physical Description................................................................................. 4
2.4 Supported USB Devices ................................ .......................................... 4
CHAPTER3 BASIC INSTALLATION ................................ ...........................................................5
3.1 Connecting the Hardware ........................................................................ 5
3.3 Assigning an IP Address to the Server................................................... 6
3.3.1 Preliminary ................................ ................................................................ 6
3.3.2 IP Address................................................................ ................................. 7
3.3.3 Methods for Setting the IP Address ........................................................ 7
3.3.4 Server Names and Server Name Rules................................................. 7
3.3.5 Setting the IP Address Using DHCP....................................................... 7
3.3.6 Setting the IP Address Using the Control Center.................................. 7
CHAPTER4 USING THE USB DEVICE SERVER................................................................ .... 10
4.1 Introduction ................................................................ ............................. 10
4.2 Connect & Disconnect ........................................................................... 10
4.3 Subnet Issue........................................................................................... 10
4.4 Installation of USB Device Driver...........................................................11
4.5 Using the USB Device Server ............................................................... 13
4.6 Auto-Connect Printer.............................................................................. 15
4.7 Network Scanner .................................................................................... 18
4.9 Request to Connect ............................................................................... 20
4.10 Quitting the Control Center................................ .................................... 20
4.11 Limitations ............................................................................................... 20
CHAPTER5 THE SERVER’S WEB PAGES..................................................................................... 22
5.1 Introduction ................................................................ ............................. 22
5.2 Using the Server’s Web Pages ............................................................. 22
5.2.1 Displaying Server Status................................................................ ........ 22
5.2.2 Setting up Server Configuration................................ ............................ 23
CHAPTER6 TROUBLESHOOTING................................................................ ........................... 25
6.1 LED Indicators ................................................................ ........................ 25
6.2 Firewall .................................................................................................... 25
CHAPTER7 RESTORE FACTORY DEFAULTS ................................ .......................................26
7.1 Using the Server’s Web Pages ............................................................. 26
7.2 Using Init Button ................................................................ ..................... 26
7.3 Default Parameters List ................................ ......................................... 26
CHAPTER8 UPGRADE FIRMWARE......................................................................................... 28
CHAPTER9 THE INIT BUTTON ................................................................................................. 30
Page 3
3
Chapter1 Introduction
Thank you for purchasing FUS-3101 USB MFP Server (in the following referred to as “Server”).
This Server is designed to connect your Multifunction Printer, Scanner, Fax, Multifunction Printer,
to your network, allowing all network users’ access to these shared USB devices.
1.1 About the Printer Server Described in this Manual
This manual provides introductory information as well as detailed instructions on how to set up
and manage LevelOne USB MFP Server in various network environments.
To fully benefit from this document, you should be familiar with basic networking principles. The
instructions described in this manual are based on the settings in a new Server. To reload the
Factory Parameters, you can reset this Server back to Factory Default, which will restore most of
the settings. For details, please refer to the chapter “Restore Factory Defaults”.
1.2 Customer Support
Should you require any technical assistance, please contact your product reseller. Or you can
visit our website at http://www.level.com for latest product information.
This document is subject to changes without prior notice.
Page 4
4
Chapter2 Product Overview
2.1 Package Contents
Verify that nothing is missing from the package by using the checking list below. Please contact
your dealer if anything is missing or damaged. All packing materials are recyclable. Please
confirm the items in the package below:
FUS-3101
Power Adapter
Quick Installation Guide
CD Manual/Utility
2.2 Product CD
This CD provides easy-to-use Control Center software, and the User’s Manual and Quick
Installation Guide.
2.2.1 Start-up Procedures
If your computer is configured to auto start CDs, this CD will start automatically when inserted.
You can also navigate to the CD and start the autorun.exe file from within the Windows file
manager.
2.3 Physical Description
1. Power Adaptor Connector: for DC IN 12V/1A power adaptor
2. Init Button: for restoring the parameters to the default values
3. Ethernet Connector: connected to a twisted pair category 5 cable
4. USB Host Ports: USB 1.1/2.0 low, full, and Hi-Speed compliant
5. Indicators
Power Indicator is lit while power is applied. If it is not lit, or if it blinks, there is a
problem with this Server or power adapter.
Link Status is lit while network is applied. If it is not lit, it indicates that this server
does not connect to the network.
Status Indicator blinks to indicate network activity.
LAN Indicator blinks to indicate wired network activity. If it is lit, it indicates the
wired network is applied. If it is not lit, it indicates that the server does not connect
to the wired network.
USB Indicator is lit while a USB device connects to a USB Port of this Server. If it
is not lit, or if it blinks, there is a problem with the USB device or this Server.
2.4 Supported USB Devices
The LevelOne USB device server supports the following types of USB devices.
USB Printer
USB multifunction printer (MFP/AIO)
Page 5
5
Chapter3 Basic Installation
3.1 Connecting the Hardware
1. Make sure that your USB devices are switched off and that the Server’s Power Adapter
is disconnected.
2. Connect the USB devices to the USB port with the USB cable.
3. Connect the Server to the network with a twisted-pair category 5 cable, 10baseT or
100baseTX.
4. Turn on the USB device and make sure it is ready for use.
5. Connect the Power Adapter to the Server. The power indicator will light up and USB
indicator will flash in turn. When the Link indicator lights up, the Server is correctly
connected to the network. When USB indicator stops flashing, the Server starts to work
normally.
1. Double click the highlighted server (or click the “Configure Server” button) to get the
server’s web pages. Click CONFIG icon.
Page 6
6
2. Login with administrator ID (default: admin) and its password (default: admin).
3. Click Submit to save your settings. And the server will reboot
4. You have now finished the procedure of setting the wireless parameters.
After properly configuring the wireless parameters, you can remove the network cable and
reboot the Printer Server. LevelOne Printer Server will then connect to your wireless network.
And it will detect if a network cable is plugged-in or not. If a network cable is plugged-in, the
Printer Server will always connect to the network through the network cable. Otherwise it will
always connect to the network through wireless module. Once the Printer Server connects to
the network, all operations to use USB device server are exactly the same.
3.3 Assigning an IP Address to the Server
3.3.1 Preliminary
If you have a DHCP server on your network, your Server will receive an IP address
automatically. The IP address will then appear on the Control Center or on the page of
configuration report that you printed earlier. If your DHCP server does not give an IP
address to the Server, the Server will use the automatic private IP addressing IP:
Page 7
7
169.254.0.0. ~ 169.254.255.255
If you are not working in a DHCP network, you need to manually set the Server’s IP
address.
3.3.2 IP Address
Unless you are assigning an IP address using DHCP, you must obtain an unused IP address
from your network administrator.
3.3.3 Methods for Setting the IP Address
You can set the IP address of your Server using one of the following methods, depending on your
network operating environment:
Automatic IP Address Assignment
Manual IP Address Assignment
3.3.4 Server Names and Server Name Rules
The default server name of the Server is “LevelOne”. If you put two or more Servers in your local
area network, to avoid using the same server names you have to change the server names by
using the Control Center or the Server’s web pages. If your server name is longer than 15
characters, the Server uses only the first 15 characters.
3.3.5 Setting the IP Address Using DHCP
Follow the instructions below to get an IP address using DHCP:
1. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included
in this scope should contain the following parameters:
range of IP addresses
subnet mask
default router IP address
DNS server IP address
lease duration
2. Activate the scope. The Server automatically gets the DHCP parameters. If you are using
DNS, you may include at least one DNS server IP address in the DHCP scope or manually
set the DNS server IP address using Server’s web pages or the Control Center.
3.3.6 Setting the IP Address Using the Control Center
1. Install the Control Center. The Control Center is available on the Product CD.
2. Start the Control Center and Auto-searching Server window will appear.
3. If the tool finds multiple Servers in your local area network, then you have to select one
Server from the Server List.
Page 8
8
4. Double click the highlighted server (or click the “Configure Server” button) to get the
server’s web pages. Click CONFIG icon.
5. Login with administrator ID (default: admin) and its password (default: admin).
Page 9
9
6. Click the button corresponding to your choice of IP setting methods (static or dynamic
using DHCP). When assigning a static IP address you also have to define Subnet Mask.
7. Click Submit to save your settings. And the Server will reboot. You have now finished the
procedure of setting the IP address.
Page 10
10
Chapter4 Using the USB Device Server
4.1 Introduction
The goal of this product is to provide the USB device server in a single product. We developed a
new technology called “NetUSB” to achieve this goal. Basically, the “NetUSB” is a “USB over IP”
technology that transparently redirects all USB packets to TCP/IP network channel. “NetUSB”
allows you to use USB devices as if they were connected directly to your PC although they are
actually remotely connected to the LevelOne Printer Server USB device server.
4.2 Connect & Disconnect
“NetUSB” allows you to use USB devices as if they were connected directly to your PC although
they are actually remotely connected to the LevelOne USB Printer Server. The “connect”
operation is a software operation that simulates an actual USB device plug-in. That is to say,
when you do a “
connect” operation in the Control Center, PC can then detect a USB device’s
plug-in, although actually you do not plug in any USB device. Similarly, the “disconnect”
operation is a software operation that simulates the disconnection of the USB device. Once the
connect operation is successful, the operations to use that USB device are just the same as if the
USB device is directly connected to the PC.
If a USB device is “connected” by a PC, we say that PC has the ownership of the USB device.
Only one PC can get the ownership of a USB device at the same time. Therefore, if a USB
device is connected by one PC, no other PC can connect this USB device until this USB device
is disconnected.
4.3 Subnet Issue
Before using the NetUSB technology, you must first make sure that your PC can access
LevelOne USB device server via TCP/IP. The simplest way to do this is using “Control Center” to
search for the LevelOne USB device server on the network and change its IP address to be the
same subnet as your PC. If the server and your PC are not in the same TCP/IP subnet, Control
Center will show the server in red, as the following figure. You must change the IP address (or
using DHCP) of the server so that the server and your PC are in the same subnet. Control Center
will show these servers in blue, meaning you can access these servers by the NetUSB
technology.
Page 11
11
4.4 Installation of USB Device Driver
Some USB devices, like printers or MFPs (multifunction printers), require to install
vendor-supplied driver (usually on CDROM). For those USB devices that do not need to install
driver, please skip this section.
A. Insert the CDROM into the CD drive and run the “autorun” program.
B. Follow the instructions of the installation program to install driver.
C. When the installation program asks you to plug-in the USB device, run the “Control Center”.
D. In the Control Center, click the USB device server that has the desired USB device
attached.
E. Click the desired USB device as the following figure.
Page 12
12
F. Click the “Connect” button. Then the message “Manually Connect by
your_computer_name” will be shown, as the following figure.
G. Now, the installation program will detect the USB device and continue to install driver.
H. After the installation is completed, click the USB device in the Control Center and then click
the “Disconnect” button to disconnect the USB device.
Page 13
13
Now the driver of your USB device is installed.
4.5 Using the USB Device Server
A. In the Control Center, click the USB device server that has the desired USB device attached.
B. Click the desired USB device.
C. Click the “Connect” button. Then the message “Manually Connect by
your_computer_name” will be shown.
Page 14
14
D. Now, PC will detect the plug-in of the USB device. The “connect” operation is a software
operation that simulates an actual USB device plug-in. That is to say, when you do a
“connect” operation in the Control Center, PC can then detect a USB device’s plug-in,
although actually you do not plug in any USB device.
E. Then, just use the USB device as if it is connected directly to your PC’s USB port.
F. After you finish using the USB device, click the USB device in the Control Center and then
click the “Disconnect” button to disconnect the USB device. Other PCs can not “Connect”
the USB device until you “Disconnect” that USB device. That is to say, only one PC is
allowed to connect the USB device at the same time.
Page 15
15
4.6 Auto-Connect Printer
The method described in section 4.5 is so-called manual-connect, which means users must
manually connect the USB device before using that device, and must manually disconnect the
USB device after using the device, otherwise nobody else can connect this device. However, for
printers and scanners (and MFPs), the USB device server supports auto-connect so users don’t
need to manually connect/disconnect. This and the next sections show you how to do this.
After the driver is installed as described in section 4.4, you can see a newly created printer in the
Control Panel’s “Printers and Faxes”. Follow the steps below to do a NetUSB auto-connect
printing.
A. In the Control Center, click the USB device server that has the desired printer (or MFP)
attached.
B. Click the desired printer (or MFP).
C. Click the “Auto Connect Printer” button and choose “Set Auto-Connect Printer”.
Page 16
16
The following figure will appear.
D. Choose the desired printer. The desired printer must be the Windows printer (this is a logical
printer) that matches the printer attached on the USB device server (this is a physical
printer). Then click the “Apply” button.
E. Then, the printer will be marked as an “Auto-Connected Printer” in red. If you choose
“Auto-Connected Printer List” in the “Tools” menu, you can see a newly created item that
describes the association between the Windows printer and the physical printer on the
server.
Page 17
17
F. Then try to issue a print job to the desired printer. You will see the Control Center will
automatically do a connect operation. Then, the print job will be issued to that printer.
G. Even you already properly setup an auto-connected printer, the Control Center must be
running (in the background) while a print job is issued. This means you’d better run the
Control Center every time after you login Windows. In order to skip this manual operation,
you can make the Control Center be run automatically after you login Windows. To do this,
choose the “Configuration” item in the “Tools” menu. The following window will appear. Click
on the check box and then on the “OK” button. This feature is enabled by default.
Page 18
18
If you would like to break the association between the Windows printer and the physical printer,
just click on the association and click the “Delete” button in the “Auto
-Connected Printer List”.
4.7 Network Scanner
For NetUSB scanning, we recommend you use Network Scanner as the following steps.
A. In the Control Center, click the USB device server that has the desired MFP (or scanner)
attached.
B. Click the desired MFP (or scanner).
C. Click the “Network Scanner” button. Then you can see that the Control Center will
automatically do a “connect” operation. The following window will appear.
Page 19
19
D. Choose one of TWAIN or WIA item. Click “OK”. The following window will appear.
E. Follow the usual steps to do scanning.
F. After the scanning, close the “Auto-Connect Scanner” window. At this moment, Control
Center will automatically do a disconnect.
Page 20
20
4.9 Request to Connect
If a USB device is manually connected by any other user, basically you can not connect that
device. However, we offer another mechanism called “Request to Connect” to solve this
inconvenience. For example, there are two computers – LEVELONE and TEST. Now the owner
of “HP Photosmart 2600” is LEVELONE. Then, the TEST computer wants to use this HP printer.
The user on the TEST computer can click the “Request to Connect” button in the Control Center.
The following window appears.
At this moment, the user on the LEVELONE computer will see the following window, indicating
that another computer – TEST is requesting to use the HP printer.
The user will choose to accept or reject. If accepted, the Control Center on LEVELONE will
automatically disconnect the device and the Control Center on TEST will automatically connect
that device.
4.10 Quitting the Control Center
The Control Center doesn’t really quit if you click the “X” box (close box) at the top right corner of
the window. Instead, it just minimizes itself to the system tray. There are two ways to really close
the Control Center. The first way is choosing “Exit” item in the “File” menu in the Control Center.
The second way is right-clicking the icon of the Control Center in the system tray and choosing
the “Exit” item.
4.11 Limitations
There are some limitations to use the NetUSB technology.
LevelOne
Page 21
21
A. Only supports Windows 2000/XP/2003/Vista/7. Windows 98/ME is not supported.
B. Only one PC can get the ownership of the same USB device at the same time.
Page 22
22
Chapter5 The Server’s Web Pages
5.1 Introduction
The Server runs the http server, httpd on TCP port: 80. Users may use the web pages to see
the Server’s system status and configure the Server.
5.2 Using the Server’s Web Pages
5.2.1 Displaying Server Status
Click on the “STATUS” icon to see system status and network status.
Page 23
23
5.2.2 Setting up Server Configuration
To set up the Server configuration, click on the “CONFIG” icon ad then the system will request
user to enter administrator (default: admin) and password (default: admin) to login.
General Configuration
Server Information: You have to set the Server Name, which is the name to
represent the Server.
TCP/IP: You have to set the Server’s TCP/IP configuration to connect TCP/IP
network. Please see Chapter 3 Basic Installation for more details.
UPnP Setting: Enable or disable the UPnP function.
Printer Server Setting: Enable or disable LPR, IPP and RawTCP printing protocol
to support HPLIP network printer.
Administrator: You can change administrator name and password. If you forgot
administrator name and password, you must perform Restore Factory Default action by
plugging in the power adaptor while pressing the Init button. Please refer to the chapter
“Restore Factory Defaults”.
Administrator: enter your desired administrator name.
New Password: enter your desired password.
Re-type Password: re-confirm the password.
Page 24
24
Maintenance If you want to restore factory default values of the Server or upgrade new
firmware, you can use the Maintenance tool.
Restart: click this button to restart (reboot) the Server.
Factory Default: click this button, the Server will restore factory default values.
Firmware Upgrade: click Browse to find the firmware file to be upgraded. Click
Upload to upload the firmware into the Server.
Page 25
25
Chapter6 Troubleshooting
This chapter provides useful information to help you resolve difficulties that you may experience
with your
Server. Fault symptoms, possible causes, and remedial actions are provided within a
quick reference table. This Server’s USB ports only support MFPs, printers, scanners, mass
storage, and USB cameras.
6.1 LED Indicators
Indicators Behavior Description
On Power On Power
Off Power off/System error
On Network connected Link
Off No physical connection to network
Blinking Activity on network Status
Off No activity on network
On USB device connected
Blinking Connected USB device error
USB
Off No physical connection to USB device
6.2 Firewall
If a firewall software has been installed on your PC, it may block the communication between the
PC and the USB device server so that the USB device server can not work properly. To solve this
problem, either disable the firewall or configure the firewall to allow the following TCP and UDP
ports:
7303, 7305, 20005, 30201, 30202, 30203
Page 26
26
Chapter7 Restore Factory Defaults
You may restore the Server’s default parameters by one of the following methods.
7.1 Using the Server’s Web Pages
1. Go to the Server’s web page and click CONFIG
2. Enter administrator (default: admin) and password (default: admin).
3. Click Maintenance.
4. Click Factory Default.
5. Click Yes to confirm
7.2 Using Init Button
Plug in the power adaptor while pressing the Init button until LED indicator of USB blink. After
that, plug off the power adaptor and then plug in the power adapter again to restart the Server.
Finally, the Server will operate using the Factory Default values.
7.3 Default Parameters List
General Information
Server Name: LevelOne
TCP/IP
Automatically get IP by DHCP: Enabled
Static IP: Disabled
- IP Address: 192.168.1.100
- Subnet Mask: 255.255.255.0
Page 27
27
User Accounts
Administrator: admin
Password: admin
Page 28
28
Chapter8 Upgrade Firmware
This chapter describes how to upgrade firmware. Please follow one of the following Procedures:
Procedure A: Using the Control Center
1. Open Control Center. It will automatically search the existing Servers and display their
statuses.
2. Select the Server that you want to upgrade the firmware. Double click the selected
Server to get the serve’s main web page.
3. Click CONFIG icon.
4. Login the Server with Administrator (default: admin) and Password (default: admin).
5. Click Maintenance.
6. Click Upgrade Firmware.
7. Click Browse button to choose the file of new firmware.
8. Click Upload button to start firmware upgrade.
9. Wait for 20 seconds for system reboot.
Procedure B: Using the Init Button and the TFTP Client
1. Plug in the power adaptor while pressing the Init button until LED indicator of USB1 blink.
Please note that after that, the Server will operate using the factory default values
after restarting, i.e., your Server’s configuration will recover to Factory Default
values.
2. Run the TFTP client Tool: Image Burner, from Windows Start menu.
3. Click Open Image to open your new firmware. Please note that you must configure your
PC’s TCP/IP such that PC and the Server belong to the same LAN, i.e. PC’s IP is
192.168.1.xxx and subnet mask is 255.255.255.0.
Page 29
29
4. Click Upload Image.
5. Wait for Image Uploading to finish and then click Close.
6. Plug-off the power adapter and then plug-in the power adapter to restart the Server.
Page 30
30
Chapter9 The Init Button
The Init button is used for maintenance: Simultaneously press Init button and turn on (by
plugging in the power adaptor) the Server until USB LED indicator simultaneously blink. After
that, the Server will do the following tasks:
A. Perform a Factory Default restoration of the server, which will restore most of the
parameters and settings to factory default values.
B. Perform a TFTP server. You can upgrade new firmware using any TFTP client tool.
Note: After performing the tasks mentioned above, you have to plug off the power adaptor and
then plug in the power adaptor to restart the Server.
Loading...